Duriron is (A) Acid resistant, brittle and very hard (B) High silicon iron (C) Prone to breakage due to thermal expansion because of its very high co￾efficient of thermal expansion (D) All (A), (B) and (C)

Duriron is
(A) Acid resistant, brittle and very hard
(B) High silicon iron
(C) Prone to breakage due to thermal expansion because of its very high co￾efficient of thermal expansion
(D) All (A), (B) and (C)
by

1 Answer

Answer :

(D) All (A), (B) and (C)
by

Related questions

The most resistant material to alkaline corrosion is (A) Duriron (B) Nickel (C) Aluminium (D) Karbate

Description : The most resistant material to alkaline corrosion is (A) Duriron (B) Nickel (C) Aluminium (D) Karbate

Last Answer : (B) Nickel

Very high sulphur in pig iron makes (A) Its casting unsound (B) Its hard and machinable (C) Its brittle and malleable (D) All (A), (B) & (C)

Description : Very high sulphur in pig iron makes (A) Its casting unsound (B) Its hard and machinable (C) Its brittle and malleable (D) All (A), (B) & (C)

Last Answer : (A) Its casting unsound

Plate towers are preferred to packed towers, when large temperature changes are involved, because of the reason that the (A) Packing may be crushed due to thermal expansion/contraction of the components of the equipments (B) Pressure drop in the equipment will be very high (C) Viscosity variation of the fluids may cause channelling/flooding (D) None of these

Description : Plate towers are preferred to packed towers, when large temperature changes are involved, because of the reason that the (A) Packing may be crushed due to thermal expansion/contraction of the ... C) Viscosity variation of the fluids may cause channelling/flooding (D) None of these

Last Answer : (A) Packing may be crushed due to thermal expansion/contraction of the components of the equipments

__________ glass has the lowest co-efficient of thermal expansion and hence is more heat resistant. (A) Pyrex (B) Soda lime (C) Lead (D) High silica

Description : __________ glass has the lowest co-efficient of thermal expansion and hence is more heat resistant. (A) Pyrex (B) Soda lime (C) Lead (D) High silica

Last Answer : (A) Pyrex

Silicon percentage in acid resistant cast iron is about (A) 4 (B) 8 (C) 14 (D) 20

Description : Silicon percentage in acid resistant cast iron is about (A) 4 (B) 8 (C) 14 (D) 20

Last Answer : (C) 14

Silicon percentage in acid resistant cast iron is about (A) 4 (B) 8 (C) 14 (D) 20

Description : Silicon percentage in acid resistant cast iron is about (A) 4 (B) 8 (C) 14 (D) 20

Last Answer : (A) 4

White cast iron as compared to grey cast iron is (A) More durable (B) Very brittle (C) Very hard (D) All (A), (B) & (C)

Description : White cast iron as compared to grey cast iron is (A) More durable (B) Very brittle (C) Very hard (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Crude oil is subjected to vacuum distillation in the last stage, because (A) High boiling point products like heavy fuel oil & lubricating oils are heat sensitive and may decompose (B) Lighter/low boiling products are prone to thermal decomposition (C) High purity products can be obtained thereby (D) None of these

Description : Crude oil is subjected to vacuum distillation in the last stage, because (A) High boiling point products like heavy fuel oil & lubricating oils are heat sensitive and may decompose (B) Lighter/low ... prone to thermal decomposition (C) High purity products can be obtained thereby (D) None of these

Last Answer : (A) High boiling point products like heavy fuel oil & lubricating oils are heat sensitive and may decompose

Solvay process is not used for the manufacture of potassium carbonate, because of the reason that potassium bicarbonate (A) Is prone to thermal decomposition (B) Has high water solubility and is unstable (C) Is soluble in ammonium chloride and potassium chloride solution (D) All (A), (B) and (C)

Description : Solvay process is not used for the manufacture of potassium carbonate, because of the reason that potassium bicarbonate (A) Is prone to thermal decomposition (B) Has high water solubility and is unstable (C) Is soluble in ammonium chloride and potassium chloride solution (D) All (A), (B) and (C)

Last Answer : (C) Is soluble in ammonium chloride and potassium chloride solution

In a gas-liquid shell and tube heat exchanger, the(A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure gases are corrosive in nature (C) Gases to be heated/cooled is normally routed through the shell side, because the corrosion caused by the cooling water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Description : In a gas-liquid shell and tube heat exchanger, the (A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure ... water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Zinc is highly __________ at room temperature. (A) Ductile (B) Resistant to atmospheric corrosion (C) Malleable (D) Brittle

Description : Zinc is highly __________ at room temperature. (A) Ductile (B) Resistant to atmospheric corrosion (C) Malleable (D) Brittle

Last Answer : (B) Resistant to atmospheric corrosion

Which of the following is an alloy of nickel and copper? (A) Hastelloy (B) Duriron (C) Monel (D) Inconel

Description : Which of the following is an alloy of nickel and copper? (A) Hastelloy (B) Duriron (C) Monel (D) Inconel

Last Answer : (C) Monel

Pick out the wrong statement. (A) Alloys are harder than their component elements (B) Presence of silicon in steel decreases its electrical resistance (C) Karbate is an acid resistant material of construction (D) Nichrome, a steel alloyed with 10% Ni and 20% Cr can be used upto a temperature of 1100°C

Description : Pick out the wrong statement. (A) Alloys are harder than their component elements (B) Presence of silicon in steel decreases its electrical resistance (C) Karbate is an acid resistant material of construction ... , a steel alloyed with 10% Ni and 20% Cr can be used upto a temperature of 1100°C

Last Answer : (B) Presence of silicon in steel decreases its electrical resistance

Dittus-Boelter equation used for the determination of heat transfer co￾efficient is valid (A) For fluids in laminar flow (B) For fluids in turbulent flow (C) When Grashoff number is very important (D) For liquid metals

Description : Dittus-Boelter equation used for the determination of heat transfer co￾efficient is valid (A) For fluids in laminar flow (B) For fluids in turbulent flow (C) When Grashoff number is very important (D) For liquid metals

Last Answer : (B) For fluids in turbulent flow

White cast iron is not (A) Malleable(B) Whitish in color(C) Brittle(D) Strong and hard

Description : White cast iron is not (A) Malleable (B) Whitish in color (C) Brittle (D) Strong and hard

Last Answer : (A) Malleable

Alloys having more than 80% copper are generally more (A) Abrasion resistant (B) Corrosion resistant (C) Prone to season cracking (D) Machinable

Description : Alloys having more than 80% copper are generally more (A) Abrasion resistant (B) Corrosion resistant (C) Prone to season cracking (D) Machinable

Last Answer : (B) Corrosion resistant

Silicon carbide is a/an (A) Adhesive (B) Abrasive (C) Type of glass (D) Brittle material

Description : Silicon carbide is a/an (A) Adhesive (B) Abrasive (C) Type of glass (D) Brittle material

Last Answer : (B) Abrasive

The elastic strain in copper is due to the (A) Motion of dislocations (B) Stretching of atomic bonds (C) Breakage of atomic bonds (D) None of the above

Description : The elastic strain in copper is due to the (A) Motion of dislocations (B) Stretching of atomic bonds (C) Breakage of atomic bonds (D) None of the above

Last Answer : Option A

Minimum shear reinforcement is necessary to [ A ] Prevent brittle shear failure [ B ] Prevent failure due to shrinkage and thermal stresses [ C ] Hold the reinforcements in place while pouring concrete [ D ] All the above.

Description : Minimum shear reinforcement is necessary to [ A ] Prevent brittle shear failure [ B ] Prevent failure due to shrinkage and thermal stresses [ C ] Hold the reinforcements in place while pouring concrete [ D ] All the above.

Last Answer : [ D ] All the above.

Brass tubes are used in the manufacture of tubes of evaporators used in sugar and salt industries, mainly because of its (A) High co-efficient of thermal expansion (B) Low thermal conductivity (C) High corrosion resistance (D) All (A), (B) and (C)

Description : Brass tubes are used in the manufacture of tubes of evaporators used in sugar and salt industries, mainly because of its (A) High co-efficient of thermal expansion (B) Low thermal conductivity (C) High corrosion resistance (D) All (A), (B) and (C)

Last Answer : (C) High corrosion resistance

Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)

Description : Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C

What is hard and brittle iron that is formed into a particular shape by pouring the liquid metal into a mold?

Description : What is hard and brittle iron that is formed into a particular shape by pouring the liquid metal into a mold?

Last Answer : I think it would be cast

H2SO4 (< 50% concentration) is corrosive to (A) Aluminium, mild steel, stainless steel, concrete & tin (B) Copper, cast iron & high silicon iron (14% Si) (C) Rubber (butyl and hard), silicone rubber & Teflon (D) Glass, graphite, porcelain & stoneware

Description : H2SO4 (< 50% concentration) is corrosive to (A) Aluminium, mild steel, stainless steel, concrete & tin (B) Copper, cast iron & high silicon iron (14% Si) (C) Rubber (butyl and hard), silicone rubber & Teflon (D) Glass, graphite, porcelain & stoneware

Last Answer : (A) Aluminium, mild steel, stainless steel, concrete & tin

Mercury filled thermometers should never be used to determine the temperature of the battery electrolyte because accidental breakage of the thermometer can cause __________________. A. severe sparking and explosions B. rapid oxidation of battery plates C. contamination of the electrolyte D. corrosion on the battery terminals

Description : Mercury filled thermometers should never be used to determine the temperature of the battery electrolyte because accidental breakage of the thermometer can cause __________________. A. severe sparking and ... of battery plates C. contamination of the electrolyte D. corrosion on the battery terminals

Last Answer : Answer: A

mmonium nitrate is (A) Having about 40% N2 (B) Not hygroscopic (C) Not prone to explosive thermal decomposition (D) Mixed with limestone powder to reduce its explosive nature before using it as a fertilizer

Description : mmonium nitrate is (A) Having about 40% N2 (B) Not hygroscopic (C) Not prone to explosive thermal decomposition (D) Mixed with limestone powder to reduce its explosive nature before using it as a fertilizer

Last Answer : (D) Mixed with limestone powder to reduce its explosive nature before using it as a fertilizer

A breakable, mercury-filled thermometer should not be used in a lead-acid battery to measure electrolyte temperature, as an accidental breakage can cause ____________. A. severe sparking and explosions B. rapid oxidation of battery plates C. violent gassing at the positive plates D. corrosion on the battery terminals

Description : A breakable, mercury-filled thermometer should not be used in a lead-acid battery to measure electrolyte temperature, as an accidental breakage can cause ____________. A. severe sparking and explosions ... battery plates C. violent gassing at the positive plates D. corrosion on the battery terminals

Last Answer : Answer: A

Oils are partially hydrogenated (not fully) to manufacture Vanaspati, because fully saturated solidified oils (A) Cause cholesterol build up and blood clotting (B) Are prone to rancid oxidation (C) Always contain some amount of nickel (as their complete removal is very difficult) (D) Have affinity to retain harmful sulphur compounds

Description : Oils are partially hydrogenated (not fully) to manufacture Vanaspati, because fully saturated solidified oils (A) Cause cholesterol build up and blood clotting (B) Are prone to rancid oxidation (C ... (as their complete removal is very difficult) (D) Have affinity to retain harmful sulphur compounds

Last Answer : (A) Cause cholesterol build up and blood clotting

Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Description : Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Last Answer : (D) Thermal co-efficient of expansion

Gray King Assay and Swelling Index of a coal is a measure of its (A) Swelling characteristics (B) Abradability (C) Agglutinating properties (D) Resistance to impact breakage

Description : Gray King Assay and Swelling Index of a coal is a measure of its (A) Swelling characteristics (B) Abradability (C) Agglutinating properties (D) Resistance to impact breakage

Last Answer : (A) Swelling characteristics

Ice is slippery when a man walks on it because a.Increase of pressure causes it to melt b.Ice is brittle c.There is no friction d.It is very chill e.Its surface is smooth

Description : Ice is slippery when a man walks on it because a.Increase of pressure causes it to melt b.Ice is brittle c.There is no friction d.It is very chill e.Its surface is smooth

Last Answer : a. Increase of pressure causes it to melt

Which of the following materials may prove unsuitable for handling acetic acid (glacial & anhydrous) at 40°C? (A) Silicone rubber, teflon, porcelain and wood (B) Nickel, monel, stainless steel and graphite (C) Aluminium, copper, high silicon iron (D) Brass, cast iron, mild steel and tin

Description : Which of the following materials may prove unsuitable for handling acetic acid (glacial & anhydrous) at 40°C? (A) Silicone rubber, teflon, porcelain and wood (B) Nickel, monel, stainless steel and graphite (C) Aluminium, copper, high silicon iron (D) Brass, cast iron, mild steel and tin

Last Answer : (D) Brass, cast iron, mild steel and tin

Neutraliser tank used for reacting nitric acid with ammonia for the production of ammonium nitrate is made of (A) Aluminium (B) Stainless steel (C) High silicon (14%) iron (D) Copper

Description : Neutraliser tank used for reacting nitric acid with ammonia for the production of ammonium nitrate is made of (A) Aluminium (B) Stainless steel (C) High silicon (14%) iron (D) Copper

Last Answer : (B) Stainless steel

Containers made of high silicon cast iron (14% Si) are not suitable for the storage of (A) Acetic acid (B) Benzoic & boric acids (C) Phosphoric acid (95%) & sulphuric acid (95%) (D) Hydrochloric acid (concentrated)

Description : Containers made of high silicon cast iron (14% Si) are not suitable for the storage of (A) Acetic acid (B) Benzoic & boric acids (C) Phosphoric acid (95%) & sulphuric acid (95%) (D) Hydrochloric acid (concentrated)

Last Answer : (D) Hydrochloric acid (concentrated)

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

According to the film theory of mass transfer, the mass transfer co￾efficient is proportional to (where, D = molecular diffusivity). (A) D (B) D2 (C) D0.5 (D) 1/D

Description : According to the film theory of mass transfer, the mass transfer co￾efficient is proportional to (where, D = molecular diffusivity). (A) D (B) D2 (C) D0.5 (D) 1/D

Last Answer : (A) D

. In a shell and tube heat exchanger, the tube side heat transfer co￾efficient just at the entrance of the tube is (A) Infinity (B) Zero (C) Same as average heat transfer co-efficient for tube side (D) None of these

Description : . In a shell and tube heat exchanger, the tube side heat transfer co￾efficient just at the entrance of the tube is (A) Infinity (B) Zero (C) Same as average heat transfer co-efficient for tube side (D) None of these

Last Answer : (A) Infinity

A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Description : A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Last Answer : (B) d -0.2

The rate of heat transfer is a product of overall heat transfer co￾efficient, the difference in temperature and the (A) Heating volume (B) Heat transfer area (C) Nusselt number (D) None of these

Description : The rate of heat transfer is a product of overall heat transfer co￾efficient, the difference in temperature and the (A) Heating volume (B) Heat transfer area (C) Nusselt number (D) None of these

Last Answer : (B) Heat transfer area

A single pass air heater is connected to a two pass unit. For the air flow rate and other conditions remaining the same, the film heat transfer co￾efficient for air will vary in the ratio of (A) 2 (B) 2 0.8 (C) 2 0.2 (D) 2 0.5

Description : A single pass air heater is connected to a two pass unit. For the air flow rate and other conditions remaining the same, the film heat transfer co￾efficient for air will vary in the ratio of (A) 2 (B) 2 0.8 (C) 2 0.2 (D) 2 0.5

Last Answer : (B) 2 0.8

The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2.K. The fouling factor after one year ofoperation is found to be hd0 = 2000 W/m2.K. The overall heat transfer co￾efficient at this time is(A) 1200 W/m2.K(B) 894 W/m2.K(C) 333 W/m2.K(D) 287 W/m2.K

Description : The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2 .K. The fouling factor after one year of operation is found to be hd0 = 2000 W/m2 .K. The overall heat transfer co￾efficient ... 1200 W/m2 .K (B) 894 W/m2 .K (C) 333 W/m2 .K (D) 287 W/m2 .K

Last Answer : (C) 333 W/m2 .K

All analogy equations connecting friction factor and heat transfer co￾efficient apply only to (A) Wall or skin friction (B) Form friction (C) Both (A) and (B) (D) Turbulent flow

Description : All analogy equations connecting friction factor and heat transfer co￾efficient apply only to (A) Wall or skin friction (B) Form friction (C) Both (A) and (B) (D) Turbulent flow

Last Answer : (A) Wall or skin friction

For motion of spherical particles in a stationary fluid, the drag co￾efficient in hindered settling compared to that in free settling is (A) More (B) Less (C) Equal (D) More or less, depending on the type of particle

Description : For motion of spherical particles in a stationary fluid, the drag co￾efficient in hindered settling compared to that in free settling is (A) More (B) Less (C) Equal (D) More or less, depending on the type of particle

Last Answer : (A) More

Lung cancer & DNA breakage are the major ill effects of excessive ozone exposure to human beings. Ozone layer depletion in the atmosphere is mainly caused by the presence of (A) CO2 (B) SO2 (C) Hydrocarbons (D) CFC (chloro fluoro carbon)

Description : Lung cancer & DNA breakage are the major ill effects of excessive ozone exposure to human beings. Ozone layer depletion in the atmosphere is mainly caused by the presence of (A) CO2 (B) SO2 (C) Hydrocarbons (D) CFC (chloro fluoro carbon)

Last Answer : (D) CFC (chloro fluoro carbon)

Due to which of the following reasons the cables should not be operated too hot ? (a) The oil may loose its viscosity and it may start drawing off from higher levels (b) Expansion of the oil may cause the sheath to burst (c) Unequal expansion may create voids in the insulation which will lead to ionization (d) The thermal instability may rise due to the rapid increase of dielectric losses with temperature (e) All of the above

Description : Due to which of the following reasons the cables should not be operated too hot ? (a) The oil may loose its viscosity and it may start drawing off from higher levels (b) Expansion of the ... instability may rise due to the rapid increase of dielectric losses with temperature (e) All of the above

Last Answer : (e) All of the above

Thermoplastic resins usually(A) Remain hard as long as they are hot(B) Cannot be reclaimed from waste(C) Permanent setting resins(D) Less brittle than thermosetting resins

Description : Thermoplastic resins usually (A) Remain hard as long as they are hot (B) Cannot be reclaimed from waste (C) Permanent setting resins (D) Less brittle than thermosetting resins

Last Answer : (D) Less brittle than thermosetting resins

Tempering of steel is done to make it (A) Brittle (B) Hard (C) Rollable (D) Soft

Description : Tempering of steel is done to make it (A) Brittle (B) Hard (C) Rollable (D) Soft

Last Answer : (D) Soft

Tempering of steel is done to make it (A) Brittle (B) Hard (C) Rollable (D) Soft

Description : Tempering of steel is done to make it (A) Brittle (B) Hard (C) Rollable (D) Soft

Last Answer : (D) Soft

A dense structure of grinding wheel is not used for the (A) Ductile material (B) Hard materials (C) Brittle materials (D) Finishing cuts

Description : A dense structure of grinding wheel is not used for the (A) Ductile material (B) Hard materials (C) Brittle materials (D) Finishing cuts

Last Answer : A) Ductile material

Cast iron is (A) Used for making shock resisting parts (B) Manufactured in cupola and is brittle (C) Having compressive strength more than its tensile strength(D) All (A), (B) & (C)

Description : Cast iron is (A) Used for making shock resisting parts (B) Manufactured in cupola and is brittle (C) Having compressive strength more than its tensile strength (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)