For motion of spherical particles in a stationary fluid, the drag co￾efficient in hindered settling compared to that in free settling is (A) More (B) Less (C) Equal (D) More or less, depending on the type of particle

For motion of spherical particles in a stationary fluid, the drag co￾efficient in hindered settling compared to that in free settling is
(A) More
(B) Less
(C) Equal
(D) More or less, depending on the type of particle
by

1 Answer

Answer :

(A) More
by

Related questions

In Newton's law range, the drag co-efficient for the motion of spherical particle in a stationary fluid is (A) 0.44 (B) 0.044 (C) 4.4 (D) 44

Description : In Newton's law range, the drag co-efficient for the motion of spherical particle in a stationary fluid is (A) 0.44 (B) 0.044 (C) 4.4 (D) 44

Last Answer : (A) 0.44

The ratio of the wall drag to the form drag in the Stoke's law range (for motion of spherical particles in a stationary fluid) is (A) 0.5 (B) 1 (C) 2 (D) 0.33

Description : The ratio of the wall drag to the form drag in the Stoke's law range (for motion of spherical particles in a stationary fluid) is (A) 0.5 (B) 1 (C) 2 (D) 0.33

Last Answer : (C) 2

Drag co-efficient for motion of spherical particles in a stationary fluid in the stoke's law range is (A) 24/NRe,P (B) 16/NRe,P (C) 64/NRe,P (D) 48/NRe,P

Description : Drag co-efficient for motion of spherical particles in a stationary fluid in the stoke's law range is (A) 24/NRe,P (B) 16/NRe,P (C) 64/NRe,P (D) 48/NRe,P

Last Answer : (A) 24/NRe,P

Drag co-efficient in hindered settling is __________ that in free settling. (A) Less than (B) Equal to (C) Not necessarily greater than (D) Always greater than

Description : Drag co-efficient in hindered settling is __________ that in free settling. (A) Less than (B) Equal to (C) Not necessarily greater than (D) Always greater than

Last Answer : (D) Always greater than

A 30% (by volume) suspension of spherical sand particles in a viscous oil has a hindered settling velocity of 4.44 μm/s. If the Richardson Zaki hindered settling index is 4.5, then the terminal velocity of a sand grain is (A) 0.90 μm/s (B) 1 μm/s (C) 22.1 μm/s (D) 0.02 μm/s

Description : A 30% (by volume) suspension of spherical sand particles in a viscous oil has a hindered settling velocity of 4.44 μm/s. If the Richardson Zaki hindered settling index is 4.5, then the terminal velocity of a sand grain is (A) 0.90 μm/s (B) 1 μm/s (C) 22.1 μm/s (D) 0.02 μm/s

Last Answer : (B) 1 μm/s

For the free settling of a spherical particle through a fluid, the slope of, CD-log NRe , plot is (A) 1(B) -1 (C) 0.5 (D) -0.5

Description : For the free settling of a spherical particle through a fluid, the slope of, CD-log NRe , plot is (A) 1 (B) -1 (C) 0.5 (D) -0.5

Last Answer : (B) -1

Forces acting on a particle settling in fluid are __________ forces. (A) Gravitational & buoyant (B) Centrifugal & drag (C) Gravitational or centrifugal buoyant drag (D) External, drag & viscous

Description : Forces acting on a particle settling in fluid are __________ forces. (A) Gravitational & buoyant (B) Centrifugal & drag (C) Gravitational or centrifugal buoyant drag (D) External, drag & viscous

Last Answer : (C) Gravitational or centrifugal buoyant drag

In hindered settling, the particles are (A) Placed farther from the wall (B) Not affected by other particles and the wall (C) Near each other (D) None of these

Description : In hindered settling, the particles are (A) Placed farther from the wall (B) Not affected by other particles and the wall (C) Near each other (D) None of these

Last Answer : (C) Near each othe

__________ forces act on a particle moving through a stationary fluid(A) Gravity(B) Drag(C) Buoyant(D) All (A), (B), & (C)

Description : __________ forces act on a particle moving through a stationary fluid (A) Gravity (B) Drag (C) Buoyant (D) All (A), (B), & (C)

Last Answer : (D) All (A), (B), & (C)

In Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass varies as the __________ of its diameter. (A) Inverse (B) Square root (C) Second power (D) First power

Description : In Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass varies as the __________ of its diameter. (A) Inverse (B) Square root (C) Second power (D) First power

Last Answer : (B) Square root

In the Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass is __________ the fluid viscosity. (A) Directly proportional to (B) Inversely proportional to (C) Inversely proportional to the square root of (D) Independent of

Description : In the Newton's law range, the terminal velocity of a solid spherical particle falling through a stationary fluid mass is __________ the fluid viscosity. (A) Directly proportional to (B) Inversely proportional to (C) Inversely proportional to the square root of (D) Independent of

Last Answer : (B) Inversely proportional to

The terminal velocity of a solid spherical particle falling through a stationary fluid mass in the Stoke's law range is proportional to the (A) Inverse of fluid viscosity (B) Square of particle size (C) Difference in the densities of the particle & fluid (D) All (A), (B) and (C)

Description : The terminal velocity of a solid spherical particle falling through a stationary fluid mass in the Stoke's law range is proportional to the (A) Inverse of fluid viscosity (B) Square of particle size (C) Difference in the densities of the particle & fluid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A spherical particle is falling slow in a viscous liquid such that Reynolds number is less than 1. Which statement is correct for this situation? (A) Inertial and drag forces are important (B) Drag, gravitational and buoyancy forces are important (C) Drag force and gravitational forces are important (D) None of the above

Description : A spherical particle is falling slow in a viscous liquid such that Reynolds number is less than 1. Which statement is correct for this situation? (A) Inertial and drag forces are important (B) Drag ... forces are important (C) Drag force and gravitational forces are important (D) None of the above

Last Answer : (B) Drag, gravitational and buoyancy forces are important

The settling velocity of a spherical particle of diameter less than 0.1 mm as per Stock’s law, is A. Vs = 418 (Gs – Gw) d [(3T + 70)/100] B. Vs = 418 (Gs – Gw)d² [(3T + 70)/100] C. Vs = 218 (Gs – Gw)d² [(3T + 70)/100] D. Vs = 218 (Gs – Gw)d [(3T + 70)/100]

Description : The settling velocity of a spherical particle of diameter less than 0.1 mm as per Stock’s law, is A. Vs = 418 (Gs – Gw) d [(3T + 70)/100] B. Vs = 418 (Gs – Gw)d² [(3T + 70)/100] C. Vs = 218 (Gs – Gw)d² [(3T + 70)/100] D. Vs = 218 (Gs – Gw)d [(3T + 70)/100]

Last Answer : ANS: B

For a particle settling in water at its terminal settling velocity, which of the following is true? (A) Buoyancy = weight + drag (B) Weight = buoyancy + drag (C) Drag = buoyancy + weight (D) Drag = weight

Description : For a particle settling in water at its terminal settling velocity, which of the following is true? (A) Buoyancy = weight + drag (B) Weight = buoyancy + drag (C) Drag = buoyancy + weight (D) Drag = weight

Last Answer : (B) Weight = buoyancy + drag

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below : Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, the minimum fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle ... fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s

Last Answer : (B) 16 mm/s

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below: Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, in actual operation, the above bed has a height = 1 m. What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system ... What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Last Answer : (C) 0.7

A suspension of glass beads in ethylene glycol has a hindered settling velocity of 1.7 mm/s, while the terminal settling velocity of a single glass bead in ethylene glycol is 17 mm/s. If the Richardson-Zaki hindered settling index is 4.5, the volume fraction of solids in the suspension is (A) 0.1 (B) 0.4 (C) 0.6 (D) None of these

Description : A suspension of glass beads in ethylene glycol has a hindered settling velocity of 1.7 mm/s, while the terminal settling velocity of a single glass bead in ethylene glycol is 17 mm/s. If the Richardson-Zaki hindered settling index ... in the suspension is (A) 0.1 (B) 0.4 (C) 0.6 (D) None of these

Last Answer : (C) 0.6

Two particles are called to be equal settling, if they are having the same. (A) Size (B) Specific gravity (C) Terminal velocities in the same fluid & in the same field of force (D) None of these

Description : Two particles are called to be equal settling, if they are having the same. (A) Size (B) Specific gravity (C) Terminal velocities in the same fluid & in the same field of force (D) None of these

Last Answer : (C) Terminal velocities in the same fluid & in the same field of force

In classification, particles are said to be equal settling, if they have the same terminal velocities in the (A) Different fluids (B) Same fluid (C) Same field of force (D) Both (B) and (C)

Description : In classification, particles are said to be equal settling, if they have the same terminal velocities in the (A) Different fluids (B) Same fluid (C) Same field of force (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Sorting classifiers employing differential settling methods forseparation of particles make use of the differences in their(A) Particle sizes(B) Densities(C) Terminal velocities(D) None of these

Description : Sorting classifiers employing differential settling methods forseparation of particles make use of the differences in their (A) Particle sizes (B) Densities (C) Terminal velocities (D) None of these

Last Answer : (C) Terminal velocities

Brownian movement is prominent in the particle size range of __________ microns in case of settling of a particle in a fluid. (A) 2 to 3 (B) 0.01 to 0.10 (C) 200 to 300 (D) 100 to 1000

Description : Brownian movement is prominent in the particle size range of __________ microns in case of settling of a particle in a fluid. (A) 2 to 3 (B) 0.01 to 0.10 (C) 200 to 300 (D) 100 to 1000

Last Answer : A) 2 to 3

Which of the following is not concerned with the fluid-particle interaction? (A) Drag co-efficient (B) Froude number (C) Galileo number (D) Weber number

Description : Which of the following is not concerned with the fluid-particle interaction? (A) Drag co-efficient (B) Froude number (C) Galileo number (D) Weber number

Last Answer : (D) Weber number

. In case of turbulent flow of fluid through a circular pipe, the (A) Mean flow velocity is about 0.5 times the maximum velocity (B) Velocity profile becomes flatter and flatter with increasing Reynolds number (C) Point of maximum instability exists at a distance of 2r/3 from the pipe wall (r = pipe radius) (D) Skin friction drag, shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

Description : . In case of turbulent flow of fluid through a circular pipe, the (A) Mean flow velocity is about 0.5 times the maximum velocity (B) Velocity profile becomes flatter and flatter with ... , shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

Last Answer : (D) Skin friction drag, shear stresses, random orientation of fluid particles and slope of velocity profile at the wall are more

The specific surface of spherical particles is given by (where D and ρ are diameter and density of particle). (A) 6/D.ρ(B) 2/D.ρ (C) 4/D.ρ (D) 12/D.ρ

Description : The specific surface of spherical particles is given by (where D and ρ are diameter and density of particle). (A) 6/D.ρ (B) 2/D.ρ (C) 4/D.ρ (D) 12/D.ρ

Last Answer : (A) 6/D.ρ

The specific surface of spherical particles is proportional to (where, Dp = diameter of particle). (A) D2 p (B) Dp (C) 1/Dp (D) 1/D2p

Description : The specific surface of spherical particles is proportional to (where, Dp = diameter of particle). (A) D2 p (B) Dp (C) 1/Dp (D) 1/D2p

Last Answer : (C) 1/Dp

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

In case of parallel flow heat exchanger, the lowest temperature theoretically attainable by the hot fluid is __________ the outlet temperature of the cold fluid. (A) Equal to (B) More than (C) Less than (D) Either more or less than (depending upon the fluid)

Description : In case of parallel flow heat exchanger, the lowest temperature theoretically attainable by the hot fluid is __________ the outlet temperature of the cold fluid. (A) Equal to (B) More than (C) Less than (D) Either more or less than (depending upon the fluid)

Last Answer : (A) Equal to

A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Description : A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Last Answer : (B) d -0.2

A particle is settling in a liquid under Stokesian conditions. The free falling velocity of the particle is proportional to (A) √(Particle diameter) (B) Particle diameter (C) (Particle diameter)2 (D) (Particle diameter)3

Description : A particle is settling in a liquid under Stokesian conditions. The free falling velocity of the particle is proportional to (A) √(Particle diameter) (B) Particle diameter (C) (Particle diameter)2 (D) (Particle diameter)3

Last Answer : B) Particle diameter

Which of the following is not an advantage of fluidisation from transferoperation point of view?(A) Intimate contact of the fluid with all parts of the solid particles(B) Lower fluid pumping power requirement(C) Minimisation of temperature variation(D) Prevention of particle segregation

Description : Which of the following is not an advantage of fluidisation from transferoperation point of view? (A) Intimate contact of the fluid with all parts of the solid particles (B) Lower fluid pumping power requirement (C) Minimisation of temperature variation (D) Prevention of particle segregation

Last Answer : (B) Lower fluid pumping power requirement

A streamline is a line in flow field, (A) That is traced by all the fluid particles passing through a given point (B) Along which a fluid particle travels (C) Such that at every point on it, the velocity is tangential to it (D) None of these

Description : A streamline is a line in flow field, (A) That is traced by all the fluid particles passing through a given point (B) Along which a fluid particle travels (C) Such that at every point on it, the velocity is tangential to it (D) None of these

Last Answer : (C) Such that at every point on it, the velocity is tangential to it

For the non catalytic reaction of particles with surrounding fluid, the same needed to achieve the same fractional conversion for particles of different unchanging sizes is proportional to the particle diameter, when the __________ is the controlling resistance. (A) Film diffusion (B) Diffusion through ash layer (C) Chemical reaction (D) Either (A), (B) or (C)

Description : For the non catalytic reaction of particles with surrounding fluid, the same needed to achieve the same fractional conversion for particles of different unchanging sizes is proportional to the particle diameter, when the ... through ash layer (C) Chemical reaction (D) Either (A), (B) or (C)

Last Answer : (C) Chemical reaction

For the non-catalytic reaction of particles with surrounding fluid, the time needed to achieve the same fractional conversion for particles of different but unchanging sizes is proportional to the square of particle diameter, when the __________ is the controlling resistance. (A) Film diffusion (B) Diffusion through ash layer (C) Chemical reaction (D) Either (A), (B) or (C)

Description : For the non-catalytic reaction of particles with surrounding fluid, the time needed to achieve the same fractional conversion for particles of different but unchanging sizes is proportional to the square of particle diameter, ... through ash layer (C) Chemical reaction (D) Either (A), (B) or (C)

Last Answer : (B) Diffusion through ash layer

For a non-spherical particle, the sphericity (A) Is defined as the ratio of surface area of a sphere having the same volume as the particle to the actual surface area of the particle (B) Has the dimension of length (C) Is always less than 1 (D) Is the ratio of volume of a sphere having the same surface area as the particle to the actual volume of the particle

Description : For a non-spherical particle, the sphericity (A) Is defined as the ratio of surface area of a sphere having the same volume as the particle to the actual surface area of the particle (B) Has ... of volume of a sphere having the same surface area as the particle to the actual volume of the particle

Last Answer : (A) Is defined as the ratio of surface area of a sphere having the same volume as the particle to the actual surface area of the particle

Can you easily face another 30-40(more depending on your age)years of life without feeling overwhelmed and depressed at days that just drag on?

Description : Can you easily face another 30-40(more depending on your age)years of life without feeling overwhelmed and depressed at days that just drag on?

Last Answer : answer:I was doing fine until I saw your question and really thought about it.~ I'm sorry that you're fighting despair, especially if that's a full-time thing. But maybe part of the thing is, as ... (I'm not trying to make light of your feeling, but there must be something keeping you busy, right?)

At triple point (for one component system), vapour pressure of solid as compared to that of liquid will be (A) More (B) Less (C) Same (D) More or less; depending on the system

Description : At triple point (for one component system), vapour pressure of solid as compared to that of liquid will be (A) More (B) Less (C) Same (D) More or less; depending on the system

Last Answer : (C) Same

The work done in isothermal compression compared to that in adiabatic compression will be (A) Less (B) More (C) Same (D) More or less depending upon the extent of work done

Description : The work done in isothermal compression compared to that in adiabatic compression will be (A) Less (B) More (C) Same (D) More or less depending upon the extent of work done

Last Answer : (B) More

Particle size range in which dust catcher (gravity settling chamber) works most effectively and efficiently is __________ microns. (A) < 5 (B) 10 to 25 (C) < 74 (D) > 1000

Description : Particle size range in which dust catcher (gravity settling chamber) works most effectively and efficiently is __________ microns. (A) < 5 (B) 10 to 25 (C) < 74 (D) > 1000

Last Answer : (C) < 74

A particle A of diameter 10 microns settles in an oil of specific gravity 0.9 and viscosity 10 poise under Stoke's law. A particle B with diameter 20microns settling in the same oil will have a settling velocity (A) Same as that of A (B) One fourth as that of A (C) Twice as that of A (D) Four times as that of A

Description : A particle A of diameter 10 microns settles in an oil of specific gravity 0.9 and viscosity 10 poise under Stoke's law. A particle B with diameter 20microns settling in the same oil will have a settling velocity (A) ... ) One fourth as that of A (C) Twice as that of A (D) Four times as that of A

Last Answer : (B) One fourth as that of A

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

What is the force required (in Newtons) to hold a spherical balloon stationary in water at a depth of H from the air-water interface? The balloon is of radius 0.1 m and is filled with air. (A) 4πg/3 (B) 0.01 πgH/4(C) 0.01 πgH/8 (D) 0.04 πgH/3

Description : What is the force required (in Newtons) to hold a spherical balloon stationary in water at a depth of H from the air-water interface? The balloon is of radius 0.1 m and is filled with air. (A) 4πg/3 (B) 0.01 πgH/4 (C) 0.01 πgH/8 (D) 0.04 πgH/3

Last Answer : (A) 4πg/3

The most efficient equipment for the removal of sub-micronic dust particles from blast furnace gas is the (A) Venturi atomiser (B) Gravity settling chamber (C) Electro-static precipitator (D) Cyclone separator

Description : The most efficient equipment for the removal of sub-micronic dust particles from blast furnace gas is the (A) Venturi atomiser (B) Gravity settling chamber (C) Electro-static precipitator (D) Cyclone separator

Last Answer : (C) Electro-static precipitator

Which is the most efficient dust removal equipment for removal of submicronic dust particles from blast furnace gas? (A) Packed scrubber (B) Gravity settling chamber (C) Electrostatic precipitator (D) Hydrocyclone

Description : Which is the most efficient dust removal equipment for removal of submicronic dust particles from blast furnace gas? (A) Packed scrubber (B) Gravity settling chamber (C) Electrostatic precipitator (D) Hydrocyclone

Last Answer : (C) Electrostatic precipitator

A charged particle is moving in a UNIFORM magnetic field. If the direction of motion of the charged particle is at right angles to the magnetic field, describe the shape of the charged particle's path.

Description : A charged particle is moving in a UNIFORM magnetic field. If the direction of motion of the charged particle is at right angles to the magnetic field, describe the shape of the charged particle's path.

Last Answer : ANSWER: CIRCULAR or CIRCLE

A charged particle is moving in a UNIFORM magnetic field. If the direction of motion of the charged particle is parallel to the magnetic field, describe the shape of the charged particle's path.

Description : A charged particle is moving in a UNIFORM magnetic field. If the direction of motion of the charged particle is parallel to the magnetic field, describe the shape of the charged particle's path. 

Last Answer : ANSWER: STRAIGHT LINE

For the same terminal conditions and valve size, the pressure drop in a fully opened globe valve as compared to that in a gate valve is (A) More (B) Less (C) Equal (D) Either (A) or (B); depends on the viscosity of the fluid

Description : For the same terminal conditions and valve size, the pressure drop in a fully opened globe valve as compared to that in a gate valve is (A) More (B) Less (C) Equal (D) Either (A) or (B); depends on the viscosity of the fluid

Last Answer : (A) More

Select the wrong statement pertaining to flow of an incompressible fluid through a Venturimeter. (A) For frictionless flow, the fluid pressure entering the venturi meter will be exactly equal to that leaving the Venturimeter(B) Discharge of fluid through a Venturimeter depends upon the gagedifference irrespective of the orientation of Venturimeter(C) Venturimeter occupies less space than an orificemeter(D) Venturimeter incurs less power loss compared to an equivalentorificemeter

Description : Select the wrong statement pertaining to flow of an incompressible fluid through a Venturimeter. (A) For frictionless flow, the fluid pressure entering the venturi meter will be exactly equal ... than an orificemeter (D) Venturimeter incurs less power loss compared to an equivalent orificemeter

Last Answer : (C) Venturimeter occupies less space than an orificemeter

The terminal velocity of a small sphere settling in a viscous fluid varies as the (A) First power of its diameter (B) Inverse of the fluid viscosity (C) Inverse square of the diameter (D) Square of the difference in specific weights of solid & fluid

Description : The terminal velocity of a small sphere settling in a viscous fluid varies as the (A) First power of its diameter (B) Inverse of the fluid viscosity (C) Inverse square of the diameter (D) Square of the difference in specific weights of solid & fluid

Last Answer : (B) Inverse of the fluid viscosity

The refrigeration effect in a dry evaporator compared to flooded evaporator in a similar plant is (a) same (b) more (c) less (d) more or less depending on ambient conditions

Description : The refrigeration effect in a dry evaporator compared to flooded evaporator in a similar plant is (a) same (b) more (c) less (d) more or less depending on ambient conditions

Last Answer : Ans: c