Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal
(A) Tensile strength
(B) Compressive strength
(C) Young's modulus
(D) Thermal co-efficient of expansion
by

1 Answer

Answer :

(D) Thermal co-efficient of expansion
by

Related questions

Pick out the wrong statement pertaining to the properties of glasses. Glasses generally have (A) High electrical insulation properties (B) Sharp melting points (C) Low co-efficient of thermal expansion (D) Compressive strength much greater than their tensile strengths

Description : Pick out the wrong statement pertaining to the properties of glasses. Glasses generally have (A) High electrical insulation properties (B) Sharp melting points (C) Low co-efficient of thermal expansion (D) Compressive strength much greater than their tensile strengths

Last Answer : (B) Sharp melting points

Steel rods are used in reinforced concrete to increase its __________ strength. (A) Shear (B) Tensile (C) Compressive (D) None of these

Description : Steel rods are used in reinforced concrete to increase its __________ strength. (A) Shear (B) Tensile (C) Compressive (D) None of these

Last Answer : (B) Tensile

Modulus of rupture of concrete is a measure of (A) Flexural tensile strength (B) Direct tensile strength (C) Compressive strength (D) Split tensile strength

Description : Modulus of rupture of concrete is a measure of (A) Flexural tensile strength (B) Direct tensile strength (C) Compressive strength (D) Split tensile strength

Last Answer : Answer: Option A

The moment of resistance of an over-reinforcement section is determined on the basis of (a) Compressive force developed in concrete (b) Tensile force developed in steel (c) Both (a) & (b) (d) None of these

Description : The moment of resistance of an over-reinforcement section is determined on the basis of (a) Compressive force developed in concrete (b) Tensile force developed in steel (c) Both (a) & (b) (d) None of these

Last Answer : (a) Compressive force developed in concrete

Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Description : Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Last Answer : (A) Modulus of elasticity (young's modulus)

Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Last Answer : (D) Endurance limit

Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Description : Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Last Answer : Option A

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

A rod 3 m long is heated from 10°C to 90°C. Find the expansion of rod. Take Young’s modulus = 1.0 x 10^5 MN/m2 and coefficient of thermal expansion = 0.000012 per degree centigrade. 1. 0.168 cm 2. 0.208 cm 3. 0.288 cm 4. 0.348 cm

Description : A rod 3 m long is heated from 10°C to 90°C. Find the expansion of rod. Take Young’s modulus = 1.0 x 10^5 MN/m2 and coefficient of thermal expansion = 0.000012 per degree centigrade. 1. 0.168 cm 2. 0.208 cm 3. 0.288 cm 4. 0.348 cm

Last Answer : 3. 0.288 cm

Normally, the tensile strength of concrete is about____________of its compressive strength (a) 10 to 15% (b) 15 to 20% (c) 20 to 25% (d) 25 to 30%

Description : Normally, the tensile strength of concrete is about____________of its compressive strength (a) 10 to 15% (b) 15 to 20% (c) 20 to 25% (d) 25 to 30%

Last Answer : (a) 10 to 15%

A higher modular ratio shows (A) Higher compressive strength of concrete (B) Lower compressive strength of concrete (C) Higher tensile strength of steel (D) Lower tensile strength of steel

Description : A higher modular ratio shows (A) Higher compressive strength of concrete (B) Lower compressive strength of concrete (C) Higher tensile strength of steel (D) Lower tensile strength of steel

Last Answer : Answer: Option B

The purpose of reinforcement in pre-stressed concrete is (A) To provide adequate bond stress (B) To resist tensile stresses (C) To impart initial compressive stress in concrete (D) All of the above

Description : The purpose of reinforcement in pre-stressed concrete is (A) To provide adequate bond stress (B) To resist tensile stresses (C) To impart initial compressive stress in concrete (D) All of the above

Last Answer : Answer: Option C

If C is creep coefficient, f is original pre-stress in concrete, m is modular ratio, E is Young's modulus of steel and e is shrinkage strain, the combined effect of creep and shrinkage is: (A) (1 - C)mf - eEB) (C - 1)mf + eE(C) (C - 1)mf - eE(D) (1 - C)mf + eE

Description : If C is creep coefficient, f is original pre-stress in concrete, m is modular ratio, E is Young's modulus of steel and e is shrinkage strain, the combined effect of creep and shrinkage is: (A) (1 - C)mf - eE B) (C - 1)mf + eE (C) (C - 1)mf - eE (D) (1 - C)mf + eE

Last Answer : Answer: Option B

The modular ratio is the ration of (a) Young’s modulus of steel to the young’s modulus of concrete (b) Young’s modules of concrete to the young’s modulus of steel (c) Load carried by steel to the load carried by concrete. (d) Load carried by concrete to the load carried by step.

Description : The modular ratio is the ration of (a) Young’s modulus of steel to the young’s modulus of concrete (b) Young’s modules of concrete to the young’s modulus of steel (c) Load carried by steel to the load carried by concrete. (d) Load carried by concrete to the load carried by step.

Last Answer : (c) Load carried by steel to the load carried by concrete.

High copper amalgam lasts longer than low copper amalgam because of:** A. Increased compressive strength B. Increased corrosion resistance C. High creep D. Increased tensile strength E. Decreased setting expansion

Description : High copper amalgam lasts longer than low copper amalgam because of:**  A. Increased compressive strength  B. Increased corrosion resistance  C. High creep  D. Increased tensile strength  E. Decreased setting expansion 

Last Answer : A. Increased compressive strength 

In singly reinforced beams, steel reinforcement is provided in (a) Compressive zone (b) Tensile zone (c) Neutral zone (d) All the above

Description : In singly reinforced beams, steel reinforcement is provided in (a) Compressive zone (b) Tensile zone (c) Neutral zone (d) All the above

Last Answer : (b) Tensile zone

Between 230 and 370°C, blue brittleness is caused in mild steel because of the (A) Immobility of dislocation (B) Strain-ageing (C) Increase in Young's modulus (D) Strain hardening

Description : Between 230 and 370°C, blue brittleness is caused in mild steel because of the (A) Immobility of dislocation (B) Strain-ageing (C) Increase in Young's modulus (D) Strain hardening

Last Answer : Option B

Young's modulus is defined as A. tensile strain/tensile stress B. tensile stress/tensile strain C. tensile stress × tensile strain D. length/area

Description : Young's modulus is defined as A. tensile strain/tensile stress B. tensile stress/tensile strain C. tensile stress × tensile strain D. length/area

Last Answer : tensile stress/tensile strain

Ratio of tensile to strain is A. Young's modulus B. stress C. stiffness D. tensile force

Description : Ratio of tensile to strain is A. Young's modulus B. stress C. stiffness D. tensile force

Last Answer : Young's modulus

Young’s Modulus of elasticity is (a)Tensile stress / Tensile strain (b)Shear stress / Shear strain (c)Tensile stress / Shear strain (d)Shear stress / Tensile strain

Description : Young’s Modulus of elasticity is (a)Tensile stress / Tensile strain (b)Shear stress / Shear strain (c)Tensile stress / Shear strain (d)Shear stress / Tensile strain

Last Answer : a)Tensile stress / Tensile strain

Brass tubes are used in the manufacture of tubes of evaporators used in sugar and salt industries, mainly because of its (A) High co-efficient of thermal expansion (B) Low thermal conductivity (C) High corrosion resistance (D) All (A), (B) and (C)

Description : Brass tubes are used in the manufacture of tubes of evaporators used in sugar and salt industries, mainly because of its (A) High co-efficient of thermal expansion (B) Low thermal conductivity (C) High corrosion resistance (D) All (A), (B) and (C)

Last Answer : (C) High corrosion resistance

Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Description : Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Last Answer : (C) Machinability

The application of elastic theory to the beams is based on the assumption that (a) At any cross-section, plane sections before bending remain plane after bending (b) All tensile stresses are taken up by reinforcement alone and none by the concrete. (c) Steel reinforcement is free from initial stresses when it is embedded in concrete. (d) All of the above

Description : The application of elastic theory to the beams is based on the assumption that (a) At any cross-section, plane sections before bending remain plane after bending (b) All tensile stresses are taken ... reinforcement is free from initial stresses when it is embedded in concrete. (d) All of the above

Last Answer : (d) All of the above

In the reinforced cement concrete structure, the steel reinforcement consists of . (a) Deformed bars (b) Cold twisted bars (c) Mildsteel and medium tensile steel bars (d) All of these

Description : In the reinforced cement concrete structure, the steel reinforcement consists of . (a) Deformed bars (b) Cold twisted bars (c) Mildsteel and medium tensile steel bars (d) All of these

Last Answer : (d) All of these

Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Last Answer : (A) Consistency

Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Last Answer : (A) Consistency

Allowable shear strength of concrete, depends upon (A) Shear strength (B) Tensile strength (C) Compressive strength (D) None of these

Description : Allowable shear strength of concrete, depends upon (A) Shear strength (B) Tensile strength (C) Compressive strength (D) None of these

Last Answer : Answer: Option A

The tensile strength of concrete is about ________ of its compressive strength [ A ] 10% to 15% [ B ] 30% to 40% [ C ] 50% [ D ] 60% to 75%

Description : The tensile strength of concrete is about ________ of its compressive strength [ A ] 10% to 15% [ B ] 30% to 40% [ C ] 50% [ D ] 60% to 75%

Last Answer : [ A ] 10% to 15%

Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value

Description : Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value

Last Answer : [ A ] Consistency

The diameter of transverse reinforcement of columns should be equal to one-fourth of the diameter of the main steel rods but not less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 7 mm

Description : The diameter of transverse reinforcement of columns should be equal to one-fourth of the diameter of the main steel rods but not less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 7 mm

Last Answer : Answer: Option D

In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Description : In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Last Answer : Answer: Option D

The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these

Description : The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these

Last Answer : (a) Bond stress

The moment of resistance of an under- reinforced section is computer on the basis of (a) Compressive force developed in concrete (b) Tensile force developed in steel (c) Both (a) & (b) (d) All the above

Description : The moment of resistance of an under- reinforced section is computer on the basis of (a) Compressive force developed in concrete (b) Tensile force developed in steel (c) Both (a) & (b) (d) All the above

Last Answer : (b) Tensile force developed in steel

Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Description : Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Last Answer : Answer: Option D

The Young's modulus of elasticity of steel, is (A) 150 KN/mm2 (B) 200 KN/mm2 (C) 250 KN/mm2 (D) 275 KN/mm

Description : The Young's modulus of elasticity of steel, is (A) 150 KN/mm2 (B) 200 KN/mm2 (C) 250 KN/mm2 (D) 275 KN/mm

Last Answer : Answer: Option D

At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of the section by (A) Depth of the section (B) Depth of the neutral axis (C) Maximum tensile stress at the section (D) Maximum compressive stress at the section

Description : At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of  the section by  (A) Depth of the section  (B) Depth of the neutral axis  (C) Maximum tensile stress at the section  (D) Maximum compressive stress at the section

Last Answer : (B) Depth of the neutral axis 

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

Which of the following is an undesirable property of a manometricliquid? (A) Non-sticky & non-corrosive nature (B) High vapour pressure (C) Low viscosity & surface tension (D) Low co-efficient of thermal expansion

Description : Which of the following is an undesirable property of a manometricliquid? (A) Non-sticky & non-corrosive nature (B) High vapour pressure (C) Low viscosity & surface tension (D) Low co-efficient of thermal expansion

Last Answer : (B) High vapour pressure

Superior quality laboratory apparatus is made of the __________ glass having low thermal co-efficient of expansion & high chemical resistance. (A) Flint (B) Soda (C) Pyrex (D) Potash

Description : Superior quality laboratory apparatus is made of the __________ glass having low thermal co-efficient of expansion & high chemical resistance. (A) Flint (B) Soda (C) Pyrex (D) Potash

Last Answer : (C) Pyrex

Co-efficient of thermal expansion of glass is decreased by the addition of __________ during its manufacture. (A) CaO (B) MnO2 (C) ZnO (D) FeS

Description : Co-efficient of thermal expansion of glass is decreased by the addition of __________ during its manufacture. (A) CaO (B) MnO2 (C) ZnO (D) FeS

Last Answer : (C) ZnO

__________ glass has the lowest co-efficient of thermal expansion and hence is more heat resistant. (A) Pyrex (B) Soda lime (C) Lead (D) High silica

Description : __________ glass has the lowest co-efficient of thermal expansion and hence is more heat resistant. (A) Pyrex (B) Soda lime (C) Lead (D) High silica

Last Answer : (A) Pyrex

(1/V) (∂V/∂T)Pis the mathematical expression (A) Joule-Thomson co-efficient (B) Specific heat at constant pressure (Cp) (C) co-efficient of thermal expansion (D) Specific heat at constant volume (CV)

Description : (1/V) (∂V/∂T)Pis the mathematical expression (A) Joule-Thomson co-efficient (B) Specific heat at constant pressure (Cp) (C) co-efficient of thermal expansion (D) Specific heat at constant volume (CV)

Last Answer : (C) co-efficient of thermal expansion

The expression, nCv(T2- T1), is for the __________ of an ideal gas. (A) Work done under adiabatic condition (B) Co-efficient of thermal expansion (C) Compressibility (D) None of these

Description : The expression, nCv(T2- T1), is for the __________ of an ideal gas. (A) Work done under adiabatic condition (B) Co-efficient of thermal expansion (C) Compressibility (D) None of these

Last Answer : (A) Work done under adiabatic condition

The expression, nRT ln(P1/P2), is for the __________of an ideal gas. (A) Compressibility (B) Work done under adiabatic condition (C) Work done under isothermal condition (D) Co-efficient of thermal expansion

Description : The expression, nRT ln(P1/P2), is for the __________of an ideal gas. (A) Compressibility (B) Work done under adiabatic condition (C) Work done under isothermal condition (D) Co-efficient of thermal expansion

Last Answer : C) Work done under isothermal condition

If the average compressive strength is 4000 kg/cm2 and standard deviation is 500, the co-efficient of variation is (A) 10 % (B) 12.5 % (C) 15 % (D) 18.5%

Description : If the average compressive strength is 4000 kg/cm2 and standard deviation is 500, the co-efficient of variation is (A) 10 % (B) 12.5 % (C) 15 % (D) 18.5%

Last Answer : Answer: Option B

Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity of steel (4) Geometry of the section. Which of these statements are correct? (a) 2, 3 and 4 (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Description : Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity ... (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Last Answer : 1,2,4

Metallic surveying tapes are made of __________ which has a low co efficient of expansion & enough strength. (A) Invar (B) Hastelloy (C) Duralumin (D) Monel metal

Description : Metallic surveying tapes are made of __________ which has a low co efficient of expansion & enough strength. (A) Invar (B) Hastelloy (C) Duralumin (D) Monel metal

Last Answer : (A) Invar

The effectiveness factor for large value of Thiele modulus [L√(K/D1 )] of a solid catalysed first order reaction is equal to (where, L = length of the reactor, cm, D1 = diffusion co-efficient, cm2 /second). (A) L √(K/D1 ) (B) 1/[L√(K/D1 )] (C) 1 (D) ∞

Description : The effectiveness factor for large value of Thiele modulus [L√(K/D1 )] of a solid catalysed first order reaction is equal to (where, L = length of the reactor, cm, D1 = diffusion co-efficient, cm2 /second). (A) L √(K/D1 ) (B) 1/[L√(K/D1 )] (C) 1 (D) ∞

Last Answer : (B) 1/[L√(K/D1 )]

A composite beam is composed of two equal strips one of brass and other of steel. If the temperature is raised (A) Steel experiences tensile force (B) Brass experiences compressive force (C) Composite beam gets subjected to a couple (D) All the above

Description : A composite beam is composed of two equal strips one of brass and other of steel. If the  temperature is raised  (A) Steel experiences tensile force  (B) Brass experiences compressive force  (C) Composite beam gets subjected to a couple  (D) All the above

Last Answer : (D) All the above