Approximate value of the modulus of elasticity for steel is about __________ × 10 6kg/cm2 . (A) 0.5 (B) 2 (C) 40 (D) 75

Approximate value of the modulus of elasticity for steel is about
__________ × 10
6kg/cm2
.
(A) 0.5
(B) 2
(C) 40
(D) 75
by

1 Answer

Answer :

(B) 2
by

Related questions

A standard steel tape of length 30 m and cross-section 15 × 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of steel tape is 2.2 × 106 kg/cm2 , the correction to be applied is (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these

Description : A standard steel tape of length 30 m and cross-section 15 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of ... (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these

Last Answer : (A) - 0.000909 m

Which of the following has the highest modulus of elasticity (about 7 × 106 kg/cm2)? (A) High speed steel (B) Stainless steel (C) Tungsten carbide (D) Superalloys

Description : Which of the following has the highest modulus of elasticity (about 7 × 106 kg/cm2)? (A) High speed steel (B) Stainless steel (C) Tungsten carbide (D) Superalloys

Last Answer : (C) Tungsten carbide

Modulus of elasticity of steel as per IS: 4561978 shall be taken as (A) 20 kN/cm² (B) 200 kN/cm² (C) 200 kN/mm² (D) 2 × 106 N/cm2

Description : Modulus of elasticity of steel as per IS: 4561978 shall be taken as (A) 20 kN/cm² (B) 200 kN/cm² (C) 200 kN/mm² (D) 2 × 106 N/cm2

Last Answer : Answer: Option C

A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2 MN/mm2 and Poisson's ratio is 0.25, the change in the volume of the bar is: (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm

Description : A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2  MN/mm2  and Poisson's ratio is 0.25, the change in the volume of the bar is:  (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm

Last Answer : (C) 3.125 cm

If 20 kg of coarse aggregate is sieved through 80 mm, 40 mm, 20 mm, 10 mm, 4.75 mm, 2.36 mm, 1.18 mm, 600 micron, 300 micron and 150 micron standard sieves and the weights retained are 0 kg, 2 kg, 8 kg, 6 kg, 4 kg respectively, the fineness modulus of the aggregate, is (A) 7.30 (B) 7.35 (C) 7.40 (D) 7.45

Description : If 20 kg of coarse aggregate is sieved through 80 mm, 40 mm, 20 mm, 10 mm, 4.75 mm, 2.36 mm, 1.18 mm, 600 micron, 300 micron and 150 micron standard sieves and the weights retained are 0 kg, 2 kg, 8 kg, ... , the fineness modulus of the aggregate, is (A) 7.30 (B) 7.35 (C) 7.40 (D) 7.45

Last Answer : Answer: Option C

The Young's modulus of elasticity of steel, is (A) 150 KN/mm2 (B) 200 KN/mm2 (C) 250 KN/mm2 (D) 275 KN/mm

Description : The Young's modulus of elasticity of steel, is (A) 150 KN/mm2 (B) 200 KN/mm2 (C) 250 KN/mm2 (D) 275 KN/mm

Last Answer : Answer: Option D

Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity of steel (4) Geometry of the section. Which of these statements are correct? (a) 2, 3 and 4 (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Description : Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity ... (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Last Answer : 1,2,4

Modulus elasticity of steel is generally taken as [ A ] 2 x 105 N/mm2 [ B ] 2 x 106 N/mm2 [ C ] 2 x 106 N/mm2 [ D ] 2 x 105 N/mm2

Description : Modulus elasticity of steel is generally taken as [ A ] 2 x 105 N/mm2 [ B ] 2 x 106 N/mm2 [ C ] 2 x 106 N/mm2 [ D ] 2 x 105 N/mm2

Last Answer : [ A ] 2 x 105 N/mm2

Modulus elasticity of steel is generally taken as [ A ] 2 x 105 N/mm2 [ B ] 2 x 106 N/mm2 [ C ] 2 x 106 N/mm2 [ D ] 2 x 105 N/mm2

Description : Modulus elasticity of steel is generally taken as [ A ] 2 x 105 N/mm2 [ B ] 2 x 106 N/mm2 [ C ] 2 x 106 N/mm2 [ D ] 2 x 105 N/mm2

Last Answer : [ A ] 2 x 105 N/mm2

The effectiveness factor for large value of Thiele modulus [L√(K/D1 )] of a solid catalysed first order reaction is equal to (where, L = length of the reactor, cm, D1 = diffusion co-efficient, cm2 /second). (A) L √(K/D1 ) (B) 1/[L√(K/D1 )] (C) 1 (D) ∞

Description : The effectiveness factor for large value of Thiele modulus [L√(K/D1 )] of a solid catalysed first order reaction is equal to (where, L = length of the reactor, cm, D1 = diffusion co-efficient, cm2 /second). (A) L √(K/D1 ) (B) 1/[L√(K/D1 )] (C) 1 (D) ∞

Last Answer : (B) 1/[L√(K/D1 )]

A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2 , the deflection of the free end, is (A) 2 mm (B) 3 mm (C) 4 mm (D) 5 mm

Description : A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free  end. If the modulus of elasticity of the material is 0.2 × 106  N/mm2 , the deflection of the free end,  is  (A) 2 mm  (B) 3 mm  (C) 4 mm  (D) 5 mm

Last Answer : (D) 5 mm

For an incompressible fluid, the bulk modulus of elasticity is (A) 5 kg/m3 (B) ∞ N/m2 (C) 1 N (D) 0 N/m

Description : For an incompressible fluid, the bulk modulus of elasticity is (A) 5 kg/m3 (B) ∞ N/m2 (C) 1 N (D) 0 N/m

Last Answer : (B) ∞ N/m2

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

Which of the following is not a dimension-less group used in catalysis? (Where, D = dispersion co-efficient, cm2 /sec.D1 = diffusion co-efficient; cm2 /sec L = length of the reactor, cm t = time, sec, v = volumetric flow rate, cm3 /sec. V = volume, cm3 .) (A) Reactor dispersion number (D/vL) (B) Reduced time (vt/V) (C) Thiele modulus L √(k/D1 ) (D) None of these

Description : Which of the following is not a dimension-less group used in catalysis? (Where, D = dispersion co-efficient, cm2 /sec.D1 = diffusion co-efficient; cm2 /sec L = length of the reactor, cm t = time, sec, v = volumetric ... (D/vL) (B) Reduced time (vt/V) (C) Thiele modulus L √(k/D1 ) (D) None of these

Last Answer : (D) None of these

A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

A liquid compressed in cylinder has a volume of 0.04 m3 at 50 kg/cm² and a volume of 0.039 m3 at 150 kg/cm². The bulk modulus of elasticity of liquid is (A) 400 kg/cm² (B) 4000 kg/cm² (C) (D)

Description : A liquid compressed in cylinder has a volume of 0.04 m3 at 50 kg/cm² and a volume of 0.039 m3 at 150 kg/cm². The bulk modulus of elasticity of liquid is (A) 400 kg/cm² (B) 4000 kg/cm² (C) (D)

Last Answer : Answer: Option B

Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Description : Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Last Answer : (A) Modulus of elasticity (young's modulus)

The unit of bulk modulus of elasticity for a liquid in S.I. unit is (A) N (B) N/m (C) N/m2 (D) N/m3

Description : The unit of bulk modulus of elasticity for a liquid in S.I. unit is (A) N (B) N/m (C) N/m2 (D) N/m3

Last Answer : (C) N/m2

The bulk modulus of elasticity of a liquid (A) Is zero for incompressible liquid (B) Decreases with pressure (C) Is independent of temperature & pressure (D) Increases with pressure

Description : The bulk modulus of elasticity of a liquid (A) Is zero for incompressible liquid (B) Decreases with pressure (C) Is independent of temperature & pressure (D) Increases with pressure

Last Answer : (D) Increases with pressure

The dimensional formula of bulk modulus of elasticity is same as that of the (A) Pressure (B) Density (C) Force (D) None of these

Description : The dimensional formula of bulk modulus of elasticity is same as that of the (A) Pressure (B) Density (C) Force (D) None of these

Last Answer : Option A

The approximate height of a blast furnace having a useful volume of 2000 m3is about __________ metres (A) 25 (B) 35 (C) 55 (D) 75

Description : The approximate height of a blast furnace having a useful volume of 2000 m3is about __________ metres (A) 25 (B) 35 (C) 55 (D) 75

Last Answer : (C) 55

The approximate value of the ratio between direct tensile strength and flexural strength is (A) 0.33 (B) 0.5 (C) 0.75 (D) 1.0

Description : The approximate value of the ratio between direct tensile strength and flexural strength is (A) 0.33 (B) 0.5 (C) 0.75 (D) 1.0

Last Answer : Answer: Option B

How much paddy seed is needed for transplanting one hectare area by SRI technique(a) 30 – 35 kg (b) 1 •— 1•5 kg (c) 5-6kg (d) 10-12kg

Description : How much paddy seed is needed for transplanting one hectare area by SRI technique(a) 30 – 35 kg (b) 1 •— 1•5 kg (c) 5-6kg (d) 10-12kg

Last Answer : (c) 5-6kg

If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Description : If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Last Answer : Answer: Option D

A short column 20 cm × 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on the column, should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these

Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these

Last Answer : Answer: Option B

Operating temperature and pressure in catalytic reforming is about (A) 1-5 Kgf/cm2 & 200°C (B) 15-45 Kgf/cm2 & 450-550°C (C) 50 - 75 kgf/cm2 & 600 - 800°C (D) 5-10 kgf/cm2 & 150 - 250°C

Description : Operating temperature and pressure in catalytic reforming is about (A) 1-5 Kgf/cm2 & 200°C (B) 15-45 Kgf/cm2 & 450-550°C (C) 50 - 75 kgf/cm2 & 600 - 800°C (D) 5-10 kgf/cm2 & 150 - 250°C

Last Answer : (B) 15-45 Kgf/cm2 & 450-550°C

The dimensions of modulus of elasticity are a.MLT-2 b.107 dynes c.MLT-1 d.ML-2T-1 e.ML-1T-2

Description : The dimensions of modulus of elasticity are a.MLT-2 b.107 dynes c.MLT-1 d.ML-2T-1 e.ML-1T-2

Last Answer : e. ML-1T-2

What is the SI unit of Young’s modulus of elasticity? -Do You Know?

Description : What is the SI unit of Young’s modulus of elasticity? -Do You Know?

Last Answer : answer:

Dimension of modulus of elasticity is (a) ML–2T–2 (b) M–1L–1T–2 (c) ML–1T–2 (d) ML–1T–1

Description : Dimension of modulus of elasticity is (a) ML–2T–2 (b) M–1L–1T–2 (c) ML–1T–2 (d) ML–1T–1

Last Answer : Ans:(c)

The dimensional formula ML⁻¹T⁻² corresponds to – (1) Modulus of elasticity (2) Viscosity (3) Moment of a force (4) Thrust

Description : The dimensional formula ML⁻¹T⁻² corresponds to – (1) Modulus of elasticity (2) Viscosity (3) Moment of a force (4) Thrust

Last Answer : (1) Modulus of elasticity Explanation: M Li- T-2 is the dimension of any quantity that is force per unit area such as Pressure or Stress, Young's Modulus, Bulk Modulus, Modulus of Rigidity, ... the ratio of the stress applied to a body or substance to the resulting strain within the elastic limit.

What is the SI unit of Young’s modulus of elasticity?

Description : What is the SI unit of Young’s modulus of elasticity?

Last Answer : Newton/m2

Velocity of sound waves through any material depends on A. the material's density ‘d’ only B. the material's density ‘d’ as well as its modulus of elasticity ‘E’ C. the material's modulus of elasticity ‘E’ only D. neither the material's density ‘d’ nor its modulus of elasticity ‘E’

Description : Velocity of sound waves through any material depends on A. the material's density ‘d’ only B. the material's density ‘d’ as well as its modulus of elasticity ‘E’ C. the material's modulus of elasticity ‘E’ only D. neither the material's density ‘d’ nor its modulus of elasticity ‘E’

Last Answer : the material's density ‘d’ as well as its modulus of elasticity ‘E’

Speed ‘v’ with which wave travels through a medium is given by A. modulus of elasticity/density of the medium B. modulus of elasticity/√(density of the medium) C. √(modulus of elasticity/density of the medium) D. v=d/t

Description : Speed ‘v’ with which wave travels through a medium is given by A. modulus of elasticity/density of the medium B. modulus of elasticity/√(density of the medium) C. √(modulus of elasticity/density of the medium) D. v=d/t

Last Answer : √(modulus of elasticity/density of the medium)

Which of the following is measure of stiffness? a) Modulus of elasticity b) Modulus of plasticity c) Resilience d) Toughness

Description : Which of the following is measure of stiffness? a) Modulus of elasticity b) Modulus of plasticity c) Resilience d) Toughness

Last Answer : a) Modulus of elasticity

The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Description : The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Last Answer : b) Yield strength

The ratio of shear stress and shear strain of an elastic material, is (A) Modulus of Rigidity (B) Shear Modulus (C) Modulus of Elasticity (D) Both (a) and (b)

Description : The ratio of shear stress and shear strain of an elastic material, is  (A) Modulus of Rigidity  (B) Shear Modulus  (C) Modulus of Elasticity  (D) Both (a) and (b) 

Last Answer : (D) Both (a) and (b) 

If M, I, R, E, F, and Y are the bending moment, moment of inertia, radius of curvature, modulus of elasticity stress and the depth of the neutral axis at section, then (A) M/I = R/E = F/Y (B) I/M = R/E = F/Y (C) M/I = E/R = E/Y (D) M/I = E/R = Y/F

Description : If M, I, R, E, F, and Y are the bending moment, moment of inertia, radius of curvature, modulus of  elasticity stress and the depth of the neutral axis at section, then  (A) M/I = R/E = F/Y (B) I/M = R/E = F/Y (C) M/I = E/R = E/Y (D) M/I = E/R = Y/F

Last Answer : (C) M/I = E/R = E/Y

If E, N, K and 1/m are modulus of elasticity, modulus of rigidity. Bulk modulus and Poisson ratio of the material, the following relationship holds good (A) E = 3K (1 - 2/m) (B) E = 2N (1 + 1/m) (C) (3/2)K (1 - 2/m) = N (1 + 1/m) (D) All the above

Description : If E, N, K and 1/m are modulus of elasticity, modulus of rigidity. Bulk modulus and Poisson ratio of  the material, the following relationship holds good  (A) E = 3K (1 - 2/m)  (B) E = 2N (1 + 1/m)  (C) (3/2)K (1 - 2/m) = N (1 + 1/m)  (D) All the above 

Last Answer : (D) All the above 

Euler's formula states that the buckling load for a column of length , both ends hinged and whose least moment of inertia and modulus of elasticity of the material of the column are and respectively, is given by the relation (A) P = ²EI/l² (B) P = /EI (C) P = /l² (D) P = ²EI/l

Description : Euler's formula states that the buckling load for a column of length , both ends hinged and whose least moment of inertia and modulus of elasticity of the material of the column are and respectively, is given by the relation (A) P = ²EI/l² (B) P = /EI (C) P = /l² (D) P = ²EI/l

Last Answer : (A) P = ²EI/l²

The bulk modulus of elasticity (A) Has the dimensions of 1/pressure (B) Increases with pressure (C) Is large when fluid is more compressible (D) Is independent of pressure and viscosity

Description : The bulk modulus of elasticity (A) Has the dimensions of 1/pressure (B) Increases with pressure (C) Is large when fluid is more compressible (D) Is independent of pressure and viscosity

Last Answer : Answer: Option B

bulk modulus of elasticity with increase in pressure (A) Increases (B) Decreases (C) Remain constant (D) Increases first up to certain limit and then decreases

Description : bulk modulus of elasticity with increase in pressure (A) Increases (B) Decreases (C) Remain constant (D) Increases first up to certain limit and then decreases

Last Answer : Answer: Option A

(A) Absolute temperature (B) Temperature (C) Density (D) Modulus of elasticity

Description : (A) Absolute temperature (B) Temperature (C) Density (D) Modulus of elasticity

Last Answer : Answer: Option A

Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is proportional to the age of the member at the time of loading. (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members

Description : Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is ... to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members

Last Answer : (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete

Which of the following statements refer to correct purpose as regards testing of concrete by ultrasonic pulse velocity method? 1. To assess the quality of concrete in-situ. 2. To determine the dynamic modulus of elasticity of concrete. 3. To locate the presence of cracks in it (a) 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d)1, 2 and 3

Description : Which of the following statements refer to correct purpose as regards testing of concrete by ultrasonic pulse velocity method? 1. To assess the quality of concrete in-situ. 2. To determine the dynamic modulus of elasticity of concrete. 3 ... and 2 only (b) 1 and 3 only (c) 2 and 3 only (d)1, 2 and 3

Last Answer : (d)1, 2 and 3

Modulus of elasticity of concrete is increased with (a) Higher W/C ratio (b) Shorter curing period (c) Lesser vibration (d) Increase in age

Description : Modulus of elasticity of concrete is increased with (a) Higher W/C ratio (b) Shorter curing period (c) Lesser vibration (d) Increase in age

Last Answer : (d) Increase in age

Modulus of elasticity of concrete is primarily influenced by [ A ] Elastic properties of aggregate [ B ] Curing of concrete [ C ] Age of concrete [ D ] Mix proportion and type of cement

Description : Modulus of elasticity of concrete is primarily influenced by [ A ] Elastic properties of aggregate [ B ] Curing of concrete [ C ] Age of concrete [ D ] Mix proportion and type of cement

Last Answer : [ A ] Elastic properties of aggregate

As per IS: 456-2000, modulus of elasticity of concrete (in N/mm2) is given by [ A ] 5700 vfCK [ B ] 5000 vfCK [ C ] 3700 vfCK [ D ] 3000 vfCK

Description : As per IS: 456-2000, modulus of elasticity of concrete (in N/mm2) is given by [ A ] 5700 vfCK [ B ] 5000 vfCK [ C ] 3700 vfCK [ D ] 3000 vfCK

Last Answer : [ B ] 5000 vfCK

The ductility of metal is usually expressed in terms of the: A. Yield strength (point where the material is not longer elastic) B. Percent elongation C. Modulus of elasticity (stiffness of the material)

Description : The ductility of metal is usually expressed in terms of the: A. Yield strength (point where the material is not longer elastic) B. Percent elongation C. Modulus of elasticity (stiffness of the material)

Last Answer : B. Percent elongation

A Gold clasp is more elastic than Cobalt Chrome, but Co-Chrome has high modulus of elasticity. A. The first statement is false the second is true B. Both are true C. The first is true the second is false D. Both are false

Description : A Gold clasp is more elastic than Cobalt Chrome, but Co-Chrome has high modulus of elasticity. A. The first statement is false the second is true B. Both are true C. The first is true the second is false D. Both are false

Last Answer : B. Both are true

Modulus of elasticity is defined as: A. The stress at the proportional limit B. The stress-strain ratio within the proportional limit

Description : Modulus of elasticity is defined as: A. The stress at the proportional limit B. The stress-strain ratio within the proportional limit

Last Answer : B. The stress-strain ratio within the proportional limit