Size reduction of __________ is accomplished in steam heated rollers and roll crushers. (A) Resins (B) Gums (C) Hard rubber (D) Waxes

Size reduction of __________ is accomplished in steam heated rollers
and roll crushers.
(A) Resins
(B) Gums
(C) Hard rubber
(D) Waxes
by

1 Answer

Answer :

(C) Hard rubber
by

Related questions

Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not exceed 4 (C) Both the rolls run necessarily at the same speed (D) Reduction ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Description : Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not ... ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Last Answer : (C) Both the rolls run necessarily at the same speed

Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers

Description : Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers

Last Answer : (A) Rod mills

Toothed roll crushers achieve size reduction by (A) Tearing (shear) and compression (B) Impact and attrition (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Toothed roll crushers achieve size reduction by (A) Tearing (shear) and compression (B) Impact and attrition (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these

Description : Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these

Last Answer : (B) Toothed roll

The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Description : The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Last Answer : (B) Roll

Size reduction mechanism used in Jaw crushers is (A) Attrition (B) Compression

Description : Size reduction mechanism used in Jaw crushers is (A) Attrition (B) Compression

Last Answer : (B) Compression

Size reduction of asbestos and mica is done by (A) Hammer mills (B) Rod mills (C) Gyratory crushers (D) Crushing rolls

Description : Size reduction of asbestos and mica is done by (A) Hammer mills (B) Rod mills (C) Gyratory crushers (D) Crushing rolls

Last Answer : (A) Hammer mills

Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one(B) There are only four methods namely compression, impact, attrition andcutting, which the size reduction equipments employ(C) Cutting machines mainly employ 'attrition' for size reduction of solids(D) Operating principles of Dodge and Blake jaw crushers are combined inthe working of universal jaw crushers

Description : Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one (B) There are only four methods namely compression, impact ... Operating principles of Dodge and Blake jaw crushers are combined in the working of universal jaw crushers

Last Answer : (C) Cutting machines mainly employ 'attrition' for size reduction of solids

D-Mannose is present in some plant products like (A) Resins (B) Pectins (C) Mucilage (D) Gums

Description : D-Mannose is present in some plant products like (A) Resins (B) Pectins (C) Mucilage (D) Gums

Last Answer : D

Which one among the following is not removed as a waste product from the body of a plant? (a) Resins and Gums (b) Urea (c) Dry Leaves (d) Excess Water

Description : Which one among the following is not removed as a waste product from the body of a plant? (a) Resins and Gums (b) Urea (c) Dry Leaves (d) Excess Water

Last Answer : Answer: (b)

Crushing of mineral particles is accomplished in a 'cage mill', when one or more alloy steel bars are revolved in opposite directions. It is a type of __________ mill. (A) Impact (B) Roll (C) Vibratory (D) None of these

Description : Crushing of mineral particles is accomplished in a 'cage mill', when one or more alloy steel bars are revolved in opposite directions. It is a type of __________ mill. (A) Impact (B) Roll (C) Vibratory (D) None of these

Last Answer : (A) Impact

Pick out the correct statement. (A) Noise from ball mills can be dealt with by fibre glass lined enclosures (B) Noise from vibrating chutes can be reduced by lining the metallic chute with rubber (C) Noise of conveyor belt system is reduced by using urethane coated cloth conveyor belts and rubber/plastic covered metallic rollers (D) All (A), (B) & (C)

Description : Pick out the correct statement. (A) Noise from ball mills can be dealt with by fibre glass lined enclosures (B) Noise from vibrating chutes can be reduced by lining the metallic chute with rubber (C) Noise ... cloth conveyor belts and rubber/plastic covered metallic rollers (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Reduction ratio of crushers is the (A) Ratio of feed opening to discharge opening (B) Ratio of discharge opening to feed opening (C) Determining factor for minimum dia of the feed and the product (D) None of these

Description : Reduction ratio of crushers is the (A) Ratio of feed opening to discharge opening (B) Ratio of discharge opening to feed opening (C) Determining factor for minimum dia of the feed and the product (D) None of these

Last Answer : (A) Ratio of feed opening to discharge opening

Which of the following is not a dielectric material? (A) Cotton, silk and paper (B) Asbestos, glass, porcelain and mica (C) Rubber and polymeric resins (D) All refractory materials

Description : Which of the following is not a dielectric material? (A) Cotton, silk and paper (B) Asbestos, glass, porcelain and mica (C) Rubber and polymeric resins (D) All refractory materials

Last Answer : Option C

Why do they call steam rollers, steam rollers? They don't produce, get rid of, or have anythong to do with steam?

Description : Why do they call steam rollers, steam rollers? They don't produce, get rid of, or have anythong to do with steam?

Last Answer : Steam roller engines are powered by steam. Otherwise, they are only road rollers.

Why do they call steam rollers, steam rollers?

Description : Why do they call steam rollers, steam rollers?

Last Answer : They’re powered by steam engines (or at least, they were).

Cation exchange resins (0.3 to 1 mm size) used in water treatment is prepared from __________ resins. (A) Epoxy (B) Phenol formaldehyde (C) Urea formaldehyde (D) Melamine formaldehyde

Description : Cation exchange resins (0.3 to 1 mm size) used in water treatment is prepared from __________ resins. (A) Epoxy (B) Phenol formaldehyde (C) Urea formaldehyde (D) Melamine formaldehyde

Last Answer : (C) Urea formaldehyde

Bond crushing law (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law (B) Is less realistic in estimating the power requirements of commercial crushers (C) States that the work required to form particle of any size from very large feed is proportional to the square root of the volume to surface ratio of the product (D) States that the work required for the crushing is proportional to the new surface created

Description : Bond crushing law (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law (B) Is less realistic in estimating the power requirements of commercial crushers ( ... (D) States that the work required for the crushing is proportional to the new surface created

Last Answer : (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law

Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will just take hold of a particle and draw it in the crushing zone (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing (D) Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Description : Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will ... Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Last Answer : (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing

Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Description : Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Last Answer : (B) Roll crusher

Complete removal of __________ from gasoline is done by Unisol process using caustic soda and methyl alcohol. (A) Waxes (B) Mercaptans (C) Asphalt (D) Diolefins

Description : Complete removal of __________ from gasoline is done by Unisol process using caustic soda and methyl alcohol. (A) Waxes (B) Mercaptans (C) Asphalt (D) Diolefins

Last Answer : (B) Mercaptans

Non sulphonated hard bakelites are not used for making (A) Ion-exchange resins (B) Fountain pen barrels (C) Formica table tops (D) Combs

Description : Non sulphonated hard bakelites are not used for making (A) Ion-exchange resins (B) Fountain pen barrels (C) Formica table tops (D) Combs

Last Answer : (A) Ion-exchange resins

Thermoplastic resins usually(A) Remain hard as long as they are hot(B) Cannot be reclaimed from waste(C) Permanent setting resins(D) Less brittle than thermosetting resins

Description : Thermoplastic resins usually (A) Remain hard as long as they are hot (B) Cannot be reclaimed from waste (C) Permanent setting resins (D) Less brittle than thermosetting resins

Last Answer : (D) Less brittle than thermosetting resins

Which is not accomplished in an underfired furnace? (A) Increase in heating capacity/m2 of floor space (B) Elimination of cold spot at the bottom of the charge (C) Reduction in the temperature of furnace gases (D) Protection of the periphery of the charge from excessive radiation

Description : Which is not accomplished in an underfired furnace? (A) Increase in heating capacity/m2 of floor space (B) Elimination of cold spot at the bottom of the charge (C) Reduction in the temperature of furnace gases (D) Protection of the periphery of the charge from excessive radiation

Last Answer : (A) Increase in heating capacity/m2 of floor space

Ball mills and tube mills with flint or porcelain balls are used for size reduction of (A) Asbestos (B) Rubber (C) Non-metallic ores (D) Limestone

Description : Ball mills and tube mills with flint or porcelain balls are used for size reduction of (A) Asbestos (B) Rubber (C) Non-metallic ores (D) Limestone

Last Answer : (C) Non-metallic ores

__________ are produced by reacting polybasic acid (e.g. Phthalic anhydride) with polyhydric alcohol (e.g., glycerol). (A) Unsaturated polyester (B) Alkyd resins (C) Saturated polyester (D) Amino resins

Description : __________ are produced by reacting polybasic acid (e.g. Phthalic anhydride) with polyhydric alcohol (e.g., glycerol). (A) Unsaturated polyester (B) Alkyd resins (C) Saturated polyester (D) Amino resins

Last Answer : (B) Alkyd resins

Cation exchange resins used in water treatment is made from __________ resin. (A) Urea formaldehyde (B) Epoxy (C) Amino (D) Phenolic

Description : Cation exchange resins used in water treatment is made from __________ resin. (A) Urea formaldehyde (B) Epoxy (C) Amino (D) Phenolic

Last Answer : (A) Urea formaldehyde

__________ resins are produced by the condensation polymerisation of formaldehyde with urea or melamine. (A) Epoxy (B) Amino (C) Alkyd (D) Phenolic

Description : __________ resins are produced by the condensation polymerisation of formaldehyde with urea or melamine. (A) Epoxy (B) Amino (C) Alkyd (D) Phenolic

Last Answer : (B) Amino

A __________ is a type of heat exchange system where water is heated to its' boiling point via combustion of a fuel blown through a tube submerged in water. a. Condensate loop b. Hyperbolic cooling tower c. Steam boiler d. All of above

Description : A __________ is a type of heat exchange system where water is heated to its' boiling point via combustion of a fuel blown through a tube submerged in water. a. Condensate loop b. Hyperbolic cooling tower c. Steam boiler d. All of above

Last Answer : c. Steam boiler

Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Description : Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Last Answer : (C) Gyratory crusher

Pick out the wrong statement. (A) Hammer crushers operate by impact action (B) Standard screens have circular opening (C) With increase in mesh number of screens, their diameter in microns decreases (D) 200 mesh screen has 200 openings per linear cm

Description : Pick out the wrong statement. (A) Hammer crushers operate by impact action (B) Standard screens have circular opening (C) With increase in mesh number of screens, their diameter in microns decreases (D) 200 mesh screen has 200 openings per linear cm

Last Answer : (D) 200 mesh screen has 200 openings per linear cm

Basic slag is not ground in (A) Jaw crushers (B) Ball mills

Description : Basic slag is not ground in (A) Jaw crushers (B) Ball mills

Last Answer : (A) Jaw crushers

Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Description : Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Last Answer : (A) Have greater capacity per unit of discharge area

As per Taggart's formula, the capacity (kg/hr) of Jaw & Gyratory crushers (for gapes of 10 to 60 cms) is equal to (where, L = Length of feed opening, cms S = Maximum width of discharge opening, cms). (A) LS (B) 93 LS (C) 250 LS (D) √(LS)

Description : As per Taggart's formula, the capacity (kg/hr) of Jaw & Gyratory crushers (for gapes of 10 to 60 cms) is equal to (where, L = Length of feed opening, cms S = Maximum width of discharge opening, cms). (A) LS (B) 93 LS (C) 250 LS (D) √(LS)

Last Answer : (B) 93 LS

____ dissolve in water and are made as powders, granules (small hard pieces), liquids, or other specialpurpose forms. a. Dyes c. Sweeteners b. Lakes d. Gums

Description : ____ dissolve in water and are made as powders, granules (small hard pieces), liquids, or other specialpurpose forms. a. Dyes c. Sweeteners b. Lakes d. Gums

Last Answer : a. Dyes

Horsepower required for a roll crusher is directly proportional to its (A) Reduction ratio (B) Capacity(C) Both (A) & (B)(D) Neither (A) nor (B)

Description : Horsepower required for a roll crusher is directly proportional to its (A) Reduction ratio (B) Capacity (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

In a roll crusher, the specific power consumption and the production rate is affected by the (A) Reduction ratio (B) Differential roll speed (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : In a roll crusher, the specific power consumption and the production rate is affected by the (A) Reduction ratio (B) Differential roll speed (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Waxes present in petroleum products (A) Can be separated out by distillation(B) Are not soluble in them(C) Crystallise out at low temperature(D) Decrease their viscosity

Description : Waxes present in petroleum products (A) Can be separated out by distillation (B) Are not soluble in them (C) Crystallise out at low temperature (D) Decrease their viscosity

Last Answer : (C) Crystallise out at low temperature

Which parameter is used for the grading of paraffin waxes? (A) Specific gravity (B) Melting point (C) Viscosity (D) Penetration number

Description : Which parameter is used for the grading of paraffin waxes? (A) Specific gravity (B) Melting point (C) Viscosity (D) Penetration number

Last Answer : (C) Viscosity

A boiling water reactor is the one, in which the (A) Coolant water is allowed to boil in the core of the reactor (B) Coolant water, after being heated in the reactor core, generates steam in a boiler (C) Pressurised water is pumped into the core (D) Fuel and the coolant are thoroughly mixed to form a homogeneous solution

Description : A boiling water reactor is the one, in which the (A) Coolant water is allowed to boil in the core of the reactor (B) Coolant water, after being heated in the reactor core, generates steam ... water is pumped into the core (D) Fuel and the coolant are thoroughly mixed to form a homogeneous solution

Last Answer : (A) Coolant water is allowed to boil in the core of the reactor

Air is best heated with steam in a heat exchanger of (A) Plate type (B) Double pipe type with fin on steam side (C) Double pipe type with fin on air side (D) Shell and tube type

Description : Air is best heated with steam in a heat exchanger of (A) Plate type (B) Double pipe type with fin on steam side (C) Double pipe type with fin on air side (D) Shell and tube type

Last Answer : (C) Double pipe type with fin on air side

Air is to be heated by condensing steam. Two heat exchangers are available (i) a shell and tube heat exchanger and (ii) a finned tube heat exchanger. Tube side heat transfer area are equal in both the cases. The recommended arrangement is (A) Finned tube heat exchanger with air inside and steam outside (B) Finned tube heat exchanger with air outside and steam inside (C) Shell and tube heat exchanger with air inside tubes and steam on shell side (D) Shell and tube heat exchanger with air on shell side and steam inside tubes

Description : Air is to be heated by condensing steam. Two heat exchangers are available (i) a shell and tube heat exchanger and (ii) a finned tube heat exchanger. Tube side heat transfer area are equal in both ... steam on shell side (D) Shell and tube heat exchanger with air on shell side and steam inside tubes

Last Answer : (B) Finned tube heat exchanger with air outside and steam inside

A process stream of dilute aqueous solution flowing at the rate of10 Kg.s -1 is to be heated. Steam condensate at 95°C is available for heating purpose, also at a rate of 10 Kg.s -1 . A 1 - 1 shell and tube heat exchanger is available. The best arrangement is (A) Counter flow with process stream on shell side (B) Counter flow with process stream on tube side (C) Parallel flow with process stream on shell side (D) Parallel flow with process stream on tube side

Description : A process stream of dilute aqueous solution flowing at the rate of10 Kg.s -1 is to be heated. Steam condensate at 95°C is available for heating purpose, also at a rate of 10 Kg.s -1 . A 1 ... side (C) Parallel flow with process stream on shell side (D) Parallel flow with process stream on tube side

Last Answer : (A) Counter flow with process stream on shell side

In a gas-liquid shell and tube heat exchanger, the(A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure gases are corrosive in nature (C) Gases to be heated/cooled is normally routed through the shell side, because the corrosion caused by the cooling water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Description : In a gas-liquid shell and tube heat exchanger, the (A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure ... water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

LMTD for counter-flow and parallel flow heat exchanger will be the same, when the (A) Cold fluid is heated to a certain temperature by condensing steam (isothermal fluid) (B) Outlet temperature of both the hot and cold fluid are same (C) Outlet temperature of hot fluid is less than the outlet temperature of the cold fluid (D) None of these

Description : LMTD for counter-flow and parallel flow heat exchanger will be the same, when the (A) Cold fluid is heated to a certain temperature by condensing steam (isothermal fluid) (B) Outlet temperature of ... temperature of hot fluid is less than the outlet temperature of the cold fluid (D) None of these

Last Answer : (A) Cold fluid is heated to a certain temperature by condensing steam (isothermal fluid)

Pick out the wrong statement. (A) In process heat exchangers, saturated steam is preferred over the superheated steam (B) The maximum is the emissive power of a surface at a temperature T1 occurs at a wavelength of λ1 . If the surface temperature is halved, the maximum in the emissive power would occur at a wavelength of 0.5 λ1 (C) When a vertical plate is heated in infinite air environmental under natural convection conditions, the velocity profile in air, normal to the plate, exhibits a maximum

Description : Pick out the wrong statement. (A) In process heat exchangers, saturated steam is preferred over the superheated steam (B) The maximum is the emissive power of a surface at a temperature T1 ... under natural convection conditions, the velocity profile in air, normal to the plate, exhibits a maximum

Last Answer : (B) The maximum is the emissive power of a surface at a temperature T1 occurs at a wavelength of λ1 . If the surface temperature is halved, the maximum in the emissive power would occur at a wavelength of 0.5 λ1

In a heat exchanger with steam outside the tubes, a liquid gets heated to 45°C, when its flow velocity in the tubes is 2 m/s. If the flow velocity is reduced to 1 m/s, other things remaining the same, the temperature of the exit liquid will be (A) Less than 45°C (B) More than 45°C (C) Equal to 45°C (D) Initially decreases and remains constant thereafter

Description : In a heat exchanger with steam outside the tubes, a liquid gets heated to 45°C, when its flow velocity in the tubes is 2 m/s. If the flow velocity is reduced to 1 m/s, other things remaining ... than 45°C (B) More than 45°C (C) Equal to 45°C (D) Initially decreases and remains constant thereafter

Last Answer : (B) More than 45°C

Compound coke ovens are those which can be heated by (A) Both steam and electrical power (B) Lean gas (e.g., B.F. gas) (C) Rich gas (e.g., coke oven gas) (D) Both (B) and (C)

Description : Compound coke ovens are those which can be heated by (A) Both steam and electrical power (B) Lean gas (e.g., B.F. gas) (C) Rich gas (e.g., coke oven gas) (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)