Description : In a roll crusher, the specific power consumption and the production rate is affected by the (A) Reduction ratio (B) Differential roll speed (C) Both (A) and (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) and (B)
Description : Toothed roll crushers achieve size reduction by (A) Tearing (shear) and compression (B) Impact and attrition (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) & (B)
Description : Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher
Last Answer : (B) Roll crusher
Description : Energy consumption in a crusher decreases with increase in the (A) Size of the product (at constant feed size) (B) Capacity of the crushing machine (C) Size of feed (at constant reduction ratio) (D) All (A), (B) & (C)
Last Answer : (D) All (A), (B) & (C)
Description : The grinding in a hammer crusher takes place due to the (A) Attrition (B) Impact (C) Both (A) & (B) (D) Neither (A) nor (B
Description : During size reduction by a jaw crusher, the energy consumed decreases with the (A) Decreasing size of product at constant size of feed (B) Decreasing machine capacity (C) Increasing size of feed at constant reduction ratio (D) None of these
Last Answer : (C) Increasing size of feed at constant reduction ratio
Description : Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these
Last Answer : (B) Toothed roll
Description : Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not ... ratio and differential roll speed affect production rate & energy consumed per unit of surface produced
Last Answer : (C) Both the rolls run necessarily at the same speed
Description : Pick out the correct statement: (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products (B) The operating cost of ... upon the specific gravity of the minerals (D) Asphalt is best crushed using toothed roll crusher
Last Answer : (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products
Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types
Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size
Description : With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed
Last Answer : (B) Head varies as the square of speed
Description : At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Fanning friction factor for laminar flow of fluid in a circular pipe is (A) Not a function of the roughness of pipe wall (B) Inversely proportional to Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)
Description : In case of simple harmonic motion, displacement is proportional to the (A) Velocity (B) Acceleration (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : B) Acceleration
Description : Which is a secondary crusher for a hard & tough stone? (A) Jaw crusher (B) Cone crusher (C) Impact crusher (D) Toothed roll crushe
Last Answer : (B) Cone crusher
Description : The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)
Description : Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)
Description : In case of a hammer crusher, (A) Crushing takes place by impact breaking (B) Maximum acceptable feed size is 30 cms (C) Reduction ratio can be varied by adjusting the distance from cage to hammers (D) All (A), (B) and (C)
Description : In a roll crusher, both the rolls (A) Have the same diameter (B) Are rotated towards each other (C) Run either at the same or different speeds (D) All (A), (B) and (C
Last Answer : (D) All (A), (B) and (C
Description : Filtration capacity of a rotary drum vacuum filter depends upon the (A) Cake thickness (B) Characteristics of the feed slurry (C) Both (A) & (B) (D) Neither (A) nor (B)
Description : The heating capacity of muffle furnace depends on the (A) Surface area & emissivity of the stock (B) Properties of the muffle wall (temperature, area, and emissivity) (C) Both (A) & (B) (D) Neither (A) nor (B)
Description : . In magnetic flow meters, voltage generation is (A) Due to the motion of conducting fluid through an externally generated uniform field (B) Proportional to the fluid velocity (C) Both (A) and (B) (D) Neither (A) nor (B)
Description : . Kick's law assumes that the energy required for size reduction is proportional to the logarithm of the ratio between the initial and the final diameters. The unit of Kick's constant is (A) kW. sec/kg (B) kWh/kg (C) kWh/sec. kg (D) kg/sec
Last Answer : (A) kW. sec/kg
Description : For crushing of solids, the Rittinger's law states that the work required for crushing is proportional to (A) The new surface created (B) The size reduction ratio (C) The change in volume due to crushing (D) None of these
Last Answer : (A) The new surface created
Description : Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)
Last Answer : (A) cos α = (dr + dp)/(dr + df)
Description : Which of the following is not an ultrafine grinder (colloid mill)? (A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification
Last Answer : (C) Toothed roll crusher
Description : Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill
Last Answer : (B) Hammer crusher
Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher
Last Answer : (B) Ball mill
Description : Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill
Last Answer : (C) Gyratory crusher
Description : Fibrous material is broken by a (A) Roll-crusher (B) Squirrel-cage disintegrator (C) Ball mill (D) Tube mill
Last Answer : (B) Squirrel-cage disintegrator
Description : Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher
Last Answer : (B) Gyratory crusher
Description : Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher
Description : Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill
Last Answer : (C) Tube mill
Description : Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher
Description : Refractive index of a petrofuel which is the ratio of velocity of light in air to its velocity in the petrofuel gives an indication if its (A) Molecular weight (B) Aromatics content (C) Both ‘a’ & ‘b’ (D) Neither ‘a’ nor ‘b’
Last Answer : (C) Both ‘a’ & ‘b
Description : With increase in carbide/graphite ratio in cast iron, its (A) Hardness & brittleness increases (B) Ductility decreases (C) Both (A) and (B) (D) Neither (A) nor (B)
Description : The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times
Last Answer : (B) 2.5 times
Description : The quantity of seepage of water through soils is proportional to (A) Coefficient of permeability of soil (B) Total head loss through the soil (C) Neither (a) nor (b) (D) Both (a) and (b)
Last Answer : Answer: Option D
Description : The ratio of Murphree plate efficiency to point efficiency is always > 1 in a __________ flow model. (A) Plug (B) Perfectly mixed (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (A) Plug
Description : The ratio of Murphree plate efficiency to point efficiency is 1 in a __________ flow model. (A) Plug (B) Perfectly mixed (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (B) Perfectly mixed
Description : In case of constant underflow extraction operation, the __________ atall solute concentration. (A) Solids are drained to the same extent (B) Ratio of the insoluble to solution is constant (C) Both (A) & (B) (D) Neither (A) nor (B)
Description : Trouton's ratio of __________ liquids is calculated using Kistyakowsky equation. (A) Polar (B) Non-polar (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (B) Non-polar
Description : Factor of safety against sliding of a slope, is the ratio of (A) Actual cohesion to that required to maintain stability of slope (B) Shear strength to shear stress along the surface (C) Neither (a) nor (b) (D) Both (a) and (b)
Description : Capacity of a rotary dryer depends on its (A) rpm (B) Inclination with ground surface (C) Both (A) and (B) (D) Neither (A) nor (B)
Description : Choke crushing (in case of a Jaw crusher) compared to free crushing (A) Results in increased capacity (B) Consumes less power (C) Consumes more power (D) Both (A) and (C)
Last Answer : (C) Consumes more power
Description : SHM is the motion in which acceleration of the body is proportional to its displacement and directed towards the mean position. A. True B. False C. Neither True Nor False D. None
Last Answer : A. True
Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser
Last Answer : (C) Jaw crusher
Description : Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the (A) Blake jaw crusher (B) Cage mill (C) Stamp mill (D) Bradford's breaker
Last Answer : (B) Cage mill
Description : Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill (B) Ball mill, Jaw crusher, Fluid ... C) Fluid energy mill, Jaw crusher, Ball mill (D) Fluid energy mill, Ball mill, Jaw crusher
Last Answer : (A) Jaw crusher, Ball mill, Fluid energy mill
Description : Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one (B) There are only four methods namely compression, impact ... Operating principles of Dodge and Blake jaw crushers are combined in the working of universal jaw crushers
Last Answer : (C) Cutting machines mainly employ 'attrition' for size reduction of solids