Toothed roll crushers achieve size reduction by (A) Tearing (shear) and compression (B) Impact and attrition (C) Both (A) & (B) (D) Neither (A) nor (B)

Toothed roll crushers achieve size reduction by
(A) Tearing (shear) and compression
(B) Impact and attrition
(C) Both (A) & (B)
(D) Neither (A) nor (B)
by

1 Answer

Answer :

(C) Both (A) & (B)
by

Related questions

Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one(B) There are only four methods namely compression, impact, attrition andcutting, which the size reduction equipments employ(C) Cutting machines mainly employ 'attrition' for size reduction of solids(D) Operating principles of Dodge and Blake jaw crushers are combined inthe working of universal jaw crushers

Description : Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one (B) There are only four methods namely compression, impact ... Operating principles of Dodge and Blake jaw crushers are combined in the working of universal jaw crushers

Last Answer : (C) Cutting machines mainly employ 'attrition' for size reduction of solids

General mechanism of size reduction in intermediate and fine grinder is by (A) Cutting action (B) Compression (C) Compression and tearing (D) Impact and attrition

Description : General mechanism of size reduction in intermediate and fine grinder is by (A) Cutting action (B) Compression (C) Compression and tearing (D) Impact and attrition

Last Answer : (D) Impact and attrition

The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Size reduction mechanism used in Jaw crushers is (A) Attrition (B) Compression

Description : Size reduction mechanism used in Jaw crushers is (A) Attrition (B) Compression

Last Answer : (B) Compression

Colloid mills achieve size reduction mainly by (A) Impact (B) Attrition (C) Cutting (D) Compression

Description : Colloid mills achieve size reduction mainly by (A) Impact (B) Attrition (C) Cutting (D) Compression

Last Answer : (B) Attrition

Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers

Description : Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers

Last Answer : (A) Rod mills

Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not exceed 4 (C) Both the rolls run necessarily at the same speed (D) Reduction ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Description : Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not ... ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Last Answer : (C) Both the rolls run necessarily at the same speed

The main size reduction operation in ultrafine grinders is (A) Cutting (B) Attrition (C) Compression (D) Impact

Description : The main size reduction operation in ultrafine grinders is (A) Cutting (B) Attrition (C) Compression (D) Impact

Last Answer : (B) Attrition

Maximum size reduction in a fluid energy mill is achieved by (A) Compression (B) Interparticle attrition (C) Cutting (D) Impact

Description : Maximum size reduction in a fluid energy mill is achieved by (A) Compression (B) Interparticle attrition (C) Cutting (D) Impact

Last Answer : (B) Interparticle attrition

Maximum size reduction in a ball mill is done by the, __________ action. (A) Attrition (B) Compression (C) Impact (D) Cutting

Description : Maximum size reduction in a ball mill is done by the, __________ action. (A) Attrition (B) Compression (C) Impact (D) Cutting

Last Answer : (C) Impact

The grinding in a hammer crusher takes place due to the (A) Attrition (B) Impact (C) Both (A) & (B) (D) Neither (A) nor (B

Description : The grinding in a hammer crusher takes place due to the (A) Attrition (B) Impact (C) Both (A) & (B) (D) Neither (A) nor (B

Last Answer : (C) Both (A) & (B)

Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these

Description : Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these

Last Answer : (B) Toothed roll

Size reduction of __________ is accomplished in steam heated rollers and roll crushers. (A) Resins (B) Gums (C) Hard rubber (D) Waxes

Description : Size reduction of __________ is accomplished in steam heated rollers and roll crushers. (A) Resins (B) Gums (C) Hard rubber (D) Waxes

Last Answer : (C) Hard rubber

For coarse reduction of hard solids, use (A) Impact (B) Attrition (C) Compression (D) Cutting

Description : For coarse reduction of hard solids, use (A) Impact (B) Attrition (C) Compression (D) Cutting

Last Answer : (C) Compression

Which is a secondary crusher for a hard & tough stone? (A) Jaw crusher(B) Cone crusher(C) Impact crusher(D) Toothed roll crushe

Description : Which is a secondary crusher for a hard & tough stone? (A) Jaw crusher (B) Cone crusher (C) Impact crusher (D) Toothed roll crushe

Last Answer : (B) Cone crusher

Horsepower required for a roll crusher is directly proportional to its (A) Reduction ratio (B) Capacity(C) Both (A) & (B)(D) Neither (A) nor (B)

Description : Horsepower required for a roll crusher is directly proportional to its (A) Reduction ratio (B) Capacity (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

In a roll crusher, the specific power consumption and the production rate is affected by the (A) Reduction ratio (B) Differential roll speed (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : In a roll crusher, the specific power consumption and the production rate is affected by the (A) Reduction ratio (B) Differential roll speed (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

The material is crushed in a gyratory crusher by the action of (A) Impact (B) Compression (C) Attrition (D) Cutting

Description : The material is crushed in a gyratory crusher by the action of (A) Impact (B) Compression (C) Attrition (D) Cutting

Last Answer : (B) Compression

Ultrafine grinders operate principally by (A) Slow compression (B) Impact (C) Attrition (D) Cutting action

Description : Ultrafine grinders operate principally by (A) Slow compression (B) Impact (C) Attrition (D) Cutting action

Last Answer : (C) Attrition

Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Size reduction of asbestos and mica is done by (A) Hammer mills (B) Rod mills (C) Gyratory crushers (D) Crushing rolls

Description : Size reduction of asbestos and mica is done by (A) Hammer mills (B) Rod mills (C) Gyratory crushers (D) Crushing rolls

Last Answer : (A) Hammer mills

Which of the following is not an ultrafine grinder (colloid mill)?(A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification

Description : Which of the following is not an ultrafine grinder (colloid mill)? (A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification

Last Answer : (C) Toothed roll crusher

Pick out the correct statement: (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products (B) The operating cost of shaking screen is more than that of a vibrating screen (C) Screen capacity does not depend upon the specific gravity of the minerals (D) Asphalt is best crushed using toothed roll crusher

Description : Pick out the correct statement: (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products (B) The operating cost of ... upon the specific gravity of the minerals (D) Asphalt is best crushed using toothed roll crusher

Last Answer : (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products

Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill

Description : Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill

Last Answer : (C) Gyratory crusher

Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Description : Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Last Answer : (B) Gyratory crusher

Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher

Description : Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher

Last Answer : (C) Toothed roll crusher

The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Description : The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Last Answer : (B) Roll

Which of the following size reduction equipments employs mainly attrition for ultrafine grinding? (A) Jet mills (B) Fluid energy mill (C) Micronizer (D) All (A), (B) and (C)

Description : Which of the following size reduction equipments employs mainly attrition for ultrafine grinding? (A) Jet mills (B) Fluid energy mill (C) Micronizer (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The rate of shear versus the shear stress curves are time dependent for __________ fluid. (A) Thixotropic (B) Rheopectic (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The rate of shear versus the shear stress curves are time dependent for __________ fluid. (A) Thixotropic (B) Rheopectic (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Aerodynamic noise resulting from turbulent gas flow is the most prevalent source of valve noise in fluid flow control. It is caused due to (A) Reynold stresses (B) Shear forces (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Aerodynamic noise resulting from turbulent gas flow is the most prevalent source of valve noise in fluid flow control. It is caused due to (A) Reynold stresses (B) Shear forces (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Soft & non-abrasive materials can be made into fines by (A) Attrition (B) Compression (C) Cutting (D) None of these

Description : Soft & non-abrasive materials can be made into fines by (A) Attrition (B) Compression (C) Cutting (D) None of these

Last Answer : (A) Attrition

A patient has improperly formed DEJ, reduction in size of pulp chamber, chipping and attrition of enamel that would MOSTLY be: A. Fluorosis B. Amelogenesis imperfecta C. Dentinogenesis imperfecta

Description : A patient has improperly formed DEJ, reduction in size of pulp chamber, chipping and attrition of enamel that would MOSTLY be: A. Fluorosis B. Amelogenesis imperfecta C. Dentinogenesis imperfecta

Last Answer : C. Dentinogenesis imperfecta

Reduction ratio of crushers is the (A) Ratio of feed opening to discharge opening (B) Ratio of discharge opening to feed opening (C) Determining factor for minimum dia of the feed and the product (D) None of these

Description : Reduction ratio of crushers is the (A) Ratio of feed opening to discharge opening (B) Ratio of discharge opening to feed opening (C) Determining factor for minimum dia of the feed and the product (D) None of these

Last Answer : (A) Ratio of feed opening to discharge opening

Pick out the wrong statement. (A) Hammer crushers operate by impact action (B) Standard screens have circular opening (C) With increase in mesh number of screens, their diameter in microns decreases (D) 200 mesh screen has 200 openings per linear cm

Description : Pick out the wrong statement. (A) Hammer crushers operate by impact action (B) Standard screens have circular opening (C) With increase in mesh number of screens, their diameter in microns decreases (D) 200 mesh screen has 200 openings per linear cm

Last Answer : (D) 200 mesh screen has 200 openings per linear cm

Adiabatic compression of a saturated water vapour makes it (A) Supersaturated (B) Superheated (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Adiabatic compression of a saturated water vapour makes it (A) Supersaturated (B) Superheated (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : B) Superheated

Fluid resistance to shear depends upon its (A) Rate of transfer of molecular momentum (B) Cohesion (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Fluid resistance to shear depends upon its (A) Rate of transfer of molecular momentum (B) Cohesion (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Alloy powder manufactured by the following process have spherical shapes. (A) Electrochemical deposition (B) Gaseous reduction (C) Atomisation (D) Mechanical attrition

Description : Alloy powder manufactured by the following process have spherical shapes. (A) Electrochemical deposition (B) Gaseous reduction (C) Atomisation (D) Mechanical attrition

Last Answer : (C) Atomisation

Width and speed of a conveyor belt depends upon the __________ of the material. (A) Lump size (B) Bulk density (C) Both (A) & (B) (D) Neither (A) nor (B

Description : Width and speed of a conveyor belt depends upon the __________ of the material. (A) Lump size (B) Bulk density (C) Both (A) & (B) (D) Neither (A) nor (B

Last Answer : (C) Both (A) & (B)

If the catalyst pore size is small in comparison with the mean free path, collisions with the pore wall controls the process'. The diffusivity under this condition is called 'Knudsen diffusivity', which is affected by the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : If the catalyst pore size is small in comparison with the mean free path, collisions with the pore wall controls the process'. The diffusivity under this condition is called 'Knudsen diffusivity', which is affected by the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (B) Temperature

shaft subjected to a bending moment M and a torque T, experiences (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b) (D) Neither (a) nor (b)

Description :  shaft subjected to a bending moment M and a torque T, experiences  (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b)  (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b) 

Pick up the correct statement from the following: (A) The rate of change of bending moment is equal to rate of shear force (B) The rate of change of shear force is equal to rate of loading (C) Neither (a) nor (b)(D) Both (a) and (b

Description : Pick up the correct statement from the following: (A) The rate of change of bending moment is equal to rate of shear force (B) The rate of change of shear force is equal to rate of loading (C) Neither (a) nor (b) (D) Both (a) and (b

Last Answer : (D) Both (a) and (b

When a cohesionless soil attains quick condition, it looses (A) Shear strength (B) Bearing capacity (C) Both (a) and (b) (D) Neither (a) nor (6

Description : When a cohesionless soil attains quick condition, it looses (A) Shear strength (B) Bearing capacity (C) Both (a) and (b) (D) Neither (a) nor (6

Last Answer : Answer: Option C

Factor of safety against sliding of a slope, is the ratio of (A) Actual cohesion to that required to maintain stability of slope (B) Shear strength to shear stress along the surface (C) Neither (a) nor (b) (D) Both (a) and (b)

Description : Factor of safety against sliding of a slope, is the ratio of (A) Actual cohesion to that required to maintain stability of slope (B) Shear strength to shear stress along the surface (C) Neither (a) nor (b) (D) Both (a) and (b)

Last Answer : Answer: Option D

Bond crushing law (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law (B) Is less realistic in estimating the power requirements of commercial crushers (C) States that the work required to form particle of any size from very large feed is proportional to the square root of the volume to surface ratio of the product (D) States that the work required for the crushing is proportional to the new surface created

Description : Bond crushing law (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law (B) Is less realistic in estimating the power requirements of commercial crushers ( ... (D) States that the work required for the crushing is proportional to the new surface created

Last Answer : (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law

Los Angeles testing machine is used to conduct (A) Abrasion test (B) Impact test (C) Attrition test (D) Crushing strength test

Description : Los Angeles testing machine is used to conduct (A) Abrasion test (B) Impact test (C) Attrition test (D) Crushing strength test

Last Answer : Answer: Option A

Explain the working, advantages and disadvantages of any one mill based on the principle of combined impact and attrition?

Description : Explain the working, advantages and disadvantages of any one mill based on the principle of combined impact and attrition?

Last Answer : which of the following mill works on the principle of combined impact and attrition

Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will just take hold of a particle and draw it in the crushing zone (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing (D) Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Description : Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will ... Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Last Answer : (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing

Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Description : Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Last Answer : (B) Roll crusher

Electrolytic reduction cell used for conversion of calcined Al2O3to Al is a carbon lined furnace operating at 800-900 °C. The purpose of electric current supplied to the furnace is to (A) Achieve very high purity of aluminium (99.9%) (B) Keep the electrolyte in liquid condition by the generation of heat (C) Electrolytically dissociate alumina (D) Both (B) & (C)

Description : Electrolytic reduction cell used for conversion of calcined Al2O3to Al is a carbon lined furnace operating at 800-900 °C. The purpose of electric current supplied to the furnace is to (A) Achieve very high ... by the generation of heat (C) Electrolytically dissociate alumina (D) Both (B) & (C)

Last Answer : (D) Both (B) & (C)

Shear stress is maximum at the (a) Outermost fiber (b) Central fiber (c) Neither outermost nor central fiber (d) None

Description : Shear stress is maximum at the (a) Outermost fiber (b) Central fiber (c) Neither outermost nor central fiber (d) None

Last Answer : (b) Central fiber