Tarapur (INDIA) atomic power station (A) Has two boiling water reactors of American design (B) Has an installed capacity of 400 MW (C) Is the first power reactor in India, which became critical in 1969 (D) All (A), (B) and (C)

Tarapur (INDIA) atomic power station
(A) Has two boiling water reactors of American design
(B) Has an installed capacity of 400 MW
(C) Is the first power reactor in India, which became critical in 1969
(D) All (A), (B) and (C)
by

1 Answer

Answer :

(D) All (A), (B) and (C)
by

Related questions

Bhabha Atomic Research Centre (BARC) located at Trombay (near Bombay, INDIA) has (A) Five operating research reactors (namely Apsara, Cirus Zerelina, Purnima and Dhurva) (B) A 420 MW nuclear power plant (C) A very large capacity (100 tons/yr) heavy water plant (D) All (A), (B) and (C)

Description : Bhabha Atomic Research Centre (BARC) located at Trombay (near Bombay, INDIA) has (A) Five operating research reactors (namely Apsara, Cirus Zerelina, Purnima and Dhurva) (B) A 420 MW nuclear power plant (C) A very large capacity (100 tons/yr) heavy water plant (D) All (A), (B) and (C)

Last Answer : (A) Five operating research reactors (namely Apsara, Cirus Zerelina, Purnima and Dhurva)

U-235 content in enriched uranium, that is normally used in power reactors (e.g., at Tarapur atomic power plant), is about __________ percent. (A) 85(B) 50 (C) 3 (D) 97

Description : U-235 content in enriched uranium, that is normally used in power reactors (e.g., at Tarapur atomic power plant), is about __________ percent. (A) 85 (B) 50 (C) 3 (D) 97

Last Answer : (C) 3

Nuclear power reactor located at Tarapur is of __________ type. (A) Fast breeder (B) Pressurised water (C) Boiling water (D) Gas cooled

Description : Nuclear power reactor located at Tarapur is of __________ type. (A) Fast breeder (B) Pressurised water (C) Boiling water (D) Gas cooled

Last Answer : (C) Boiling water

Which of the following is the oldest atomic power station? (a) Kalpakkam (b) Tarapur (c) Narora (d) Kota

Description : Which of the following is the oldest atomic power station? (a) Kalpakkam (b) Tarapur (c) Narora (d) Kota

Last Answer : Ans: (b)

At an industrial sub-station with a 4 MW load, a capacitor of 2 MVAR is installed to maintain the load power

Description : At an industrial sub-station with a 4 MW load, a capacitor of 2 MVAR is installed to maintain the load power factor at 0.97 lagging. If the capacitor goes out of service, the load power factor becomes (A) 0.85 (B) 1.00 (C) 0.80 lag (D) 0.90 lag

Last Answer : At an industrial sub-station with a 4 MW load, a capacitor of 2 MVAR is installed to maintain the load power factor at 0.97 lagging. If the capacitor goes out of service, the load power factor becomes  0.80 lag

Which of the following types of nuclear reactors is most prone to radioactive hazards? (A) Pressurised water reactor (B) Gas cooled reactor (C) Molten sodium cooled reactor (D) Boiling water reactor

Description : Which of the following types of nuclear reactors is most prone to radioactive hazards? (A) Pressurised water reactor (B) Gas cooled reactor (C) Molten sodium cooled reactor (D) Boiling water reactor

Last Answer : (D) Boiling water reactor

Which of the following nuclear reactors is the most efficient thermodynamically while operating between the same temperature and pressure limits of the reactor? (A) Molten sodium cooled (B) CO2 gas cooled (C) Pressurised water (D) Boiling water

Description : Which of the following nuclear reactors is the most efficient thermodynamically while operating between the same temperature and pressure limits of the reactor? (A) Molten sodium cooled (B) CO2 gas cooled (C) Pressurised water (D) Boiling water

Last Answer : (D) Boiling water

Fast breeder Test Reactor (FBTR) is located at (A) Kalpakkam (near Madras) (B) Kota (in Rajasthan) (C) BARC (Trombay) (D) Tarapur (in Maharashtra)

Description : Fast breeder Test Reactor (FBTR) is located at (A) Kalpakkam (near Madras) (B) Kota (in Rajasthan) (C) BARC (Trombay) (D) Tarapur (in Maharashtra)

Last Answer : (A) Kalpakkam (near Madras)

A generating station has a maximum demand of 50 Mw, a load factor of 60%, a plant capacity factor...

Description : A generating station has a maximum demand of 50 Mw, a load factor of 60%, a plant capacity factor of 45% and if the plant while running as per schedule, were fully loaded. The daily energy produced will be

Last Answer : A generating station has a maximum demand of 50 Mw, a load factor of 60%, a plant capacity factor of 45% and if the plant while running as per schedule, were fully loaded. The daily energy produced will be 720 MW.

Locate and label the following items on the same map with appropriate symbols. (i) Anantnag - Silk Centre (ii) Tarapur - Nuclear Power Station (iii) Raja Sansi - International Airport. -SST 10th

Description : Locate and label the following items on the same map with appropriate symbols. (i) Anantnag - Silk Centre (ii) Tarapur - Nuclear Power Station (iii) Raja Sansi - International Airport. -SST 10th

Last Answer : Outline political map of India

A Nuclear Power Station is located at (1) Kolkata (2) Tarapur (3) Korba (4) Neyveli

Description : A Nuclear Power Station is located at (1) Kolkata (2) Tarapur (3) Korba (4) Neyveli

Last Answer : Tarapur

Match the following: [CDS 1999] Atomic Power Stations States A. Kakrapara 1. Rajasthan B. Narora 2. Gujarat C. Kalpakkam 3. Tamil Nadu D. Tarapur 4. Maharashtra E. Kota 5. Uttar Pradesh A B C D E (a) 1 2 3 4 5 (b) 5 4 3 2 1 (c) 2 5 3 4 1 (d) 1 4 2 3 5

Description : Match the following: [CDS 1999] Atomic Power Stations States A. Kakrapara 1. Rajasthan B. Narora 2. Gujarat C. Kalpakkam 3. Tamil Nadu D. Tarapur 4. Maharashtra E. Kota 5. Uttar Pradesh A B C D E (a) 1 2 3 4 5 (b) 5 4 3 2 1 (c) 2 5 3 4 1 (d) 1 4 2 3 5

Last Answer : Ans: (c)

Match the following: [CDS 1999] Atomic Power Stations States A. Kakrapara 1. Rajashthan B. Narora 2. Gujarat C. Kalpakkam 3. Tamil Nadu D. Tarapur 4. Maharashtra E. Kota 5. Uttar Pradesh A B C D E (a) 1 2 3 4 5 (b) 5 4 3 2 1 (c) 2 5 3 4 1 (d) 1 4 2 3 5

Description : Match the following: [CDS 1999] Atomic Power Stations States A. Kakrapara 1. Rajashthan B. Narora 2. Gujarat C. Kalpakkam 3. Tamil Nadu D. Tarapur 4. Maharashtra E. Kota 5. Uttar Pradesh A B C D E (a) 1 2 3 4 5 (b) 5 4 3 2 1 (c) 2 5 3 4 1 (d) 1 4 2 3 5

Last Answer : Ans: (c)

Nuclear power generation capacity in India is (A) 3000 MW (B) 10000 MW (C) More than hydroelectric power generation capacity (D) More than thermal power generation capacity

Description : Nuclear power generation capacity in India is (A) 3000 MW (B) 10000 MW (C) More than hydroelectric power generation capacity (D) More than thermal power generation capacity

Last Answer : (A) 3000 MW

List any two Thermal Power Station in Maharashtra with their installed capacity.

Description : List any two Thermal Power Station in Maharashtra with their installed capacity. 

Last Answer :  Thermal Power Station in Maharashtra with their installed capacity :

For high value of diversity factor, a power station of given installed capacity will be in a position to supply?

Last Answer : For high value of diversity factor, a power station of given installed capacity will be in a position to supply more number of consumers.

Which of the following reactors is operated at high neutron flux and low power level? (A) Breeder reactor (B) Research reactor (C) Heterogeneous reactor (D) Liquid metal (e.g., molten sodium) cooled reactor

Description : Which of the following reactors is operated at high neutron flux and low power level? (A) Breeder reactor (B) Research reactor (C) Heterogeneous reactor (D) Liquid metal (e.g., molten sodium) cooled reactor

Last Answer : (B) Research reactor

A power station supplies the peak load of 60 Mw, 40 MW and 70 MW to three localities...

Description : A power station supplies the peak load of 60 Mw, 40 MW and 70 MW to three localities. The annual load factor is 0.50 p.u. and the diversity factor of the load at the station is 1.55. The maximum demand on the station and average load respectively will be 

Last Answer : A power station supplies the peak load of 60 Mw, 40 MW and 70 MW to three localities. The annual load factor is 0.50 p.u. and the diversity factor of the load at the station is 1.55. The maximum demand on the station and average load respectively will be 103.2 MW, 51.61 .

With direct water cooling it is possible to have ratings of about (a) 200 MW (b) 300 MW (c) 400 MW (d) 600 MW

Description : With direct water cooling it is possible to have ratings of about (a) 200 MW (b) 300 MW (c) 400 MW (d) 600 MW

Last Answer : (d) 600 MW

Reactors in commercial nuclear power plants in the U.S. are often referred to as thermal reactors. A thermal reactor uses: w) fissionable plutonium-239 as fuel. x) a relatively low heat output. y) neutrons moderated to relatively low energies. z) liquid sodium as a coolant.

Description : Reactors in commercial nuclear power plants in the U.S. are often referred to as thermal reactors. A thermal reactor uses: w) fissionable plutonium-239 as fuel. x) a relatively low heat output. y) neutrons moderated to relatively low energies. z) liquid sodium as a coolant.

Last Answer : ANSWER: Y -- NEUTRONS MODERATED TO RELATIVELY LOW ENERGIES.

Most of the nuclear power plants operating in the United States are: w) pressurized water reactors x) boiling water reactors y) high-temperature gas-cooled reactors z) liquid-metal fast breeder reactors

Description : Most of the nuclear power plants operating in the United States are: w) pressurized water reactors x) boiling water reactors y) high-temperature gas-cooled reactors z) liquid-metal fast breeder reactors

Last Answer : ANSWER: W -- PRESSURIZED WATER REACTORS 

. A first order irreversible reaction, A → B is carried out separately in a constant volume as well as in a variable volume reactor for a particular period. It signifies that __________ in the two reactors. (A) Both conversion as well as concentration are same (B) Conversion in both will be the same but concentrations will be different (C) Both the conversion as well as concentrations will be different (D) None of these

Description : . A first order irreversible reaction, A → B is carried out separately in a constant volume as well as in a variable volume reactor for a particular period. It signifies that __________ in the two ... be different (C) Both the conversion as well as concentrations will be different (D) None of these

Last Answer : (B) Conversion in both will be the same but concentrations will be different

For steam power plant having capacity 600 MW capacity a cooling tower is required to set up with condenser. Suggest the type of condenser and cooling tower with justification.

Description : For steam power plant having capacity 600 MW capacity a cooling tower is required to set up with condenser. Suggest the type of condenser and cooling tower with justification. 

Last Answer : For Steam power plant having Capacity 600 MW the requirement of condenser and cooling tower is as follow. 1) Condenser:- Given Capacity is medium to low capacity for this we can use Jet Condenser ... and efficiency of tower is high  -Temperature of water coming out from tower can be controlled.

N' plug flow reactors in series with a total volume 'V' gives the same conversion as a single plug flow reactor of volume 'V' for __________ order reactions. (A) First (B) Second (C) Third (D) Any

Description : N' plug flow reactors in series with a total volume 'V' gives the same conversion as a single plug flow reactor of volume 'V' for __________ order reactions. (A) First (B) Second (C) Third (D) Any

Last Answer : (D) Any

Thermal shield is used in high powered nuclear reactors to (A) Protect the walls of the reactor from radiation damageB) Absorb the fast neutrons(C) Slow down the secondary neutrons(D) Protect the fuel element from coming in contact with the coolant

Description : Thermal shield is used in high powered nuclear reactors to (A) Protect the walls of the reactor from radiation damage B) Absorb the fast neutrons (C) Slow down the secondary neutrons (D) Protect the fuel element from coming in contact with the coolant

Last Answer : (A) Protect the walls of the reactor from radiation damage

In flow reactors, the performance equations interrelate the rate of reaction to the (A) Feed rate (B) Reactor volume (C) Extent of reaction (D) All (A), (B) and (C)

Description : In flow reactors, the performance equations interrelate the rate of reaction to the (A) Feed rate (B) Reactor volume (C) Extent of reaction (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

For an autocatalytic reactor, the suitable reactor set up is(A) P.F. reactors in series (B) CSTR in series (C) CSTR followed by P.F. reactor (D) P.F. reactor followed by CSTR

Description : For an autocatalytic reactor, the suitable reactor set up is (A) P.F. reactors in series (B) CSTR in series (C) CSTR followed by P.F. reactor (D) P.F. reactor followed by CSTR

Last Answer : (C) CSTR followed by P.F. reactor

Pick out the wrong statement pertaining to space velocity of flow reactors. (A) The unit of space velocity is (time) -1 (B) The space velocity of 3 hr -1 means that three reactor volumes of feed at specified conditions are being fed into the reactor every hour (C) The space velocity of 3 hr -1 means that one third reactor volume of feed at specified conditions are being fed into the reactor (D) None of these

Description : Pick out the wrong statement pertaining to space velocity of flow reactors. (A) The unit of space velocity is (time) -1 (B) The space velocity of 3 hr -1 means that three reactor volumes of ... one third reactor volume of feed at specified conditions are being fed into the reactor (D) None of these

Last Answer : (C) The space velocity of 3 hr -1 means that one third reactor volume of feed at specified conditions are being fed into the reactor

With the same reaction time, initial concentration and feed rate, the reaction 2A → B is carried out separately in CSTR and P.F. reactor of equal volumes. The conversion will be (A) Higher in P.F. reactor (B) Higher in CSTR (C) Same in both the reactors (D) Data insufficient; can't be predicted

Description : With the same reaction time, initial concentration and feed rate, the reaction 2A → B is carried out separately in CSTR and P.F. reactor of equal volumes. The conversion will be (A) Higher in P.F. reactor (B) Higher in CSTR (C) Same in both the reactors (D) Data insufficient; can't be predicted

Last Answer : (A) Higher in P.F. reactor

In a substation the following equipment is not installed (a) exciters (b) series capacitors (c) shunt reactors (d) voltatre transformers

Description : In a substation the following equipment is not installed (a) exciters (b) series capacitors (c) shunt reactors (d) voltatre transformers

Last Answer : (a) exciters

A generating station has a maximum demand of 500 MW. The annual load factor is 50 percent. The energy

Description : A generating station has a maximum demand of 500 MW. The annual load factor is 50 percent. The energy generated per annum will be: A) 2.19 x 106 MWhr B) 600 MWhr C) 250 MWhr D) 7.50 x 106 MWhr

Last Answer : A generating station has a maximum demand of 500 MW. The annual load factor is 50 percent. The energy generated per annum will be: 2.19 x 106 MWhr 

A generating station has a maximum demand of 30 MW, a load factor of 60% and a plant

Description : A generating station has a maximum demand of 30 MW, a load factor of 60% and a plant capacity factor of 50%. The reserve capacity of the plant is   (a) 5 MW (b) 4 MW (c) 6 MW (d) 10 MW 

Last Answer : A generating station has a maximum demand of 30 MW, a load factor of 60% and a plant capacity factor of 50%. The reserve capacity of the plant is 6 MW

Graphite is used in nuclear reactors for- (1) reducing the speed of fast neutrons (2) cooling the reactor (3) absorbing neutrons (4) None of the above

Description : Graphite is used in nuclear reactors for- (1) reducing the speed of fast neutrons (2) cooling the reactor (3) absorbing neutrons (4) None of the above

Last Answer : (1) reducing the speed of fast neutrons Explanation: A graphite reactor is a nuclear reactor that uses carbon as a neutron moderator, which allows unenriched uranium to be used as nuclear fuel.

In Nuclear reactors graphite is used as (1) Lubricant (2) Fuel (3) Linear of the reactor (4) Modulator

Description : In Nuclear reactors graphite is used as (1) Lubricant (2) Fuel (3) Linear of the reactor (4) Modulator

Last Answer : (4) Modulator Explanation: Nuclear reactors are used at nuclear power plants for electricity generation. These are generally graphite moderated and CO2 cooled.

_________ nuclear reactor does not require a heat exchanger tosupply steam to power turbine.(A) Molten sodium cooled(B) Helium cooled(C) Boiling water(D) Pressurised water

Description : _________ nuclear reactor does not require a heat exchanger tosupply steam to power turbine. (A) Molten sodium cooled (B) Helium cooled (C) Boiling water (D) Pressurised water

Last Answer : (C) Boiling water

The nuclear power plant in India which will provide power mainly for agriculture is located at (a) Kalpakkam (b) Narora (c) Kota (d) Tarapur

Description : The nuclear power plant in India which will provide power mainly for agriculture is located at (a) Kalpakkam (b) Narora (c) Kota (d) Tarapur

Last Answer : Ans: (b)

The voltage at the two ends of a transmission line are 132 KV and its reactance is 40 ohm. The Capacity of the line is (A) 435.6 MW (B) 217.8 MW (C) 251.5 MW (D) 500 MW

Description : The voltage at the two ends of a transmission line are 132 KV and its reactance is 40 ohm. The Capacity of the line is (A) 435.6 MW (B) 217.8 MW (C) 251.5 MW (D) 500 MW

Last Answer : (A) 435.6 MW

To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length of the pipe is 1506 m and f = 0.01, ignoring other minor losses and assuming the economical diameter from Lea's formula D = 1.2 Q, the water horse power of the pump is (A) 400 (B) 450 (C) 500(D) 600

Description : To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is  installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length  of the ... the water horse power of the pump is  (A) 400  (B) 450  (C) 500 (D) 600

Last Answer : (D) 600

The oldest nuclear power plant at Tarapur is located on the border between (a) Maharashtra and Karnataka (b) Karnataka and Andhra Pradesh (c) Maharashtra and Gujarat (d) Gujarat and Rajasthan

Description : The oldest nuclear power plant at Tarapur is located on the border between (a) Maharashtra and Karnataka (b) Karnataka and Andhra Pradesh (c) Maharashtra and Gujarat (d) Gujarat and Rajasthan

Last Answer : Ans: (c)

Write a note on atomic reactors in India.

Description : Write a note on atomic reactors in India.

Last Answer : a) Bhabha Atomic Research Centre [BARC] has been setup for research and development work in atomic energy. b) Tarapur [Maharashtra] atomic power station was the first to be setup in India [1969]. c) Kota [Rajasthan] d) Kalpakam [Tamil Nadu] e) Kaiga [ Karnataka]

What did the Soviets want American when Nixon took office in 1969?

Description : What did the Soviets want American when Nixon took office in 1969?

Last Answer : food to make up for shortages

The isotope of Uranium used in atomic reactors is – (1) U^235 (2) (2) U^236 (3) U^237 (4) U^232

Description : The isotope of Uranium used in atomic reactors is – (1) U^235 (2) (2) U^236 (3) U^237 (4) U^232

Last Answer : (1) U^235 Explanation: A nuclear reactor is a device to initiate and control a sustained nuclear chain reaction. Most commonly they are used for generating electricity and for the propulsion of ships ... fissile atomic nucleus such as U235 or U239 absorbs a neutron, it may undergo nuclear fission.

The sodium compound used as coolant in atomic reactors?

Description : The sodium compound used as coolant in atomic reactors?

Last Answer : Liquid sodium

One of the following countries produces maximum energy from atomic reactors? A. France (80% from its Nuclear Reactors) B. USA C. UK

Description : One of the following countries produces maximum energy from atomic reactors? A. France (80% from its Nuclear Reactors) B. USA C. UK

Last Answer : A. France (80% from its Nuclear Reactors)

Coolant used in a boiling water reactor is (A) Hydrogen gas (B) Water (C) Steam (D) A mixture of water & steam

Description : Coolant used in a boiling water reactor is (A) Hydrogen gas (B) Water (C) Steam (D) A mixture of water & steam

Last Answer : (D) A mixture of water & steam

A boiling water reactor is the one, in which the (A) Coolant water is allowed to boil in the core of the reactor (B) Coolant water, after being heated in the reactor core, generates steam in a boiler (C) Pressurised water is pumped into the core (D) Fuel and the coolant are thoroughly mixed to form a homogeneous solution

Description : A boiling water reactor is the one, in which the (A) Coolant water is allowed to boil in the core of the reactor (B) Coolant water, after being heated in the reactor core, generates steam ... water is pumped into the core (D) Fuel and the coolant are thoroughly mixed to form a homogeneous solution

Last Answer : (A) Coolant water is allowed to boil in the core of the reactor

In a pressurised water reactor (PWR), the (A) Fuel is natural uranium and heavy water acts both as moderator & coolant (B) Coolant water boils in the core of the reactor (C) Coolant water is pressurised to prevent bulk boiling of water in the core (D) Use of moderator is not required

Description : In a pressurised water reactor (PWR), the (A) Fuel is natural uranium and heavy water acts both as moderator & coolant (B) Coolant water boils in the core of the reactor (C) Coolant water is pressurised to prevent bulk boiling of water in the core (D) Use of moderator is not required

Last Answer : (C) Coolant water is pressurised to prevent bulk boiling of water in the core

Nuclear fuel usually used in a Boiling Water Reactor (BWR) is (A) Plutonium (B) Enriched uranium (C) Natural uranium (D) Thorium

Description : Nuclear fuel usually used in a Boiling Water Reactor (BWR) is (A) Plutonium (B) Enriched uranium (C) Natural uranium (D) Thorium

Last Answer : (B) Enriched uranium

The most commonly used nuclear fuel in boiling water reactor is (A) Enriched uranium (B) Natural uranium (C) Plutonium

Description : The most commonly used nuclear fuel in boiling water reactor is (A) Enriched uranium (B) Natural uranium (C) Plutonium

Last Answer : (A) Enriched uranium

Heavy water is used as a moderator in a (A) Pressurised water reactor (PWR) (B) Boiling water reactor (BWR) (C) Candu reactor (D) Molten sodium cooled reactor

Description : Heavy water is used as a moderator in a (A) Pressurised water reactor (PWR) (B) Boiling water reactor (BWR) (C) Candu reactor (D) Molten sodium cooled reactor

Last Answer : (C) Candu reactor