Absolute vapor pressure of petrofuels is found by Reid bomb which is heated in water bath to 100°F. In Reid apparatus, the ratio of the volume of air chamber to that of the liquid fuel chamber is (A) 4 (B) 3 (C) 2 (D) 1

Absolute vapor pressure of petrofuels is found by Reid bomb which is
heated in water bath to 100°F. In Reid apparatus, the ratio of the volume of
air chamber to that of the liquid fuel chamber is
(A) 4
(B) 3
(C) 2
(D) 1
by

1 Answer

Answer :

(A) 4
by

Related questions

Pick out the wrong statement. (A) Aromatics have higher specific gravity than paraffins (B) Gross calorific value (GCV) of petrofuels is equal to (12400 - 2100 ρ 2 ) where, ρ is the specific gravity of the fuel at 15.5°C (C) Heavier petrofuels have higher GCV on weight basis (i.e., Kcal/kg) but lower GCV on volume basis (i.e., Kcal/litre) (D) Higher specific gravity of petrofuels means higher C/H ratio

Description : Pick out the wrong statement. (A) Aromatics have higher specific gravity than paraffins (B) Gross calorific value (GCV) of petrofuels is equal to (12400 - 2100 ρ 2 ) where, ρ is the specific gravity ... volume basis (i.e., Kcal/litre) (D) Higher specific gravity of petrofuels means higher C/H ratio

Last Answer : (C) Heavier petrofuels have higher GCV on weight basis (i.e., Kcal/kg) but lower GCV on volume basis (i.e., Kcal/litre)

Liquid "X" is at equilibrium with its vapor in a cylinder and piston apparatus. When the volume of the space above the liquid is 50 ml and the temperature 25!, the vapor pressure of "X" is 120 torr. What will the vapor pressure of "X" be when the volume above the liquid is 100 ml and the temperature 25!C? Some liquid is always present. w) 30 torr x) 60 torr y) 120 torr z) 240 torr

Description : Liquid "X" is at equilibrium with its vapor in a cylinder and piston apparatus. When the volume of the space above the liquid is 50 ml and the temperature 25!, the vapor pressure of "X" is 120 torr. What will the ... 25!C? Some liquid is always present. w) 30 torr x) 60 torr y) 120 torr z) 240 torr

Last Answer : ANSWER: Y -- 120 TORR

__________ determination is not a very significant and important test for gasoline. (A) Gum & sulphur content (B) Viscosity (C) Octane number (D) Reid vapor pressure

Description : __________ determination is not a very significant and important test for gasoline. (A) Gum & sulphur content (B) Viscosity (C) Octane number (D) Reid vapor pressure

Last Answer : (B) Viscosity

Testing of the knocking characteristics of petrofuels is done in a __________ engine. (A) Carnot (B) CFR (Co-operative fuel research) (C) Stirling (D) Diesel

Description : Testing of the knocking characteristics of petrofuels is done in a __________ engine. (A) Carnot (B) CFR (Co-operative fuel research) (C) Stirling (D) Diesel

Last Answer : (B) CFR (Co-operative fuel research)

Turndown ratio of a burner gives an idea of the __________ in the furnace. (A) Range of fuel firing rates (B) Volume of the combustion chamber (C) Maximum heat input rate only (D) Minimum heat input rate only

Description : Turndown ratio of a burner gives an idea of the __________ in the furnace. (A) Range of fuel firing rates (B) Volume of the combustion chamber (C) Maximum heat input rate only (D) Minimum heat input rate only

Last Answer : (A) Range of fuel firing rates

In case of liquid petrofuels, momentary combustion is observed at its (A) Flash point (B) Preheating temperature corresponding to viscosity of 25 centistokes (C) Flame temperature (D) Fire point

Description : In case of liquid petrofuels, momentary combustion is observed at its (A) Flash point (B) Preheating temperature corresponding to viscosity of 25 centistokes (C) Flame temperature (D) Fire point

Last Answer : (A) Flash point

With increase in absolute humidity, the dew point of an unsaturated mixture of air and water vapor (at constant pressure and temperature). (A) Increases (B) Remains unchanged (C) Decreases (D) Decreases linearly

Description : With increase in absolute humidity, the dew point of an unsaturated mixture of air and water vapor (at constant pressure and temperature). (A) Increases (B) Remains unchanged (C) Decreases (D) Decreases linearly

Last Answer : (A) Increases

Dryness factor of steam is defined as the ratio of the mass of vapor in the mixture to the mass of the mixture. Dryness factor of steam is measured by a __________ calorimeter. (A) Bomb (B) Throttling (C) Junker's (D) Boy's

Description : Dryness factor of steam is defined as the ratio of the mass of vapor in the mixture to the mass of the mixture. Dryness factor of steam is measured by a __________ calorimeter. (A) Bomb (B) Throttling (C) Junker's (D) Boy's

Last Answer : Option B

Vapour lock is a. complete or partial stoppage of fuel supply due to vaporization of the fuel b. locking of carburetor due to high vapor pressure c. excess fuel supply to the engine d. supply of liquid fuel to the engine

Description : Vapour lock is a. complete or partial stoppage of fuel supply due to vaporization of the fuel b. locking of carburetor due to high vapor pressure c. excess fuel supply to the engine d. supply of liquid fuel to the engine

Last Answer : ANSWER a. complete or partial stoppage of fuel supply due to vaporization of the fuel

The time taken for gravity flow of a fixed volume of liquid (as in Redwood viscometer) is directly proportional to its (A) Absolute viscosity (B) Ratio of absolute viscosity to density (C) Density (D) Reynolds number

Description : The time taken for gravity flow of a fixed volume of liquid (as in Redwood viscometer) is directly proportional to its (A) Absolute viscosity (B) Ratio of absolute viscosity to density (C) Density (D) Reynolds number

Last Answer : (B) Ratio of absolute viscosity to density

What pressure does ASME B16.5 limit flanged fittings to during system hydrostatic testing? a) 1.5 times the 100°F pressure rating, rounded to next highest 25psi. b) 1.5 times the flange class. c) The maximum pressure rating for the flange. d) The flange class plus 250psi.

Description : What pressure does ASME B16.5 limit flanged fittings to during system hydrostatic testing? a) 1.5 times the 100°F pressure rating, rounded to next highest 25psi. b) 1.5 times the flange class. c) The maximum pressure rating for the flange. d) The flange class plus 250psi.

Last Answer : a) 1.5 times the 100°F pressure rating, rounded to next highest 25psi. b) 1.5 times the flange class.

Relative volatility varies with the concentration of component for an ideal solution. The relative volatility of a binary mixture may be defined as the ratio of vapor pressure of component 'A' to that of component 'B', when (A) Only vapor phase follows Raoult's law (B) Only liquid phase obeys Dalton's law (C) Liquid phase obeys Dalton's law and vapor phase obeys Raoult's law (D) Vapor phase obeys Dalton's law and liquid phase obeys Raoult's law

Description : Relative volatility varies with the concentration of component for an ideal solution. The relative volatility of a binary mixture may be defined as the ratio of vapor pressure of component 'A' to that of ... law (D) Vapor phase obeys Dalton's law and liquid phase obeys Raoult's law

Last Answer : (D) Vapor phase obeys Dalton's law and liquid phase obeys Raoult's law

Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for counter flow and parallel flow can be theoretically same when any one of the fluids (hot or cold fluid) passes through the heat exchanger at constant temperature (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs (D) Phase change in case of a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Description : Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for ... a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Last Answer : (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs

_________is the partial pressure of water vapor at the existing temperature divided by the equilibrium vapor pressure of water at the existing temperature.  a. vacuum pressure  b. relative humidity  c. absolute pressure  d. vapor pressure

Description : _________is the partial pressure of water vapor at the existing temperature divided by the equilibrium vapor pressure of water at the existing temperature.  a. vacuum pressure  b. relative humidity  c. absolute pressure  d. vapor pressure

Last Answer : relative humidity

Which of the following is Clausius-Clapeyron Equation for vaporisation of an ideal gas under the condition that the molar volume of liquid is negligible compared to that of the vapor? (A) d ln p/dt = Hvap/RT2 (B) d ln p/dt = RT2/Hvap (C) dp/dt = RT2/Hvap (D) dp/dt = Hvap/RT2

Description : Which of the following is Clausius-Clapeyron Equation for vaporisation of an ideal gas under the condition that the molar volume of liquid is negligible compared to that of the vapor? (A) d ln p/dt = Hvap/RT2 (B) d ln p/dt = RT2/Hvap (C) dp/dt = RT2/Hvap (D) dp/dt = Hvap/RT2

Last Answer : (A) d ln p/dt = Hvap/RT2

Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Description : Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In reverberatory furnace, charge is heated mainly by (A) Conduction (B) Natural convection (C) Radiation of heat from the roof of the combustion chamber (D) None of these

Description : In reverberatory furnace, charge is heated mainly by (A) Conduction (B) Natural convection (C) Radiation of heat from the roof of the combustion chamber (D) None of these

Last Answer : (C) Radiation of heat from the roof of the combustion chamber

Reid vapour pressure of gasoline is the measure of its (A) Pour point (B) Cloud point (C) Vapour locking tendency (D) Carbon residue

Description : Reid vapour pressure of gasoline is the measure of its (A) Pour point (B) Cloud point (C) Vapour locking tendency (D) Carbon residue

Last Answer : (C) Vapour locking tendency

Higher viscosity of lubricating oil usually signifies (A) Lower Reid vapour pressure (B) Higher acid number (C) Higher flash point and fire point (D) Lower flash point and fire point

Description : Higher viscosity of lubricating oil usually signifies (A) Lower Reid vapour pressure (B) Higher acid number (C) Higher flash point and fire point (D) Lower flash point and fire point

Last Answer : (C) Higher flash point and fire point

True vapour pressure of a petroleum fraction __________ Reid vapour pressure. (A) Is less than (B) Is more than (C) Is same as (D) May be either more or less than

Description : True vapour pressure of a petroleum fraction __________ Reid vapour pressure. (A) Is less than (B) Is more than (C) Is same as (D) May be either more or less than

Last Answer : (D) May be either more or less than

Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion (B) Nitrogen percentage in the fuel is very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Description : Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion ... very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Last Answer : (C) Excess air has been used for combustion

Initial pressure of oxygen introduced into the 'bomb' of the bomb calorimeter for determination of calorific value of coal/fuel oil may be around __________ atm. (A) 3-5 (B) 25-30 (C) 60-65 (D) 95-100

Description : Initial pressure of oxygen introduced into the 'bomb' of the bomb calorimeter for determination of calorific value of coal/fuel oil may be around __________ atm. (A) 3-5 (B) 25-30 (C) 60-65 (D) 95-100

Last Answer : (B) 25-30

Which of the following temperatures represents the maximum allowable temperature for the electrolyte of a lead-acid battery? A. 100°F B. 125°F C. 145°F D. 212°F

Description : Which of the following temperatures represents the maximum allowable temperature for the electrolyte of a lead-acid battery? A. 100°F B. 125°F C. 145°F D. 212°F

Last Answer : Answer: B

What is the maximum temperature for hydrostatic testing per ASME B16.5? a) 70°F b) 100°F c) 125°F d) 200°F

Description : What is the maximum temperature for hydrostatic testing per ASME B16.5? a) 70°F b) 100°F c) 125°F d) 200°F

Last Answer : c) 125°F

How To Make A Bath Bomb Recipes

Description : How To Make A Bath Bomb Recipes

Last Answer : Recipe 1 Mix 1 part citric acid (you can get this at a pharmacy) 2 1/4 parts baking soda Add several drops of essential oil and a few drops food coloring Moisten by spraying with water or witch hazel ( ... its own candy cup. Store bombs in a closed container. To use drop, 1 -3 into warm bath water

A vessel with a volume of cubic meter contains liquid water and water vapor ion equilibrium at 600 kPa. The liquid water has mass of1kg. Using the steam table, calculate the mass of the water vapor.  A. 0.99kg  B. 1.57 kg  C. 2.54 kg  D. 3.16 kg Formula: from the steam table at 600kPa vƒ = 0.001101 m^3 / kg vg = 0.3157 m^3 / kg Vtot = mƒ vƒ + mg vg mg = (tot-mƒ vƒ) / vg

Description : A vessel with a volume of cubic meter contains liquid water and water vapor ion equilibrium at 600 kPa. The liquid water has mass of1kg. Using the steam table, calculate the mass of the water vapor.  A. 0.99kg  B. 1.57 kg  C ... / kg vg = 0.3157 m^3 / kg Vtot = mƒ vƒ + mg vg mg = (tot-mƒ vƒ) / vg

Last Answer : 3.16 kg

As the reflux ratio in a distillation column is increased from the minimum, the (A) Slope of the operating line in stripping section decreases (B) Number of plates decreases very slowly first and then more and more rapidly (C) Total cost first decreases and then increases (D) Liquid flow increases while the vapor flow decreases for a system

Description : As the reflux ratio in a distillation column is increased from the minimum, the (A) Slope of the operating line in stripping section decreases (B) Number of plates decreases very slowly first ... decreases and then increases (D) Liquid flow increases while the vapor flow decreases for a system

Last Answer : (C) Total cost first decreases and then increases

Amount of water vapour (gaseous) in a given volume of air (cubic metre) is known as: (1) Mixing ratio (2) Relative humidity (3) Absolute humidity (4) Specific humidity

Description : Amount of water vapour (gaseous) in a given volume of air (cubic metre) is known as: (1) Mixing ratio (2) Relative humidity (3) Absolute humidity (4) Specific humidity

Last Answer : (3) Absolute humidity Explanation: The relative humidity of air at a given temperature is the ratio of mass of water vapour actually present in a certain volume of air to the mass of water vapour required to saturate the same volume of air at the same temperature, multiplied by 100.

Amount of water vapour in a unit volume (Cubic metre) of air is called: (1) Mixed ratio (2) relative humidity (3) absolute humidity (4) specific humidity

Description : Amount of water vapour in a unit volume (Cubic metre) of air is called: (1) Mixed ratio (2) relative humidity (3) absolute humidity (4) specific humidity

Last Answer : (3) absolute humidity Explanation: Absolute humidity is the measure of water vapor (moisture) in the air, regardless of temperature. It is expressed as grams of moisture per cubic meter of air (g/m3).

Amount of water vapour (gaseous) in a given volume of air (cubic metre) is known as: (1) Mixing ratio (2) Relative humidity (3) Absolute humidity (4) Specific humidity

Description : Amount of water vapour (gaseous) in a given volume of air (cubic metre) is known as: (1) Mixing ratio (2) Relative humidity (3) Absolute humidity (4) Specific humidity

Last Answer : Absolute humidity

Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) Requirement of large volume combustion chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Description : Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) ... chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Last Answer : (B) Risk of explosion

Pick out the wrong statement. (A) Cp of monatomic gases such as metallic vapor is about 5 kcal/kg.atom (B) The heat capacity of solid inorganic substance is exactly equal to the heatcapacity of the substance in the molten state(C) There is an increase in entropy, when a spontaneous change occurs in anisolated system(D) At absolute zero temperature, the heat capacity for many pure crystallinesubstances is zero

Description : Pick out the wrong statement. (A) Cp of monatomic gases such as metallic vapor is about 5 kcal/kg.atom (B) The heat capacity of solid inorganic substance is exactly equal to the ... isolated system (D) At absolute zero temperature, the heat capacity for many pure crystalline substances is zero

Last Answer : (C) There is an increase in entropy, when a spontaneous change occurs in an isolated system

Pick up the correct statement from the following: (A) Absolute humidity at a given temperature is equal to weight of moisture present in a unit volume (B) Relative humidity is the ratio of actual vapour pressure and saturation vapour pressure at the same temperature (C) Relative humidity is the ratio of the weight of the vapours present per unit volume to the weight of vapours which could be contained at the same temperature when fully saturated (D) All the above

Description : Pick up the correct statement from the following: (A) Absolute humidity at a given temperature is equal to weight of moisture present in a unit volume (B) Relative humidity is the ratio of ... of vapours which could be contained at the same temperature when fully saturated (D) All the above

Last Answer : Answer: Option D

In a 4 S diesel engine, the term ‘squish’ refers to the (a) Injection of fuel in the precombustion chamber (b) Discharge of gases from the precombustion chamber (c) Entry of air into the combustion chamber (d) Stripping of fuel from the core

Description : In a 4 S diesel engine, the term ‘squish’ refers to the (a) Injection of fuel in the precombustion chamber (b) Discharge of gases from the precombustion chamber (c) Entry of air into the combustion chamber (d) Stripping of fuel from the core

Last Answer : Ans :c

Bomb calorimeter is used to determine the (where, GCV - Gross Calorific Value. NCV - Net Calorific Value.) (A) GCV at constant pressure (B) GCV at constant volume (C) NCV at constant pressure (D) NCV at constant volume

Description : Bomb calorimeter is used to determine the (where, GCV - Gross Calorific Value. NCV - Net Calorific Value.) (A) GCV at constant pressure (B) GCV at constant volume (C) NCV at constant pressure (D) NCV at constant volume

Last Answer : (C) NCV at constant pressure

Calorific value as determined by bomb calorimeter is the (A) Higher calorific value at constant volume(B) Gross calorific value at constant pressure(C) Lower calorific value at constant pressure(D) Net calorific value at constant volume

Description : Calorific value as determined by bomb calorimeter is the (A) Higher calorific value at constant volume (B) Gross calorific value at constant pressure (C) Lower calorific value at constant pressure (D) Net calorific value at constant volume

Last Answer : (A) Higher calorific value at constant volume

Which of these is an output of a ‘Furnace’? a. Fuel gas b. Cool Air c. Flue gases d. Water Vapor

Description : Which of these is an output of a ‘Furnace’? a. Fuel gas b. Cool Air c. Flue gases d. Water Vapor

Last Answer : c. Flue gases

__________ is the temperature at which a gas-vapor mixture becomes saturated, when cooled at constant total pressure out of contact with a liquid. (A) Dew point (B) Bubble point (C) Dry bulb temperature (D) Wet bulb temperature

Description : __________ is the temperature at which a gas-vapor mixture becomes saturated, when cooled at constant total pressure out of contact with a liquid. (A) Dew point (B) Bubble point (C) Dry bulb temperature (D) Wet bulb temperature

Last Answer : (A) Dew point

If a two phase system is in physical equilibrium; then it means that, the(A) Escaping tendency of each component from the liquid phase to the vaporphase is exactly equal to that from vapor phase to liquid phase(B) Temperature of the liquid phase is equal to that of the vapor phase(C) Total pressure throughout the liquid phase is equal to that throughout thevapor phase(D) All (A), (B) and (C)

Description : If a two phase system is in physical equilibrium; then it means that, the (A) Escaping tendency of each component from the liquid phase to the vapor phase is exactly equal to that from vapor phase to liquid phase ... liquid phase is equal to that throughout the vapor phase (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In an operating distillation column, the (A) Vapors and liquids are at their dew point and bubble point respectively (B) Driving force for the liquid flow is its specific weight (C) Driving force for the vapor flow is the pressure drop, as the pressure decreases gradually from the bottom to the top of the column (D) Highest temperature is encountered at the top of the column

Description : In an operating distillation column, the (A) Vapors and liquids are at their dew point and bubble point respectively (B) Driving force for the liquid flow is its specific weight (C) Driving force for ... bottom to the top of the column (D) Highest temperature is encountered at the top of the column

Last Answer : (C) Driving force for the vapor flow is the pressure drop, as the pressure decreases gradually from the bottom to the top of the column

Flooding in a vapor-liquid contacting equipment occurs in a tray, when the pressure drop through a tray is __________ the liquid head available in the downcomer. (A) Less than (B) More than (C) Same as (D) Very much less

Description : Flooding in a vapor-liquid contacting equipment occurs in a tray, when the pressure drop through a tray is __________ the liquid head available in the downcomer. (A) Less than (B) More than (C) Same as (D) Very much less

Last Answer : (B) More than

Bound moisture is that liquid which exerts an equilibrium vapor pressure __________ that of the pure liquid at the given temperature. (A) Less than (B) More than (C) Equal to (D) Either (A) or (B); depends on the solid

Description : Bound moisture is that liquid which exerts an equilibrium vapor pressure __________ that of the pure liquid at the given temperature. (A) Less than (B) More than (C) Equal to (D) Either (A) or (B); depends on the solid

Last Answer : (A) Less than

Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a shell and tube heat exchanger (C) Steam jet ejector is used for vapor compression in a thermal recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Description : Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a ... recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Last Answer : (D) Heat sensitive materials should be concentrated in high pressure evaporators

The actual temperature drop across the heating surface of an evaporator depends on the (A) Liquid depth over the heating surface (B) Solution being evaporated (C) Pressure difference between the steam chest and the vapor space above the boiling liquid (D) All (A), (B) and (C)

Description : The actual temperature drop across the heating surface of an evaporator depends on the (A) Liquid depth over the heating surface (B) Solution being evaporated (C) Pressure difference between the steam chest and the vapor space above the boiling liquid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation (B) Cavitation may be caused due to boiling of liquid by decreasing the pressure resulting in formation & collapse of vapor cavities (C) Cavitation begins at higher static pressure and lower velocity in larger diameter pipelines resulting in audible noise(D) Large scale cavitation cannot damage pipeline, restrict fluid flow anddamage steam turbine blades

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor pressure of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature

The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor pressure of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Description : The net positive suction head (NPSH) of a centrifugal pump is defined as the sum of the velocity head and the pressure head at the (A) Discharge (B) Suction (C) Suction minus vapor ... of the liquid at suction temperature (D) Discharge minus vapor pressure of the liquid at the discharge temperature

Last Answer : (C) Suction minus vapor pressure of the liquid at suction temperature

In centrifugal pumps, cavitation occurs, when pressure of the impeller eye or vane becomes (A) Less than atmospheric pressure (B) More than liquid vapor pressure (C) Less than liquid vapor pressure (D) More than atmospheric pressure

Description : In centrifugal pumps, cavitation occurs, when pressure of the impeller eye or vane becomes (A) Less than atmospheric pressure (B) More than liquid vapor pressure (C) Less than liquid vapor pressure (D) More than atmospheric pressure

Last Answer : (C) Less than liquid vapor pressure

Boiling of liquid is accompanied with increase in the (A) Vapor pressure (B) Specific Gibbs free energy (C) Specific entropy (D) All (A), (B) and (C)

Description : Boiling of liquid is accompanied with increase in the (A) Vapor pressure (B) Specific Gibbs free energy (C) Specific entropy (D) All (A), (B) and (C)

Last Answer : (A) Vapor pressure

A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co-efficient and fi° is the fugacity of the pure component i. the Ki value (Yi = Ki xi) is therefore, in general a function of (A) Temperature only (B) Temperature and pressure only (C) Temperature, pressure and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Description : A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co- ... and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Last Answer : (C) Temperature, pressure and liquid composition xi only