The difference between the original and reconstructed signal gives rise to A. S factor B. Quantizing noise C. S/N D. Fade margin

The difference between the original and reconstructed signal gives rise to
A. S factor
B. Quantizing noise
C. S/N
D. Fade margin
by

1 Answer

Answer :

B. Quantizing noise
by

Related questions

Noise occurring in the presence of signal resulting from a mismatch between the exact value of an analog signal and the closet available quantizing step in a digital coder. A. Quantizing noise B. Thermal noise C. Impulse noise D. Crosstalk

Description : Noise occurring in the presence of signal resulting from a mismatch between the exact value of an analog signal and the closet available quantizing step in a digital coder. A. Quantizing noise B. Thermal noise C. Impulse noise D. Crosstalk

Last Answer : A. Quantizing noise

What is the reliable measurement for comparing amplifier noise characteristics? A. Thermal agitation noise B. Noise factor C. Noise margin D. Signal-to-noise

Description : What is the reliable measurement for comparing amplifier noise characteristics? A. Thermal agitation noise B. Noise factor C. Noise margin D. Signal-to-noise

Last Answer : B. Noise factor

What is the difference between available power and power budget? A. Power margin B. Extra power C. Fade margin D. System gain

Description : What is the difference between available power and power budget? A. Power margin B. Extra power C. Fade margin D. System gain

Last Answer : A. Power margin

_______ is referred as the difference between available power and power budget? A. Fade margin B. Power margin C. Nominal gain D. Power dissipation

Description : _______ is referred as the difference between available power and power budget? A. Fade margin B. Power margin C. Nominal gain D. Power dissipation

Last Answer : B. Power margin

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise

Description : Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise

Last Answer : D. Miscellaneous noise

Noise that occurs via capacitive or inductive coupling in a cable. A. Crosstalk B. Quantizing noise C. Reference noise D. Tone interference

Description : Noise that occurs via capacitive or inductive coupling in a cable. A. Crosstalk B. Quantizing noise C. Reference noise D. Tone interference

Last Answer : A. Crosstalk

Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Description : Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Last Answer : C. Impulse noise

Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Description : Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk

Last Answer : A. Quantizing noise

Quantizing noise occurs in A. PCM B. PLM C. PDM D. PAM

Description : Quantizing noise occurs in A. PCM B. PLM C. PDM D. PAM

Last Answer : A. PCM

What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion

Description : What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion

Last Answer : D. To protect small signals in PCM from quantizing distortion

Which does not effect noise in a channel? A. None of these B. Bandwidth C. Temperature D. Quantizing level

Description : Which does not effect noise in a channel? A. None of these B. Bandwidth C. Temperature D. Quantizing level

Last Answer : D. Quantizing level

Steps to follow to produce PCM signal. A. Quantizing, sampling, and coding B. Sampling, quantizing, and coding C. Sampling, coding and quantizing D. Coding, quantizing and coding

Description : Steps to follow to produce PCM signal. A. Quantizing, sampling, and coding B. Sampling, quantizing, and coding C. Sampling, coding and quantizing D. Coding, quantizing and coding

Last Answer : B. Sampling, quantizing, and coding

Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Description : Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Last Answer : A. 5.23 dB

The difference between the original and reconstructed data, which we will refer to as the ______in the reconstructed data. a. Redundancy b. Compression c. loss d. Distortion

Description : The difference between the original and reconstructed data, which we will refer to as the ______in the reconstructed data. a. Redundancy b. Compression c. loss d. Distortion

Last Answer : d. Distortion

The process of assigning PCM codes to absolute magnitudes A. Overloading B. All of these C. Quantizing D. Multiplexing

Description : The process of assigning PCM codes to absolute magnitudes A. Overloading B. All of these C. Quantizing D. Multiplexing

Last Answer : C. Quantizing

In order to reduce quantizing noise, one must

Last Answer : In order to reduce quantizing noise, one must Increase the number of standard amplitudes.

Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Last Answer : A. increases sensitivity to weak signals

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Last Answer : C. In the receiver front end

Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Description : Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Last Answer : D. high

Unwanted radio signal on assigned frequency. A. Splatter B. RFI C. Noise D. EMI

Description : Unwanted radio signal on assigned frequency. A. Splatter B. RFI C. Noise D. EMI

Last Answer : C. Noise

Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Description : Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Last Answer : B. The approximation of the quantized signal

Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Description : Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Last Answer : The approximation of the quantized signal

Noise always affects the signal in a communications systems at the ________. A. transmitter B. channel C. information source D. destination

Description : Noise always affects the signal in a communications systems at the ________. A. transmitter B. channel C. information source D. destination

Last Answer : B. channel

What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB

Description : What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB

Last Answer : C. 40 dB

What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Description : What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Last Answer : C. Poor front-end selectivity

What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Description : What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Last Answer : B. 50 dB

What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Description : What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Last Answer : B. 3853 Hz

When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Description : When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Last Answer : D. internal receiver noise.

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Last Answer : C. In the receiver front end

The signal to noise ratio that is required for a satisfactory television reception. A. 30 dB B. 40 dB C. 10 dB D. 20 dB

Description : The signal to noise ratio that is required for a satisfactory television reception. A. 30 dB B. 40 dB C. 10 dB D. 20 dB

Last Answer : B. 40 dB

What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Last Answer : A. Interference to adjacent channel

What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB

Description : What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB

Last Answer : A. 50 dB

The random and unpredictable electric signal from natural causes, both internal and external to the system is know as ________. A. Distortion B. Noise C. Attenuation D. Interference

Description : The random and unpredictable electric signal from natural causes, both internal and external to the system is know as ________. A. Distortion B. Noise C. Attenuation D. Interference

Last Answer : B. Noise

Quantization noise is caused by A. binary coding techniques B. serial transmission errors C. the synchronization between encoder and decoder D. the approximation of the quantized signal

Description : Quantization noise is caused by A. binary coding techniques B. serial transmission errors C. the synchronization between encoder and decoder D. the approximation of the quantized signal

Last Answer : D. the approximation of the quantized signal

The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Description : The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Last Answer : D. 14 dB

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

How do the Pros determine which trends will fade and which ones will rise?

Description : How do the Pros determine which trends will fade and which ones will rise?

Last Answer : The pros don't predict the trends, they create the trends. They choose what to do based on past popular trends and the cultural climate at the time, as well as paying attention to the ... those trends. Consumer reports, surveys, and sales records are good indicators of where things are going too.

nif stands for A. Non-intrinsic figure B. Noise improvement factor C. Narrow intermediate frequency D. Noise interference figure

Description : nif stands for A. Non-intrinsic figure B. Noise improvement factor C. Narrow intermediate frequency D. Noise interference figure

Last Answer : B. Noise improvement factor

What is the noise factor if the equivalent noise temperature is 25 K? A. 1.09 B. 0.09 C. 0.36 dBm D. 0.36

Description : What is the noise factor if the equivalent noise temperature is 25 K? A. 1.09 B. 0.09 C. 0.36 dBm D. 0.36

Last Answer : A. 1.09

A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor

Description : A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor

Last Answer : A. Noise equivalent power

Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure

Description : Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure

Last Answer : C. Noise improvement factor

A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Last Answer : D. 8.8 dB

if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Description : if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Last Answer : Answers is the place to go to get the answers you need and to ask the questions you want

What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Description : What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Last Answer : A. Velocity factor

What is Noise Margin ?

Description : What is Noise Margin ?

Last Answer : The maximum amount of noise at the input of a logic gate that logic gate can properly output is called noise margin.

When does the noise margin allow digital circuits to function properly?

Description : When does the noise margin allow digital circuits to function properly?

Last Answer : When noise voltages are within the limits of VNA (High State Noise Margin) and VNK for a particular logic family.

Define noise margin?

Description : Define noise margin?

Last Answer : It is the maximum noise voltage added to an input signal of a digital circuit that does not cause an undesirable change in the circuit output. It is expressed in volts.

Define following terms related to logic families : (i) Noise Margin (ii) FAN-OUT (iii) Propagation delay (iv) Power dissipation

Description : Define following terms related to logic families : (i) Noise Margin (ii) FAN-OUT (iii) Propagation delay (iv) Power dissipation

Last Answer : i) Noise immunity is measured in terms of noise margin. High state Noise margin = VNH = VOH(min) - VIH(min) Low state Noise margin = VNL = VIL(max) - VOL(max) i) The fan-out is defined as the ... logical 0 state (HIGH to LOW) iii) Average power dissipation is defined as PD(avg) = ICC(avg) * VCC