Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level
Last Answer : D. Residual noise level
Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.
Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.
Description : Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference
Last Answer : C. Out of the band
Description : This is referred to a product of simultaneous frequency and amplitude modulation or a carrier frequency variation which produces unwanted distortion. A. Absorption modulation B. Simultaneous modulation C. Dynamic instability D. Series modulation
Last Answer : C. Dynamic instability
Description : If the carrier of a 100 percent modulation modulated AM wave is suppressed, the percentage power saving will be (A) 50.55 (B) 15.55 (C) 10.66 (D) 66.66
Last Answer : If the carrier of a 100 percent modulation modulated AM wave is suppressed, the percentage power saving will be 66.66
Description : The _______ technique uses M different carrier frequencies that are modulated by the source signal. At one moment, the sign modulates one carrier frequency; at the next moment, thesignal modulates another carrier frequency. A) FDM B) DSSS C) FHSS D) TDM
Last Answer : FHSS
Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power
Last Answer : A. Carrier power
Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power
Last Answer : C. Carrier power
Description : Noise from random acoustic or electric noise that has equal per cycle over a specified total frequency band. A. Thermal noise B. White noise C. Gaussian noise D. All of these
Last Answer : D. All of these
Description : Refers to the first symbol in an emission designation with an amplitude modulated main carrier represented by letter H. A. Single sideband suppressed carrier B. Double sideband full carrier C. Independent sideband D. Double sideband
Last Answer : B. Double sideband full carrier
Description : Which of the following antennas is used for testing and adjusting a transmitter for proper modulation, amplifier operation and frequency accuracy? A. Elementary B. Real C. Isotropic D. Dummy
Last Answer : D. Dummy
Description : Why are frequency modulation transmitters more efficient? A. Because their power is increased by class C amplifiers B. Because their power is increased by class A amplifiers C. Because their power is increased by class B amplifiers D. Because their power is increased by class AB amplifiers
Last Answer : A. Because their power is increased by class C amplifiers
Description : What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66
Last Answer : D. 1.66
Description : What is the term used to describe a spread spectrum communications system where the center frequency if a conventional carrier is altered many time per second in accordance with a pseudo ... hopping B. Direct sequence C. Time-domain frequency modulation D. Frequency compandored spread spectrum
Last Answer : A. Frequency hopping
Description : In modulation technique, which of the following is referred to audible pitch? A. Width B. Frequency C. Harmonic D. Amplitude
Last Answer : B. Frequency
Description : What is meant by the term deviation ratio? A. The ratio of the carrier center frequency to the audio modulating frequency B. The ratio of the highest audio modulating frequency to the ... audio modulation frequency D. The ratio of the audio modulating frequency to the center carrier frequency
Last Answer : C. The ratio of the maximum carrier frequency deviation to the highest audio modulation frequency
Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power
Last Answer : C. Mean power
Description : Which of the following systems is not used in radio detection and ranging? A. Frequency shift B. Frequency modulation C. Pulse radar D. Amplitude modulation
Last Answer : D. Amplitude modulation
Description : The modulation technique used by GSM cellular system A. Phase shift keying B. Frequency shift keying C. Gaussian minimum shift keying D. QAM
Last Answer : C. Gaussian minimum shift keying
Description : Used for time division multiplexing. A. Frequency modulation B. Pulsed modulation C. SSB D. Amplitude modulation
Last Answer : B. Pulsed modulation
Description : A good example of a pilot tone system used in commercial frequency modulation stations. A. FDM B. Time division C. Stereo multiplexing D. Frequency modulation
Last Answer : C. Stereo multiplexing
Description : Both frequency and phase modulation utilize ________ modulation A. Phase B. AM and FM C. Digital D. Angle
Last Answer : D. Angle
Description : Which determines the number of sideband components of FM? A. Modulation frequency B. Modulation index C. Carrier frequency D. All of these
Last Answer : B. Modulation index
Description : What is the difference between phase and frequency modulation? A. Is purely theoretical because they are the same in practice B. Lies in poorer audio response of phase modulation C. Lies in the different definitions of the modulation index D. Is too great to make two systems compatible
Last Answer : C. Lies in the different definitions of the modulation index
Description : What is the main purpose of a communications system? A. None of these B. To have a frequency assignment C. For modulation D. To provide an acceptable replica of the information at the destination
Last Answer : D. To provide an acceptable replica of the information at the destination
Description : ECE Board Exam March 1996 The modulation system used for telegraphy is A. frequency-shift keying B. two-tone modulation C. pulse-code modulation D. single-tone modulation
Last Answer : A. frequency-shift keying
Last Answer : Frequency modulation gives Less noise
Description : What is the proper procedure for suppressing electrical noise in a mobile station? A. Apply shielding and filtering where necessary B. Insulate a all plain sheet metal surfaces from each other C. ... -static spray liberally to all nonmetallic D. Install filter capacitors in series with all dc wiring
Last Answer : A. Apply shielding and filtering where necessary
Description : Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise
Last Answer : D. Miscellaneous noise
Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV
Last Answer : B. 4.0 µV
Description : Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.
Last Answer : B. Impulse noise voltage is dependent on bandwidth
Description : Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high
Last Answer : D. high
Description : Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz
Last Answer : C. 15 to 160 MHz
Description : nif stands for A. Non-intrinsic figure B. Noise improvement factor C. Narrow intermediate frequency D. Noise interference figure
Last Answer : B. Noise improvement factor
Description : What is the reference frequency of CCIT phosphomeric noise measurement? A. 800 Hz B. 1000 Hz C. 1500 Hz D. 3400 Hz
Last Answer : A. 800 Hz
Description : Unwanted radio signal on assigned frequency. A. Splatter B. RFI C. Noise D. EMI
Last Answer : C. Noise
Description : Noise from random acoustic or electric noise that has equal energy per cycle over a specified total frequency band. A. Gaussian noise B. Whiter noise C. Thermal noise D. All of the above
Last Answer : D. All of the above
Description : Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure
Last Answer : C. Noise improvement factor
Description : What is the reference frequency of CCITT psophometric noise measurement? A. 800 Hz B. 1500 Hz C. 3400 Hz D. 1000 Hz
Description : Industrial noise frequency is between _________. A. 200 to 3000 Mhz B. 15 to 160 Mhz C. 0 to 10 Khz D. 20 Ghz
Last Answer : B. 15 to 160 Mhz
Description : One of the reasons why FDM is being replaced by TDM is A. noise is amplified with voice when an FDM system is used B. it is difficult to place channels side by side C. there is more time than frequency D. Most available frequencies has been used
Last Answer : A. noise is amplified with voice when an FDM system is used
Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone
Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz
Description : Select the antihistaminic which modulates calcium channels and has prominant labyrinthine suppressant property: A. Cyproheptadine B. Cinnarizine C. Clemastine D. Cetirizine
Last Answer : B. Cinnarizine
Description : Modulation in which no signal is present between pulses A. Pulse modulation B. QAM C. PSK D. FSK
Last Answer : A. Pulse modulation
Description : Which noise is produced by lighting discharges in thunderstorms? A. White noise B. Extraterrestrial noise C. Industrial noise D. Atmospheric noise
Last Answer : D. Atmospheric noise
Description : _________ is measured on a circuit when it is correctly terminated but does not have any traffic. A. White noise B. Galactic noise C. Impulse noise D. Atmospheric noise
Last Answer : A. White noise
Description : The most common unit of noise measurement in white noise voltage testing. A. NPR B. dBm C. dBW D. dBrn
Last Answer : A. NPR
Description : Noise caused by the thermal agitation of electrons in resistance. A. All of these B. Thermal noise C. Johnson’s noise D. White noise
Last Answer : A. All of these
Description : The most common unit of noise measurement in white noise testing. A. dBw B. dBk C. dBm D. NPR
Last Answer : D. NPR
Description : When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases
Last Answer : D. Antenna resonant frequency increases