What is "pu" in electrical engineering?

What is "pu" in electrical engineering?
by

2 Answers

Answer :

A:Pu stands for per unit. This is used in single line diagram of power distribution. Power        distribution is like a huge electrical circuit with number of components (generators,    transformers, loads) with different ratings (in MVA and KV). To bring all the ratings into    common platform we use pu concept in which, in general largest MVA and KV ratings of the   component is considered as base values.
by

Answer :

PU stands for per unit and this will be used in power system single line diagram there it is like a huge electrical circuit with no of components (generators, transformers, loads) with different ratings (in MVA and KV). To bring all the ratings into common platform we use pu concept in which, in general largest MVA and KV ratings of the component is considered as base values, then all other component ratings will get back into this basis. Those values are called as pu values. (p.u=actual value/base value).
by

Related questions

What are the various types of tariff?

Description : What are the various types of tariff?

Last Answer : 1. Simple tariff 2. Flat rate tariff 3. Block rate tariff 4. Two-part tariff 5. Maximum demand tariff 6. Power factor tariff 7. Three-part tariff

What is tariff?

Description : What is tariff?

Last Answer : The rate at which electrical energy is supplied to a consumer is known as tariff. The tariff should include the following items: (i) Recovery of cost of producing electrical energy at the power ... of cost of operation and maintenance of supply (iv) A suitable profit on the capital investment.

How can we reduce the effect of corona?

Description : How can we reduce the effect of corona?

Last Answer : 1. By increasing conductor size: By increasing conductor size, the voltage at which corona occurs is raised and hence corona effects are considerably reduced. 2. By increasing conductor spacing: ... , the voltage at which corona occurs is raised and hence corona effects can be eliminated.

What is corona?

Description : What is corona?

Last Answer : The phenomenon of violet glow, hissing noise and production of ozone gas in an overhead transmission line is known as corona.

What is meant by Sag?

Description : What is meant by Sag?

Last Answer : The difference in level between points of supports and the lowest point on the conductor is called sag.

What is difference between fuse and breaker?

Description : What is difference between fuse and breaker?

Last Answer : A: (i) Fuse performs both detection and interruption functions. Circuit breaker performs interruption function only. The detection of fault is made by relay system. (ii) The breaking capacity of ... , replacement is required in the fuse. In case of circuit breaker, replacement is not required.

Which type of motor is used in trains, what is the rating of supply used?

Description : Which type of motor is used in trains, what is the rating of supply used?

Last Answer : A:Dc series is in the trains to get high starting torque while starting of the trains and operating voltage is 1500v dc.

Why we use ac system in India why not dc ?

Description : Why we use ac system in India why not dc ?

Last Answer : A:Firstly, the output of power stations comes from a rotary turbine, which by it's nature is AC and therefore requires no power electronics to convert to DC. Secondly it is much easier to ... the sine wave current will naturally tend to zero at some point making the current easier to interrupt.

Why electricity in India is in the multiples of 11 like 11kv, 22kv, 33kv ?

Description : Why electricity in India is in the multiples of 11 like 11kv, 22kv, 33kv ?

Last Answer : A:Transformer Induced voltage equation contains 4.44 factor. E -Induced emf per phase T -number of turns f -frequency Φ -maximum flux per pole From the equation we see that E is proportional to 4.4 and it is in turn multiple of 11.So always transmission voltage is multiple of 11

When we connect the large capacitor bank in series ?

Description : When we connect the large capacitor bank in series ?

Last Answer : A :we connect large capacitor bank in series to improve the voltage power supply at the load end in balanced transmission line when there is considerable voltage drop along the balanced transmission line due ... - %6 )of the rated high terminal voltage )the large capacitor bank is used in series.

What is reverse power relay?

Description : What is reverse power relay?

Last Answer : A:Reverse Power flow relay are used in generating stations's protection. A generating stations is supposed to fed power to the grid and in case generating units are off,there is no generation in the ... power from grid. To stop the flow of power from grid to generator we use reverse power relay.

What is the difference between over voltage relay and over current relay?

Description : What is the difference between over voltage relay and over current relay?

Last Answer : A:The current increases not only for over voltages but also for under voltage(As most of the loads are non-linear in nature). So,the over voltage protection & over current protection are completely ... , for a better protection of the system.It should have both over voltage & over current relay.

What is derating?

Description : What is derating?

Last Answer : A:The current currying of cables will change depending upon the site temperature (location of site), type of run (it will run through duct, trench, buried etc.), number of tray, depth ... of cable reduce than current currying capacity (which given to cable Catalogue) this is called derating.

Define IDMT relay?

Description : Define IDMT relay?

Last Answer : It is an Inverse Definite Minimum Time relay. In IDMT relay its operating is inversely proportional and also a characteristic of minimum time after which this relay operates. It is inverse in the sense; the tripping time will decrease as the magnitude of fault current increase.

Where should the lighting arrestor be placed in distribution lines?

Description : Where should the lighting arrestor be placed in distribution lines?

Last Answer : A:Near distribution transformers and out going feeders of 11kv and incomming feeder of 33kv and near power transformers in sub-stations.

What is the difference between MCB & MCCB, Where it can be used?

Description : What is the difference between MCB & MCCB, Where it can be used?

Last Answer : A: MCB is miniature circuit breaker which is thermal operated for overload condition and magnetically operated for short circuit protection. It is available in small current rating. MCCB is moulded case ... frequency may be inbuilt. Normally it is used where normal current is more than 100 A.

Explain types of Earthing.

Description : Explain types of Earthing.

Last Answer : A:The two types of earthing are Equipment earthing and system earthing. In Equipment earthing: body ( non conducting part) of the equipment should be earthed to safegaurd the human beings ... . This type of earthing is further classified into directly earthed, Impedance earthing, resistive earthing.

What is Ferranti effect?

Description : What is Ferranti effect?

Last Answer : A: When receiving end voltage is greater than the sending end voltage.

What is buchholz relay and the significance of it in to the transformer?

Description : What is buchholz relay and the significance of it in to the transformer?

Last Answer : A:Buchholz relay is a gas based relay which is used for the protection of transformer from its internal faults. whenever any internal fault occurs in a transformer, the buchholz relay at once gives an ... then it stop its sound itself other wise it trips the circuit by its own tripping mechanism.

What is the difference between Isolator and Circuit Breaker?

Description : What is the difference between Isolator and Circuit Breaker?

Last Answer : A: Isolator is a off load device which is used for isolating the downstream circuits from upstream circuits for the reason of any maintenance on downstream circuits. it is manually operated ... specification 1) rated current 2) short circuit breaking capacity and 3) Instantaneous tripping current.

what is power factor? whether it should be high or low? why?

Description : what is power factor? whether it should be high or low? why?

Last Answer : A:Power factor is the ratio of true power to apparent power. It has to be ideally 1. If it is too low then cable over heating & equipment overloading will occur. if it is greater than 1 then load will ... : 0.95 to meet actual power, load has to draw less current(V constant),result in less losses).

Explain the working principle of the circuit breaker

Description : Explain the working principle of the circuit breaker

Last Answer : A:Circuit Breaker is one which makes or breaks the circuit.It has two contacts namely fixed contact & moving contact. Under normal condition the moving contact comes in contact with fixed contact thereby forming ... . Arc is extinguished by the Arc Quenching media like air, oil, vacuum, SF6 gas etc.

What is the difference between surge arrestor and lightning arrestor?

Description : What is the difference between surge arrestor and lightning arrestor?

Last Answer : A:Lightning Arrestor is installed outside and the effect of lightning is grounded where as surge arrestor installed inside panels comprising of resistors which consumes the energy and nullify the effect of surge.

Why we use Vacuum Circuit Breaker in High Transmission System and not Air Circuit Breaker?

Description : Why we use Vacuum Circuit Breaker in High Transmission System and not Air Circuit Breaker?

Last Answer : A:Vacuum has high arc quenching property compare to air . The dielectric strength of vacuum is equal to 8 times than air . Hence vacuum circuit breaker is used in High voltage line and air circuit breaker is used in low voltage lines.

Why syn. generators are used for the production of electricity?

Description : Why syn. generators are used for the production of electricity?

Last Answer : A:synchronous machines have capability to work on different power factor. Hence syn. generators are used for the production of electricity.

What will happen when power factor is leading in distribution of power?

Description : What will happen when power factor is leading in distribution of power?

Last Answer : A:If their is high power factor, i.e if the power factor is close to one: 1.losses in form of heat will be reduced, 2.cable becomes less bulky and easy to carry, and very cheap to afford, & 3. it also reduces over heating of transformers.

what is ACSR cable and where we use it?

Description : what is ACSR cable and where we use it?

Last Answer : A: ACSR means Aluminium conductor steel reinforced, this conductor is used in transmission & distribution.

Describe the operation carried out in Thermal power stations?

Description : Describe the operation carried out in Thermal power stations?

Last Answer : A:The water is boiled in the boiler with the help of coal. This generates steam. This steam is allowed to hit the turbine hence the turbine rotates. The turbine is coupled with generator. So the mechanical energy of turbine is converted to electrical energy by Generator.

What is Electric traction?

Description : What is Electric traction?

Last Answer : A:Electric traction means using the electric power for traction system to drive the locomotives.

What is meant by synchronous condenser?

Description : What is meant by synchronous condenser?

Last Answer : An over excited synchronous motor running on no load is known as synchronous condenser. It is used to improve the power factor of the system.

What is “pu” in electrical engineering?

Description : What is “pu” in electrical engineering?

Last Answer :  Pu stands for per unit and this will be used in power system single line diagram there it is like a huge electrical circuit with no of components (generators, transformers, loads) with different ratings ( ... into this basis. Those values are called as pu values. (p.u=actual value/base value).

What is phase angle in electrical engineering ?

Description : What is phase angle in electrical engineering ?

Last Answer : In electrical engineering, phase angle is the angular difference in phase between two sinusoidal waves or signals. It is typically measured in degrees or radians, and it represents the amount of shift or ... and current in an AC circuit can affect the power factor and the efficiency of the circuit.

A ground in an electrical circuit outside the engine room _____________. A. cannot be detected under normal conditions B. is of no consequence to engineering personnel C. is indicated at the branch circuit breaker panel D. is indicated by the ground detecting lamps on the main switchboard

Description : A ground in an electrical circuit outside the engine room _____________. A. cannot be detected under normal conditions B. is of no consequence to engineering personnel C. is indicated at the branch circuit breaker panel D. is indicated by the ground detecting lamps on the main switchboard

Last Answer : Answer: D

What Is The One Main Difference Between Ups & Inverter ? And Electrical Engineering & Electronics Engineering ?

Description : What Is The One Main Difference Between Ups & Inverter ? And Electrical Engineering & Electronics Engineering ?

Last Answer : uninterrupted power supply is mainly use for short time .me according to ups VA it gives backup. ups is also two types : on line. offline. online ups having high volt and amp for long time backup ... but inverter is start with 2v,24,dc to 36v dc and 20amp to 80amp battery with long time backup.

WIRING in electrical engineering

Description : WIRING in electrical engineering

Last Answer : WIRING METHODS A circuit is a path along which the electric current flows from the negative Side of the power source to the positive side. There are three types of electrical circuit. (i) Series ... down, the other devices continue to operate. Hence this type of circuit is used in home wiring.

ELECTRICAL ENGINEERING PRACTICE - SAFETY MEASURES

Description : ELECTRICAL ENGINEERING PRACTICE - SAFETY MEASURES

Last Answer : 1. Use approved tools, equipment's and protective devices. 2. Do not work under poor light or when you are tired. 3. Do not work in damp areas or in wet shoes or clothes. 4. Keep ... appliances away from heated surfaces and open flames. 11. Check the electric power supply from the switch position.

How can you relate power engineering with electrical engineering?

Description : How can you relate power engineering with electrical engineering?

Last Answer : Power engineering is a sub division of electrical engineering. It deals with generation, transmission and distribution of energy in electrical form. Design of all power equipments also comes under power ... systems and they might work on off grid systems that are not connected to the system.

What would be on your pu-pu platter?

Description : What would be on your pu-pu platter?

Last Answer : I’d like to have some sort of fried tofu, with a wonderful sweet and sour dipping sauce. And some stuffed squash blossoms, and some marinated mushrooms. What would you guys like to have on your own, personal, pu-pu platter?

Can anyone tell me more about the PU surgery my cat had last night?

Description : Can anyone tell me more about the PU surgery my cat had last night?

Last Answer : answer:He absolutely must wear his e-collar! If he won't eat with it on, you can take it off while you are supervising him, but if left unattended, he will chew out his sutures ... thorough discharge instructions form your vet and make sure to ask questions about anything that you don't understand.

What does PU stand for?

Description : What does PU stand for?

Last Answer : Pennsylvania University

What does "PU" stand for in that "PU" that stinks?

Description : What does "PU" stand for in that "PU" that stinks?

Last Answer : it’s not “p” “u”.....it’s pew.

What is the atomic number of Pu ?

Description : What is the atomic number of Pu ?

Last Answer : The atomic number of Pu is 94

Which among the following `"is"//"are"` fissible? a)`._(92)U^(235)` b)`._(92)U^(238)` c)`._(94)Pu^(239)` d)`._(94)Pu^(238)`

Description : Which among the following `"is"//"are"` fissible? a)`._(92)U^(235)` b)`._(92)U^(238)` c)`._(94)Pu^(239)` d)`._(94)Pu^(238)`

Last Answer : Which among the following `"is"//"are"` fissible? a)`._(92)U^(235)` b)`._(92)U^(238)` c)`._(94)Pu^(239)` ... ` C. `._(94)^(239)Pu` D. `._(94)^(238)Pu`

Out of the following, nucleus of __________ atom contains the largest number of neutrons. (A) U-235 (B) U-238 (C) U-239 (D) Pu-239

Description : Out of the following, nucleus of __________ atom contains the largest number of neutrons. (A) U-235 (B) U-238 (C) U-239 (D) Pu-239

Last Answer : (C) U-239

A fast breeder reactor (A) Utilises fast neutrons for causing fission (B) Converts fertile material (e.g., U-238) into fissile material (Pu-239) (C) Normally employs molten sodium as coolant (D) All (A), (B) and (C)

Description : A fast breeder reactor (A) Utilises fast neutrons for causing fission (B) Converts fertile material (e.g., U-238) into fissile material (Pu-239) (C) Normally employs molten sodium as coolant (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which is not a fissile nuclear material? (A) U-233 (B) U-235 (C) U-238 (D) Pu-239

Description : Which is not a fissile nuclear material? (A) U-233 (B) U-235 (C) U-238 (D) Pu-239

Last Answer : (C) U-238

Enrichment of uranium is done to increase the concentration of__________ in the natural uranium.(A) U-238(B) U-233(C) U-235(D) Pu-239

Description : Enrichment of uranium is done to increase the concentration of__________ in the natural uranium. (A) U-238 (B) U-233 (C) U-235 (D) Pu-239

Last Answer : (C) U-235

The compound of potassium used for pu- rifying water?

Description : The compound of potassium used for pu- rifying water?

Last Answer : Potassium Permanganate

Which is a fertile nuclear fuel? (A) U-233(B) U-235 (C) Pu-239 (D) Th-232

Description : Which is a fertile nuclear fuel? (A) U-233 (B) U-235 (C) Pu-239 (D) Th-232

Last Answer : (D) Th-232

Which of the following is the best nuclear fuel? (A) Np - 239 (B) U-234 (C) Pu -239 (D) Th-236

Description : Which of the following is the best nuclear fuel? (A) Np - 239 (B) U-234 (C) Pu -239 (D) Th-236

Last Answer : (C) Pu -239