Describe the operation carried out in Thermal power stations?

Describe the operation carried out in Thermal power stations?
by

1 Answer

Answer :

A:The water is boiled in the boiler with the help of coal. This generates steam. This steam is       allowed to hit the turbine hence the turbine rotates. The turbine is coupled with generator.     So the mechanical energy of turbine is converted to electrical energy by Generator.
by

Related questions

Operation Carried Out In Thermal Power Stations?

Description : Operation Carried Out In Thermal Power Stations?

Last Answer : The water is obtained in the boiler and the coal is burnt so that steam is obtained this steam is allowed to hit the turbine , the turbine which is coupled with the generator generates the electricity.

What is reverse power relay?

Description : What is reverse power relay?

Last Answer : A:Reverse Power flow relay are used in generating stations's protection. A generating stations is supposed to fed power to the grid and in case generating units are off,there is no generation in the ... power from grid. To stop the flow of power from grid to generator we use reverse power relay.

what is power factor? whether it should be high or low? why?

Description : what is power factor? whether it should be high or low? why?

Last Answer : A:Power factor is the ratio of true power to apparent power. It has to be ideally 1. If it is too low then cable over heating & equipment overloading will occur. if it is greater than 1 then load will ... : 0.95 to meet actual power, load has to draw less current(V constant),result in less losses).

What will happen when power factor is leading in distribution of power?

Description : What will happen when power factor is leading in distribution of power?

Last Answer : A:If their is high power factor, i.e if the power factor is close to one: 1.losses in form of heat will be reduced, 2.cable becomes less bulky and easy to carry, and very cheap to afford, & 3. it also reduces over heating of transformers.

What are the various types of tariff?

Description : What are the various types of tariff?

Last Answer : 1. Simple tariff 2. Flat rate tariff 3. Block rate tariff 4. Two-part tariff 5. Maximum demand tariff 6. Power factor tariff 7. Three-part tariff

What is tariff?

Description : What is tariff?

Last Answer : The rate at which electrical energy is supplied to a consumer is known as tariff. The tariff should include the following items: (i) Recovery of cost of producing electrical energy at the power ... of cost of operation and maintenance of supply (iv) A suitable profit on the capital investment.

How can we reduce the effect of corona?

Description : How can we reduce the effect of corona?

Last Answer : 1. By increasing conductor size: By increasing conductor size, the voltage at which corona occurs is raised and hence corona effects are considerably reduced. 2. By increasing conductor spacing: ... , the voltage at which corona occurs is raised and hence corona effects can be eliminated.

What is corona?

Description : What is corona?

Last Answer : The phenomenon of violet glow, hissing noise and production of ozone gas in an overhead transmission line is known as corona.

What is meant by Sag?

Description : What is meant by Sag?

Last Answer : The difference in level between points of supports and the lowest point on the conductor is called sag.

What is difference between fuse and breaker?

Description : What is difference between fuse and breaker?

Last Answer : A: (i) Fuse performs both detection and interruption functions. Circuit breaker performs interruption function only. The detection of fault is made by relay system. (ii) The breaking capacity of ... , replacement is required in the fuse. In case of circuit breaker, replacement is not required.

Which type of motor is used in trains, what is the rating of supply used?

Description : Which type of motor is used in trains, what is the rating of supply used?

Last Answer : A:Dc series is in the trains to get high starting torque while starting of the trains and operating voltage is 1500v dc.

Why we use ac system in India why not dc ?

Description : Why we use ac system in India why not dc ?

Last Answer : A:Firstly, the output of power stations comes from a rotary turbine, which by it's nature is AC and therefore requires no power electronics to convert to DC. Secondly it is much easier to ... the sine wave current will naturally tend to zero at some point making the current easier to interrupt.

Why electricity in India is in the multiples of 11 like 11kv, 22kv, 33kv ?

Description : Why electricity in India is in the multiples of 11 like 11kv, 22kv, 33kv ?

Last Answer : A:Transformer Induced voltage equation contains 4.44 factor. E -Induced emf per phase T -number of turns f -frequency Φ -maximum flux per pole From the equation we see that E is proportional to 4.4 and it is in turn multiple of 11.So always transmission voltage is multiple of 11

When we connect the large capacitor bank in series ?

Description : When we connect the large capacitor bank in series ?

Last Answer : A :we connect large capacitor bank in series to improve the voltage power supply at the load end in balanced transmission line when there is considerable voltage drop along the balanced transmission line due ... - %6 )of the rated high terminal voltage )the large capacitor bank is used in series.

What is the difference between over voltage relay and over current relay?

Description : What is the difference between over voltage relay and over current relay?

Last Answer : A:The current increases not only for over voltages but also for under voltage(As most of the loads are non-linear in nature). So,the over voltage protection & over current protection are completely ... , for a better protection of the system.It should have both over voltage & over current relay.

What is derating?

Description : What is derating?

Last Answer : A:The current currying of cables will change depending upon the site temperature (location of site), type of run (it will run through duct, trench, buried etc.), number of tray, depth ... of cable reduce than current currying capacity (which given to cable Catalogue) this is called derating.

Define IDMT relay?

Description : Define IDMT relay?

Last Answer : It is an Inverse Definite Minimum Time relay. In IDMT relay its operating is inversely proportional and also a characteristic of minimum time after which this relay operates. It is inverse in the sense; the tripping time will decrease as the magnitude of fault current increase.

Where should the lighting arrestor be placed in distribution lines?

Description : Where should the lighting arrestor be placed in distribution lines?

Last Answer : A:Near distribution transformers and out going feeders of 11kv and incomming feeder of 33kv and near power transformers in sub-stations.

What is the difference between MCB & MCCB, Where it can be used?

Description : What is the difference between MCB & MCCB, Where it can be used?

Last Answer : A: MCB is miniature circuit breaker which is thermal operated for overload condition and magnetically operated for short circuit protection. It is available in small current rating. MCCB is moulded case ... frequency may be inbuilt. Normally it is used where normal current is more than 100 A.

Explain types of Earthing.

Description : Explain types of Earthing.

Last Answer : A:The two types of earthing are Equipment earthing and system earthing. In Equipment earthing: body ( non conducting part) of the equipment should be earthed to safegaurd the human beings ... . This type of earthing is further classified into directly earthed, Impedance earthing, resistive earthing.

What is Ferranti effect?

Description : What is Ferranti effect?

Last Answer : A: When receiving end voltage is greater than the sending end voltage.

What is buchholz relay and the significance of it in to the transformer?

Description : What is buchholz relay and the significance of it in to the transformer?

Last Answer : A:Buchholz relay is a gas based relay which is used for the protection of transformer from its internal faults. whenever any internal fault occurs in a transformer, the buchholz relay at once gives an ... then it stop its sound itself other wise it trips the circuit by its own tripping mechanism.

What is the difference between Isolator and Circuit Breaker?

Description : What is the difference between Isolator and Circuit Breaker?

Last Answer : A: Isolator is a off load device which is used for isolating the downstream circuits from upstream circuits for the reason of any maintenance on downstream circuits. it is manually operated ... specification 1) rated current 2) short circuit breaking capacity and 3) Instantaneous tripping current.

Explain the working principle of the circuit breaker

Description : Explain the working principle of the circuit breaker

Last Answer : A:Circuit Breaker is one which makes or breaks the circuit.It has two contacts namely fixed contact & moving contact. Under normal condition the moving contact comes in contact with fixed contact thereby forming ... . Arc is extinguished by the Arc Quenching media like air, oil, vacuum, SF6 gas etc.

What is the difference between surge arrestor and lightning arrestor?

Description : What is the difference between surge arrestor and lightning arrestor?

Last Answer : A:Lightning Arrestor is installed outside and the effect of lightning is grounded where as surge arrestor installed inside panels comprising of resistors which consumes the energy and nullify the effect of surge.

Why we use Vacuum Circuit Breaker in High Transmission System and not Air Circuit Breaker?

Description : Why we use Vacuum Circuit Breaker in High Transmission System and not Air Circuit Breaker?

Last Answer : A:Vacuum has high arc quenching property compare to air . The dielectric strength of vacuum is equal to 8 times than air . Hence vacuum circuit breaker is used in High voltage line and air circuit breaker is used in low voltage lines.

Why syn. generators are used for the production of electricity?

Description : Why syn. generators are used for the production of electricity?

Last Answer : A:synchronous machines have capability to work on different power factor. Hence syn. generators are used for the production of electricity.

what is ACSR cable and where we use it?

Description : what is ACSR cable and where we use it?

Last Answer : A: ACSR means Aluminium conductor steel reinforced, this conductor is used in transmission & distribution.

What is "pu" in electrical engineering?

Description : What is "pu" in electrical engineering?

Last Answer : PU stands for per unit and this will be used in power system single line diagram there it is like a huge electrical circuit with no of components (generators, transformers, loads) with different ratings (in ... into this basis. Those values are called as pu values. (p.u=actual value/base value).

What is Electric traction?

Description : What is Electric traction?

Last Answer : A:Electric traction means using the electric power for traction system to drive the locomotives.

What is meant by synchronous condenser?

Description : What is meant by synchronous condenser?

Last Answer : An over excited synchronous motor running on no load is known as synchronous condenser. It is used to improve the power factor of the system.

Operation carried out in Thermal power station?

Description : Operation carried out in Thermal power station?

Last Answer : The water is obtained in the boiler and the coal is burnt so that steam is obtained this steam is allowed to hit the turbine; the turbine which is coupled with the generator generates the electricity

What are the operation carried out in Thermal power station?

Description : What are the operation carried out in Thermal power station?

Last Answer : A: The water is obtained in the boiler and the coal is burnt so that steam is obtained this steam is allowed to hit the turbine, the turbine which is coupled with the generator generates the electricity

Which of the following actions can be carried out in order to prevent thermal runaway in a transistor? A. Increase the current through the collector-base junction. B. Install a heat sink. C. Shift the 'Q' point to increase collector current. D. Increase the potential difference between the emitter and the base.

Description : Which of the following actions can be carried out in order to prevent thermal runaway in a transistor? A. Increase the current through the collector-base junction. B. Install a heat sink. ... point to increase collector current. D. Increase the potential difference between the emitter and the base.

Last Answer : Answer: B

In replacing a defective transformer with a new one, which of the following actions must be carried out to insure proper operation of the equipment it serves? A. The secondary leads must be grounded for 10 minutes to remove static charges. B. The transformer connections must be made as before with regard to the indicated polarity. C. The iron core of the transformer must be flashed to pre-magnetize it. D. The iron core must be grounded for 10 minutes to remove any residual magnetism.

Description : In replacing a defective transformer with a new one, which of the following actions must be carried out to insure proper operation of the equipment it serves? A. The secondary leads must be grounded ... magnetize it. D. The iron core must be grounded for 10 minutes to remove any residual magnetism.

Last Answer : Answer: B

In large thermal power stations very fine particulates present in flue gas are removed by (A) Wet scrubber (B) Bag filter (C) Electrostatic precipitators (D) Dust catcher

Description : In large thermal power stations very fine particulates present in flue gas are removed by (A) Wet scrubber (B) Bag filter (C) Electrostatic precipitators (D) Dust catcher

Last Answer : (C) Electrostatic precipitators

Common applications of Cooling towers include a. Cooling the circulating water used in oil refineries b. petrochemical and other chemical plants c. thermal power stations d. All of the above.

Description : Common applications of Cooling towers include a. Cooling the circulating water used in oil refineries b. petrochemical and other chemical plants c. thermal power stations d. All of the above.

Last Answer : All of the above.

Due to perturbation of the orbit, satellite orbit parameters are frequently updated on measurements carried out by its (A) Six ground stations (B) Five ground stations (C) Four ground stations (D) Three ground stations

Description : Due to perturbation of the orbit, satellite orbit parameters are frequently updated on measurements carried out by its (A) Six ground stations (B) Five ground stations (C) Four ground stations (D) Three ground stations

Last Answer : Answer: Option B

Power necessary to operate the horn relay shown in the illustration ____________. EL-0093 A. comes from each station's magneto B. is supplied from a 115 volt source C. is conducted through the relay's contacts D. also lights lamps 'R' and 'T'

Description : Power necessary to operate the horn relay shown in the illustration ____________. EL-0093 A. comes from each station's magneto B. is supplied from a 115 volt source C. is conducted through the relay's contacts D. also lights lamps 'R' and 'T'

Last Answer : Answer: A

Power necessary to operate the horn shown in the illustration _____________. EL-0093 A. comes from each station's magneto B. is supplied from a 115 volt source C. is conducted through a relay coil D. also lights lamps 'R' and 'T'

Description : Power necessary to operate the horn shown in the illustration _____________. EL-0093 A. comes from each station's magneto B. is supplied from a 115 volt source C. is conducted through a relay coil D. also lights lamps 'R' and 'T'

Last Answer : Answer: B

The electrical energy necessary to power a sound-powered telephone's small vibrating bell is obtained from _________. A. the emergency batteries for the general alarm B. each station's hand-cranked generator C. the emergency switchboard D. normal 115 volt DC supplies

Description : The electrical energy necessary to power a sound-powered telephone's small vibrating bell is obtained from _________. A. the emergency batteries for the general alarm B. each station's hand-cranked generator C. the emergency switchboard D. normal 115 volt DC supplies

Last Answer : Answer: B

What are the base load and peak load power stations?

Description : What are the base load and peak load power stations?  

Last Answer : During certain periods the load demands are very high. Example the morning when all factories operate. During these time certain power plants like thermal plants gives this extra power required. ... easily stopped or restated. Nuclear power station comes under Base load power station category.  

Which of the following regulates the ownership and operation of radio and television stations in the country? A. PD 576-A B. PD 756 C. PD 657 D. PD 677

Description : Which of the following regulates the ownership and operation of radio and television stations in the country? A. PD 576-A B. PD 756 C. PD 657 D. PD 677

Last Answer : A. PD 576-A

A law that specifically requires the service of a duly registered electronics and communications engineer in the designing installation and construction, operation and maintenance of radio stations. A. Act 3846 B. LOl 1000 C. R.A. 5734 D. Dept. order 88

Description : A law that specifically requires the service of a duly registered electronics and communications engineer in the designing installation and construction, operation and maintenance of radio stations. A. Act 3846 B. LOl 1000 C. R.A. 5734 D. Dept. order 88

Last Answer : D. Dept. order 88

Radio communication operation service between mobile and land stations or between mobile stations. A. Land mobile satellite service B. Maritime mobile service C. Mobile service D. Land mobile

Description : Radio communication operation service between mobile and land stations or between mobile stations. A. Land mobile satellite service B. Maritime mobile service C. Mobile service D. Land mobile

Last Answer : C. Mobile service

What are the tests to be carried out during DC high voltage test on power cables?

Description : What are the tests to be carried out during DC high voltage test on power cables? 

Last Answer : DC high voltage testing. During DC high voltage testing flow of following currents will take place. a. Capacitance charging current. b. Dielectric absorption current. c. Surface leakage current. d. Partial discharge current (corona). e. Volumetric leakage current. 

How is thermal insulation carried out in modern construction?

Description : How is thermal insulation carried out in modern construction?

Last Answer : The rise in the cost of utilities and heat energy makes today more and more often think about ways to protect buildings from heat loss. And this is no coincidence, because in this way you can ... , glue insulation, reinforce the surface. But the final finishing should still be done in warm weather.

In a power plant, coal is carried from storage place to boilers generally by means of (A) bucket (B) V-belts (C) trolleys (D) manually.

Description : In a power plant, coal is carried from storage place to boilers generally by means of (A) bucket (B) V-belts (C) trolleys (D) manually.

Last Answer : Ans: B

The size of a conductor used in power cables depends on the (A) operating voltage. (B) power factor. (C) current to be carried. (D) type of insulation used.

Description : The size of a conductor used in power cables depends on the (A) operating voltage. (B) power factor. (C) current to be carried. (D) type of insulation used.

Last Answer : (C) current to be carried.

Filtration operation carried out by continuous increase of the inlet pressure of slurry, is called the __________ filtration. (A) Constant rate (B) Varying pressure (C) Varying rate (D) Constant pressure

Description : Filtration operation carried out by continuous increase of the inlet pressure of slurry, is called the __________ filtration. (A) Constant rate (B) Varying pressure (C) Varying rate (D) Constant pressure

Last Answer : (A) Constant rate