Explain difference between modulus of resilience and modulus of rigidity ?

Explain difference between modulus of resilience and modulus of rigidity ?
by

1 Answer

Answer :

Modulus of resilience is the maximum strain energy stored in a material per unit volume and modulus of
rigidity is the ratio of shearing stress to the shearing strain within the elastic limit.
by

Related questions

In the relation ( T/J = Gθ/L = τ/ R), the letter G denotes modulus of ______ a. elasticity b. plasticity c. rigidity d. resilience

Description : In the relation ( T/J = Gθ/L = τ/ R), the letter G denotes modulus of ______ a. elasticity b. plasticity c. rigidity d. resilience

Last Answer : c. rigidity

What is the difference between proof resilience and modulus of resilience ?

Description : What is the difference between proof resilience and modulus of resilience ?

Last Answer : Proof resilience is the maximum strain energy that can be stored in a material without permanent deformation. Modulus of resilience is the maximum strain energy stored in a material per unit volume.

The shafts are designed on the basis of a. strength and rigidity. b. ductility. c. malleablility. d. resilience.

Description : The shafts are designed on the basis of a. strength and rigidity. b. ductility. c. malleablility. d. resilience.

Last Answer : a. strength and rigidity.

Modulus of resilience is defined as a) Strain energy per unit volume b) Strain energy per unit area c) Independent of strain energy d) None of the mentioned

Description : Modulus of resilience is defined as a) Strain energy per unit volume b) Strain energy per unit area c) Independent of strain energy d) None of the mentioned

Last Answer : a) Strain energy per unit volume

Which of the following is measure of stiffness? a) Modulus of elasticity b) Modulus of plasticity c) Resilience d) Toughness

Description : Which of the following is measure of stiffness? a) Modulus of elasticity b) Modulus of plasticity c) Resilience d) Toughness

Last Answer : a) Modulus of elasticity

Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is proportional to D3(D = mean coil diameter) or d4(d = wire diameter) (C) Crushing load or columns is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Description : Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is ... is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Last Answer : (C) Crushing load or columns is less than the buckling load

Distinguish between Young’s modulus, bulk modulus and modulus of rigidity.

Description : Distinguish between Young’s modulus, bulk modulus and modulus of rigidity.

Last Answer : Distinguish between Young’s modulus, bulk modulus and modulus of rigidity.

The modulus of rigidity is the ratio of (1) Longitudinal stress to longitudinal strain (2) Volume stress to volume strain (3) Shearing stress to shearing strain (4) Tensile stress to tensile strain

Description : The modulus of rigidity is the ratio of (1) Longitudinal stress to longitudinal strain (2) Volume stress to volume strain (3) Shearing stress to shearing strain (4) Tensile stress to tensile strain

Last Answer : (3) Shearing stress to shearing strain Explanation: In materials science, shear modulus or modulus of rigidity, denoted by G, or sometimes S , is defined as the ratio of shear stress to the shear ... the case of an object that's shaped like a rectangular prism, it will deform into a parallelepiped.

While Young's modulus ‘E’ relates to change in length and bulk modulus ‘K’ relates to change in volume, modulus of rigidity ‘G’ relates to change in: A. weight B. density C. shape D. temperature

Description : While Young's modulus ‘E’ relates to change in length and bulk modulus ‘K’ relates to change in volume, modulus of rigidity ‘G’ relates to change in: A. weight B. density C. shape D. temperature

Last Answer : . shape

Which of the following relation is correct regarding free torsional vibrations of a single motor system? a) Independent of modulus of rigidity b) Independent of polar moment of inertia c) Dependent on mass moment of inertia d) Independent of length of shaft

Description : Which of the following relation is correct regarding free torsional vibrations of a single motor system? a) Independent of modulus of rigidity b) Independent of polar moment of inertia c) Dependent on mass moment of inertia d) Independent of length of shaft

Last Answer : c) Dependent on mass moment of inertia

The ratio of shear stress and shear strain of an elastic material, is (A) Modulus of Rigidity (B) Shear Modulus (C) Modulus of Elasticity (D) Both (a) and (b)

Description : The ratio of shear stress and shear strain of an elastic material, is  (A) Modulus of Rigidity  (B) Shear Modulus  (C) Modulus of Elasticity  (D) Both (a) and (b) 

Last Answer : (D) Both (a) and (b) 

In a shaft, the shear stress is not directly proportional to (A) Radius of the shaft (B) Angle of twist (C) Length of the shaft (D) Modulus of rigidity

Description : In a shaft, the shear stress is not directly proportional to  (A) Radius of the shaft  (B) Angle of twist  (C) Length of the shaft  (D) Modulus of rigidity

Last Answer : (C) Length of the shaft

Pick up the incorrect statement from the following: The torsional resistance of a shaft is directly proportional to (A) Modulus of rigidity (B) Angle of twist (C) Reciprocal of the length of the shaft (D) Moment of inertia of the shaft section

Description : Pick up the incorrect statement from the following: The torsional resistance of a shaft is directly  proportional to  (A) Modulus of rigidity  (B) Angle of twist  (C) Reciprocal of the length of the shaft  (D) Moment of inertia of the shaft section 

Last Answer : (D) Moment of inertia of the shaft section 

If E, N, K and 1/m are modulus of elasticity, modulus of rigidity. Bulk modulus and Poisson ratio of the material, the following relationship holds good (A) E = 3K (1 - 2/m) (B) E = 2N (1 + 1/m) (C) (3/2)K (1 - 2/m) = N (1 + 1/m) (D) All the above

Description : If E, N, K and 1/m are modulus of elasticity, modulus of rigidity. Bulk modulus and Poisson ratio of  the material, the following relationship holds good  (A) E = 3K (1 - 2/m)  (B) E = 2N (1 + 1/m)  (C) (3/2)K (1 - 2/m) = N (1 + 1/m)  (D) All the above 

Last Answer : (D) All the above 

For a given material Young's modulus is 200 GN/m2 and modulus of rigidity is 80 GN/m2 . The value of Poisson's ratio is (A) 0.15 (B) 0.20 (C) 0.25 (D) 0.30

Description : For a given material Young's modulus is 200 GN/m2 and modulus of rigidity is 80 GN/m2 . The value of Poisson's ratio is (A) 0.15 (B) 0.20 (C) 0.25 (D) 0.30

Last Answer : (C) 0.25

A closely coiled helical spring of radius R, contains n turns and is subjected to an axial load W. If the radius of the coil wire is r and modulus of rigidity of the coil material is C, the deflection of the coil is (A) WR3n/Cr4 (B) 2WR3n/Cr4 (C) 3WR3n/Cr4 (D) 4WR3n/Cr

Description : A closely coiled helical spring of radius R, contains n turns and is subjected to an axial load W. If  the radius of the coil wire is r and modulus of rigidity of the coil material is C, the deflection of the  coil is  (A) WR3n/Cr4 (B) 2WR3n/Cr4 (C) 3WR3n/Cr4 (D) 4WR3n/Cr

Last Answer : (D) 4WR3n/Cr

A closely coiled helical spring of radius R, contains n turns and is subjected to an axial loadW. If the radius of the coil wire is r and modulus of rigidity of the coil material is C, the stress developed in the helical spring is (A) WR/ 3 (B) 2WR/ 3 (C) 2WR/ 2 (D) 4WR/ 2

Description : A closely coiled helical spring of radius R, contains n turns and is subjected to an axial loadW. If the radius of the coil wire is r and modulus of rigidity of the coil material is C, the stress developed in the helical spring is (A) WR/ 3 (B) 2WR/ 3 (C) 2WR/ 2 (D) 4WR/ 2

Last Answer : (B) 2WR/ 3

Which of the following relationships is correct for relating the three elastic constants of an isotropic elastic material (where, E = Young's modulus, G = Modulus of rigidity or shear modulus v = Poisson's ratio)? (A) E = 2G (1 + v) (B) E = G (1 + v) (C) E = G (1 + v)/2 (D) E = 2G (1 + 2v)

Description : Which of the following relationships is correct for relating the three elastic constants of an isotropic elastic material (where, E = Young's modulus, G = Modulus of rigidity or shear modulus v = Poisson's ratio)? (A) E = 2G (1 + v) (B) E = G (1 + v) (C) E = G (1 + v)/2 (D) E = 2G (1 + 2v)

Last Answer : (A) E = 2G (1 + v)

The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Last Answer : b) Spring stiffness

Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Description : Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Last Answer : b. 12.8 turns

The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Last Answer : (b) Spring stiffness

A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of rigidity is 80 GPa. The outside diameter (in mm) of the shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Last Answer : (a) 43 to 45

A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Last Answer : (d) 27/p

What is the product of sectional modulus and allowable bending stress called as? a. Moment of inertia b. Moment of rigidity c. Moment of resistance d. Radius of gyration

Description : What is the product of sectional modulus and allowable bending stress called as? a. Moment of inertia b. Moment of rigidity c. Moment of resistance d. Radius of gyration

Last Answer : c. Moment of resistance

The ratio of lateral strain to linear strain is called (a) Modulus of Elasticity (b) Modulus of Rigidity (c) Bulk Modulus (d) Poisson’s Ratio

Description : The ratio of lateral strain to linear strain is called (a) Modulus of Elasticity (b) Modulus of Rigidity (c) Bulk Modulus (d) Poisson’s Ratio

Last Answer : (d) Poisson’s Ratio

The relationship between Young’s modulus (E), Modulus of rigidity (C) and Bulk modulus (K) is given by a. E=9CK/(C+3K) b. E=9CK/(2C+3K) c. E=9CK/(3C+K) d. E=9CK/(C-3K)

Description : The relationship between Young’s modulus (E), Modulus of rigidity (C) and Bulk modulus (K) is given by a. E=9CK/(C+3K) b. E=9CK/(2C+3K) c. E=9CK/(3C+K) d. E=9CK/(C-3K)

Last Answer : a. E=9CK/(C+3K)

Modulus of rigidity is (a)Tensile stress / Tensile strain (a)Shear stress / Shear strain (a)Tensile stress / Shear strain (a)Shear stress / Tensile strain

Description : Modulus of rigidity is (a)Tensile stress / Tensile strain (a)Shear stress / Shear strain (a)Tensile stress / Shear strain (a)Shear stress / Tensile strain

Last Answer : (a)Shear stress / Shear strain

The modulus of rigidity is the ratio of (1) longitudinal stress to longitudinal strain (2) Volume stress to volume strain (3) shearing stress to shearing strain (4) tensile stress to tensile strain

Description : The modulus of rigidity is the ratio of (1) longitudinal stress to longitudinal strain (2) Volume stress to volume strain (3) shearing stress to shearing strain (4) tensile stress to tensile strain

Last Answer : shearing stress to shearing strain

Define modulus of rigidity and bulk Modulus.

Description : Define modulus of rigidity and bulk Modulus.

Last Answer : Bulk Modulus (K): When a body is subjected to three mutually perpendicular like stresses of same intensity then the ratio of direct stress and the corresponding volumetric strain of the body is constant and is ... (G): It is ratio of shear stress to shear strain, is called as Modulus of Rigidity. 

Resilience of a bolt can be increased by increasing its (A) Length (B) Shank diameter (C) Head diameter (D) None of these

Description : Resilience of a bolt can be increased by increasing its (A) Length (B) Shank diameter (C) Head diameter (D) None of these

Last Answer : (A) Length

Secondary stresses may be set up in frame due to any of the following reasons EXCEPT a.members not being straight b.self-weight of the members c.eccentricity of connections d.rigidity of the members e.107 dynes

Description : Secondary stresses may be set up in frame due to any of the following reasons EXCEPT a.members not being straight b.self-weight of the members c.eccentricity of connections d.rigidity of the members e.107 dynes

Last Answer : d. rigidity of the members

The dimensions of modulus of elasticity are a.MLT-2 b.107 dynes c.MLT-1 d.ML-2T-1 e.ML-1T-2

Description : The dimensions of modulus of elasticity are a.MLT-2 b.107 dynes c.MLT-1 d.ML-2T-1 e.ML-1T-2

Last Answer : e. ML-1T-2

Have you ever experienced a time in your life that required serious emotional resilience?

Description : Have you ever experienced a time in your life that required serious emotional resilience?

Last Answer : I think a lot of my life has been this way but especially the last 3 months at 35 weeks pregnant, I broke my leg, had to quit my job, 2 weeks later, my husband got laid off and a ... crying in the bathtub, by worrying, by sticking to my gut instincts with my husband, i can handle anything, truly

What evidence does Coutu use to support her claim that improvisation requires resilience?

Description : What evidence does Coutu use to support her claim that improvisation requires resilience?

Last Answer : The evidence Diane Coutu uses to support her claim that improvisation requires resilience is within the arena of personal capabilities or company rules, and the ability to solve problems without ... based on testimonials by people who have gone through such experiences, and psychological research.

__________ of SBR is adversely affected, if more quantity of styrene is added to butadiene during its co-polymerisation to produce SBR. (A) Percent elongation (B) Resilience (C) Freezing point (D) Strength

Description : __________ of SBR is adversely affected, if more quantity of styrene is added to butadiene during its co-polymerisation to produce SBR. (A) Percent elongation (B) Resilience (C) Freezing point (D) Strength

Last Answer : (B) Resilience

Silico-manganese steels (containing 0.7% Mn, 0.5% C and 2% Si) (A) Do not require heat treatment for any of its applications (B) Are used for leaf and coiled springs (C) Do not have good resilience properties (D) Is tempered at 850°C

Description : Silico-manganese steels (containing 0.7% Mn, 0.5% C and 2% Si) (A) Do not require heat treatment for any of its applications (B) Are used for leaf and coiled springs (C) Do not have good resilience properties (D) Is tempered at 850°C

Last Answer : (B) Are used for leaf and coiled springs

Slow and progressive deformation of a material with time under constant stress is called (A) Creep (B) Erosion (C) Resilience (D) None of these

Description : Slow and progressive deformation of a material with time under constant stress is called (A) Creep (B) Erosion (C) Resilience (D) None of these

Last Answer : (A) Creep

The ability of a material to absorb energy in the elastic range is a measure of its (A) Toughness (B) Resilience (C) Malleability (D) Brittleness

Description : The ability of a material to absorb energy in the elastic range is a measure of its (A) Toughness (B) Resilience (C) Malleability (D) Brittleness

Last Answer : (B) Resilience

Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience

Description : Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience

Last Answer : (B) Toughness

The ability of a material to offer resistance to scratching or indentation is a measure of its (A) Brittleness (B) Toughness (C) Hardness (D) Resilience

Description : The ability of a material to offer resistance to scratching or indentation is a measure of its (A) Brittleness (B) Toughness (C) Hardness (D) Resilience

Last Answer : (C) Hardness

Amount of energy that a material can absorb before its fracture is a measure of its (A) Toughness (B) Resilience (C) Malleability

Description : Amount of energy that a material can absorb before its fracture is a measure of its (A) Toughness (B) Resilience (C) Malleability

Last Answer : (A) Toughness

Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal of load c) Ability of material to absorb energy when deformed plastically d) None of the mentioned

Description : Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal ... c) Ability of material to absorb energy when deformed plastically d) None of the mentioned

Last Answer : a) Ability of material to absorb energy when deformed elastically

Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded. a) Elastically b) Plastically c) Up to fracture point d) None of the listed

Description : Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded. a) Elastically b) Plastically c) Up to fracture point d) None of the listed

Last Answer : a) Elastically

Resilience under principal tensile stresses σ1 and σ2 is (a) (1/2E)( σ1 2 + σ2 2 –μ σ1 σ2) (b) (1/2E)( σ1 2 + σ2 2 –4μ σ1 σ2) (c) (1/2E)( σ1 2 + σ2 2 –2μ σ1 σ2) (d) None

Description : Resilience under principal tensile stresses σ1 and σ2 is (a) (1/2E)( σ1 2 + σ2 2 –μ σ1 σ2) (b) (1/2E)( σ1 2 + σ2 2 –4μ σ1 σ2) (c) (1/2E)( σ1 2 + σ2 2 –2μ σ1 σ2) (d) None

Last Answer : (c) (1/2E)( σ1 2 + σ2 2 –2μ σ1 σ2)

Resilience under principal tensile stresses σ1 and σ2 is (a) (1/2E)( σ1 2 + σ2 2 –3μ σ1 σ2) (b) (1/2E)( σ1 2 + σ2 2 –4μ σ1 σ2) (c) (1/2E)( σ1 2 + σ2 2 –5μ σ1 σ2) (d) None

Description : Resilience under principal tensile stresses σ1 and σ2 is (a) (1/2E)( σ1 2 + σ2 2 –3μ σ1 σ2) (b) (1/2E)( σ1 2 + σ2 2 –4μ σ1 σ2) (c) (1/2E)( σ1 2 + σ2 2 –5μ σ1 σ2) (d) None

Last Answer : (d) None

Resilience under principal tensile stresses σ1 and σ2 is (a) (1/2E)( σ1 2 + σ2 2 –3μ σ1 σ2) (b) (1/2E)( σ1 2 + σ2 2 –4μ σ1 σ2) (c) (1/2E)( σ1 2 + σ2 2 –5μ σ1 σ2) (d) None

Description : Resilience under principal tensile stresses σ1 and σ2 is (a) (1/2E)( σ1 2 + σ2 2 –3μ σ1 σ2) (b) (1/2E)( σ1 2 + σ2 2 –4μ σ1 σ2) (c) (1/2E)( σ1 2 + σ2 2 –5μ σ1 σ2) (d) None

Last Answer : (d) None

The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Description : The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Last Answer : d) Fatigue

Which of the following property is essential for spring materials? (A) Stiffness (B) Ductility (C) Resilience (D) Plasticity

Description : Which of the following property is essential for spring materials? (A) Stiffness (B) Ductility (C) Resilience (D) Plasticity

Last Answer : (C) Resilience

An ecosystem which can be easily damaged but can recover after some time if damaging effect stops will be having (a) low stability and high resilience (b) high stability and low resilience (c) low stability and low resilience (d) high stability and high resilience.

Description : An ecosystem which can be easily damaged but can recover after some time if damaging effect stops will be having (a) low stability and high resilience (b) high stability and low resilience (c) low stability and low resilience (d) high stability and high resilience.

Last Answer : (a) low stability and high resilience