What is the difference between proof resilience and modulus of resilience ?

What is the difference between proof resilience and modulus of resilience ?
by

1 Answer

Answer :

Proof resilience is the maximum strain energy that can be stored in a material without permanent
deformation. Modulus of resilience is the maximum strain energy stored in a material per unit volume.
by

Related questions

Explain difference between modulus of resilience and modulus of rigidity ?

Description : Explain difference between modulus of resilience and modulus of rigidity ?

Last Answer : Modulus of resilience is the maximum strain energy stored in a material per unit volume and modulus of rigidity is the ratio of shearing stress to the shearing strain within the elastic limit.

Modulus of resilience is defined as a) Strain energy per unit volume b) Strain energy per unit area c) Independent of strain energy d) None of the mentioned

Description : Modulus of resilience is defined as a) Strain energy per unit volume b) Strain energy per unit area c) Independent of strain energy d) None of the mentioned

Last Answer : a) Strain energy per unit volume

Which of the following is measure of stiffness? a) Modulus of elasticity b) Modulus of plasticity c) Resilience d) Toughness

Description : Which of the following is measure of stiffness? a) Modulus of elasticity b) Modulus of plasticity c) Resilience d) Toughness

Last Answer : a) Modulus of elasticity

Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is proportional to D3(D = mean coil diameter) or d4(d = wire diameter) (C) Crushing load or columns is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Description : Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is ... is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Last Answer : (C) Crushing load or columns is less than the buckling load

In the relation ( T/J = Gθ/L = τ/ R), the letter G denotes modulus of ______ a. elasticity b. plasticity c. rigidity d. resilience

Description : In the relation ( T/J = Gθ/L = τ/ R), the letter G denotes modulus of ______ a. elasticity b. plasticity c. rigidity d. resilience

Last Answer : c. rigidity

The greatest load which a spring can carry without getting permanently distorted, is called (A) Stiffness (B) Proof resilience (C) Proof stress (D) Proof load

Description : The greatest load which a spring can carry without getting permanently distorted, is called (A) Stiffness (B) Proof resilience (C) Proof stress (D) Proof load 

Last Answer : (D) Proof load 

The strain energy stored in a spring when subjected to greatest load without being permanently distorted, is called (A) Stiffness (B) Proof resilience (C) Proof stress (D) Proof load

Description : The strain energy stored in a spring when subjected to greatest load without being permanently  distorted, is called  (A) Stiffness  (B) Proof resilience  (C) Proof stress  (D) Proof load

Last Answer : (B) Proof resilience 

The load on a spring per unit deflection, is called (A) Stiffness (B) Proof resilience (C) Proof stress (D) Proof load

Description : The load on a spring per unit deflection, is called  (A) Stiffness  (B) Proof resilience  (C) Proof stress  (D) Proof load

Last Answer : (A) Stiffness 

Define resilience and Proof resilience.

Description : Define resilience and Proof resilience.

Last Answer : Resilience: Resilience is the ability of material to absorb energy when it is deformed elastically and release that energy upon unloading.  Proof Resilience: Proof resilience is defined as the maximum energy that can be absorbed within elastic limit without creating permanent deformation.

Resilience of a bolt can be increased by increasing its (A) Length (B) Shank diameter (C) Head diameter (D) None of these

Description : Resilience of a bolt can be increased by increasing its (A) Length (B) Shank diameter (C) Head diameter (D) None of these

Last Answer : (A) Length

The dimensions of modulus of elasticity are a.MLT-2 b.107 dynes c.MLT-1 d.ML-2T-1 e.ML-1T-2

Description : The dimensions of modulus of elasticity are a.MLT-2 b.107 dynes c.MLT-1 d.ML-2T-1 e.ML-1T-2

Last Answer : e. ML-1T-2

Have you ever experienced a time in your life that required serious emotional resilience?

Description : Have you ever experienced a time in your life that required serious emotional resilience?

Last Answer : I think a lot of my life has been this way but especially the last 3 months at 35 weeks pregnant, I broke my leg, had to quit my job, 2 weeks later, my husband got laid off and a ... crying in the bathtub, by worrying, by sticking to my gut instincts with my husband, i can handle anything, truly

What evidence does Coutu use to support her claim that improvisation requires resilience?

Description : What evidence does Coutu use to support her claim that improvisation requires resilience?

Last Answer : The evidence Diane Coutu uses to support her claim that improvisation requires resilience is within the arena of personal capabilities or company rules, and the ability to solve problems without ... based on testimonials by people who have gone through such experiences, and psychological research.

__________ of SBR is adversely affected, if more quantity of styrene is added to butadiene during its co-polymerisation to produce SBR. (A) Percent elongation (B) Resilience (C) Freezing point (D) Strength

Description : __________ of SBR is adversely affected, if more quantity of styrene is added to butadiene during its co-polymerisation to produce SBR. (A) Percent elongation (B) Resilience (C) Freezing point (D) Strength

Last Answer : (B) Resilience

Silico-manganese steels (containing 0.7% Mn, 0.5% C and 2% Si) (A) Do not require heat treatment for any of its applications (B) Are used for leaf and coiled springs (C) Do not have good resilience properties (D) Is tempered at 850°C

Description : Silico-manganese steels (containing 0.7% Mn, 0.5% C and 2% Si) (A) Do not require heat treatment for any of its applications (B) Are used for leaf and coiled springs (C) Do not have good resilience properties (D) Is tempered at 850°C

Last Answer : (B) Are used for leaf and coiled springs

Slow and progressive deformation of a material with time under constant stress is called (A) Creep (B) Erosion (C) Resilience (D) None of these

Description : Slow and progressive deformation of a material with time under constant stress is called (A) Creep (B) Erosion (C) Resilience (D) None of these

Last Answer : (A) Creep

The ability of a material to absorb energy in the elastic range is a measure of its (A) Toughness (B) Resilience (C) Malleability (D) Brittleness

Description : The ability of a material to absorb energy in the elastic range is a measure of its (A) Toughness (B) Resilience (C) Malleability (D) Brittleness

Last Answer : (B) Resilience

Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience

Description : Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience

Last Answer : (B) Toughness

The ability of a material to offer resistance to scratching or indentation is a measure of its (A) Brittleness (B) Toughness (C) Hardness (D) Resilience

Description : The ability of a material to offer resistance to scratching or indentation is a measure of its (A) Brittleness (B) Toughness (C) Hardness (D) Resilience

Last Answer : (C) Hardness

Amount of energy that a material can absorb before its fracture is a measure of its (A) Toughness (B) Resilience (C) Malleability

Description : Amount of energy that a material can absorb before its fracture is a measure of its (A) Toughness (B) Resilience (C) Malleability

Last Answer : (A) Toughness

Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal of load c) Ability of material to absorb energy when deformed plastically d) None of the mentioned

Description : Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal ... c) Ability of material to absorb energy when deformed plastically d) None of the mentioned

Last Answer : a) Ability of material to absorb energy when deformed elastically

Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded. a) Elastically b) Plastically c) Up to fracture point d) None of the listed

Description : Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded. a) Elastically b) Plastically c) Up to fracture point d) None of the listed

Last Answer : a) Elastically

Resilience under principal tensile stresses σ1 and σ2 is (a) (1/2E)( σ1 2 + σ2 2 –μ σ1 σ2) (b) (1/2E)( σ1 2 + σ2 2 –4μ σ1 σ2) (c) (1/2E)( σ1 2 + σ2 2 –2μ σ1 σ2) (d) None

Description : Resilience under principal tensile stresses σ1 and σ2 is (a) (1/2E)( σ1 2 + σ2 2 –μ σ1 σ2) (b) (1/2E)( σ1 2 + σ2 2 –4μ σ1 σ2) (c) (1/2E)( σ1 2 + σ2 2 –2μ σ1 σ2) (d) None

Last Answer : (c) (1/2E)( σ1 2 + σ2 2 –2μ σ1 σ2)

Resilience under principal tensile stresses σ1 and σ2 is (a) (1/2E)( σ1 2 + σ2 2 –3μ σ1 σ2) (b) (1/2E)( σ1 2 + σ2 2 –4μ σ1 σ2) (c) (1/2E)( σ1 2 + σ2 2 –5μ σ1 σ2) (d) None

Description : Resilience under principal tensile stresses σ1 and σ2 is (a) (1/2E)( σ1 2 + σ2 2 –3μ σ1 σ2) (b) (1/2E)( σ1 2 + σ2 2 –4μ σ1 σ2) (c) (1/2E)( σ1 2 + σ2 2 –5μ σ1 σ2) (d) None

Last Answer : (d) None

Resilience under principal tensile stresses σ1 and σ2 is (a) (1/2E)( σ1 2 + σ2 2 –3μ σ1 σ2) (b) (1/2E)( σ1 2 + σ2 2 –4μ σ1 σ2) (c) (1/2E)( σ1 2 + σ2 2 –5μ σ1 σ2) (d) None

Description : Resilience under principal tensile stresses σ1 and σ2 is (a) (1/2E)( σ1 2 + σ2 2 –3μ σ1 σ2) (b) (1/2E)( σ1 2 + σ2 2 –4μ σ1 σ2) (c) (1/2E)( σ1 2 + σ2 2 –5μ σ1 σ2) (d) None

Last Answer : (d) None

The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Description : The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Last Answer : d) Fatigue

Which of the following property is essential for spring materials? (A) Stiffness (B) Ductility (C) Resilience (D) Plasticity

Description : Which of the following property is essential for spring materials? (A) Stiffness (B) Ductility (C) Resilience (D) Plasticity

Last Answer : (C) Resilience

An ecosystem which can be easily damaged but can recover after some time if damaging effect stops will be having (a) low stability and high resilience (b) high stability and low resilience (c) low stability and low resilience (d) high stability and high resilience.

Description : An ecosystem which can be easily damaged but can recover after some time if damaging effect stops will be having (a) low stability and high resilience (b) high stability and low resilience (c) low stability and low resilience (d) high stability and high resilience.

Last Answer : (a) low stability and high resilience

The men and women of South Africa risked their lives to: (a) struggle (b) torture without breaking (c) get freedom from apartheid (d) resilience

Description : The men and women of South Africa risked their lives to: (a) struggle (b) torture without breaking (c) get freedom from apartheid (d) resilience

Last Answer : (c) get freedom from apartheid

What business outcomes might be expected from moving to the cloud? 1. Improved agility 2. Operational resilience 3. Sustainable IT A. 1 only B. 2 Only C. All above D. 2 and 3 only

Description : What business outcomes might be expected from moving to the cloud? 1. Improved agility 2. Operational resilience 3. Sustainable IT A. 1 only B. 2 Only C. All above D. 2 and 3 only

Last Answer : All above

If a soil undergoes a change in shape and volume by application of external loads over it, but recovers its shape and volume immediately after removal of the load, the property of the soil is said to be (A) Resilience of soils (B) Elasticity of soils (C) Compressibility of soils (D) None of these

Description : If a soil undergoes a change in shape and volume by application of external loads over it, but recovers its shape and volume immediately after removal of the load, the property of the soil is said to ... Resilience of soils (B) Elasticity of soils (C) Compressibility of soils (D) None of these

Last Answer : Answer: Option B

The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Description : The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Last Answer : (A) Resilience

The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Description : The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Last Answer : (A) Resilience

A material subjected __________ must have high resilience. (A) Shock loading (B) Vibration (C) Fatigue (D) Tension

Description : A material subjected __________ must have high resilience. (A) Shock loading (B) Vibration (C) Fatigue (D) Tension

Last Answer : (A) Shock loading

Most important property of steels for use in automobile bodies is the (A) Formability (B) Yield strength (C) Toughness (D) Resilience

Description : Most important property of steels for use in automobile bodies is the (A) Formability (B) Yield strength (C) Toughness (D) Resilience

Last Answer : (A) Formability

The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit

Description : The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit

Last Answer : D) Endurance limit

Presence of nickel & chromium in steel does not raise its (A) Elastic limit (B) Machining properties (C) Ductility (D) Resilience Answer: Option A

Description : Presence of nickel & chromium in steel does not raise its (A) Elastic limit (B) Machining properties (C) Ductility (D) Resilience Answer: Option A

Last Answer : Option A

Resilience of spring is (a) Strain energy per unit length (b) Strain energy per unit area (c) Strain energy per unit mass (d) None

Description : Resilience of spring is (a) Strain energy per unit length (b) Strain energy per unit area (c) Strain energy per unit mass (d) None

Last Answer : (d) None

The shafts are designed on the basis of a. strength and rigidity. b. ductility. c. malleablility. d. resilience.

Description : The shafts are designed on the basis of a. strength and rigidity. b. ductility. c. malleablility. d. resilience.

Last Answer : a. strength and rigidity.

Class 12 | Maths | Complex Numbers | Simplify the following complex numbers and find their modulus.

Description : Class 12 | Maths | Complex Numbers | Simplify the following complex numbers and find their modulus.

Last Answer : Class 12 | Maths | Complex Numbers | Simplify the following complex numbers and find their modulus.

Class 12 | Maths | Complex Numbers | Simplify -2i ( 3 + i )( 2 + 4i )( 1 + i ) and obtain the modulus of that complex number.

Description : Class 12 | Maths | Complex Numbers | Simplify -2i ( 3 + i )( 2 + 4i )( 1 + i ) and obtain the modulus of that complex number.

Last Answer : Solution :

Class 12 | Maths | Complex Numbers | Express the complex numbers modulus-amplitude form - √3 + i

Description : Class 12 | Maths | Complex Numbers | Express the complex numbers modulus-amplitude form  - √3 + i

Last Answer : Solution : 

I need ways to test/get data about homemade plastics. What can I do with Flexural Strength and Flexural Modulus...

Description : I need ways to test/get data about homemade plastics. What can I do with Flexural Strength and Flexural Modulus...

Last Answer : answer:Strength is how strong a material is – basically breaking load. Modulus is how flexible or stretchy a material is. Does not matter if the test coupon breaks or not. Think of uncooked spaghetti vs rubber band.

What is the SI unit of Young’s modulus of elasticity? -Do You Know?

Description : What is the SI unit of Young’s modulus of elasticity? -Do You Know?

Last Answer : answer:

What is modulus ?

Description : What is modulus ?

Last Answer : The maximum number that the counter can count is called modulus or mode number. If there are n flip flops in a counter , its mode number is 2 n .

What is Young’s modulus? Describe an experiment to find out Young’s modulus of material

Description : What is Young’s modulus? Describe an experiment to find out Young’s modulus of material

Last Answer : What is Young’s modulus? Describe an experiment to find out Young’s modulus of material in the form of a long straight wire.

Distinguish between Young’s modulus, bulk modulus and modulus of rigidity.

Description : Distinguish between Young’s modulus, bulk modulus and modulus of rigidity.

Last Answer : Distinguish between Young’s modulus, bulk modulus and modulus of rigidity.

What is Young’s modulus of a rigid body?

Description : What is Young’s modulus of a rigid body?

Last Answer : What is Young’s modulus of a rigid body?

If S is stress, Y is Young’s modulus of material of a wire, the energy stored in the wire per unit volume is (a) 2Y/S (b) S/2Y (c) 2S2Y (d) S2/2Y

Description : If S is stress, Y is Young’s modulus of material of a wire, the energy stored in the wire per unit volume is (a) 2Y/S (b) S/2Y (c) 2S2Y (d) S2/2Y

Last Answer : Ans:(d)

Dimension of modulus of elasticity is (a) ML–2T–2 (b) M–1L–1T–2 (c) ML–1T–2 (d) ML–1T–1

Description : Dimension of modulus of elasticity is (a) ML–2T–2 (b) M–1L–1T–2 (c) ML–1T–2 (d) ML–1T–1

Last Answer : Ans:(c)