Turbine-Generator Lubrication Oil System Function

Turbine-Generator Lubrication Oil System Function
by

1 Answer

Answer :

Turbine-Generator Lubrication Oil System Function
For large turbine-generators forced lubrication system and water cooling system should be continuously required during the operation of the turbine-generator and during coast down. The main function of lubrication system is to:
Function of Lubrication System:
Lubrication system reduces the friction between the moving parts and static parts of the turbine generator which can occur at journal bearings and thrust bearings. Efficient lubrication system reduces the wear and tear; increases the efficiency.
Lubrication system acts as cooling medium and removes the heat generated at the moving parts due to friction.
Interruption to lubrication system supplying the turbine-generator damages the bearings and the rotating parts due to high friction. When the unit is under shut down condition, it must be continue to rotated (during shutdown condition turbine-generator set is rotated at 1 rpm speed by motor drive system) to assure uniform cooling in order to prevent thermal bowing (eccentricity) of the rotating element.
For a typical power plant Turbine-Generator unit, lubrication motors consists of the following:
Shaft-driven main bearing oil pump (MBOP)
AC motor-driven turbine bearing oil pump (TBOP)
DC emergency bearing oil pump (EBOP)
Shaft driven main bearing oil pump is mounted on the turbine-generator shaft and delivers lubrication oil for cooling during normal operation of the plant. During plant start up or during plant shutdown condition, shaft driven main bearing oil pump cannot have sufficient pressure to deliver the lubrication oil to the system. Therefore AC motor-driven turbine oil pump provides lubrication oil during start up condition and also during hut down condition. These ac motors are backed with dc emergency bearing oil pump, which is supplied power by station battery and starts immediately when the oil pressure is low. A second backup dc pumps are sometimes provided.
by

Related questions

What is the logic in lubrication oil pump system?

Description : What is the logic in lubrication oil pump system?

Last Answer : Normally main oil pump (MOP) will feed the required lub oil to turbine governor and lubrication. If the pressure drops to 5.3 kg/cm2 6.6 kV 373 kW Aux. Oil Pump will start. If further pressure falls to

Where oil lubrication is preferred over grease lubrication?

Description : Where oil lubrication is preferred over grease lubrication?

Last Answer : a) Determined by speed and operating temperature. b) Oil lubrication recommended. c) When speed and temperature is high. d) When heat to be conducted away from bearing. e) When adjacent machine ... High viscous oil for low speed machine, low viscous oil for high speed machine. g) At temp

What is the purpose of lubrication oil?

Description : What is the purpose of lubrication oil?  

Last Answer : Keep oil film in bearings, avoid metal to metal contact between bottom of journal and bearings avoid damage to bearings by lubricating the bearings. This also removes heat from that part. 

The propeller shaft speed in a turbo-electric, synchronous, propulsion drive motor is changed by varying the __________. A. turbine speed B. number of motor poles C. field strength of the generator D. field strength of the motor

Description : The propeller shaft speed in a turbo-electric, synchronous, propulsion drive motor is changed by varying the __________. A. turbine speed B. number of motor poles C. field strength of the generator D. field strength of the motor

Last Answer : Answer: A

Write critical speeds of turbine generator?

Description : Write critical speeds of turbine generator?  

Last Answer : Generator rotor 1st critical speed 1283 rpm 2nd critical speed 3600 rpm Combined turbine generator 1st critical speed 1938 rpm 2nd critical speed 2120 rpm 3rd critical speed 2385 rpm 4th critical speed 2837 rpm 

What are the futures of turbine generator?

Description : What are the futures of turbine generator? 

Last Answer : a. Low heat drop b. Moisture control (HP-0.26%, LP-3%.) c. Turbine governing system d. 70% steam dumping to the condenser to avoid reactor trip. e. Gland sealing f. LP exhaust hood cooling g. Generator stator and rotor cooling h. Hydrogen sealing i. Static excitation 

What is the purpose of TOPP (turbine oil purification plant)?

Description : What is the purpose of TOPP (turbine oil purification plant)? 

Last Answer : The purpose of TOPP is to remove the water ingress in turbine oil system from the gland leaks, cooler leakage, and solid metal particles, which are produced due to rust, wear of bearings and to normalize the ... capacity of TOPP is, for solids - 5 microns and for water - 300 to 500 parts per milli.

How turbine oil purification is achieved?

Description : How turbine oil purification is achieved?

Last Answer : Oil purification is achieved by centrifugal operation.  

The failure of ball bearings used in electric motors can result from _____________. A. failure to clean the bearing before repacking B. failure to maintain proper alignment C. excess lubrication forcing the bearing full of grease and eliminating all areas of expansion D. all of the above

Description : The failure of ball bearings used in electric motors can result from _____________. A. failure to clean the bearing before repacking B. failure to maintain proper alignment C. excess lubrication forcing the bearing full of grease and eliminating all areas of expansion D. all of the above

Last Answer : Answer: D

If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform a 'high pot' test to determine the condition of the insulation C. water wash the motor and controller to remove any salt that may interfere with smooth operation D. check run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Description : If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform ... run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Last Answer : Answer: D

The only point in the steering stand shown in the illustration which needs periodic lubrication is the ______________. EL-0098 A. repeater assembly ball bearings B. steering wheel bearing C. operation selector switch D. course selector pointer

Description : The only point in the steering stand shown in the illustration which needs periodic lubrication is the ______________. EL-0098 A. repeater assembly ball bearings B. steering wheel bearing C. operation selector switch D. course selector pointer

Last Answer : Answer: B

During its operation, loud buzzing and resultant welding of contacts of a magnetic relay may be caused by __________. A. overheating of the contactor coil B. low voltage on the operating coil C. low insulation resistance to ground D. lubrication of the contact bearing points

Description : During its operation, loud buzzing and resultant welding of contacts of a magnetic relay may be caused by __________. A. overheating of the contactor coil B. low voltage on the operating coil C. low insulation resistance to ground D. lubrication of the contact bearing points

Last Answer : Answer: B

How does the hydrostatic lubrication differ from hydrodynamic type?

Description : How does the hydrostatic lubrication differ from hydrodynamic type?

Last Answer : In hydrostatic lubrication which is used in slow speed turbines the lubricating oil is pressurised externally where as in hydrodynamic system it forms oil film by its speed which pushes the lubrication oil to form film.

What is meant by hydrodynamic film lubrication?

Description : What is meant by hydrodynamic film lubrication?

Last Answer : In high-speed turbines the lubricating oil will be at the sides and there is metal to metal contact when turbine at rest. When the turbine speeds up there is pressure pushing the oil through the ... the oil film breaks the barrier and it takes the load on itself. This is hydrodynamic lubrication. 

Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a ... explanation of A (c) A is true but R is false (d) A is false but R is true

Last Answer : (c) A is true but R is false

In hydrostatic bearings (A) The Oil film pressure is generated only by the rotation of the journal (B) The oil film is maintained by supplying oil under pressure (C) Do not require external supply of lubricant (D) Grease is used for lubrication

Description : In hydrostatic bearings (A) The Oil film pressure is generated only by the rotation of the journal (B) The oil film is maintained by supplying oil under pressure (C) Do not require external supply of lubricant (D) Grease is used for lubrication

Last Answer : (B) The oil film is maintained by supplying oil under pressure

How can I run a gas turbine power generator efficiently?

Description : How can I run a gas turbine power generator efficiently?

Last Answer : www.muellerenvironmental.com/documents/GER3567H.pdf discusses many factors affecting gas turbine efficiency. It specifically addresses GE turbines, but the factors discussed are relevant to all gas turbine power generators.

Once the condensate reaches the _____ , it becomes available to the boiler for recycling. • Condenser • Turbine • Boiler • Generator

Description : Once the condensate reaches the _____ , it becomes available to the boiler for recycling. • Condenser • Turbine • Boiler • Generator

Last Answer : • Boiler

Consider efficiencies of hydro-turbines and generators. If the efficiency of a hydro-turbine is 80% and the efficiency of a generator is 90%, what is the overall efficiency of the unit? w) 85% x) 72% y) 90% z) 70%

Description : Consider efficiencies of hydro-turbines and generators. If the efficiency of a hydro-turbine is 80% and the efficiency of a generator is 90%, what is the overall efficiency of the unit? w) 85% x) 72% y) 90% z) 70% 

Last Answer : ANSWER: X -- 72%

Why is a shaft coupler used between turbine and generator ?

Description : Why is a shaft coupler used between turbine and generator ?

Last Answer : For easy transmission torque or rotation angle and can also use for the protection of the safety devices shaft cannot be separated from the shaft during motion coupling will be damaged first so as avoid to the damaged of motor or other transmission parts.

A hydraulic turbine having rated speed of 250 rpm is connected to a synchronous generator. In order to

Description : A hydraulic turbine having rated speed of 250 rpm is connected to a synchronous generator. In order to produce power at 50 Hz, the number of poles required in the generator are (A) 6 (B) 12 (C) 16 (D) 24

Last Answer : A hydraulic turbine having rated speed of 250 rpm is connected to a synchronous generator. In order to produce power at 50 Hz, the number of poles required in the generator are 24

According to Coast Guard Regulation (46 CFR) for emergency power and lighting systems, which of the listed items is the only permissible starting aid for the emergency diesel generator engine? A. Ether B. Lube oil heater C. Jacket water heater D. Fuel oil heater

Description : According to Coast Guard Regulation (46 CFR) for emergency power and lighting systems, which of the listed items is the only permissible starting aid for the emergency diesel generator engine? A. Ether B. Lube oil heater C. Jacket water heater D. Fuel oil heater

Last Answer : Answer: C

Coast Guard Regulations (46 CFR) require that the emergency diesel generator engine shut down when _____________. A. lubricating oil pressure is lost B. the engine overspeeds dangerously C. fixed CO2 is released into the emergency diesel generator space D. all of the above

Description : Coast Guard Regulations (46 CFR) require that the emergency diesel generator engine shut down when _____________. A. lubricating oil pressure is lost B. the engine overspeeds dangerously C. fixed CO2 is released into the emergency diesel generator space D. all of the above

Last Answer : Answer: D

The main purpose of an electric space heater installed in a large AC generator is to _____________. A. keep the lube oil warm for quick starting B. prevent moisture from condensing in the windings when the machine is shutdown C. prevent the windings from becoming brittle D. prevent acidic pitting of the slip rings

Description : The main purpose of an electric space heater installed in a large AC generator is to _____________. A. keep the lube oil warm for quick starting B. prevent moisture from condensing in the ... is shutdown C. prevent the windings from becoming brittle D. prevent acidic pitting of the slip rings

Last Answer : Answer: B

Diesel generators #1 and #2 are operating in parallel at near full load capacity. Diesel generator #1 suddenly trips out mechanically due to low lube oil pressure. The reverse power relay functions properly and trips generator #1 electrically off the bo A. Start the emergency generator. B. Ascertain cause of the low lube oil pressure. C. Strip the board of all nonvital circuits. D. Secure alarms, reset reverse power relay, and restart #1 engine.

Description : Diesel generators #1 and #2 are operating in parallel at near full load capacity. Diesel generator #1 suddenly trips out mechanically due to low lube oil pressure. The reverse power relay functions ... all nonvital circuits. D. Secure alarms, reset reverse power relay, and restart #1 engine.

Last Answer : Answer: C

If the bearings of an electrical generator are failing more frequently than expected and the lubricating oil is sludging then you should ______________. A. check the connections to the output leads B. check the bearing insulating block on one end of the unit C. replace the bearing with a sealed roller type D. replace the thrust bearing of the prime mover

Description : If the bearings of an electrical generator are failing more frequently than expected and the lubricating oil is sludging then you should ______________. A. check the connections to the output leads B. ... replace the bearing with a sealed roller type D. replace the thrust bearing of the prime mover

Last Answer : Answer: B

The main purpose of an electric space heater installed in a large AC generator is to _____________. A. prevent the windings from becoming brittle B. prevent moisture from condensing in the windings during shutdown C. prevent acidic pitting of the slip rings D. keep the lube oil warm for quick starting

Description : The main purpose of an electric space heater installed in a large AC generator is to _____________. A. prevent the windings from becoming brittle B. prevent moisture from condensing in the windings during ... C. prevent acidic pitting of the slip rings D. keep the lube oil warm for quick starting

Last Answer : Answer: B

Why oil cannot be used instead of water in generator stator?

Description : Why oil cannot be used instead of water in generator stator?

Last Answer : Oil has high thermal capacity than gas, but low thermal capacity than water. Ability to absorb heat is also less than waters. High viscosity of oil causes linear flow and poor surface heat transfer in small ducts. Large pumping power required. 

State the factors, for the choice of electrical system for an aero turbine.

Description : State the factors, for the choice of electrical system for an aero turbine.

Last Answer : A:The choice of electrical system for an aero turbine is guided by three factors: Type of electrical output: dc, variable- frequency ac, and constant- frequency ac. Aero turbine ... energy output: in conjunction with battery or other form of storage, or interconnection with power grid.

What type of governing system used in turbine and what are the purposes of the system?

Description : What type of governing system used in turbine and what are the purposes of the system? 

Last Answer : Hydraulic governing system of centrifugal (speed) governer type is adopted in turbine. Sensitive oil pressure to actuate centrifugal governer is 6.1 kg/cm2 (max). At 6.7 kg/cm2 relief valve ... speeder gear from BPC signal. Once synchronised the grid frequency and speeder gear controls the speed. 

What is the purpose of turbine governing system?

Description : What is the purpose of turbine governing system?

Last Answer : Turbine governing system governs the speed of the turbine with the help of centrifugal governer. It reduces the steam inlet when turbine over speeds.  

State the factors, for the choice of electrical system for an aero turbine.

Description : State the factors, for the choice of electrical system for an aero turbine.

Last Answer : The choice of electrical system for an aero turbine is guided by three factors: Type of electrical output: dc, variablefrequency ac, and constant- frequency ac. Aero turbine rotational speed ... output: in conjunction with battery or other form of storage, or interconnection with power grid.

As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay #6 C. the RPM 'function generator' and 'thrust levers' have no control D. the 'E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Description : As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay ... E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Last Answer : Answer: C

Which power plant has minimum operating cost? a) Hydroelectric power plant b) Thermal power plant c) Nuclear power plant d) Gas Turbine Power Plant Ans: A 42. Which of the following have highest operating cost? a) Hydroelectric power plant b) Thermal power plant c) Nuclear power plant d) Solar electric power plant

Description : Which power plant has minimum operating cost? a) Hydroelectric power plant b) Thermal power plant c) Nuclear power plant d) Gas Turbine Power Plant Ans: A 42. Which of the following have ... a) Hydroelectric power plant b) Thermal power plant c) Nuclear power plant d) Solar electric power plant

Last Answer : Ans: B

What are the working fluids in gas turbine?

Description : What are the working fluids in gas turbine?

Last Answer : 1.Air 2.Helium 3.Argon 4.Carbon dioxide

Explain reaction turbine in terms of head:

Description : Explain reaction turbine in terms of head:

Last Answer : High head- Francis Medium head- Propeller Low head- Kaplan

State turbine governor setting.

Description : State turbine governor setting. 

Last Answer : On 2560 rpm turbine governor becomes effective and on 2760 rpm is turbine governor take over speed. 

What is the type turbine installed in KGS?

Description : What is the type turbine installed in KGS? 

Last Answer : Tandem compounded to expansion of steam, impulse reaction type.  

How shaft voltage produced by turbine?

Description : How shaft voltage produced by turbine? 

Last Answer : Due to un-symmetry in the flux path of core, non-uniform air gap, un-symmetry in the rotor magnetic field during short circuit in the rotor winding, causes voltage to develop across the ends of rotor shaft. 

How dearator pressure is maintained after turbine trip?

Description : How dearator pressure is maintained after turbine trip? 

Last Answer : Pegging steam is used to maintain dearator pressure after turbine trip.  

Explain the main difference between impulse and reaction turbine.

Description : Explain the main difference between impulse and reaction turbine. 

Last Answer : When the inlet pressure of steam to the turbine is equal to outlet pressure of steam from the turbine the turbine is called the impulse turbine. In this type the heat is added is very less. ... than the inlet pressure of the steam. There is reduction in pressure with the increase in kinetic energy.

What are the methods of removing moisture from turbine?

Description : What are the methods of removing moisture from turbine?

Last Answer : a. External method by moisture separator and reheater, which separates the moisture and reheates the steam. b. Internally by stainless steel mesh, which reduces moisture (water particles) to 1%. c. By main steam reheat. 

Explain the principle of working of impulse steam turbine.

Description : Explain the principle of working of impulse steam turbine. 

Last Answer : When steam enters the turbine it suffers a change in direction and momentum, which gives rise to the rotation of the turbine. There will be no drop in pressure in impulse steam turbine.  

Flue gases coming out from furnace is first going through a) Turbine b) Economizer c) Air pre-heater d) Chimney

Description : Flue gases coming out from furnace is first going through a) Turbine b) Economizer c) Air pre-heater d) Chimney

Last Answer : Ans: Economizer

Water hamming effect is occurs in a) Surge tank b) Penstock c) Turbine d) Reservoir

Description : Water hamming effect is occurs in a) Surge tank b) Penstock c) Turbine d) Reservoir

Last Answer : Ans: Penstock

Low head plants generally use (A) Pelton Turbines (B) Francis Turbine (C) Pelton or Francis Turbine (D) Kaplan Turbines

Description : Low head plants generally use (A) Pelton Turbines (B) Francis Turbine (C) Pelton or Francis Turbine (D) Kaplan Turbines

Last Answer : Ans: A In the hysterisis motor, the direction of rotation can be reversed by shifting the shaded pole region with respect to main pole. But not by changing supply lead because it has ac supply.