How dearator pressure is maintained after turbine trip?

How dearator pressure is maintained after turbine trip? 
by

1 Answer

Answer :

Pegging steam is used to maintain dearator pressure after turbine trip.  
by

Related questions

How dearator pressure is maintained?

Description : How dearator pressure is maintained?  

Last Answer : Dearator pressure is normally maintained by extraction steam.  

What are the functions of dearator?

Description : What are the functions of dearator?

Last Answer : Dearator removes non-condensable gases (O2), which gets added in the steam and it, mixes steam with the condensed water for feed water heating. This is a contact type feed water heater.  

Why water pressure is kept below the oil pressure? How it is maintained?

Description : Why water pressure is kept below the oil pressure? How it is maintained? 

Last Answer : Incase of a heat exchanger tube failure the water should not go inside the transformer. For this purpose the oil pressure is kept above the water pressure. 

How seal oil pressure is maintained?

Description : How seal oil pressure is maintained?

Last Answer : Differential pressure regulator maintains the seal oil pressure at 0.7 kg / cm2 higher than H2 pressure. 

You are testing the insulation in an AC generator with a megohmeter. The resistance value of a dry, clean winding will ____________. A. continue to rise as the test potential is maintained, becoming fairly steady as the leakage current stabilizes B. remain constant as the temperature of the windings increases C. continue to drop as the potential is maintained, becoming fairly steady after 5 to 7 minutes D. stabilize after approximately 2 to 4 minutes of fluctuation

Description : You are testing the insulation in an AC generator with a megohmeter. The resistance value of a dry, clean winding will ____________. A. continue to rise as the test potential is maintained, ... fairly steady after 5 to 7 minutes D. stabilize after approximately 2 to 4 minutes of fluctuation

Last Answer : Answer: A

Coast Guard Regulations (46 CFR) require that each alternating current generator arranged for parallel operation shall be provided with _____________. A. more than one means of excitation B. individual circuit fuses C. a high back-pressure trip D. a reverse-power trip

Description : Coast Guard Regulations (46 CFR) require that each alternating current generator arranged for parallel operation shall be provided with _____________. A. more than one means of excitation B. individual circuit fuses C. a high back-pressure trip D. a reverse-power trip

Last Answer : Answer: D

A generator is prevented from becoming motorized by the use of a/an _____________. A. overspeed trip B. reverse power relay C. back pressure trip D. governor controls

Description : A generator is prevented from becoming motorized by the use of a/an _____________. A. overspeed trip B. reverse power relay C. back pressure trip D. governor controls

Last Answer : Answer: B

Which power plant has minimum operating cost? a) Hydroelectric power plant b) Thermal power plant c) Nuclear power plant d) Gas Turbine Power Plant Ans: A 42. Which of the following have highest operating cost? a) Hydroelectric power plant b) Thermal power plant c) Nuclear power plant d) Solar electric power plant

Description : Which power plant has minimum operating cost? a) Hydroelectric power plant b) Thermal power plant c) Nuclear power plant d) Gas Turbine Power Plant Ans: A 42. Which of the following have ... a) Hydroelectric power plant b) Thermal power plant c) Nuclear power plant d) Solar electric power plant

Last Answer : Ans: B

The propeller shaft speed in a turbo-electric, synchronous, propulsion drive motor is changed by varying the __________. A. turbine speed B. number of motor poles C. field strength of the generator D. field strength of the motor

Description : The propeller shaft speed in a turbo-electric, synchronous, propulsion drive motor is changed by varying the __________. A. turbine speed B. number of motor poles C. field strength of the generator D. field strength of the motor

Last Answer : Answer: A

Turbine-Generator Lubrication Oil System Function

Description : Turbine-Generator Lubrication Oil System Function

Last Answer : Turbine-Generator Lubrication Oil System Function For large turbine-generators forced lubrication system and water cooling system should be continuously required during the operation of the turbine-generator and ... when the oil pressure is low. A second backup dc pumps are sometimes provided.

State the factors, for the choice of electrical system for an aero turbine.

Description : State the factors, for the choice of electrical system for an aero turbine.

Last Answer : A:The choice of electrical system for an aero turbine is guided by three factors: Type of electrical output: dc, variable- frequency ac, and constant- frequency ac. Aero turbine ... energy output: in conjunction with battery or other form of storage, or interconnection with power grid.

What are the working fluids in gas turbine?

Description : What are the working fluids in gas turbine?

Last Answer : 1.Air 2.Helium 3.Argon 4.Carbon dioxide

Explain reaction turbine in terms of head:

Description : Explain reaction turbine in terms of head:

Last Answer : High head- Francis Medium head- Propeller Low head- Kaplan

What is the purpose of TOPP (turbine oil purification plant)?

Description : What is the purpose of TOPP (turbine oil purification plant)? 

Last Answer : The purpose of TOPP is to remove the water ingress in turbine oil system from the gland leaks, cooler leakage, and solid metal particles, which are produced due to rust, wear of bearings and to normalize the ... capacity of TOPP is, for solids - 5 microns and for water - 300 to 500 parts per milli.

State turbine governor setting.

Description : State turbine governor setting. 

Last Answer : On 2560 rpm turbine governor becomes effective and on 2760 rpm is turbine governor take over speed. 

What is the type turbine installed in KGS?

Description : What is the type turbine installed in KGS? 

Last Answer : Tandem compounded to expansion of steam, impulse reaction type.  

What type of governing system used in turbine and what are the purposes of the system?

Description : What type of governing system used in turbine and what are the purposes of the system? 

Last Answer : Hydraulic governing system of centrifugal (speed) governer type is adopted in turbine. Sensitive oil pressure to actuate centrifugal governer is 6.1 kg/cm2 (max). At 6.7 kg/cm2 relief valve ... speeder gear from BPC signal. Once synchronised the grid frequency and speeder gear controls the speed. 

Write critical speeds of turbine generator?

Description : Write critical speeds of turbine generator?  

Last Answer : Generator rotor 1st critical speed 1283 rpm 2nd critical speed 3600 rpm Combined turbine generator 1st critical speed 1938 rpm 2nd critical speed 2120 rpm 3rd critical speed 2385 rpm 4th critical speed 2837 rpm 

What are the futures of turbine generator?

Description : What are the futures of turbine generator? 

Last Answer : a. Low heat drop b. Moisture control (HP-0.26%, LP-3%.) c. Turbine governing system d. 70% steam dumping to the condenser to avoid reactor trip. e. Gland sealing f. LP exhaust hood cooling g. Generator stator and rotor cooling h. Hydrogen sealing i. Static excitation 

How shaft voltage produced by turbine?

Description : How shaft voltage produced by turbine? 

Last Answer : Due to un-symmetry in the flux path of core, non-uniform air gap, un-symmetry in the rotor magnetic field during short circuit in the rotor winding, causes voltage to develop across the ends of rotor shaft. 

How turbine oil purification is achieved?

Description : How turbine oil purification is achieved?

Last Answer : Oil purification is achieved by centrifugal operation.  

Explain the main difference between impulse and reaction turbine.

Description : Explain the main difference between impulse and reaction turbine. 

Last Answer : When the inlet pressure of steam to the turbine is equal to outlet pressure of steam from the turbine the turbine is called the impulse turbine. In this type the heat is added is very less. ... than the inlet pressure of the steam. There is reduction in pressure with the increase in kinetic energy.

What is the purpose of turbine governing system?

Description : What is the purpose of turbine governing system?

Last Answer : Turbine governing system governs the speed of the turbine with the help of centrifugal governer. It reduces the steam inlet when turbine over speeds.  

What are the methods of removing moisture from turbine?

Description : What are the methods of removing moisture from turbine?

Last Answer : a. External method by moisture separator and reheater, which separates the moisture and reheates the steam. b. Internally by stainless steel mesh, which reduces moisture (water particles) to 1%. c. By main steam reheat. 

Explain the principle of working of impulse steam turbine.

Description : Explain the principle of working of impulse steam turbine. 

Last Answer : When steam enters the turbine it suffers a change in direction and momentum, which gives rise to the rotation of the turbine. There will be no drop in pressure in impulse steam turbine.  

State the factors, for the choice of electrical system for an aero turbine.

Description : State the factors, for the choice of electrical system for an aero turbine.

Last Answer : The choice of electrical system for an aero turbine is guided by three factors: Type of electrical output: dc, variablefrequency ac, and constant- frequency ac. Aero turbine rotational speed ... output: in conjunction with battery or other form of storage, or interconnection with power grid.

Flue gases coming out from furnace is first going through a) Turbine b) Economizer c) Air pre-heater d) Chimney

Description : Flue gases coming out from furnace is first going through a) Turbine b) Economizer c) Air pre-heater d) Chimney

Last Answer : Ans: Economizer

Water hamming effect is occurs in a) Surge tank b) Penstock c) Turbine d) Reservoir

Description : Water hamming effect is occurs in a) Surge tank b) Penstock c) Turbine d) Reservoir

Last Answer : Ans: Penstock

Low head plants generally use (A) Pelton Turbines (B) Francis Turbine (C) Pelton or Francis Turbine (D) Kaplan Turbines

Description : Low head plants generally use (A) Pelton Turbines (B) Francis Turbine (C) Pelton or Francis Turbine (D) Kaplan Turbines

Last Answer : Ans: A In the hysterisis motor, the direction of rotation can be reversed by shifting the shaded pole region with respect to main pole. But not by changing supply lead because it has ac supply.

Under normal conditions, storage batteries used for starting the emergency diesel generator are maintained in a charged state by which of the following methods? A. Trickle charging B. Fast charging C. Equalizing charge D. Reverse charging

Description : Under normal conditions, storage batteries used for starting the emergency diesel generator are maintained in a charged state by which of the following methods? A. Trickle charging B. Fast charging C. Equalizing charge D. Reverse charging

Last Answer : Answer: A

Equal power factors on paralleled AC generators are maintained by an automatic _____________. A. voltage regulator B. reverse power relay C. reverse current relay D. governor control switch

Description : Equal power factors on paralleled AC generators are maintained by an automatic _____________. A. voltage regulator B. reverse power relay C. reverse current relay D. governor control switch

Last Answer : Answer: A

A constant output voltage from an AC generator is maintained by the _____________. A. prime mover governor B. exciter generator C. voltage regulator D. reverse power relay

Description : A constant output voltage from an AC generator is maintained by the _____________. A. prime mover governor B. exciter generator C. voltage regulator D. reverse power relay

Last Answer : Answer: C

How coolant flow is maintained in the event of loss of power to the PHT system?

Description : How coolant flow is maintained in the event of loss of power to the PHT system?

Last Answer : When the PHT power fails, it takes two minutes for DG to come to full power. The circulation is maintained by flywheel, which increases the de-acceleration and maintains the flow for two minutes. If ... which more denser cold water comes down and less denser hot water goes up by convection method. 

How lub oil supply is maintained?

Description : How lub oil supply is maintained?  

Last Answer : Lubrication oil is supply is maintained by outlet oil from turbine oil pumps during normal operation and jacking oil pump during startup.

What is the value of vacuum maintained by vacuum pump in oil filteration machine?

Description : What is the value of vacuum maintained by vacuum pump in oil filteration machine?

Last Answer : 27 Hg.

Component F in the illustrated device is for _________. EL-0033 A. short circut protection B. latching the trip unit closed after resetting the breaker C. overload protection D. providing a flexible connection between the input terminal G and the tripping unit E

Description : Component F in the illustrated device is for _________. EL-0033 A. short circut protection B. latching the trip unit closed after resetting the breaker C. overload protection D. providing a flexible connection between the input terminal G and the tripping unit E

Last Answer : Answer: C

How will a molded-case circuit breaker react after it has tripped, as a result of an overloaded circuit? A. The breaker will trip again if immediately reset. B. The breaker handle will lock in the OFF position. C. The breaker handle will lock in the tripped position until the thermal element cools down. D. The breaker handle cannot be moved to the OFF position until the thermal element cools down.

Description : How will a molded-case circuit breaker react after it has tripped, as a result of an overloaded circuit? A. The breaker will trip again if immediately reset. B. The breaker handle will lock in ... down. D. The breaker handle cannot be moved to the OFF position until the thermal element cools down.

Last Answer : Answer: A

When power is restored after a complete power failure, a steering gear pump motor will ____________. A. have to be restarted B. have to be reset C. restart automatically D. trip its overload relays

Description : When power is restored after a complete power failure, a steering gear pump motor will ____________. A. have to be restarted B. have to be reset C. restart automatically D. trip its overload relays

Last Answer : Answer: C

Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation (B) Cavitation may be caused due to boiling of liquid by decreasing the pressure resulting in formation & collapse of vapor cavities (C) Cavitation begins at higher static pressure and lower velocity in larger diameter pipelines resulting in audible noise(D) Large scale cavitation cannot damage pipeline, restrict fluid flow anddamage steam turbine blades

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Hydraulic __________ works on the principle of Pascal's law of transmission of fluid pressure. (A) Press (B) Turbine (C) Pump (D) Coupling

Description : Hydraulic __________ works on the principle of Pascal's law of transmission of fluid pressure. (A) Press (B) Turbine (C) Pump (D) Coupling

Last Answer : (A) Press

6. Liquefaction of gases cannot be done by (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Merely compressing it beyond critical pressure (D) Adiabatic expansion against a piston or in a turbine

Description : 6. Liquefaction of gases cannot be done by (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Merely compressing it beyond critical pressure (D) Adiabatic expansion against a piston or in a turbine

Last Answer : (C) Merely compressing it beyond critical pressure

Claude process of gas liquefaction employs (A) Merely compression of gas beyond its critical pressure (B) Joule-Thomson expansion cooling (C) Heat exchange with colder stream (D) Adiabatic expansion against a piston or in a turbine

Description : Claude process of gas liquefaction employs (A) Merely compression of gas beyond its critical pressure (B) Joule-Thomson expansion cooling (C) Heat exchange with colder stream (D) Adiabatic expansion against a piston or in a turbine

Last Answer : (D) Adiabatic expansion against a piston or in a turbine

Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Description : Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Last Answer : (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion)

In a Rankine cycle, with the maximum steam temperature being fixed from metallurgical considerations, as the boiler pressure increases (a) The condenser load will increase [IES-1997] (b) The quality of turbine exhaust will decrease (c) The quality of turbine exhaust will increase (d) The quality of turbine exhaust will remain unchanged

Description : In a Rankine cycle, with the maximum steam temperature being fixed from metallurgical considerations, as the boiler pressure increases (a) The condenser load will increase [IES-1997] (b) The ... The quality of turbine exhaust will increase (d) The quality of turbine exhaust will remain unchanged

Last Answer : (b) The quality of turbine exhaust will decrease 

In a Rankine cycle, regeneration results in higher efficiency because (a) Pressure inside the boiler increases [GATE-2003] (b) Heat is added before steam enters the low pressure turbine (c) Average temperature of heat addition in the boiler increases (d) Total work delivered by the turbine increases

Description : In a Rankine cycle, regeneration results in higher efficiency because (a) Pressure inside the boiler increases [GATE-2003] (b) Heat is added before steam enters the low pressure turbine (c) ... temperature of heat addition in the boiler increases (d) Total work delivered by the turbine increases 

Last Answer : (c) Average temperature of heat addition in the boiler increases  

High pressure steam is expanded adiabatically and reversibly through a well insulated turbine, which produces some shaft work. If the enthalpy change and entropy change across the turbine are represented by ΔH and ΔS respectively for this process: (A) Δ H = 0 and ΔS = 0 (B) Δ H ≠ 0 and ΔS = 0 (C) Δ H ≠ 0 and ΔS ≠ 0 (D) Δ H = 0 and ΔS ≠ 0

Description : High pressure steam is expanded adiabatically and reversibly through a well insulated turbine, which produces some shaft work. If the enthalpy change and entropy change across the turbine are represented by ΔH and ΔS respectively for this process: ... (C) Δ H ≠ 0 and ΔS ≠ 0 (D) Δ H = 0 and ΔS ≠ 0

Last Answer : (B) Δ H ≠ 0 and ΔS = 0