Write critical speeds of turbine generator?

Write critical speeds of turbine generator?  
by

1 Answer

Answer :

Generator rotor
1st critical speed 1283 rpm
2nd critical speed 3600 rpm
Combined turbine generator
1st critical speed 1938 rpm
2nd critical speed 2120 rpm
3rd critical speed 2385 rpm
4th critical speed 2837 rpm 
by

Related questions

In a diesel electric plant, raising the generator's field excitation will cause the DC propulsion motor to ________. A. increase in speed B. decrease in speed C. affect generator speed only D. affect main motor speed if done in conjunction with higher generator engine speeds

Description : In a diesel electric plant, raising the generator's field excitation will cause the DC propulsion motor to ________. A. increase in speed B. decrease in speed C. affect generator speed only D. affect main motor speed if done in conjunction with higher generator engine speeds

Last Answer : Answer: A

On some diesel-electric ships, the DC propulsion motor will only attain half speed when the generator fields are fully excited. Speeds above this are obtained by _____________. A. rotating brush alignment B. raising the generator engine speed C. lowering the generator engine speed D. decreasing excitation

Description : On some diesel-electric ships, the DC propulsion motor will only attain half speed when the generator fields are fully excited. Speeds above this are obtained by _____________. A. rotating brush ... B. raising the generator engine speed C. lowering the generator engine speed D. decreasing excitation

Last Answer : Answer: B

The propeller shaft speed in a turbo-electric, synchronous, propulsion drive motor is changed by varying the __________. A. turbine speed B. number of motor poles C. field strength of the generator D. field strength of the motor

Description : The propeller shaft speed in a turbo-electric, synchronous, propulsion drive motor is changed by varying the __________. A. turbine speed B. number of motor poles C. field strength of the generator D. field strength of the motor

Last Answer : Answer: A

Turbine-Generator Lubrication Oil System Function

Description : Turbine-Generator Lubrication Oil System Function

Last Answer : Turbine-Generator Lubrication Oil System Function For large turbine-generators forced lubrication system and water cooling system should be continuously required during the operation of the turbine-generator and ... when the oil pressure is low. A second backup dc pumps are sometimes provided.

What are the futures of turbine generator?

Description : What are the futures of turbine generator? 

Last Answer : a. Low heat drop b. Moisture control (HP-0.26%, LP-3%.) c. Turbine governing system d. 70% steam dumping to the condenser to avoid reactor trip. e. Gland sealing f. LP exhaust hood cooling g. Generator stator and rotor cooling h. Hydrogen sealing i. Static excitation 

In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD winding through the voltage regulator. C. the controller to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Description : In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD ... to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Last Answer : Answer: B

Which of the following conditions does not hold good for a solution to a critical section problem ? (A) No assumptions may be made about speeds or the number of CPUs. (B) No two processes may be simultaneously inside their critical sections. (C) Processes running outside its critical section may block other processes. (D) Processes do not wait forever to enter its critical section.

Description : Which of the following conditions does not hold good for a solution to a critical section problem ? (A) No assumptions may be made about speeds or the number of CPUs. (B) No two processes ... critical section may block other processes. (D) Processes do not wait forever to enter its critical section.

Last Answer : (C) Processes running outside its critical section may block other processes. 

6. Liquefaction of gases cannot be done by (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Merely compressing it beyond critical pressure (D) Adiabatic expansion against a piston or in a turbine

Description : 6. Liquefaction of gases cannot be done by (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Merely compressing it beyond critical pressure (D) Adiabatic expansion against a piston or in a turbine

Last Answer : (C) Merely compressing it beyond critical pressure

Claude process of gas liquefaction employs (A) Merely compression of gas beyond its critical pressure (B) Joule-Thomson expansion cooling (C) Heat exchange with colder stream (D) Adiabatic expansion against a piston or in a turbine

Description : Claude process of gas liquefaction employs (A) Merely compression of gas beyond its critical pressure (B) Joule-Thomson expansion cooling (C) Heat exchange with colder stream (D) Adiabatic expansion against a piston or in a turbine

Last Answer : (D) Adiabatic expansion against a piston or in a turbine

Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Description : Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Last Answer : (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion)

How can I run a gas turbine power generator efficiently?

Description : How can I run a gas turbine power generator efficiently?

Last Answer : www.muellerenvironmental.com/documents/GER3567H.pdf discusses many factors affecting gas turbine efficiency. It specifically addresses GE turbines, but the factors discussed are relevant to all gas turbine power generators.

Once the condensate reaches the _____ , it becomes available to the boiler for recycling. • Condenser • Turbine • Boiler • Generator

Description : Once the condensate reaches the _____ , it becomes available to the boiler for recycling. • Condenser • Turbine • Boiler • Generator

Last Answer : • Boiler

Consider efficiencies of hydro-turbines and generators. If the efficiency of a hydro-turbine is 80% and the efficiency of a generator is 90%, what is the overall efficiency of the unit? w) 85% x) 72% y) 90% z) 70%

Description : Consider efficiencies of hydro-turbines and generators. If the efficiency of a hydro-turbine is 80% and the efficiency of a generator is 90%, what is the overall efficiency of the unit? w) 85% x) 72% y) 90% z) 70% 

Last Answer : ANSWER: X -- 72%

Why is a shaft coupler used between turbine and generator ?

Description : Why is a shaft coupler used between turbine and generator ?

Last Answer : For easy transmission torque or rotation angle and can also use for the protection of the safety devices shaft cannot be separated from the shaft during motion coupling will be damaged first so as avoid to the damaged of motor or other transmission parts.

A hydraulic turbine having rated speed of 250 rpm is connected to a synchronous generator. In order to

Description : A hydraulic turbine having rated speed of 250 rpm is connected to a synchronous generator. In order to produce power at 50 Hz, the number of poles required in the generator are (A) 6 (B) 12 (C) 16 (D) 24

Last Answer : A hydraulic turbine having rated speed of 250 rpm is connected to a synchronous generator. In order to produce power at 50 Hz, the number of poles required in the generator are 24

Which of the following statements is true concerning the motor controller diagram shown in the illustration? EL-0023 A. Terminal 'T2' is hot only on high speed. B. Both indicating lights will be lit on both high and low speeds as they are connected to the common lead when the motor is running. C. Overload protection is provided for high speed operation only. D. 'L2' is always connected to 'T2' whenever the motor is running.

Description : Which of the following statements is true concerning the motor controller diagram shown in the illustration? EL-0023 A. Terminal 'T2' is hot only on high speed. B. Both indicating lights will be lit on ... high speed operation only. D. 'L2' is always connected to 'T2' whenever the motor is running.

Last Answer : Answer: D

The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to obtain required speeds B. divert shunt field current for speed control in both directions of operation C. limit armature current in hoist and 'series field' current in lower to obtain required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation

Description : The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to ... required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation

Last Answer : Answer: C

Kilowatt load is divided between two AC generators operating in parallel by _____________. A. adjusting the governor controls B. varying the excitation voltage C. increasing both prime mover speeds simultaneously D. decreasing both prime mover speeds simultaneously

Description : Kilowatt load is divided between two AC generators operating in parallel by _____________. A. adjusting the governor controls B. varying the excitation voltage C. increasing both prime mover speeds simultaneously D. decreasing both prime mover speeds simultaneously

Last Answer : Answer: A

Electric propulsion coupling excitation is reduced at slow speeds to ___________. A. increase speed control B. increase shaft torque C. prevent coupling overheating D. prevent coupling slippage

Description : Electric propulsion coupling excitation is reduced at slow speeds to ___________. A. increase speed control B. increase shaft torque C. prevent coupling overheating D. prevent coupling slippage

Last Answer : Answer: C

Which power plant has minimum operating cost? a) Hydroelectric power plant b) Thermal power plant c) Nuclear power plant d) Gas Turbine Power Plant Ans: A 42. Which of the following have highest operating cost? a) Hydroelectric power plant b) Thermal power plant c) Nuclear power plant d) Solar electric power plant

Description : Which power plant has minimum operating cost? a) Hydroelectric power plant b) Thermal power plant c) Nuclear power plant d) Gas Turbine Power Plant Ans: A 42. Which of the following have ... a) Hydroelectric power plant b) Thermal power plant c) Nuclear power plant d) Solar electric power plant

Last Answer : Ans: B

State the factors, for the choice of electrical system for an aero turbine.

Description : State the factors, for the choice of electrical system for an aero turbine.

Last Answer : A:The choice of electrical system for an aero turbine is guided by three factors: Type of electrical output: dc, variable- frequency ac, and constant- frequency ac. Aero turbine ... energy output: in conjunction with battery or other form of storage, or interconnection with power grid.

What are the working fluids in gas turbine?

Description : What are the working fluids in gas turbine?

Last Answer : 1.Air 2.Helium 3.Argon 4.Carbon dioxide

Explain reaction turbine in terms of head:

Description : Explain reaction turbine in terms of head:

Last Answer : High head- Francis Medium head- Propeller Low head- Kaplan

What is the purpose of TOPP (turbine oil purification plant)?

Description : What is the purpose of TOPP (turbine oil purification plant)? 

Last Answer : The purpose of TOPP is to remove the water ingress in turbine oil system from the gland leaks, cooler leakage, and solid metal particles, which are produced due to rust, wear of bearings and to normalize the ... capacity of TOPP is, for solids - 5 microns and for water - 300 to 500 parts per milli.

State turbine governor setting.

Description : State turbine governor setting. 

Last Answer : On 2560 rpm turbine governor becomes effective and on 2760 rpm is turbine governor take over speed. 

What is the type turbine installed in KGS?

Description : What is the type turbine installed in KGS? 

Last Answer : Tandem compounded to expansion of steam, impulse reaction type.  

What type of governing system used in turbine and what are the purposes of the system?

Description : What type of governing system used in turbine and what are the purposes of the system? 

Last Answer : Hydraulic governing system of centrifugal (speed) governer type is adopted in turbine. Sensitive oil pressure to actuate centrifugal governer is 6.1 kg/cm2 (max). At 6.7 kg/cm2 relief valve ... speeder gear from BPC signal. Once synchronised the grid frequency and speeder gear controls the speed. 

How shaft voltage produced by turbine?

Description : How shaft voltage produced by turbine? 

Last Answer : Due to un-symmetry in the flux path of core, non-uniform air gap, un-symmetry in the rotor magnetic field during short circuit in the rotor winding, causes voltage to develop across the ends of rotor shaft. 

How dearator pressure is maintained after turbine trip?

Description : How dearator pressure is maintained after turbine trip? 

Last Answer : Pegging steam is used to maintain dearator pressure after turbine trip.  

How turbine oil purification is achieved?

Description : How turbine oil purification is achieved?

Last Answer : Oil purification is achieved by centrifugal operation.  

Explain the main difference between impulse and reaction turbine.

Description : Explain the main difference between impulse and reaction turbine. 

Last Answer : When the inlet pressure of steam to the turbine is equal to outlet pressure of steam from the turbine the turbine is called the impulse turbine. In this type the heat is added is very less. ... than the inlet pressure of the steam. There is reduction in pressure with the increase in kinetic energy.

What is the purpose of turbine governing system?

Description : What is the purpose of turbine governing system?

Last Answer : Turbine governing system governs the speed of the turbine with the help of centrifugal governer. It reduces the steam inlet when turbine over speeds.  

What are the methods of removing moisture from turbine?

Description : What are the methods of removing moisture from turbine?

Last Answer : a. External method by moisture separator and reheater, which separates the moisture and reheates the steam. b. Internally by stainless steel mesh, which reduces moisture (water particles) to 1%. c. By main steam reheat. 

Explain the principle of working of impulse steam turbine.

Description : Explain the principle of working of impulse steam turbine. 

Last Answer : When steam enters the turbine it suffers a change in direction and momentum, which gives rise to the rotation of the turbine. There will be no drop in pressure in impulse steam turbine.  

State the factors, for the choice of electrical system for an aero turbine.

Description : State the factors, for the choice of electrical system for an aero turbine.

Last Answer : The choice of electrical system for an aero turbine is guided by three factors: Type of electrical output: dc, variablefrequency ac, and constant- frequency ac. Aero turbine rotational speed ... output: in conjunction with battery or other form of storage, or interconnection with power grid.

Flue gases coming out from furnace is first going through a) Turbine b) Economizer c) Air pre-heater d) Chimney

Description : Flue gases coming out from furnace is first going through a) Turbine b) Economizer c) Air pre-heater d) Chimney

Last Answer : Ans: Economizer

Water hamming effect is occurs in a) Surge tank b) Penstock c) Turbine d) Reservoir

Description : Water hamming effect is occurs in a) Surge tank b) Penstock c) Turbine d) Reservoir

Last Answer : Ans: Penstock

Low head plants generally use (A) Pelton Turbines (B) Francis Turbine (C) Pelton or Francis Turbine (D) Kaplan Turbines

Description : Low head plants generally use (A) Pelton Turbines (B) Francis Turbine (C) Pelton or Francis Turbine (D) Kaplan Turbines

Last Answer : Ans: A In the hysterisis motor, the direction of rotation can be reversed by shifting the shaded pole region with respect to main pole. But not by changing supply lead because it has ac supply.

Write nameplate details of the main generator.

Description : Write nameplate details of the main generator. 

Last Answer : Type THW-235 kW 237700 kVA 264000 Voltage 16500 V Amps 9240 A Power factor 0.9 lag. Field voltage 326 V Field current 2755 A Insulation Class-F Speed 3000 rpm 50 Hz, 3, double star connection. 

A ultra-supercritical steam generator operates at pressures above the critical pressure- a. 2400 psi b. 1500 psi c. 3200 psi d. 4600 psi

Description : A ultra-supercritical steam generator operates at pressures above the critical pressure- a. 2400 psi b. 1500 psi c. 3200 psi d. 4600 psi

Last Answer : c. 3200 psi

Which type of generator is a type of boiler that at maximum critical pressure frequently used in the production of electric power. a. Supercritical boiler b. High pressure boiler c. Low pressure boiler d. None

Description : Which type of generator is a type of boiler that at maximum critical pressure frequently used in the production of electric power. a. Supercritical boiler b. High pressure boiler c. Low pressure boiler d. None

Last Answer : a. Supercritical boiler

If the field circuit resistance of a d.c. generator exceed its critical value, then the generator : -

Description :  If the field circuit resistance of a d.c. generator exceed its critical value, then the generator : -  a) fails to build up b) builds up a very high voltage c) exceeds its current capacity d) produces power beyond its rating 

Last Answer :  If the field circuit resistance of a d.c. generator exceed its critical value, then the generator : - fails to build up 

The critical resistance of the D.C. generator is the resistance of?

Last Answer : The critical resistance of the D.C. generator is the resistance of field.

In a D.C. generator the critical resistance refers to the resistance of?

Last Answer : In a D.C. generator, the critical resistance refers to the resistance of field.

Write names of parts of wind turbine.

Description : Write names of parts of wind turbine.

Last Answer : Tower Blades Hub Rotor Shaft Gearbox Generator Controller Brake Anemometer Nacelle Yaw drive mechanism etc

Critical pressure of water is (A) 1 kg / cm2 (B) 100 kg / cm2 (C) 155 kg / cm2 (D) 213.8 kg / cm2 .

Description : Critical pressure of water is (A) 1 kg / cm2 (B) 100 kg / cm2 (C) 155 kg / cm2 (D) 213.8 kg / cm2 .

Last Answer : Ans: D

Which of the following characteristics is most critical in determining the size of the cable to be used in a particular circuit? A. voltage rating B. weight per unit length C. current rating D. inductance per unit length

Description : Which of the following characteristics is most critical in determining the size of the cable to be used in a particular circuit? A. voltage rating B. weight per unit length C. current rating D. inductance per unit length

Last Answer : Answer: C

Define critical clearing time and critiacal clearing angle

Description : Define critical clearing time and critiacal clearing angle

Last Answer : The critical clearing angle is the max. allowable change in the power angle before clearing the fault, without loss of synchronism. The critical clearing time can be defined as thw max. time delay that can be allowed to clear a fault without loss of synchronism.