Gas Insulated Substations Advantages Disadvantages

Gas Insulated Substations Advantages Disadvantages
by

1 Answer

Answer :

Gas Insulated Substations (GIS):
Gas Insulated Substations (GIS) are differ from Air Insulated Substations (substations we usually see) such that all the substation equipment such as busbars, circuit breakers, current transformer, potential transformers and other substation equipment are placed inside SF6 modules filled with SF6 gas. SF6 gas which has high dielectric property acts as insulating medium to the High Voltage or Extra High Voltage substation equipment. Generally Gas Insulted Substations (GIS) are indoor type as it requires 1/10th of the space required for conventional substations. Some of the advantages and disadvantages of Gas Insulated Substations (GIS) are:
Advantages of GIS Substation:
It occupies very less space (1/10th) compared to ordinary substations. Hence these Gas Insulated Substations (GIS) are most preferred where area for substation is small (eg: Cities)
Most reliable compared to Air Insulated Substations, number of outages due to the fault is less
Maintenance Free
Can be assembled at the shop and modules can be commissioned in the plant easily


Disadvantages of GIS Substation:
Cost is higher compared to Ordinary Conventional Substations
Care should be taken that no dust particles enter into the live compartments which results in flash overs
When fault occurs internally,diagnosis of the fault and rectifying this takes very long time (outage time is high)
SF6 gas pressure must be monitored in each compartment, reduction in the pressure of the SF6 gas in any module results in flash overs and faults
by

Related questions

What are different types of busbar arrangement Schemes in Substations?

Description : What are different types of busbar arrangement Schemes in Substations?

Last Answer : Different switching schemes or busbar arrangement scheme employed in switch-yard are: Single Bus Scheme Double bus single breaker scheme Main and Transfer busbar scheme Double bus single breaker scheme Breaker and half scheme Ring main bus scheme

What is the significance of Corona rings in substations?

Description : What is the significance of Corona rings in substations?

Last Answer : It is observed that corona discharge occurs mostly at sharp corners, edges near the conductor fixing points. Corona rings also called grading rings are hallow metallic rings having large diameter ... is reduced to much lower value Corona discharge is eliminated Dust deposition is also minimized

What are different insulators employed in substations?

Description : What are different insulators employed in substations?

Last Answer : Some of the insulators employed in substations are: Pin insulators Post insulators Strain insulators Suspension insulators Hallow apparatus insulators Dead-end insulators Solid core insulators

What are the advantages of PVC insulated cable?

Description : What are the advantages of PVC insulated cable? 

Last Answer : a. Plumbing is not required. Joints can be made easily. b. As PVC is light the injury caused to it while laying is less. c. It is corrosion resistant. d. It has high fire retarding property. e. It does not break down even if moisture enters. 

Locations where Gas Insulated Substation is preferred

Description : Locations where Gas Insulated Substation is preferred

Last Answer : Gas Insulated Substations are preferred in the places where land requirement for the substation is difficult such as in populated areas and highly polluted areas where outdoor switchyard is not ... pollution and saline environment. Under such case indoor GIS substation is very much helpful.

For cost and safety, the outdoor substations are installed for voltages above (a) 11 kV (b) 33 kV (c) 60kV (d) 110kV

Description : For cost and safety, the outdoor substations are installed for voltages above (a) 11 kV (b) 33 kV (c) 60kV (d) 110kV

Last Answer : (b) 33 kV

Substations.....

Description : Distributed under Creative Commons Attribution-ShareAlike - CC BY-SA.

Last Answer : Substations  Substations are the places where the level of voltage undergoes change with the help of transformers. Apart from transformers a substation will house switches (called circuit breakers), meters, relays ... 6 kV/400 V distribution transformer.  Version 2 EE IIT, Kharagpur 

For cost and safety, the outdoor substations are installed for voltages above?

Last Answer : For cost and safety, the outdoor substations are installed for voltages above 33 kV.

On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. millivolt meter and a jumper B. ohmmeter C. megohm meter D. high potential tester

Description : On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. millivolt meter and a jumper B. ohmmeter C. megohm meter D. high potential tester

Last Answer : Answer: A

On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. ohmmeter with the machine secured B. millivolt meter and a jumper with the machine running C. megohm meter with the machine running D. voltmeter and ampmeter with the machine running

Description : On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. ohmmeter with the ... C. megohm meter with the machine running D. voltmeter and ampmeter with the machine running

Last Answer : Answer: B

One of the generator bearing shells is generally insulated from the end housing in order to prevent _____________. A. rapid brush wear B. residual magnetism leak off C. excessive field winding heat D. circulation of shaft currents

Description : One of the generator bearing shells is generally insulated from the end housing in order to prevent _____________. A. rapid brush wear B. residual magnetism leak off C. excessive field winding heat D. circulation of shaft currents

Last Answer : Answer: D

One of the generator or motor bearings is generally insulated from the end housing in order to prevent ________. A. rapid brush wear B. current leakage from the shaft C. excessive field winding heat D. circulation of shaft currents induced in the machine's frame

Description : One of the generator or motor bearings is generally insulated from the end housing in order to prevent ________. A. rapid brush wear B. current leakage from the shaft C. excessive field winding heat D. circulation of shaft currents induced in the machine's frame

Last Answer : Answer: D

When changing fuses and the spring clips are found to have lost their grip, they should be replaced or _____________. A. tightened firmly with insulated pliers B. clip clamps should be used C. wired closed with uninsulated, varnished copper wire D. carefully bent back to their original shapes

Description : When changing fuses and the spring clips are found to have lost their grip, they should be replaced or _____________. A. tightened firmly with insulated pliers B. clip clamps should be used C. wired closed with uninsulated, varnished copper wire D. carefully bent back to their original shapes

Last Answer : Answer: B

When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Description : When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Last Answer : Answer: C

When a transformer is used to step down voltage, the low voltage winding is _____________. A. part of the core B. the primary coil C. not insulated D. the secondary coil

Description : When a transformer is used to step down voltage, the low voltage winding is _____________. A. part of the core B. the primary coil C. not insulated D. the secondary coil

Last Answer : Answer: D

Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it with a de-energized tag C. be equipped with an insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Description : Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should ____________. A. gently tap the body with a screwdriver B. tag it ... insulated fuse puller D. short circuit the terminals to make sure that the capacitor is discharged

Last Answer : Answer: D

In an impressed current cathodic protection system, the anode is ____________. A. connected to the hull and deteriorates with time B. insulated from the hull and does not waste away C. connected to the hull but does not waste away D. insulated from the hull but deteriorates with time

Description : In an impressed current cathodic protection system, the anode is ____________. A. connected to the hull and deteriorates with time B. insulated from the hull and does not waste away C. connected to the hull but does not waste away D. insulated from the hull but deteriorates with time

Last Answer : Answer: B

A 'dead front' switchboard is one _____________. A. without switches on it B. with insulated switches and no exposed terminals C. without circuit breakers D. without safety hand rails nor rubber mats

Description : A 'dead front' switchboard is one _____________. A. without switches on it B. with insulated switches and no exposed terminals C. without circuit breakers D. without safety hand rails nor rubber mats

Last Answer : Answer: B

A tubular fuse should always be removed from a fuse panel with _____________. A. a screwdriver B. a pair of insulated metal pliers C. any insulated object D. fuse pullers

Description : A tubular fuse should always be removed from a fuse panel with _____________. A. a screwdriver B. a pair of insulated metal pliers C. any insulated object D. fuse pullers

Last Answer : Answer: D

To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws of the instrument around the insulated conductor C. connect the voltage test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Description : To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws ... test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Last Answer : Answer: B

Define insulated wire.

Description : Define insulated wire. 

Last Answer : Insulated wire: A conductor or multi-stranded conductor which has a insulating material on it is called a insulated wire. 

Define unprotected insulated wire.

Description : Define unprotected insulated wire. 

Last Answer : Unprotected insulated wire: Unprotected insulated wire is which the insulation of the wire is not covered by a protective sheathing to prevent it from mechanical damage. 

What are the parts of paper insulated lead covered cable?

Description : What are the parts of paper insulated lead covered cable?

Last Answer : a. Core. b. Insulation of cable. c. Metallic sheath. d. Bedding. e. Armouring. f. Serving.

For LV applications (below 1 kV), ______________ cables are used. (A) Paper insulated. (B) Plastic. (C) Single core cables. (D) Oil filled.

Description : For LV applications (below 1 kV), ______________ cables are used. (A) Paper insulated. (B) Plastic. (C) Single core cables. (D) Oil filled.

Last Answer : Ans: C For low voltage applications single core cables are suitable.

Slip ring induction motor advantages and disadvantages compared to squirrel cage motors?

Description : Slip ring induction motor advantages and disadvantages compared to squirrel cage motors?

Last Answer : Advantages: High starting torque with low starting current Smooth acceleration under heavy loads No abnormal heating during starting Good running characteristics after external rotor resistances are cut out ... cage motors The speed regulation is poor when run with resistance in the rotor circuit

What are the advantages and disadvantages of Induction Motors?

Description : What are the advantages and disadvantages of Induction Motors?

Last Answer : Advantages: It is simple and rugged in construction It is relatively cheap Induction motors require less maintenance Induction motor has high efficiency and reasonably good power factor 3-phase induction ... and its speed cannot be changed easily Its starting torque is inferior to dc shunt motor

Air Blast Circuit Breakers Advantages Disadvantages

Description : Air Blast Circuit Breakers Advantages Disadvantages

Last Answer : Air Blast Circuit Breakers Advantages Disadvantages In air blast circuit breakers, compressed air at a pressure of 20-30 kg/cm2 is employed as an arc quenching medium. Air blast circuit breakers ... air blast circuit breaker current chopping problem exists There is a problem of re-striking voltage

Closed loop and Open loop Control System Advantages and Disadvantages

Description : Closed loop and Open loop Control System Advantages and Disadvantages

Last Answer : Open Loop Control System: Control System in which output quantity has no effect on the input quantity is called Open Loop Control System. Open Loop Control System has no facility to correct automatically the ... in the closed loop system and more care is needed to design a stable closed loop system

What Are The Advantages And Disadvantages Of Short-pitched Winding?

Description : What Are The Advantages And Disadvantages Of Short-pitched Winding?

Last Answer : The advantages are: They save copper for end connections They improve the waveform of the generated EMF. The generated EMF can be made to approximate to a sine wave more easily and the distorting ... some what reduced. Because the voltage induced in the two coil sides are slightly out of phase.

What Are The Advantages And Disadvantages Of Ac, Dc Motors?

Description : What Are The Advantages And Disadvantages Of Ac, Dc Motors?

Last Answer : Advantages of AC Motors: Low cost, long life, high efficiency, large ratings available (to 1 MW or more), large number of standardized types. Disadvantages of AC Motors: Starting inrush current ... DC Motors: Some can be costly, Require a controller, Higher initial cost, Requires a controller.

What are the advantages and disadvantages of three dark lamps method of synchronizing?

Description : What are the advantages and disadvantages of three dark lamps method of synchronizing?

Last Answer : Advantages: · The synchronous switch using lamps is inexpensive · Checking for correctness of the phase sequence can be obtained in a simple manner which is essential especially when the Alternator ... The frequency of the incoming Alternator in relation to the bus-bar frequency is not available.

What are the advantages and disadvantages of estimating the voltage regulation of an Alternator by EMF method?

Description : What are the advantages and disadvantages of estimating the voltage regulation of an Alternator by EMF method?

Last Answer : Advantages: · Simple no load tests (for obtaining OCC and SCC) are to be conducted · Calculation procedure is much simpler Disadvantages: · The value of voltage regulation obtained by this method is always higher than the actual value

What are the advantages and disadvantages of large air gap length in induction motor?

Description : What are the advantages and disadvantages of large air gap length in induction motor?

Last Answer : Advantage: A large air gap length results in higher overload capacity, better cooling, reduction in noise and reduction in unbalanced magnetic pull. Disadvantages: The disadvantage of large air gap length is that it results in high value of magnetizing current.

What are the advantages and disadvantages of direct load test for 3 – phase I M?

Description : What are the advantages and disadvantages of direct load test for 3 – phase I M?

Last Answer : Advantages Direct measurement of input and output parameters yield accurate results Aside from the usual performance other performances like mechanical vibration, noise etc can be studied. By ... energy delivered is wasted Loading arrangement cannot be provided for motors of large power rating

What are the advantages and disadvantages of circle diagram method of predetermining the performance of 3 – phase I M?

Description : What are the advantages and disadvantages of circle diagram method of predetermining the performance of 3 – phase I M?

Last Answer : The prediction can be carried out when any of the following information is available The input line current., the input power factor, The active power input, The reactive power input, The ... is, being a geometrical solution, errors made during measurements will affect the accuracy of the result.

What are the advantages and disadvantages of planned maintenance?

Description : What are the advantages and disadvantages of planned maintenance?

Last Answer :  Advantages of Planned Maintenance. 1. As the name reflects maintenance jobs planned properly ie. manpower, tools, tackles, required for maintenance is well planned and readily available or reserved for ... 4. In NPP we cannot accept unplanned jobs, as all works are safety related/important. 

What are the advantages and disadvantages of 415V English Electric breaker?

Description : What are the advantages and disadvantages of 415V English Electric breaker? 

Last Answer : Advantages 1. Auto reclosing shutters. 2. Proven wiping contacts. 3. Sturdy rugged mechanism. 4. Reliable aux. Switches contacts. 5. Slow closing facility independent of closing spring. ... also. No neutral bus bar link, we cannot finger contact resistance since fixed on bus side. 

Pick out the correct statement. (A) If an insoluble gas is passed through a volatile liquid placed in a perfectly insulated container, the temperature of the liquid will increase (B) A process is irreversible as long as Δ S for the system is greater than zero (C) The mechanical work done by a system is always equal to∫P.dV (D) The heat of formation of a compound is defined as the heat of reaction leading to the formation of the compound from its reactants

Description : Pick out the correct statement. (A) If an insoluble gas is passed through a volatile liquid placed in a perfectly insulated container, the temperature of the liquid will increase (B) A ... compound is defined as the heat of reaction leading to the formation of the compound from its reactants

Last Answer : (D) The heat of formation of a compound is defined as the heat of reaction leading to the formation of the compound from its reactants

1m3 of an ideal gas at 500 K and 1000 kPa expands reversibly to 5 times its initial volume in an insulated container. If the specific heat capacity (at constant pressure) of the gas is 21 J/mole . K, the final temperature will be (A) 35 K (B) 174 K (C) 274 K (D) 154 K

Description : 1m3 of an ideal gas at 500 K and 1000 kPa expands reversibly to 5 times its initial volume in an insulated container. If the specific heat capacity (at constant pressure) of the gas is 21 J/mole . K, the final temperature will be (A) 35 K (B) 174 K (C) 274 K (D) 154 K

Last Answer : (C) 274 K

An ideal gas is compressed in a cylinder so well insulated that there is essentially no heat transfer. The temperature of gas  a. Remains constant  b. increases  c. decreases  d. is basically zero

Description : An ideal gas is compressed in a cylinder so well insulated that there is essentially no heat transfer. The temperature of gas  a. Remains constant  b. increases  c. decreases  d. is basically zero

Last Answer : increases

Cables for 220 kV lines are invariably (a) mica insulated (b) paper insulated (c) compressed oil or compressed gas insulated (d) rubber insulated (e) none of the above

Description : Cables for 220 kV lines are invariably (a) mica insulated (b) paper insulated (c) compressed oil or compressed gas insulated (d) rubber insulated (e) none of the above

Last Answer : (c) compressed oil or compressed gas insulated

What are the advantages and disadvantages of electric burners as oppose to gas burners?

Description : What are the advantages and disadvantages of electric burners as oppose to gas burners?

Last Answer : Electric burners have the advantages of reducing fire hazard due to the lack of open flame, not needing to have a gas line to run the burner, and eliminating the risk of a gas leak from the ... setting changes, and the risk of burn since the burner surface stays hot relatively longer after shut-off.

What are the advantages and disadvantages of gas cook tops versus electric?

Description : What are the advantages and disadvantages of gas cook tops versus electric?

Last Answer : Gas stoves heat up or cool down faster when you change the temperature, whereas electric induction stoves can boil water in less than a minute. Gas stoves can be dangerous if there is a gas leak, while electric stoves can be dangerous because there is no actual flame to see.

Does anyone know where I can find an insulated coffee mug that is not made for a cup holder?

Description : Does anyone know where I can find an insulated coffee mug that is not made for a cup holder?

Last Answer : Amazon has a few. There are a lot of those tall narrow ones, but I saw a few more “portly” mugs.

How low can the temperature go in an unheated but insulated cabin in order to damage LCD TV, phone, and computer?

Description : How low can the temperature go in an unheated but insulated cabin in order to damage LCD TV, phone, and computer?

Last Answer : answer:Are you the only one closing in on ten thousand Lurve? That is impressive! I think the computer can survive in very low tempts.. Not sure about the rest. I’m an IT girl and I know we have the AC on the severs 24/7.

In twisted pair cable, two insulated wires are twisted around each other which provides protection against noise. Explain. -Technology

Description : In twisted pair cable, two insulated wires are twisted around each other which provides protection against noise. Explain. -Technology

Last Answer : Twisting the cables keep them close together so that, any external magnetic fields must cross both cable at the same time, so the interference created in one cable is cancelled by the almost exact opposite amount of interference in the other.

Carefully read the following descriptions and identify what is being talked about. 1. It consists of two insulated wires twisted around each other, -Technology

Description : Carefully read the following descriptions and identify what is being talked about. 1. It consists of two insulated wires twisted around each other, -Technology

Last Answer : 1. Twisted pair cable2. Crosstalk3. Radiowave4. Wired communication channel5. Resource sharing

Can a panel apartment be insulated?

Description : Can panel homes be insulated?

Last Answer : Thermal insulation is usually applied from the outside. If you are thinking of soundproofing, they are usually used with a soundproofing sponge. You can try, but I don’t think it will insulate much.

Should the house be insulated? 45 cm wall thickness

Description : The situation is that the wall thickness is 45 cm (ytong), we can not dismantle the insulated house. Thank you in advance for your help.

Last Answer : I supposedly don't need to insulate it anymore, its thermal insulation is so good, but if you don't have a problem doing it, I think you should do it. The good can be even better and will definitely pay off over the years.