Description : The part of a fuse that melts and opens the circuit is made of _____________. A. copper and antimony B. steel and babbitt C. aluminum or beryllium alloy D. zinc or an alloy of tin and lead
Last Answer : Answer: D
Description : Which of the following is a light alloy? (A) Monel metal (B) Dow metal (C) German silver (D) Babbitt meta
Last Answer : (B) Dow metal
Description : Complete controller maintenance includes _____________. A. periodic testing of protective devices B. checking for loose or worn contacts and weak springs C. maintaining a sufficient supply of spare parts D. all of the above
Description : In a three-phase, squirrel-cage type, induction motor the rotating magnetic field is established by the _____________. A. current induced in the rotor windings B. application of a three-phase voltage ... caused by the induced current in the squirrel-cage bars with the magnetic field of the stator
Last Answer : Answer: B
Description : What induces a plant embryo a food supply and a protective covering?
Last Answer : Need answer
Description : What kind of plant has a protective covering around it's seeds?
Last Answer : Angiosperm
Description : What is called the protective covering of the brain?
Last Answer : Cranium
Description : Which of the following statements is correct? (a) Cornea consists of dense matrix of collagen and is the most sensitive portion of the eye. (b) Cornea is an external, transparent and protective ... elastin and can repair itself. (d) Cornea is convex, transparent layer which is highly vascularised.
Last Answer : (a) Cornea consists of dense matrix of collagen and is the most sensitive portion of the eye.
Description : Which meristem replaces epidermis as the protective covering?
Last Answer : Secondary meristem called periderm or cork cambium.
Description : In electronic circuitry, the abbreviation 'PCB' commonly means ______________. A. pulse coded binary B. printed circuit board C. poly-coated braid D. personal computer bits
Description : Tightly knit metal braid wire can be used with a printed circuit board when ___________. A. conductor flexibility is required B. desoldering components in the circuit C. electrically produced magnetic ... cause inaccuracies in adjacent components D. reactance in the circuit must be kept to a minimum
Description : The insulation of electric generators during short idle periods should be _____________. A. allowed to cool slowly to ambient temperatures B. flashed with direct current to remove any residual ... using strip or space heaters D. relieved of all capacitive charge by grounding the conductors
Last Answer : Answer: C
Description : With both ends of a three conductor cable disconnected and arranged without the conductors touching each other, an ohmmeter reading of 'zero' ohms between the ends of one conductor would indicate _____________. A. continuity B. a partial ground C. the resistance is infinite D. a short circuit
Last Answer : Answer: A
Description : The heating of conductors as a result of resistance in a distribution circuit causes a power loss expressed as _____________. A. line droop B. line loss C. IR drop D. hysteresis
Description : To minimize magnetic field interaction between electrical conductors in physical proximity, it is best to keep them ___________________. A. parallel and as close as possible to each other B. at right angles ... practicable from each other D. at right angles and as far as practicable from each other
Description : Pitched and sloping roofs are suitable for (A) Coastal regions (B) Plain regions (C) Covering large areas (D) All of the above
Last Answer : Option A
Description : In a faceplate-type motor starter, the starting arm is held in the 'OFF' position by a/an _____________. A. cotter pin B. magnet C. electrical circuit D. strong spring
Description : Which type of flux should be used when soldering electrical wire connections and electronic components? A. Silver flux B. Rosin flux C. Solid flux D. Acid flux
Description : . Most easily and cheaply available fibrous raw material for paper manufacture available in India is bamboo. The yield of pulp produced from fibrous raw material by mechanical process is about __________ percent. (A) 75 (B) < 10 (C) > 30 (D) 50
Last Answer : (B) < 10
Description : Paper pulp produced by Kraft/sulphate process is (A) Bleached easily (B) Dull white in color (C) Strong fibrous (D) Dark colored
Last Answer : (C) Strong fibrous
Description : Cellulose content of bamboo and ideal fibrous raw material for the manufacture of paper is __________ percent. (A) 10 (B) 50 (C) 80 (D) 95
Last Answer : (B) 50
Description : What are the common conductors in sequence with high conductivity?
Last Answer : a. Silver b. Silver copper alloy c. Copper (Hard down and Annealed) d. Gold e. Zinc f. Platinum g. Tin h. Aluminum i. Iron j. Brass k. Phosphorous bronze l. Nickel m. Lead n. Germanium silver o. Antimony p. Platinoid q. Mercury r. Bismuth s. Platinum iridium
Description : When maintenance personnel are working on electrical equipment, all supply switches should be secured in the open position and tagged specifically by the _____________. A. watch engineer B. chief engineer or first assistant C. chief electrician D. person performing the repair
Description : The emergency electrical power source on tank vessels over 500 GT on an international voyage, should be capable of continuous operation under emergency load for _____________. A. 6 hours B. 12 hours C. 18 hours D. 24 hours
Description : The electrical schematic illustrated in figure A, depicts a/an _____________. EL-0059 A. autotransformer B. Delta Wye transformer C. primary EMF generator D. potential transformer
Description : The electrical diagram shown in the illustration shows _____________. EL-0021 A. 'R1', 'R2', and 'R3' are connected is series B. 'R1', 'R2', and 'R3' are connected in parallel C. the voltages measured across ... if 'R1', 'R2' and 'R3' have different values D. the total resistance equals R1 + R2 + R3
Description : The electrical schematic shown in the illustration indicates the lighting feeder circuit is _____________. EL-0014 A. three phase, 450 volt, and 60 cycle B. three phase, 120 volt, and 60 cycle C. single phase, 120 volt, and 60 cycle D. not specified
Description : Electrical failures in motors are caused by the breakdown of insulation, which may be caused by _____________. A. penetration of moisture B. accumulation of dirt C. overheating D. all of the above
Description : A current-carrying conductor making electrical contact with a wiring conduit will be indicated by a _____________. A. high switchboard wattmeter reading B. totally dark switchboard ground detecting light C. low switchboard wattmeter reading D. all of the above
Description : The unit of electrical resistance is the _____________. A. ampere B. volt C. watt D. ohm
Description : The unit of electrical power is the _____________. A. ampere B. kilovolt C. watt D. farad
Description : In an alternating current electrical system, a low system power factor is a direct sign of _____________. A. wasted energy B. efficient operation C. a short in the exciter field windings D. an excessive number of minor system grounds
Description : A fuse will 'blow' if _____________. A. an electric motor is stopped suddenly by opening a switch B. the flow of current to the protection device is reversed C. the electrical current exceeds the rated value of the fuse D. unequal resistors are connected in parallel
Description : A device used in an electrical circuit to change alternating current to direct current, is known as a _____________. A. current transformer B. rectifier C. condenser D. shunt
Description : The electrical device shown in the illustration is a/an _____________. EL-0077 A. operating coil B. indicating lamp C. motor armature D. potentiometer
Description : An electrical connection between the wiring of an electric motor and its metal frame is known as a/an _____________. A. eddy current B. ground C. impedance D. flux leakage
Description : Electrical power is expressed in _____________. A. ohms B. volts C. amps D. watts
Description : A ground is indicated by the ground-detecting system on the main electrical switchboard. The FIRST step in locating the actual ground is to _____________. A. close all circuit breakers in ... ground detection system indicates normal C. change over generators D. check each circuit with a megohmmeter
Description : A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light
Description : The ground indicating light on the main electrical switchboard is indicating a ground. The best procedure for locating the grounded circuit is to _____________. A. trace the circuit paths while looking for ... a time, until the lights no longer indicate a ground D. check all circuits for continuity
Description : When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B ... an increase in the line voltage D. decrease, causing an increase in the line current
Description : Electrical insulation is classed by the _____________. A. International Association of Electrical Manufacturers B. approximate operating voltage and current expected C. U.S. Coast Guard D. temperature stability of the manufacturing material(s)
Description : Complete maintenance of electrical motors should include periodic checks for machine _____________. A. vibration B. watertight integrity C. speed droop D. reactive power
Description : The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens ... wasted if full loading is not utilized D. power factor correction methods are load dependent
Description : Cleaning of electrical insulation should be _____________. A. done every six months B. accomplished every 12 months C. determined by need and not the calendar D. performed whenever the electrician is not otherwise busy
Description : The electrical supply applied to the anodes shown in the illustration is _____________. EL-0090 A. low voltage, high current DC B. low voltage, high current AC C. high voltage, low current DC D. high voltage, low current AC
Description : The 'E/P converter' shown in the illustration receives a _____________. EL-0096 A. steady pressure signal and produces a programmed electrical output B. variable electrical signal ... an inverse temperature correction D. variable pressure signal and produces a corresponding electrical output
Description : A testing device called a 'growler' is being used to locate a shorted coil in the stator of an AC electrical machine. When the 'feeler' is moved over a slot containing the shorted coil _____________. ... . the meter needle will be deflected to zero D. the meter needle will be deflected to full-scale
Description : A ground in an electrical circuit outside the engine room _____________. A. cannot be detected under normal conditions B. is of no consequence to engineering personnel C. is indicated at the branch circuit breaker panel D. is indicated by the ground detecting lamps on the main switchboard
Description : The part of the shipboard electrical system used to control the distribution of power to the branch circuits, is the _____________. A. bridge control panel B. disconnect links C. governor relay box D. main switchboard