Description : The component used for tuning a radio is basically a variable – (1) Resistor (2) Condenser (3) Inductor (4) Transformer
Last Answer : (2) Condenser Explanation: A tuning capacitor or tuning condenser is a variable capacitor used in an electronic circuit of a radio. It usually connects in parallel to a loop antenna and its capacitance may be intentionally and repeatedly changed mechanically or electronically.
Description : The 'Choke' used with a tube light is basically – (1) an inductor (2) a capacitor (3) a transformer (4) a resistor
Last Answer : (1) an inductor Explanation: In electronics, a choke is an inductor used to block higher-frequency alternating current (AC) in an electrical circuit, while passing lower-frequency or direct ... created by suddenly interrupting the current in choke, which is connected in series with the tubelight.
Description : The ‘Choke’ used with a tube light is basically (1) an inductor (2) a capacitor (3) a transformer (4) a resistor
Last Answer : an inductor
Description : A component that allows only unidirectional current to pass through it is A. resistor B. inductor C. transformer D. diode
Last Answer : diode
Description : Draw the symbol of i) Iron core inductor ii) variable capacitor iii) resistor iv) Ferrite core inductor
Last Answer : Iron core inductor: Ferrite core inductor:
Description : Device used to store energy in electrical circuits is A. resistor B. inductor C. capacitor D. diode
Last Answer : capacitor
Description : insulator which is placed between 2 plates of capacitor isA. electric B. dielectric C. inductor D. resistor
Last Answer : dielectric
Description : A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.
Last Answer : ANSWER: X -- CURRENT WILL LAG BY 26 DEGREES.
Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling
Last Answer : A) Wave traps in each stage
Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Last Answer : Answer: C
Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Last Answer : Answer: A
Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Description : The electric charge is stored in a device called: (1) Inductor (2) Capacitor (3) Resister (4) Transformer
Last Answer : (2) Capacitor Explanation: A capacitor is a passive twoterminal electronic component that stores electrical energy in an electric field. The effect of a capacitor is known as capacitance.
Description : What is the phase angle of an ohm inductor in series with an ohm resistor connected to a 5 KHz source?
Last Answer : You need to provide values of resistor and inductor etc to find the phase angle.
Description : The most inefficient method of voltage reduction, from the standpoint of power loss, even when placed in series with the load, is the use of a/an ____________. A. capacitor B. inductor C. resistor D. transistor
Description : The most inefficient method of voltage reduction from the stand point of power loss, is a/an _____________. A. capacitor in series with the load B. inductor in series with the load C. capacitor and inductor in series with the load D. resistor in series with the load
Last Answer : Answer: D
Description : To electrically decrease the length of an antenna. A. add an inductor in series B. add an inductor in parallel C. add a resistor in series D. add a capacitor in series
Last Answer : D. add a capacitor in series
Description : Increasing the electrical length of an antenna means A. add an inductor in parallel B. add a capacitor in series C. add an inductor series D. add a resistor is series
Last Answer : C. add an inductor series
Description : How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna
Last Answer : D. By connecting an inductor in series with the antenna
Description : State the applications and specification of (i) Resistor (ii) Capacitor (iii)Inductor
Last Answer : Application of resistor: 1.Resistors are used in high frequency instrument. 2.Resistor is used in power control circuit. 3.It is used in DC power supplies. 4.Resistors are used ... DC Current 3.Electromagnetic Interference (EMI) 4.Magnetic Saturation Flux Density 5.Curie Temperature
Description : The following is an amplifying device : (1) a transformer (2) a transistor (3) a diode (4) a resistor
Last Answer : (2) a transistor Explanation: A transistor is a semiconductor device used to amplify or switch electronic signals and electrical power.
Description : Ratio of voltages is inverse ratio of the A. transformer B. resistor C. iron core D. current
Last Answer : current
Description : In transformer, alternating current is induced inA. primary coil B. secondary coil C. iron core D. resistor
Last Answer : primary coil
Description : A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms
Last Answer : ANSWER: W -- 25 OHMS
Description : Basically, a magnetic amplifier is a saturable reactor with the addition of _____________. A. AC to the bias winding B. variable capacitance to all windings C. eddy current protectors D. a rectifier in the load circuit
Description : A Hay bridge measures inductance by comparing an inductor to what component?
Last Answer : A capacitor.
Description : The shear resistance of a soil is constituted basically of the following component. (A) The frictional resistance to translocation between the individual soil particles at their contact point (B) To the ... (C) Cohesion and adhesion between the surfaces of the soil particles (D) All the above
Last Answer : Answer: Option D
Description : Which of the following devices converts electrical energy into mechanical energy? (a) Dynamo (b) Transformer (c) Electric motor (d) Inductor
Last Answer : Ans:(c)
Description : The symbol shown as figure 'A' represents a/an ____________. EL-0059 A. transformer B. coil C. shunt field D. inductor
Description : What is the main component in a boiler a) steam b) heat c) pressure condenser d) combination
Last Answer : a) steam
Description : A device used in an electrical circuit to change alternating current to direct current, is known as a _____________. A. current transformer B. rectifier C. condenser D. shunt
Last Answer : Answer: B
Description : Which of the following equipment, for regulating the voltage in distribution feeder, will be most economical ? (a) Static condenser (b) Synchronous condenser (c) Tap changing transformer (d) Booster transformer
Last Answer : (d) Booster transformer
Description : When a vibrating tuning fork is placed on a table, a loud sound is heard. This is due to – (1) reflection (2) refraction (3) forced vibrations (4) damped vibrations
Last Answer : (3) forced vibrations Explanation: The tendency of one object to force another adjoining or interconnected object into vibrational motion is referred to as a forced vibration. In the case of the ... forced into vibration. This causes an increase in the amplitude and thus loudness of the sound.
Description : Unwanted signal that distorts a transmitted signal is called A. analogue B. noise C. digital D. tuning
Last Answer : noise
Description : Decrease in strength of signal is known as A. tuning B. modulation C. attenuation D. amplification
Last Answer : attenuation
Description : As the temperature of the air increases from 0 degrees C to 20 degrees C, the wavelength of a sound made by a tuning fork of fixed frequency does which of the following? Does the wavelength w) increase x) decrease y) remain the same z) increase up to a maximum, then remain constant
Last Answer : ANSWER: W -- INCREASE
Description : When a vibrating tuning fork is placed on a table, a loud sound is heard. This is due to : (1) reflection (2) refraction (3) forced vibrations (4) damped vibrations
Last Answer : forced vibrations
Description : What is represented by the electric symbol figure 'D' in the illustration? EL-0005 A. Fuse B. Plug-in contact resistor C. Variable capacitor D. Electrolytic capacitor
Description : Which of the listed devices may be used as a digital device? A. variable resistor B. diode C. strain gauge D. thermistor
Description : The advantage(s) of the method of D.C. motor speed control shown in the illustration is/are ______________. EL-0101 A. elimination of armature starting resistor losses B. elimination of speed instability with variable loads C. the ease of reversing motor direction D. all of the above
Description : To carry out an insulation resistance test, one terminal of the megohmmeter should be connected to the winding, with the other terminal being connected to the ____________________. A. power supply B. variable resistor C. frame of the machine D. armature
Description : The arrow drawn through the resistor shown in the illustration indicates that it is _____________. EL-0086 A. for use in low power applications B. a carbon composition type C. a wire-wound type D. one whose resistance is variable
Description : An adjustable resistor, whose resistance can be changed without opening the circuit in which it is connected, is called a _____________. A. bleeder resistor B. rheostat C. bridge D. variable shunt strip
Description : . Which type of variable resistor should you select for controlling a large amount of current?
Last Answer : The rheostat.
Description : Define resistor and draw symbol of variable resistor.
Last Answer : Resistor: A resistor is an electrical component that limits or regulates the flow of electrical current in an electronic circuit. Symbol of variable resistor:
Description : A two-terminal variable resistor is known as a? A.potentiometer B.thermistor C.rheostat D.wiper
Last Answer : A two-terminal variable resistor is known as a? A.potentiometer B.thermistor C.rheostat D.wiper
Description : Which component is responsible for energizing solenoid 'B1-B2' and releasing the brake for the winch motor shown in the illustration? EL-0102 A. Contactor '3M' B. A spring not shown in the schematic diagram C. Resistor 'B2-R1' D. Relay 'FR-B.O.'
Description : In troubleshooting a circuit in a console, you find that a resistor may be faulty. Which of the precautions listed must be observed when using an ohmmeter to carry out this test? A. Correct polarity ... D. The resistor's circuit must be de-energized and at least one end of the component isolated.
Description : While troubleshooting a circuit in an engine room central control console, a resistor is suspected of being faulty. Which of the following precautions must be observed if an ohmmeter is to be used to ... of the component isolated. D. The meter case must be grounded prior to attaching the leads.
Description : As shown in the illustration, the direction of electron flow through the component is _______. EL-0079 A. from terminal 'B' to terminal 'A' B. from terminal 'A' to terminal 'B' C. determined by the polarity of the applied voltage D. opposite from that in a resistor