How Do You Carry Out Piping For A Different Pressure Flow Transmitter On Liquids, Gas And Steam Services? Why?

How Do You Carry Out Piping For A Different Pressure Flow
Transmitter On Liquids, Gas And Steam Services? Why?
by

1 Answer

Answer :

Liquid lines: On liquid lines the transmitter is mounted below the orifice plate. Since liquids have a property of self draining.
Gas Service: On gas service the transmitter is mounted above the orifice plate because Gases have a property of self venting and secondly condenlate formation.
Steam Service: On steam service the transmitter is mounted below the orifice plate with condenlate pots. The pots should be at the same level.
by

Related questions

How Would You Do Glycol Filling Or Fill Seal Liquids In Seal Pots 7 Draw And Explain?

Description : How Would You Do Glycol Filling Or Fill Seal Liquids In Seal Pots 7 Draw And Explain?

Last Answer : The procedure for glycol filling is : 1. Close the primary isolation valves. 2. Open the vent on the seal pots. 3. Drain the use glycol if present. 4. Connect a hand pump on L.P. side while ... 9. Close the seal pot vent valves. 10. Close equalizer valve. 11. Open both the primary isolation valves.

How Do You Do A Zero Check On A D.p. Transmitter?

Description : How Do You Do A Zero Check On A D.p. Transmitter?

Last Answer : Close one of the valve either H.P. or L.P. open the equalizing valve. The O/P should read zero.

How Do You Calibrate A D. P. Transmitter?

Description : How Do You Calibrate A D. P. Transmitter?

Last Answer : The following steps are to be taken which claribrating : 1. Adjust zero of the Xmtrs. 2. Static preasure test: Give equal pressure on both sides of the transmitter. Zero should not shift. If ... pressure to high pressure side of the transmitter and adjust the span.  Adjust zero again if necessary.

Why Is Flow Measured In Square Root?

Description : Why Is Flow Measured In Square Root?

Last Answer :  Flow varies directly as the square root of different pressure F = K square root of ΔP.  Since this flow varies as the square root of differential pressure the pen does not directly indicate flow.  The flow can be determined by taking the square root of the pen. Say the pen reads 50% of chart.

An Operator Tells You That Flow Indication Is More? How Would You Start Checking?

Description : An Operator Tells You That Flow Indication Is More? How Would You Start Checking?

Last Answer : 1. First flushing the transmitter. Flush both the impulse lines. Adjust the zero by equalizing if necessary. If still the indication is more then. 2. Check L.P. side for choke. If that is clean then. 3. Check the leaks on L.P. side. If not. 4. Calibrate the transmitter.

What Are The Primary Elements Usedfor Flow Measurement?

Description : What Are The Primary Elements Usedfor Flow Measurement?

Last Answer : The primary elements used for flow measurement are: 1. Orifice Plate. 2. Venturi tube. 3. Pitot tube. 4. Annubars. 5. Flow Nozzle. 6. Weir & Flumes.

What Are The Different Types Of Orifice Plates And State Their Uses?

Description : What Are The Different Types Of Orifice Plates And State Their Uses?

Last Answer : The different types of orifice plates are: 1. Concentric. 2. Segmental. 3. Eccentric. CONCENTRIC: The concentric orifice plate is used for ideal liquid as well as gases and steam service. This orifice ... hole in the form segment of a circle. This is used for colloidal and sherry flow measurement.

How Will You Vent Air In The D.p. Cell? What If Seal Pots Are Used?

Description : How Will You Vent Air In The D.p. Cell? What If Seal Pots Are Used?

Last Answer : 1. Air is vented by opening the vent plugs on a liquid service transmitter. 2. On services where seal pots are used isolate the primary isolation valves and open the vent valves. Fill the line from the transmitter drain plug with a pump.

How Do You Calculate New Factor From New Range Using Old Factor And Old Range?

Description : How Do You Calculate New Factor From New Range Using Old Factor And Old Range?

Last Answer : New Factor = _!New Range Old Factor = _IOld Range Flow = K_!Range Q = Factor X Unit Flow New Factor = Old Factor I _IOld Range X _/New Range.

What Is The Seal Liquid Used For Filling Impulse Lines On Crude And Viscous Liquid?

Description : What Is The Seal Liquid Used For Filling Impulse Lines On Crude And Viscous Liquid?

Last Answer : Glycol.

How Do You Identify The H. P. Side Or Inlet Of An Orifice Plate In Line?

Description : How Do You Identify The H. P. Side Or Inlet Of An Orifice Plate In Line?

Last Answer : The marking is always done H. P. side of the orifice tab which gives an indication of the H.P.side.

What Is Bernoulli’s Theoram And Where It Is Applicable?

Description : What Is Bernoulli’s Theoram And Where It Is Applicable?

Last Answer : Bernoulli’s theoram states the “total energy of a liquid flowing from one point to another remains constant.” It is applicable for non compressible liquids.

Why Is The Orifice Tab Provided?

Description : Why Is The Orifice Tab Provided?

Last Answer : The orifice tab is provided due to the following reasons: 1. Indication of an orifice plate in a line. 2. The orifice diameter is marked on it. 3. The material of the orifice plate. 4. The tag no. of the orifice plate. 5. The mark the inlet of an orifice.

How Do You Identify An Orifice In The Pipe Line?

Description : How Do You Identify An Orifice In The Pipe Line?

Last Answer : An orifice tab is welded on the orifice plate which extends our of the line giving an indication of the orifice plate.

Define All The Process Variable And State Their Unit Of Measurement?

Description : Define All The Process Variable And State Their Unit Of Measurement?

Last Answer : 1. FLOW: Kg I hr, Litter I min, Gallon I min. M3 I NM3 I HR. (GASES) 2. PRESSURE: Force acting per unit Area. P = F/A Units: Bar I Pascals I Kg I CM I, Pounds 3. LEVEL: ... Degree Farenheit, Degree Kelvin, Degree Rankin. 5. QUALITY: It deals with analysis PH, % C02, % 02, Conductivity, Viscosity.

What Are The Process Variable?

Description : What Are The Process Variable?

Last Answer : The process Variable are: 1. Flow 2. Pressure 3. Temperature 4. Level 5. Quality i. e. % D2, C02, PH etc.

What do the piping connections to a steam boiler provide?

Description : What do the piping connections to a steam boiler provide?

Last Answer : Need answer

How can problems of "excessive vibration or noise" due to piping strain be avoided on steam turbines?

Description : How can problems of "excessive vibration or noise" due to piping strain be avoided on steam turbines?

Last Answer : 1. The inlet as well as exhaust steam lines should be firmly supported to avoid strains from being imposed on the turbine. 2. Adequate allowance should be made for expansion of steam pipes due to heat.

Steam distillation is not recommended to be used, if the (A) Azeotropic mixture is to be separated and the final product is miscible with water (B) Liquids decompose, if distilled directly at atmospheric pressure (C) Material cannot be distilled by indirect heating even under low pressure, because of the high boiling temperature (D) Material to be distilled is thermally unstable or has the tendency to react with other components associated with it, at the boiling temperature

Description : Steam distillation is not recommended to be used, if the (A) Azeotropic mixture is to be separated and the final product is miscible with water (B) Liquids decompose, if ... unstable or has the tendency to react with other components associated with it, at the boiling temperature

Last Answer : (A) Azeotropic mixture is to be separated and the final product is miscible with water

Vibrations in the tubes of a shell and tube heat exchanger is induced due to the (A) Flow of fluid on the tube and shell sides (B) Oscillations in the flow of shell/tube sides fluid (C) Vibrations transmitted through piping and/or supports due to external reasons (D) All (A), (B) and (C)

Description : Vibrations in the tubes of a shell and tube heat exchanger is induced due to the (A) Flow of fluid on the tube and shell sides (B) Oscillations in the flow of shell/tube sides fluid (C) Vibrations ... piping and/or supports due to external reasons (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Two piping system are said to be equivalent, when the __________ are same. (A) Fluid flow rate & friction loss (B) Length & friction factor (C) Diameter & friction factor (D) Length & diameter

Description : Two piping system are said to be equivalent, when the __________ are same. (A) Fluid flow rate & friction loss (B) Length & friction factor (C) Diameter & friction factor (D) Length & diameter

Last Answer : (A) Fluid flow rate & friction loss

For joints in service in the creep range which of the following is recommended by ASME B16.5? a) Replacement of the joint after 1,000,000 hours of service. b) Periodic tightening of the bolts to prevent leakage. c) Immediate replacement is recommended if the material operates in the creep range. d) Regular flow detection inspection of the piping to fitting welds.

Description : For joints in service in the creep range which of the following is recommended by ASME B16.5? a) Replacement of the joint after 1,000,000 hours of service. b) Periodic tightening of ... the material operates in the creep range. d) Regular flow detection inspection of the piping to fitting welds.

Last Answer : b) Periodic tightening of the bolts to prevent leakage.

Piping in a soil mass is a) Erosion of subsoil by the high velocities of flow of water through it when such velocities exceed a certain limit* b) Caused due to very low exit gradient c) Due to continuous passage of water through a series of well connected pores d) Due to loss of the strength of cohesion less soil because of upward flow of of water

Description : Piping in a soil mass is a) Erosion of subsoil by the high velocities of flow of water through it when such velocities exceed a certain limit* b) Caused due to very low exit gradient c) ... connected pores d) Due to loss of the strength of cohesion less soil because of upward flow of of water

Last Answer : a) Erosion of subsoil by the high velocities of flow of water through it when such velocities exceed a certain limit*

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

Pick out the wrong statement. (A) The binary diffusivity in liquids is of the order of 10 -5 cm2 /sec (B) Molecular diffusion in solid is much faster than that in liquids (C) Particles movement from higher concentration to lower concentration takes place in diffusion process (D) According to Poiseuille's law, the permeability decreases with increase in temperature for flow of a gas through a given capillary

Description : Pick out the wrong statement. (A) The binary diffusivity in liquids is of the order of 10 -5 cm2 /sec (B) Molecular diffusion in solid is much faster than that in liquids ( ... Poiseuille's law, the permeability decreases with increase in temperature for flow of a gas through a given capillary

Last Answer : (B) Molecular diffusion in solid is much faster than that in liquids

Inside the distillation column, the (A) Driving force for the vapour flow is the pressure drop (B) Liquids are not always at their bubble points (C) Pressure increases gradually from bottom to the top of the column (D) None of these

Description : Inside the distillation column, the (A) Driving force for the vapour flow is the pressure drop (B) Liquids are not always at their bubble points (C) Pressure increases gradually from bottom to the top of the column (D) None of these

Last Answer : (A) Driving force for the vapour flow is the pressure drop

In an operating distillation column, the (A) Vapors and liquids are at their dew point and bubble point respectively (B) Driving force for the liquid flow is its specific weight (C) Driving force for the vapor flow is the pressure drop, as the pressure decreases gradually from the bottom to the top of the column (D) Highest temperature is encountered at the top of the column

Description : In an operating distillation column, the (A) Vapors and liquids are at their dew point and bubble point respectively (B) Driving force for the liquid flow is its specific weight (C) Driving force for ... bottom to the top of the column (D) Highest temperature is encountered at the top of the column

Last Answer : (C) Driving force for the vapor flow is the pressure drop, as the pressure decreases gradually from the bottom to the top of the column

In a counter-current liquid extractor (A) Both liquids flow at fixed rate (B) Both liquids can have any desired flow rate (C) Only one of the liquids may be pumped at any desired rate (D) Liquid’s flow rate depends upon the temperature and pressure

Description : In a counter-current liquid extractor (A) Both liquids flow at fixed rate (B) Both liquids can have any desired flow rate (C) Only one of the liquids may be pumped at any desired rate (D) Liquid’s flow rate depends upon the temperature and pressure

Last Answer : (C) Only one of the liquids may be pumped at any desired rate

Venturimeter is used to measure: (1) rate of flow of liquids (2) liquid pressure (3) surface tension (4) liquid density

Description : Venturimeter is used to measure: (1) rate of flow of liquids (2) liquid pressure (3) surface tension (4) liquid density

Last Answer : rate of flow of liquids

Gas Piping Installation?

Description : Gas Piping Installation?

Last Answer : form_title=Gas Piping Installation form_header=8883 How would you best describe the scope of the work? (Select all that apply)*= [] Repair leak in gas line [] Replace old gas lines [] Appliance gas ... Dryer [] Stove/oven/cooktop [] Central heating system [] Water heater [] Generator [] Other

Different Types of Flanges Used in Piping Applications?

Description : Different Types of Flanges Used in Piping Applications?

Last Answer : Different Types of Flanges Slip on Flanges Weld Neck Flanges Blind Flanges Socket Weld Flanges Lap Joint Flanges Threaded Flanges Orifice Flanges Spectacle Blind Flanges Reducing Flanges Forged Flanges ANSI ... If anyone wants to buy any of these Flanges then Contact us: sales@nufitpiping .com

Pick out the wrong statement. (A) Trouton's ratio of non-polar liquids is calculated using Kistyakowsky equation (B) Thermal efficiency of a Carnot engine is always less than 1 (C) An equation relating pressure, volume and temperature of a gas is called ideal gas equation (D) None of these

Description : Pick out the wrong statement. (A) Trouton's ratio of non-polar liquids is calculated using Kistyakowsky equation (B) Thermal efficiency of a Carnot engine is always less than 1 (C) An equation relating pressure, volume and temperature of a gas is called ideal gas equation (D) None of these

Last Answer : (C) An equation relating pressure, volume and temperature of a gas is called ideal gas equation

Hot wire anemometer is used to measure (A) Pressure in gases (B) Liquid discharge (C) Pressure in liquids (D) Gas velocities

Description : Hot wire anemometer is used to measure (A) Pressure in gases (B) Liquid discharge (C) Pressure in liquids (D) Gas velocities

Last Answer : Answer: Option D

Pick out the wrong statement. (A) A fluid mass is free from shearing forces, when it is made to rotate with a uniform velocity(B) Newton's law of viscosity is not applicable to the turbulent flow of fluidwith linear velocity distribution(C) Laminar flow of viscous liquids is involved in the lubrication of varioustypes of bearings(D) Rise of water in capillary tubes reduces with the increasing diameter ofcapillary tubes

Description : Pick out the wrong statement. (A) A fluid mass is free from shearing forces, when it is made to rotate with a uniform velocit (B) Newton's law of viscosity is not applicable to the ... types of bearings (D) Rise of water in capillary tubes reduces with the increasing diameter of capillary tubes

Last Answer : (B) Newton's law of viscosity is not applicable to the turbulent flow of fluid with linear velocity distribution

Piping is carried out in a. Chrysanthemum b. Rose c. Gladiolus d. Carnation

Description : Piping is carried out in a. Chrysanthemum b. Rose c. Gladiolus d. Carnation

Last Answer : Carnation

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for counter flow and parallel flow can be theoretically same when any one of the fluids (hot or cold fluid) passes through the heat exchanger at constant temperature (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs (D) Phase change in case of a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Description : Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for ... a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Last Answer : (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs

Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation (B) Cavitation may be caused due to boiling of liquid by decreasing the pressure resulting in formation & collapse of vapor cavities (C) Cavitation begins at higher static pressure and lower velocity in larger diameter pipelines resulting in audible noise(D) Large scale cavitation cannot damage pipeline, restrict fluid flow anddamage steam turbine blades

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

A fountain pen works on the principle of (1) Flow of liquids from higher to lower potential (2) Capillary action (3) Bernoulli's principle (4) Viscosity of liquids

Description : A fountain pen works on the principle of (1) Flow of liquids from higher to lower potential (2) Capillary action (3) Bernoulli's principle (4) Viscosity of liquids

Last Answer : (2) Capillary action Explanation: A fountain pen is a nib pen that, unlike its predecessor the dip pen, contains an internal reservoir of water-based liquid ink. The pen draws ink from the ... to flow in narrow spaces without the assistance of, and in opposition to external forces like gravity.

During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Description : During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Last Answer : (A) Density of the liquid

Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Description : Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Last Answer : (A) Is suitable for mixing low viscosity liquids

Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Description : Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Last Answer : (A) Axial flow mixers

04. All the gases are considered to have compressible flow and all the liquids are considered to have incompressible flow. A) Correct B) Incorrect

Description : 04. All the gases are considered to have compressible flow and all the liquids are considered to have incompressible flow. A) Correct B) Incorrect

Last Answer : A

The Euler's equation for the motion of liquids is based upon the assumption that (A) The fluid is non - viscous, homogeneous and incompressible (B) The velocity of flow is uniform over the section (C) The flow is continuous, steady and along the stream line (D) All of the above

Description : The Euler's equation for the motion of liquids is based upon the assumption that (A) The fluid is non - viscous, homogeneous and incompressible (B) The velocity of flow is uniform over the section (C) The flow is continuous, steady and along the stream line (D) All of the above

Last Answer : Answer: Option D

The term "laminar flow" is most often associated with the description of: w) conduction of sound by waves x) current flow in transistors y) effects of viscosity of liquids z) passage of light rays through a liquid

Description : The term "laminar flow" is most often associated with the description of: w) conduction of sound by waves x) current flow in transistors y) effects of viscosity of liquids z) passage of light rays through a liquid

Last Answer : ANSWER: Y -- EFFECTS OF VISCOSITY OF LIQUIDS

A fountain pen works on the principle of (1) flow of liquids from higher to lower potential (2) capillary action (3) Bernoulli’s principle (4) Viscosity of liquids

Description : A fountain pen works on the principle of (1) flow of liquids from higher to lower potential (2) capillary action (3) Bernoulli’s principle (4) Viscosity of liquids

Last Answer : capillary action

Late afternoons I often bathe. I'll soak in water piping hot. My essence goes through my see through clothes. Used up am I; I've gone to pot. What am I? -Riddles

Description : Late afternoons I often bathe. I'll soak in water piping hot. My essence goes through my see through clothes. Used up am I; I've gone to pot. What am I? -Riddles

Last Answer : I'm a tea bag!

What can be done to avoid fire hazards caused by bad piping?

Description : What can be done to avoid fire hazards caused by bad piping?

Last Answer : One way is to check for bad leakage. A water coming from the leakage can seep into the area of electrical wiring that could cause fire. Keep an eye for high water bill or any form of discoloration that might indicate leak to avoid hazards.

What is the Piping colour code of N butanol solvent?

Description : What is the Piping colour code of N butanol solvent?

Last Answer : What is the answer ?

What is the N butanol piping colour code?

Description : What is the N butanol piping colour code?

Last Answer : What is the answer ?