Would a low-temp glue gun be better than a high-temp glue gun for plastics?

Would a low-temp glue gun be better than a high-temp glue gun for plastics?
by

1 Answer

Answer :

A low temperature glue gun would be best because there would be less damage to the plastic from the heated glue.
by

Related questions

How to Use a Glue Gun

Description : How to Use a Glue Gun

Last Answer : How to Use a Glue Gun The glue gun is a staple in arts and crafts projects. However, the improper use of a glue gun can lead to a messy project, or worse, a bad burn. Here's how to use a ... Once the glue has reverted back to its solid form, scrape the excess off using your finger or any hard edge.

Pick up the correct statement from the following: (A) Plastics have generally low melting point (B) The coefficient of thermal expansion of plastics is about three times than that of steel (C) The acoustical boards prepared by impregnating fibre-glass with phenolic resins has absorption coefficient of about 0.67 (D) All the above

Description : Pick up the correct statement from the following: (A) Plastics have generally low melting point (B) The coefficient of thermal expansion of plastics is about three times than that of steel (C) ... fibre-glass with phenolic resins has absorption coefficient of about 0.67 (D) All the above

Last Answer : Answer: Option D

What types of bonnets would you use of high temp. and very low temp. ?

Description : What types of bonnets would you use of high temp. and very low temp. ?

Last Answer : High temperature: Bonnets are provided with radiation fins to prevent glad packing from getting damaged.  On very low temperature: Extended bonnets are used to prevent gland packing from getting freezed

Creep is not exhibited at low temperature by (A) Rubber (B) Acrylics (C) Lead (D) Plastics

Description : Creep is not exhibited at low temperature by (A) Rubber (B) Acrylics (C) Lead (D) Plastics

Last Answer : (C) Lead

Plastics as a material of construction suffer from the drawback of low (A) Machinability (B) Density (C) Strength (D) Plastic deformatio

Description : Plastics as a material of construction suffer from the drawback of low (A) Machinability (B) Density (C) Strength (D) Plastic deformatio

Last Answer : Option C

Why is it better to use plant and animal based products in place of petroluem and plastics?

Description : Why is it better to use plant and animal based products in place of petroluem and plastics?

Last Answer : This is my midterm essay question which I have researched on my own. But I am at a loss.

low temp for cauliflower plants ?

Description : low temp for cauliflower plants ?

Last Answer : Need Answer

what is low temp for plumeria?

Description : what is low temp for plumeria?

Last Answer : Need Answer

What is better: room temp water or ice water?

Description : What is better: room temp water or ice water?

Last Answer : Room temp. I got sensitive teeth and i love to gulp water down

Pick out the correct statement. (A) Plastics are good conductors of heat and electricity (B) All the polymers are highly crystalline in nature (C) Polymers can be vaporised by heating to a very high temperature (D) The liquid polymer becomes greasy, then waxy and finally solid on increasing the degree of polymerisation

Description : Pick out the correct statement. (A) Plastics are good conductors of heat and electricity (B) All the polymers are highly crystalline in nature (C) Polymers can be vaporised by heating to ... D) The liquid polymer becomes greasy, then waxy and finally solid on increasing the degree of polymerisation

Last Answer : (D) The liquid polymer becomes greasy, then waxy and finally solid on increasing the degree of polymerisation

Plastics are (A) Used in very high temperature applications (B) Non-biodegradable (C) Not suitable for drainage pipe manufacture (D) All (A), (B) & (C)

Description : Plastics are (A) Used in very high temperature applications (B) Non-biodegradable (C) Not suitable for drainage pipe manufacture (D) All (A), (B) & (C)

Last Answer : (B) Non-biodegradable

Exposure to __________ accelerates the degradation of plastics. (A) Ultraviolet radiation (B) High atmospheric temperature (C) High ambient temperature (D) Damp atmosphere

Description : Exposure to __________ accelerates the degradation of plastics. (A) Ultraviolet radiation (B) High atmospheric temperature (C) High ambient temperature (D) Damp atmosphere

Last Answer : A) Ultraviolet radiation

Plastics are (A) Good conductors of heat. (B) Good conductors of electricity. (C) Bad conductors of electricity. (D) High density.

Description : Plastics are (A) Good conductors of heat. (B) Good conductors of electricity. (C) Bad conductors of electricity. (D) High density.

Last Answer : (C) Bad conductors of electricity.

Does hot glue work better on pop sticks then wood glue?

Description : Does hot glue work better on pop sticks then wood glue?

Last Answer : Hot glue will not work as good on pop sticks as wood glue, which will provide much better bonding.

Statement -1 `Al_(2)O_(3)` is converted in to Al by reductin with carbon at high temp.statement -2: Carbon has grater affinity for oxygen than alumium

Description : Statement -1 `Al_(2)O_(3)` is converted in to Al by reductin with carbon at high temp.statement -2: Carbon has grater affinity for oxygen than alumium

Last Answer : Statement -1 `Al_(2)O_(3)` is converted in to Al by reductin with carbon at high temp. ... -2: Carbon has grater affinity for oxygen than alumium .

On a cold day when the room temperature is 15°C, the metallic cap of a pen becomes much colder than its plastic body, though both are at the same temperature of 15°C, because – (1) metals have higher thermal capacity than plastics (2) plastics have a lower density than metals (3) metals are good conductors of heat (4) plastics have a higher thermal conductivity than metals

Description : On a cold day when the room temperature is 15°C, the metallic cap of a pen becomes much colder than its plastic body, though both are at the same temperature of 15°C, because - (1) metals ... metals (3) metals are good conductors of heat (4) plastics have a higher thermal conductivity than metals

Last Answer : (3) metals are good conductors of heat Explanation: On a chilly day, the room temperature is lower than our body temperature. Since metals have a higher coefficient of thermal conductivity than plastic, they ... from our fingers will flow to the metal cap much more quickly than to the plastic body.

Pick out the wrong statement. (A) Pure rubber is as useless as pure gold as a material of construction (B) Thermal conductivity of aluminium is higher than that of copper; henceit is increasingly used for utensil making(C) Copper has poor weldability(D) Reinforced plastics are made from both thermoplastic as well asthermosetting plastics

Description : Pick out the wrong statement. (A) Pure rubber is as useless as pure gold as a material of construction (B) Thermal conductivity of aluminium is higher than that of copper; henceit is ... has poor weldability (D) Reinforced plastics are made from both thermoplastic as well as thermosetting plastics

Last Answer : (B) Thermal conductivity of aluminium is higher than that of copper; henceit is increasingly used for utensil making

On a cold day when the room temperature is 15°C, the metallic cap of a pen becomes much colder than its plastic body, though both are at the same temperature of 15°C, because : (1) metals have higher thermal capacity than plastics (2) plastics have a lower density than metals (3) metals are good conductors of heat (4) plastics have a higher thermal conductivity than metals

Description : On a cold day when the room temperature is 15°C, the metallic cap of a pen becomes much colder than its plastic body, though both are at the same temperature of 15°C, because : (1) metals ... metals (3) metals are good conductors of heat (4) plastics have a higher thermal conductivity than metals

Last Answer : metals are good conductors of heat

Pick out the wrong statement. (A) Low intensity explosives are also called propellants, whereas high intensity explosive are called detonators (B) Gun powder comprises of 75% salt petre, 15% charcoal and 10% sulphur (C) Lead azide is a popular military explosive (D) TNT is a hygroscopic explosive having very high melting point and is non-toxic to human being

Description : Pick out the wrong statement. (A) Low intensity explosives are also called propellants, whereas high intensity explosive are called detonators (B) Gun powder comprises of 75% salt petre, 15% charcoal ... TNT is a hygroscopic explosive having very high melting point and is non-toxic to human being

Last Answer : (D) TNT is a hygroscopic explosive having very high melting point and is non-toxic to human being

High white cell count, abdominal pain & high temp?

Description : High white cell count, abdominal pain & high temp?

Last Answer : Wow, I would be very upset at not being listened to. These symptoms can mean anything from kidney stones to an ectopic pregnancy. You need to get a second opinion.

What is the high temp for Atlantic City New Jersey?

Description : What is the high temp for Atlantic City New Jersey?

Last Answer : 63.9 oF -mks

The gypsum is added to the cement for (a) Providing high strength to the cement (b) Controlling the initial setting time of cement. (c) Lowering the clinkering temp of cement (d) All the above.

Description : The gypsum is added to the cement for (a) Providing high strength to the cement (b) Controlling the initial setting time of cement. (c) Lowering the clinkering temp of cement (d) All the above.

Last Answer : (b) Controlling the initial setting time of cement.

I need ways to test/get data about homemade plastics. What can I do with Flexural Strength and Flexural Modulus...

Description : I need ways to test/get data about homemade plastics. What can I do with Flexural Strength and Flexural Modulus...

Last Answer : answer:Strength is how strong a material is – basically breaking load. Modulus is how flexible or stretchy a material is. Does not matter if the test coupon breaks or not. Think of uncooked spaghetti vs rubber band.

When I do the dishes, why do the plastics sometimes end up greasy?

Description : When I do the dishes, why do the plastics sometimes end up greasy?

Last Answer : answer:I've noticed that too, must have something to do with the grease sticking to the plastic more. I always use tons of soap and rinse really well as I also have a phobia about tasting soap. ... run it for the same reason and because somewhere, deep down, I think it is inferior to hand washing.

Which plastics can helium support?

Description : Which plastics can helium support?

Last Answer : Most if not all plastics are porous and Helium is a small molecule and will pass through the plastic over time. You could try sealing the sculpture with a sealer and that my help contain the ... their balloons to give them long float time of sometimes weeks with the Mylar balloons going even longer.

Why not get a small chipper and chip non-recyclable plastics into small pieces before dumping?

Description : Why not get a small chipper and chip non-recyclable plastics into small pieces before dumping?

Last Answer : Because a landfill full of sharp plastic shards is not good for the enviroment. Also given that it won't speed up the rate decomposition I think it isn't worth the effort. Add on ... overall it's probably worsefor the enviroment. It would be better to boycot companies that use plastic packaging.

Do you remember the many questions on safe/unsafe plastics for water bottles, food storage, Nalgene, etc?

Description : Do you remember the many questions on safe/unsafe plastics for water bottles, food storage, Nalgene, etc?

Last Answer : answer:Here's a summary; http://tinyurl.com/3jdkmj And one of many from ask-public: http://www.ask-public.com/disc/466/water-bottles-plastic-glass-stainless-steel-or/ Similar articles in all ... (the white waxy, shiny coating). Tomatoes and other acid foods may leach more severely. Buyer beware.

Should we start mining old landfill sites for plastics and other recyclable material?

Description : Should we start mining old landfill sites for plastics and other recyclable material?

Last Answer : I don’t see why not! I think it could be worth it. Then we wouldnt have to cut down as many trees to get new stuff. All the stuff at the dump is just going to sit there anyways.

what are extruded plastics

Description : what are extruded plastics

Last Answer : Need Answer

How can we reduce the use of plastics in our daily life?

Description : How can we reduce the use of plastics in our daily life?

Last Answer : Usage of plastics should be banned by the government. First and Foremost thing is the role of an individual in reducing the usage of plastics. People should carry a cloth bag while going to shops ... grocery shops, markets etc. Steel or glass containers should be used at homes for storing things.

Which of the following is a biodegradable waste? (1) Wool (2) Polythene bags (3) Plastics (4) Nylon

Description : Which of the following is a biodegradable waste? (1) Wool (2) Polythene bags (3) Plastics (4) Nylon

Last Answer : (1) Wool

'Corrosion-resistant material' and 'noncorrodible material' will include which of the following ____________. A. plastics B. silver C. copper-nickel D. all of the above

Description : 'Corrosion-resistant material' and 'noncorrodible material' will include which of the following ____________. A. plastics B. silver C. copper-nickel D. all of the above

Last Answer : Answer: D

The substances used in colour paints, fil- ters, plastics and other materials?

Description : The substances used in colour paints, fil- ters, plastics and other materials?

Last Answer : Pigments

Which type of plastics is used for mak- ing adhesives; button etc?

Description : Which type of plastics is used for mak- ing adhesives; button etc?

Last Answer : Urea formaldehyde

Plastics are generally?

Description : Plastics are generally?

Last Answer : Synthetic polymers

Bakelite (phenol-formaldehyde) resin cannot be used as (A) Decorative paint (B) Decorative laminates (C) Electrical insulation (D) Glass reinforced plastics

Description : Bakelite (phenol-formaldehyde) resin cannot be used as (A) Decorative paint (B) Decorative laminates (C) Electrical insulation (D) Glass reinforced plastics

Last Answer : (A) Decorative paint

Visco-elastic behaviour exhibited by plastics is a __________ like behaviour. (A) Solid (B) Liquid (C) Combination of solid & liquid (D) Neither solid nor liquid

Description : Visco-elastic behaviour exhibited by plastics is a __________ like behaviour. (A) Solid (B) Liquid (C) Combination of solid & liquid (D) Neither solid nor liquid

Last Answer : (C) Combination of solid & liquid

__________ moulding is used for shaping of thermosetting plastics exclusively. (A) Compression (B) Injection (C) Transfer (D) Extrusion

Description : __________ moulding is used for shaping of thermosetting plastics exclusively. (A) Compression (B) Injection (C) Transfer (D) Extrusion

Last Answer : (C) Transfer

Plasticisers are added to synthetic plastics to (A) Impart flexibility (B) Improve workability during fabrication(C) Develop new improved properties not present in the original resin(D) All (A), (B) and (C)

Description : Plasticisers are added to synthetic plastics to (A) Impart flexibility (B) Improve workability during fabrication (C) Develop new improved properties not present in the original resin (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Most of the plastics are safe to be used upto a maximum temperature of __________ °C. (A) 100 (B) 150 (C) 350 (D) 450

Description : Most of the plastics are safe to be used upto a maximum temperature of __________ °C. (A) 100 (B) 150 (C) 350 (D) 450

Last Answer : (B) 150

Molecular weights of plastics ranges from (A) 1000 to 5000 (B) 5000 to 1000 (C) 20000 to 25000 (D) 10 9 to 10

Description : Molecular weights of plastics ranges from (A) 1000 to 5000 (B) 5000 to 1000 (C) 20000 to 25000 (D) 10 9 to 10

Last Answer : (C) 20000 to 25000

Which of the following additives are added to plastics to make it impervious to X-rays? (A) Asbestos (B) Barium salt (C) Carborundum (D) Phthalic acid

Description : Which of the following additives are added to plastics to make it impervious to X-rays? (A) Asbestos (B) Barium salt (C) Carborundum (D) Phthalic acid

Last Answer : (B) Barium salt

The compound of chlorine used in the plastics?

Description : The compound of chlorine used in the plastics?

Last Answer : Polyvinyl chloride (PVC

Interchain forces are the weakest in case of (A) Plastics (B) Fibres (C) Elastomers (D) Both rubber & elastomers

Description : Interchain forces are the weakest in case of (A) Plastics (B) Fibres (C) Elastomers (D) Both rubber & elastomers

Last Answer : (D) Both rubber & elastomers

__________ moulding process cannot be used for thermoplastic plastics. (A) Compression (B) Extrusion (C) Injection (D) None of these

Description : __________ moulding process cannot be used for thermoplastic plastics. (A) Compression (B) Extrusion (C) Injection (D) None of these

Last Answer : (C) Injection

Which are plastics? Name their different types and processes by which they are manufactured. Discuss the impact of the use of plastics on the environment.

Description : Which are plastics? Name their different types and processes by which they are manufactured. Discuss the impact of the use of plastics on the environment.

Last Answer : What is plastic? Plastic is a common name for Polymers: materials made of long strings of carbon and other elements. Each unit in a string is called a monomer, and is a chemical usually ... or hardened by heat. Some typical thermosets are: * Bakelite * Epoxy * Melamine * Polyester * Polyurethane

Differentiate between any five of the following: a) Thermoplastics and thermosetting plastics b) Lunar eclipse and solar eclipse c) Asteroid and meteorite d) Renewable and non-renewable energy resources e) Endothermic and exothermic reactions f) Star and planet g) Nuclear fission and nuclear fusion

Description : Differentiate between any five of the following: a) Thermoplastics and thermosetting plastics b) Lunar eclipse and solar eclipse c) Asteroid and meteorite d) Renewable and non-renewable energy resources e) Endothermic and exothermic reactions f) Star and planet g) Nuclear fission and nuclear fusion

Last Answer : a) Thermoplastics and thermosetting plastics: Thermoplastics: Thermoplastics can be repeatedly softened by heating and hardened by cooling.Thermoplastic molecules, which are linear or slightly branched, do ... or explode in midair. Remains of meteoroids that reach the surface are called meteorites.

Visco-elastic behaviour of materials which is time dependent is common in (A) Plastics (B) Crystalline solid (C) Non-crystalline solids (D) Non-crystalline organic polymer

Description : Visco-elastic behaviour of materials which is time dependent is common in (A) Plastics (B) Crystalline solid (C) Non-crystalline solids (D) Non-crystalline organic polymer

Last Answer : (D) Non-crystalline organic polymer

Which of the following are conductors? a) Ceramics b) Plastics c) Mercury d) Rubber

Description : Which of the following are conductors? a) Ceramics b) Plastics c) Mercury d) Rubber

Last Answer : c) Mercury