Description : Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance
Last Answer : (A) Impact strength
Description : Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength
Last Answer : (C) Machinability
Description : Pick out the wrong statement. (A) Pure rubber is as useless as pure gold as a material of construction (B) Thermal conductivity of aluminium is higher than that of copper; henceit is ... has poor weldability (D) Reinforced plastics are made from both thermoplastic as well as thermosetting plastics
Last Answer : (B) Thermal conductivity of aluminium is higher than that of copper; henceit is increasingly used for utensil making
Description : On a cold day when the room temperature is 15°C, the metallic cap of a pen becomes much colder than its plastic body, though both are at the same temperature of 15°C, because - (1) metals ... metals (3) metals are good conductors of heat (4) plastics have a higher thermal conductivity than metals
Last Answer : (3) metals are good conductors of heat Explanation: On a chilly day, the room temperature is lower than our body temperature. Since metals have a higher coefficient of thermal conductivity than plastic, they ... from our fingers will flow to the metal cap much more quickly than to the plastic body.
Description : On a cold day when the room temperature is 15°C, the metallic cap of a pen becomes much colder than its plastic body, though both are at the same temperature of 15°C, because : (1) metals ... metals (3) metals are good conductors of heat (4) plastics have a higher thermal conductivity than metals
Last Answer : metals are good conductors of heat
Description : Addition of nickel to copper improves its (A) Machinability (B) Ductility (C) Strength (D) Hardness
Last Answer : (D) Hardness
Description : Lead is added to 60:40 brass primarily to improve (A) Machinability (B) Corrosion resistance (C) Fluidity (D) Strength
Last Answer : (A) Machinability
Description : Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working
Last Answer : Option B
Description : Which of the following is (are) true? (A) Cast iron has poor tensile strength compared to steel (B) Failure of cast iron flywheel is sudden and total (C) Machinability of cast iron flywheel is poor compared to steel flywheel (D) All of the above
Last Answer : (D) All of the above
Description : Define: i)Tensile strength ii) Machinability
Last Answer : i) Tensile strength: It is the ability or capacity of a metal to carry the load without breaking. Or A tensile strength of a metal is its ability to resist pull without breaking. ii) Machinability: ... can be easily cut by cutting tools to produce a desired shape & surface finish on its surface.
Description : Tempering of a material does not improve its (A) Machinability (B) Toughness (C) Internal stress level (D) Softness
Last Answer : A) Machinability
Description : Aluminium as a material of construction suffers from the disadvantage of (A) Very high cost (B) Rather low tensile strength (C) Very low strength to weight ratio (D) Scarce availability
Last Answer : (B) Rather low tensile strength
Description : Which of the following are problems with the current rapid prototyping and additivemanufacturing technologies? a.Limited material variety b.Inability to convert a solid part into layers c.Poor machinability of the starting material d.The inability of the designer to design the part
Last Answer : a.Limited material variety
Description : Pick up the non-inflammable plastic from the following: (A) Cellulose acetate plastics (B) Polyvinyl chloride plastics (C) Phenol formaldehyde plastic (D) Urea formaldehyde plastic
Last Answer : Answer: Option B
Description : I need ways to test/get data about homemade plastics. What can I do with Flexural Strength and Flexural Modulus...
Last Answer : answer:Strength is how strong a material is – basically breaking load. Modulus is how flexible or stretchy a material is. Does not matter if the test coupon breaks or not. Think of uncooked spaghetti vs rubber band.
Description : Plastics are (A) Good conductors of heat. (B) Good conductors of electricity. (C) Bad conductors of electricity. (D) High density.
Last Answer : (C) Bad conductors of electricity.
Description : Detrimental property of a material for shock load applications (a) High density (b) Low toughness (c) High strength (d) Low hardness
Last Answer : (b) Low toughness
Description : Creep is not exhibited at low temperature by (A) Rubber (B) Acrylics (C) Lead (D) Plastics
Last Answer : (C) Lead
Description : For handling sulphuric acid of 95% strength, the suitable material of construction for pipes is (A) Stainless steel (B) Cast iron (C) Aluminium (D) Nickel
Last Answer : (B) Cast iron
Description : The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength
Last Answer : (A) Resilience
Description : The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength
Description : . To improve the machinability of steel, it is generally subjected to (A) Spheroidising (B) Tempering (C) Normalising (D) Annealing
Last Answer : (A) Spheroidising
Description : To improve the machinability of steel by its softening, it is subjected to (A) Cold working (B) Annealing (C) Shot blasting (D) Heating
Last Answer : (B) Annealing
Description : Addition of __________ to steel does not help in improving its machinability. (A) Sulphur (B) Silicon (C) Lead (D) Phosphorous
Last Answer : (B) Silicon
Description : Machinability of hard alloys and tool steels is improved by (A) Spheroidising (B) Annealing (C) Tempering (D) Normalising
Description : o improve the machinability of steel, it is generally subjected to (A) Spheroidising (B) Tempering (C) Normalising (D) Annealing
Last Answer : Option A
Description : Pick out the wrong statement about the machinability of metals. Machinability of a metal (A) Decreases with increase in strain hardening tendencies (B) Decreases with increase in hardness, in general (C) Depend on the composition, microstructure and physical & mechanical
Last Answer : Option C
Description : The main drawback of centrifugal pump is a)necessity of priming b) discharge from pump varies with the load of water c) For high heads efficiency is low up to 50% d) the suction lift is limited to 6 metre e) all of the above*
Last Answer : e) all of the above*
Description : The most important drawback of sucralfate in the treatment of duodenal ulcer is: A. Low ulcer healing efficacy B. Poor relief of ulcer pain C. High incidence of side effects D. Need for taking a big tablet four times a day
Last Answer : D. Need for taking a big tablet four times a day
Description : Aluminium alloy is one of the most suitable materials of construction for aircrafts mainly due to its (A) High strength to weight ratio (B) Low temperature strength properties (C) Its ability ... rolled, forged & stamped (D) High strength and corrosion & oxidation-resistance at elevated temperature
Last Answer : (A) High strength to weight ratio
Description : While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation
Last Answer : A) Low impact strength
Description : Should we start mining old landfill sites for plastics and other recyclable material?
Last Answer : I don’t see why not! I think it could be worth it. Then we wouldnt have to cut down as many trees to get new stuff. All the stuff at the dump is just going to sit there anyways.
Description : 'Corrosion-resistant material' and 'noncorrodible material' will include which of the following ____________. A. plastics B. silver C. copper-nickel D. all of the above
Last Answer : Answer: D
Description : Flexible plastic pipes are made of (A) High density polyethylene (HDPE) (B) Low density polyethylene (LDPE) (C) Polypropylene (D) Unsaturated polyester
Last Answer : (B) Low density polyethylene (LDPE)
Description : Would a low-temp glue gun be better than a high-temp glue gun for plastics?
Last Answer : A low temperature glue gun would be best because there would be less damage to the plastic from the heated glue.
Description : Pick up the correct statement from the following: (A) Plastics have generally low melting point (B) The coefficient of thermal expansion of plastics is about three times than that of steel (C) ... fibre-glass with phenolic resins has absorption coefficient of about 0.67 (D) All the above
Last Answer : Answer: Option D
Description : The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength
Last Answer : b) Yield strength
Description : Define the terms: i) Hardness ii) Toughness iii) Brazing iv) Machinability
Last Answer : i) Hardness:- Hardness is the property of metal possessed by a material which enables it to resist penetration or abrasion or scratching by other material. Diamond is the hardest of known materials. ... can be easily cut by cutting tools to produce a desired shape & surface finish on its surface
Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace
Last Answer : (B) Enhanced sensible heat loss in the flue gas
Description : . Platinum catalyst used in the earlier days of sulphuric acid manufacture by contact process suffers from the drawback like (A) High cost (B) Fragile nature (C) Easy poisoning tendency (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Floppy disks which are made from flexible plastic material are also called? A) Hard disks B) High-density disks C) Diskettes D) Templates
Last Answer : Answer : C
Description : Floppy disks which are made from flexible plastic material are also called? a. Hard disks b. High-density disks c. Diskettes d. Templates
Last Answer : Diskettes
Last Answer : c. Diskettes
Description : Which of the following is the costliest material of construction used in pressure vessel construction? (A) Low alloy steel (B) Lead (C) Titanium (D) High alloy steel
Last Answer : (C) Titanium
Description : Pick up the correct statement from the following: (A) Permeability is a measure of conducting the magnetic lines of force in the material (B) Permeability is a measure of the extent to which magnetic ... magnetic flux density (B) to the field strength of the magnetizing field (D) All of these
Description : Bakelite (phenol-formaldehyde) resin cannot be used as (A) Decorative paint (B) Decorative laminates (C) Electrical insulation (D) Glass reinforced plastics
Last Answer : (A) Decorative paint
Description : Visco-elastic behaviour exhibited by plastics is a __________ like behaviour. (A) Solid (B) Liquid (C) Combination of solid & liquid (D) Neither solid nor liquid
Last Answer : (C) Combination of solid & liquid
Description : __________ moulding is used for shaping of thermosetting plastics exclusively. (A) Compression (B) Injection (C) Transfer (D) Extrusion
Last Answer : (C) Transfer