Enlist die accessories and state function of knock out

1 Answer

Answer :

Die Accessories are as follows:

1) Stops

a)Button stop

b) Lever stop

2) Pilot

a)Direct pilot

b)Indirect Pilot

3) Knock out

4) Strippers

a) Fixed stripper

b) Spring loaded strippers

5) Pressure Pad

Knock out: The function of knock out is to eject the finished components from the die cavity. 


Related questions

Description : State the functions of the following die accessories: pilots, stops, strippers, pressure pad. 

Last Answer : Answer: Functions of die accessories. 1. Pilots: The pilot positions, the stock strip accurately and bring it into proper position for blanking and piercing operations. They act as guides during the ... 4. Pressure pad: It is used for drawing operation for maintaining flat surface of the cup. 

Description : Describe briefly any two die accessories.

Last Answer : 1. Stops: The stops are used for correct spacing of the sheet metal as it is fed below the punch to give the greatest output in given length of the plate. 2. Pilots: The pilot ... 5. Pressure pad: It is used for drawing operation for maintaining flat surface of the cup   

Description : Name four die accessories and write their functions.

Last Answer : Die Accessories: 1) Stripper: To remove scrap material from the punch as it cleans the die block. 2) Pilots: The pilot positions, the stock strip accurately and bring it into proper position for ... . 6) Pressure Pad: It is used for drawing operation for maintaining flat surface of the cup. 

Description : Enlist any four operations carried out in forging process and explain fullering with neat sketch.

Last Answer : Operations carried out in forging process:  a) Upsetting b) Drawing Down c) Setting down d) Welding e) Bending f) Cutting g) Punching Fullering: In ... sledge hammer. The force is applied on the top fuller which results in decreasing the cross section at that point.

Description : Enlist any four forgeable materials.

Last Answer : Following are the forgeable materials; Forgeable Materials:  1) Aluminium alloys 2) Magnesium alloys 3) Copper alloys. 4) Carbon and low alloy steels 5) Martensitic stainless steels 6) ... ) Columbium alloys 10) Tantalum alloys 11) Molybdenum alloys 12) Tungsten alloys 13) Beryllium.

Description : Enlist press operations . Explain lancing and piercing. 

Last Answer : Press Operations: [1] Cutting or Shearing Operations: Blanking, Punching, Piercing, Notching, perforating, trimming, shaving, slitting, lancing. [2] Bending Operation: Angle bending [3] Forming ... clearance is provided on the die. Figure shows punch and die set for piercing. 

Description : Describe buffing process and enlist its any two applications.

Last Answer : Buffing process :- Buffing is used to give a much higher, lustrous, reflective finish that cannot be obtained by polishing. The buffing process consists in applying very fine abrasives with ... , tools, store fixtures, commercial and residential hardware and household utensils and appliances.

Description : Define soldering process and enlist any two applications.

Last Answer : Soldering: Soldering is a method of joining two or more piece of metal by means of a fusible alloy or metal, called solder, applied in the molten state. Applications: 1. Circuitry ... gutters, 9. Refrigeration and plumbing machine tools components, 10. Copper foil in stained glass work.

Description : Enlist any four pressing operations.

Last Answer : Pressing Operations are as follows: a) Blanking b) Punching c) Notching d) Perforating e) Trimming f) Shaving g) Slitting h) Lancing i) Bending j) Drawing k) Squeezing

Description : Enlist any four forging components.

Last Answer : Forging Components:  1. Connecting rod  2. Crankshaft  3. Camshaft  4. Alloy wheel  5. Drive shafts  6. Clutch hubs  7. Universal joints  8. Hand Tools

Description : Enlist any four merit and demerits of mechanical press

Last Answer : Merit :- 1. Machine structure is rational and small. 2. It is very easy to operate and it operate at a high utilization ratio. 3. Less cost of machine 4. Simple in construction. ... capacity. 3. Limited stroke length. 4. The force does not remain constant throughout the stroke.

Description : Enlist any four demerits of VMC 

Last Answer : 1) Need to knowledge of coding i.e difficult  2) need to proper skilled  workers 

Description : Enlist any four demerits of soldering

Last Answer : 1) Strength of soldered joint is low. 2) Soldered joint cannot be used in high temperature applications. 3) Limitation for joining large sections. 4) Careful removal of flux residual is required to prevent corrosion. 5) Flux may contain toxic components.

Description : Enlist names of any four parts of automobile that can be manufactured by forging.

Last Answer : Following are few automotive components that can be manufactured by forging Process: 1. Connecting rod 2. Crankshaft 3. Camshaft 4. Gears 5. Alloy wheel

Description : Enlist the different materials used in press work for automobile application. 

Last Answer : Answer: Materials used in press work  1) Aluminium, 2) copper, 3) brass, 4) mild steel, 5) Galvanized iron (G.I) sheets, 6) Duralumin, 7) Y-alloys, 8) naval brass, 9 ... ) Babbitt metal, 11) stainless steel & its alloys, 12) Different types of steels & its alloys.

Description : Enlist four press components used in automobiles. 

Last Answer : The various Pressed Products used in Automobiles are: 1) Gears 2) Crank Shafts 3) Automobile panels 4) Wires 5) Frames and Chassis 6) Connecting Rods 7) Springs 8) Carburetor bodies 9) Valves 10) Combustion Chamber 11) Cylinder heads & blocks 12) Gear box cases etc.

Description : State the function of pilot and stopper in a die.

Last Answer : Function of pilot and Stopper: Pilots: The pilot positions the stock strip accurately and bring it into proper position for blanking and piercing operations. They act as guides during the piercing or blanking ... it is fed below the punch to give the greatest output in given length of the plate. 

Description : State “Plane washer” making process with use of combination die.

Last Answer : (Note: The plain washers can be produced by using Compound die or Progressive die. It is not possible to use combination die for making plain washers, so consider compound die or progressive die for answer. ... Stop 2.sheet metal 3.pilot 4.blanking punch 5.ram 6.piercing punch 7.stripper 8.die

Description : Explain constructional features, and working of progressive die. Also state the functions of any four parts of progressive die. 

Last Answer : Constructional features and Working of Progressive Die:  A progressive die consists of the following parts. 1. Stop 2. Sheet metal 3. Pilot 4. Blanking punch 5. Ram 6. Piercing ... 7. Piercing punch: The function of piercing punch is to produce punched holes into the sheet metal. 

Description : Explain with sketch construction and application of progressive die.

Last Answer : OR Construction A progressive die consists of the following parts.: 1. Stop 2. Sheet metal 3. Pilot 4. Blanking punch 5. Ram 6. Piercing punch 7. Stripper Plate 8. Die ... such as automotive, electronics and appliances. Example car brake caliper, washer, lid of a beverage can etc.

Description : List the parts of standard die set.

Last Answer : 1)Die 2)Die Block 3)Lower Shoe 4)Punch 5)Upper Shoe  6)Back Up Plate 7)Stripper

Description : Difference between compound and combination die.

Last Answer : Compound die Combination die 1. Any two cutting operations can be performed at one station. 1. Both cutting and forming operations can be performed at one station. 2. Both operations performed in a ... operations performed. 5. e.g. washer 5. e.g. drawing cup shaped part.

Description : Draw a neat sketch of progressive die. 

Last Answer : progressive die

Description : Explain the importance of pressure pads in a die with neat sketch.

Last Answer : Importance of Pressure pad:  It is used for drawing operation for maintaining flat surface of the cup. A pressure pad presses against the material during L bending or U bending, and is used for ... . There is also the purpose of stripping off the material from the punch after forming.

Description : Explain simple die with neat sketch

Last Answer : Simple Die: Simple die or single action dies perform single operation for each stroke of the press slide. The operation may be cutting or forming operation such as blanking, punching, piercing etc. ... are simple in construction and can manufacture by conventional machining processes.    

Description : Explain closed die forging with neat sketch

Last Answer : Impression die & Closed die forging process: Closed Die forging is also known as impression die forging. Close die forging process consist of specially prepared dies to manufacturing forged parts in large ... of accuracy. Complex shaped parts can be easily forged by this forging process.  

Description : Draw neat sketch showing various parts of die set. 

Last Answer : Answer: 1. Stop 2.Sheet metal 3.Pilot 4.Blanking punch 5.Ram 6.Piercing punch 7.Stripper 8.die Fig. Progressive Die OR

Description : Draw neat sketch of compound die, showing various parts of it.

Last Answer : Answer:

Description : Differentiate between open die forging and close die forging.

Last Answer : Difference between open die and close die forging:

Description : (i) Compare Open Die Forging and Close Die Forging. (ii) Explain with neat sketch process of Drop Forging.

Last Answer : (i) Difference between Open Die and Close Die Forging: (ii)Drop Forging  Drop forging is carried out by using drop hammers. They are board or gravity hammer, air lift hammer and power drop ... of upper and lower dies. The ram is fastened to the lower end of vertical hard wood board.

Description : Sketch and explain a progressive die used to make washer.

Last Answer : Progressive Die: In a progressive die two or more operations are performed simultaneously at two or more stations with each press stroke by mounting separate sets of dies and punch. The metal is progressed ... locate it while the blanking punch descend and shear the plate to form a washer.  

Description : Explain construction and working of Combination Die with neat sketch.

Last Answer : Combination Die: In this both cutting and non-cutting operations are performed at one station of the press in every stroke of the ram. Figure shows a combination of blanking and drawing die.In this ... as blank holder when the drawing punch descends and draws the blank into the desired shape.

Description : State the function of G00, G94, M08 and M30 used in CNC part programming. 

Last Answer : 1) G00 :- Rapid Traverse Function G00 is the basic G-code for CNC programming to initiate rapid motion mode i.e used for quickly positioning the tool. G00 can be used where the tool is not ... production. As soon as the program ends he can place the next component and start the next cycle. 

Description : State function of preparatory and miscellaneous code with two examples each.

Last Answer : Function of Preparatory Code (G-Code): Preparatory functions are the G-codes that identify the type of activities the machine will execute. [1] A program block may contain one or more G-codes. [2 ... (CW) Rotation M06 Tool Change M08 Coolant On M09 Coolant Off M30 Program Stop and Tape Rewind

Description : State the function of „G‟ Codes and „M‟ codes with any two examples.

Last Answer : G Codes ( Preparatory Functions) The preparatory function instructs the machine tool to get prepared for the operation to follow, the preparatory function is represented by two digits preceded by letter G e.g. ... . i) M02 - Program end ii) M06 - Tool change iii) M08 - Coolant ON

Description : State the function of following codes: (1) G18, (2) G71, (3) M05, (4) M30

Last Answer : G18 – aligns the arc plane with the X and Z axes G71-Metric Input or input in mm, M05- Spindle stop M30-End of program & reset 

Description : State function of ATC in CNC machine.

Last Answer : An Automatic tool changer or ATC is used in computerized numerical control (CNC) machine tools to improve the production and tool carrying capacity of the machine. ATC changes the tool very quickly, reducing the non-productive time.

Description : State the function of the programming code. (i) G01 (ii) G90

Last Answer : (i) G01: Linear Interpolation. (ii) G90: Absolute Programming.

Description : Explain the shielded metal arc welding (SMAW) processes with neat sketch. State its two advantages and disadvantages.

Last Answer : Working  : Shielded metal arc welding uses a metallic consumable electrode of a proper composition for generating arc between itself and the parent work piece. The molten electrode metal fills the weld ... . 2. Weld may contain slag inclusions 3. Fumes make difficult the process control.

Description : Explain the resistance spot welding process with neat sketch. State its two advantage and disadvantage. 

Last Answer : Resistance Spot welding: Spot welding is employed to join overlapping strips, sheets or plates of metal at small areas .The pieces are assembled between two electrodes, which must possess high electrical & thermal ... for making the RSW a success. 4. The thick jobs are not easy to weld. 

Description : Draw flatter and Fuller. State its use in forging.

Last Answer : 1. Fuller: Use of Fuller: Fuller is a forging tool, used to spread the metal. The fuller is placed against the metal stock, and then either the fuller or the stock is struck ... are used to give smoothness and accuracy to articles which have already been shaped by fullers and swages. 

Description : State the meaning of G90, G91.

Last Answer : Meaning of following G-Codes: G90 :- Absolute Dimensioning G91:- Incremental Dimensioning

Description : What is interpolation? State its types. Explain linear interpolation with neat sketch

Last Answer : Definition : When the feed rates of individual axis are not constant and they vary continuously through the move it is called interpolation. Following are the types of interpolation: 1. G00- Rapid Traverse 2. ... to clear the job for loading /Unloading N9 M02 EOB  Programme End.  

Description : State salient features of CNC machines.

Last Answer : Salient Features of CNC machines .. 1. A part program can be fed to the controller unit through a keyboard. 2. The part program once entered can be used again and again. That is why ... control unit allows compensation for any changes in the dimensions of cutting tools caused due wear or otherwise. 

Description : Name the different types of presses used in industry. State the working principle of press. 

Last Answer : Types of presses used in industry: According to Source of power to ram: 1. Crank 2. Cam 3. Eccentric 4. Power screw 5. Rack and pinion 6. Toggle 7. ... ) hydraulic, mechanical, pneumatic and respectively working on principle of Pascal law, Mechanical Pressure and Pneumatic Pressure.

Description : State the factors on which weldability depends.

Last Answer : Factors on which weldability depends: 1. Material grade, material thickness, design, weld property requirement 2. Equipment type, edge preparation design 3. Tip / work piece distance, ... Cost of materials 15. Code or specification requirements 16. Mechanical properties desired in joints

Description : State any two advantages of forging process. 

Last Answer : Advantages of forging processes: 1) Complex shaped parts can be forged 2) Mass production with greater accuracy is achieved. 3) It is very easy to maintain close tolerances. 4) ... highly skilled operator. 6) Better reproducibility. 7) Machining is not necessary to obtain final shape 

Description : State canned cycle & subroutines.

Last Answer : Canned cycle (Fixed cycle): It is defined as a set of instructions, inbuilt or stored in the system memory, to perform a fixed sequence of operations. [1] It reduces programming time and ... also called as sub programs. [4] After completion of subroutine the control returns to main program. 

Description : State advantages of CNC over NC.

Last Answer : Advantages of CNC over NC 1. Complex machining operations can be easily done. 2. It requires less inspection. 3. It reduces scrap & waste. 4. It gives high production rate. 5. ... is available in CNC lathe which gives idea about job. This feature is not available in conventional machine 

Description : State blasting and tumbling.

Last Answer : 1. Blasting (Abrasive blast cleaning): This method is widely used for removing all classes of scale and rust from forgings, Castings, weld elements, and heat treated parts. Depending on the finish ... by friction a fine cutting action which removes fins, flashes, and scales from the products.