How to Clean an Oil Furnace Heat Exchanger?

How to Clean an Oil Furnace Heat Exchanger?
by

1 Answer

Answer :

If you have a heat exchanger within your oil furnace, you probably know that it is of vital importance that you must regularly clean out the buildup of soot inside of it. You should probably do this at least once every passing year. If you let too much soot sit in the furnace, it will probably raise the power bill significantly, it will significantly raise the risk of fire and it will also end up forcing carbon monoxide to enter the home, which has a reputation for being deadly. You should let a technician assist you in flame adjustments, much the majority of people and homeowners can easily clean out the soot that builds up within the heat exchanger.For this project, you are going to need the manual which came with your oil furnace, a small brush that has stiff feeling bristles, a flashli
by
selected by

Related questions

How to Clean Your Heat Exchanger Properly to Prolong It’s Life?

Description : How to Clean Your Heat Exchanger Properly to Prolong It’s Life?

Last Answer : Cleaning is oftentimes considered to be a tasking job which noone would want to be doing, but there are certain things that wecan never avoid. Cleaning does not only involve sweeping the floor,wiping ... ofpeople tend to forget and look over. As a result, a number ofaccidents have occurred which inv

Heat transfer efficiency leading of energy conservation in a heat exchanger can be achieved by (A) Keeping the heat transfer surface clean (B) Enhancing the fluid pumping rate (C) Increasing the tube length (D) None of these

Description : Heat transfer efficiency leading of energy conservation in a heat exchanger can be achieved by (A) Keeping the heat transfer surface clean (B) Enhancing the fluid pumping rate (C) Increasing the tube length (D) None of these

Last Answer : (A) Keeping the heat transfer surface clean

Which is the best tube arrangement (in a shell and tube heat exchanger) if the fluids are clean and non-fouling? (A) Square pitch (B) Triangular pitch (C) Diagonal square pitch

Description : Which is the best tube arrangement (in a shell and tube heat exchanger) if the fluids are clean and non-fouling? (A) Square pitch (B) Triangular pitch (C) Diagonal square pitch chemical-engineering

Last Answer : (B) Triangular pitch

Fouling factor for a heat exchanger is given by (where, U1 = heat transfer co-efficient of dirty surface U2 = heat transfer co-efficient of clean surface). (A) U1 - U2 (B) 1/U1 - 1/U2 (C) 1/U2 - 1/U1 (D) U2 - U1

Description : Fouling factor for a heat exchanger is given by (where, U1 = heat transfer co-efficient of dirty surface U2 = heat transfer co-efficient of clean surface). (A) U1 - U2 (B) 1/U1 - 1/U2 (C) 1/U2 - 1/U1 (D) U2 - U1

Last Answer : (B) 1/U1 - 1/U2

Hot water (0.01 m3 /min) enters the tube side of a counter current shell and tube heat exchanger at 80°C and leaves at 50°C. Cold oil (0.05 m3 /min) of density 800 kg/m3 and specific heat of 2 kJ/kg.K enters at 20°C. The log mean temperature difference in °C is approximately (A) 32 (B) 37 (C) 45 (D) 50

Description : Hot water (0.01 m3 /min) enters the tube side of a counter current shell and tube heat exchanger at 80°C and leaves at 50°C. Cold oil (0.05 m3 /min) of density 800 kg/m3 and specific heat of ... mean temperature difference in °C is approximately (A) 32 (B) 37 (C) 45 (D) 50

Last Answer : (A) 32

__________ heat exchanger is used for chilling oil to be dewaxed. (A) U-tube (B) Double pipe (C) Fixed tube

Description : __________ heat exchanger is used for chilling oil to be dewaxed. (A) U-tube (B) Double pipe (C) Fixed tube

Last Answer : (B) Double pipe

It's 10F out before windchill, and I have no heat, exactly how do I "clean" my furnace?

Description : It's 10F out before windchill, and I have no heat, exactly how do I "clean" my furnace?

Last Answer : If I were you I’d get into a nice zero degree sleeping bag and wait for help.

Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Description : Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Last Answer : (D) Both (A) and (B)

Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel, because its (A) Emissivity factor is higher (B) Sulphur content is lower (C) Flue gas has lower dew point thereby facilitating more waste heat recovery (D) All (A), (B) and (C)

Description : Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel, because its (A) Emissivity factor is higher (B) Sulphur content is lower (C) Flue gas has lower dew point thereby facilitating more waste heat recovery (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Maintain 850 OC for 1 hour (soaking time).  Cool the material to 60 OC in 4 hours. a) Calculate the efficiency of the furnace, if the specific heat of steel is 0.12 kcal/kgOC and fuel oil consumption per batch is 1400 litres.  GCV of fuel oil - 10200 kcal/kg,  Cost of fuel oil - Rs. 46,000/kL,  Sp. gr. of fuel oil - 0.92. b) Due to high cost of oil, the plant management decides to convert to a lower operating cost LPG fired furnace lined on the inside with ceramic fibre insulation and with an operating efficiency of 80%, for same requirement. The investment towards installation of the new furnace is Rs. 50 lakhs. Calculate the Return on Investment, if the plant operates two batches per day and 250 days in a year.  Cost of LPG - Rs. 75/kg,  GCV of LPG - 12500 kcal/kg.

Description : In a heat treatment shop, steel components are heat-treated in batches of 80 Tons. The  heat treatment cycle is as follows;  Increase temperature from 30 OC to 850 OC in 3 hours.  ... efficiency of 80%, for same requirement. The investment towards installation of  the new furnace is Rs. 50

Last Answer : Quantity of steel treated per batch - 80 Tons a. Efficiency of Furnace: Useful heat supplied to steel - 80000 x 0.12 x (850 - 30)   = 7872000 kcal/batch .1 mark Total heat ... = Rs. 64400/batch Efficiency of new LPG furnace - 80% Heat supplied in new LPG furnace - 7872000/0.8

Why the plate heat exchanger leaks?

Description : Why the plate heat exchanger leaks?

Last Answer : The common causes of a leak in your heat exchanger are: Improper tightening, incorrect plate installation, pressure surges from your pump, wrong gasket material selection and long periods of use in high pressure/temperature applications.

Heat Exchanger?

Description : Heat Exchanger?

Last Answer : Heat Exchanger - Use And PurposeA heat exchanger is significant in the process of transferringheat from one chamber to another or from one industrial process toa secondary process. Most heating units ... fluids that are flammable,toxic, dangerous and lethal to humans. This is the reason propermain

Heat Exchanger Types and Uses?

Description : Heat Exchanger Types and Uses?

Last Answer : A heat exchanger is a piece of industrial equipment thattransfers heat from one surface to another. It is used as a safetydevice that is meant to keep equipment from overheating tooquickly. Heat ... heatthrough conductive materials and expel it into the outside air,which cools the interior of the

What is a heat exchanger and what does it do?

Description : What is a heat exchanger and what does it do?

Last Answer : A heat exchanger is used to move heat from one place to another. What we call heat is actually energy. Hot things contain and emit more heat energy than cold things. A heat ... components of refrigeration systems, air conditioning systems, space heaters and a huge range of industrial systems.

Can a Dehumidifier be built into a heat exchanger unit?

Description : Can a Dehumidifier be built into a heat exchanger unit?

Last Answer : There are several dehumidifiers that can be integrated into a homes heating system.

Application of plate heat exchanger?

Description : Application of plate heat exchanger?

Last Answer : The plate heat exchanger is used in multiple systems in the field of HVAC, including geothermal water heating systems, instantaneous domestic hot water systems, semi-instantaneous domestic hot ... exchanger gradually replace the traditional container heating system, with a smaller area and more ec

_________ nuclear reactor does not require a heat exchanger tosupply steam to power turbine.(A) Molten sodium cooled(B) Helium cooled(C) Boiling water(D) Pressurised water

Description : _________ nuclear reactor does not require a heat exchanger tosupply steam to power turbine. (A) Molten sodium cooled (B) Helium cooled (C) Boiling water (D) Pressurised water

Last Answer : (C) Boiling water

Water is a better coolant than a gas (like CO2 , He, N2 etc.), because it (A) Is a better neutron moderator as well (B) Require comparatively smaller pumps and heat exchanger for a given heat transfer rate (C) Has a better heat transfer characteristics, and it can be pressurised to attain a high temperature (D) All (A), (B) and (C)

Description : Water is a better coolant than a gas (like CO2 , He, N2 etc.), because it (A) Is a better neutron moderator as well (B) Require comparatively smaller pumps and heat exchanger for a given heat transfer rate ... , and it can be pressurised to attain a high temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In a plate type heat exchanger, heat transfer plates are never made of (A) Stainless steel (B) Cast iron (C) Titanium (D) Hastelloy C

Description : In a plate type heat exchanger, heat transfer plates are never made of (A) Stainless steel (B) Cast iron (C) Titanium (D) Hastelloy C

Last Answer : (B) Cast iron

Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat exchanger, when the (A) Higher condensing film co-efficient is desired (B) Condensate is corrosive in nature (C) Lower pressure drop through the exchanger is desired (D) Temperature of the incoming vapor is very high Answer: Option B

Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high

Last Answer : (B) Supersaturated

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

In a 1-1 concurrent heat exchanger, if the tube side fluid outlet temperature is equal to the shell side fluid outlet temperature, then the LMTD is (A) ∞ (B) 0 (C) Equal to the difference between hot and cold fluids inlet temperature (D) Equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature

Description : In a 1-1 concurrent heat exchanger, if the tube side fluid outlet temperature is equal to the shell side fluid outlet temperature, then the LMTD is (A) ∞ (B) 0 ... temperature (D) Equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature

Last Answer : (B) 0

The equivalent diameter for the annulus of a double pipe heat exchanger, whose inner pipe has fins on the outside is __________ compared to the same size pipes without fins. (A) More (B) Less (C) Same (D) Unpredictable

Description : The equivalent diameter for the annulus of a double pipe heat exchanger, whose inner pipe has fins on the outside is __________ compared to the same size pipes without fins. (A) More (B) Less (C) Same (D) Unpredictable

Last Answer : (B) Less

. If all the conditions and dimensions are same, then the ratio of velocity through the tubes of a double pass heat exchanger to that through the single pass heat exchanger is (A) 1 (B) 2 (C) 1/2 (D) 4

Description : . If all the conditions and dimensions are same, then the ratio of velocity through the tubes of a double pass heat exchanger to that through the single pass heat exchanger is (A) 1 (B) 2 (C) 1/2 (D) 4

Last Answer : (B) 2

Fouling factor' used in the design of a multipass shell and tube heat exchanger is a (A) Non-dimensional factor (B) Factor of safety

Description : Fouling factor' used in the design of a multipass shell and tube heat exchanger is a (A) Non-dimensional factor (B) Factor of safety

Last Answer : (B) Factor of safety

. In a shell and tube heat exchanger, the tube side heat transfer co￾efficient just at the entrance of the tube is (A) Infinity (B) Zero (C) Same as average heat transfer co-efficient for tube side (D) None of these

Description : . In a shell and tube heat exchanger, the tube side heat transfer co￾efficient just at the entrance of the tube is (A) Infinity (B) Zero (C) Same as average heat transfer co-efficient for tube side (D) None of these

Last Answer : (A) Infinity

. If a single tube pass heat exchanger is converted to two pass, then for the same flow rate, the pressure drop per unit length in tube side will (A) Increase by 1.8 times (B) Decrease by 2 2 (C) Increase by 2 16 (D) Remain unchanged

Description : . If a single tube pass heat exchanger is converted to two pass, then for the same flow rate, the pressure drop per unit length in tube side will (A) Increase by 1.8 times (B) Decrease by 2 2 (C) Increase by 2 16 (D) Remain unchanged

Last Answer : (C) Increase by 2 16

A dephlegmator is a (A) Total condenser (B) Vacuum evaporator (C) Partial condenser (D) Double pipe heat exchanger

Description : A dephlegmator is a (A) Total condenser (B) Vacuum evaporator (C) Partial condenser (D) Double pipe heat exchanger

Last Answer : (C) Partial condenser

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

In case of a multipass shell and tube heat exchanger, providing a baffle on the shell side __________ the heat transfer rate. (A) Increases (B) Decreases (C) Does not affect (D) May increase or decrease, depends on the type of baffle

Description : In case of a multipass shell and tube heat exchanger, providing a baffle on the shell side __________ the heat transfer rate. (A) Increases (B) Decreases (C) Does not affect (D) May increase or decrease, depends on the type of baffle

Last Answer : (A) Increases

Pick out the wrong statement. (A) Heat transfer by radiation cannot occur across an absolute volume (B) In case of a shell and tube heat exchanger, the pressure drop through the shell is proportional to the number of times the fluid crosses the bundle between baffles (C) Propagation velocity for travel of heat radiation through vacuum is equal to the velocity of the light (D) The amount of heat involved in the condensation or vaporisation of 1 kg of a fluid is the same

Description : Pick out the wrong statement. (A) Heat transfer by radiation cannot occur across an absolute volume (B) In case of a shell and tube heat exchanger, the pressure drop through the shell is ... The amount of heat involved in the condensation or vaporisation of 1 kg of a fluid is the same

Last Answer : (A) Heat transfer by radiation cannot occur across an absolute volume

In a heat exchanger, floating head is provided to (A) Facilitate cleaning of the exchanger (B) Increase the heat transfer area (C) Relieve stresses caused by thermal expansion (D) Increase log mean temperature gradient

Description : In a heat exchanger, floating head is provided to (A) Facilitate cleaning of the exchanger (B) Increase the heat transfer area (C) Relieve stresses caused by thermal expansion (D) Increase log mean temperature gradient

Last Answer : (C) Relieve stresses caused by thermal expansion

__________ heat exchanger is the most suitable, when the temperature of shell side fluid is much higher than that of tube side. (A) Single pass, fixed tube sheet (B) U-tube (C) Three pass, fixed tube sheet (D) None of these

Description : __________ heat exchanger is the most suitable, when the temperature of shell side fluid is much higher than that of tube side. (A) Single pass, fixed tube sheet (B) U-tube (C) Three pass, fixed tube sheet (D) None of these

Last Answer : (B) U-tube

If the baffle spacing in a shell and tube heat exchanger increases, then the Reynolds number of the shell side fluid (A) Remains unchanged (B) Increases (C) Increases or decreases depending on number of shell passes (D) Decreases

Description : If the baffle spacing in a shell and tube heat exchanger increases, then the Reynolds number of the shell side fluid (A) Remains unchanged (B) Increases (C) Increases or decreases depending on number of shell passes (D) Decreases

Last Answer : (D) Decreases

Which type of heat exchanger is preferred for heavy heat loads? (A) Double pipe (B) Plate fine (C) Series and parallel set of shell and tube (D) None of these

Description : Which type of heat exchanger is preferred for heavy heat loads? (A) Double pipe (B) Plate fine (C) Series and parallel set of shell and tube (D) None of these

Last Answer : (C) Series and parallel set of shell and tube

The outlet temperature of cooling water in a heat exchanger is generally not allowed to exceed above 50°C in industrial practice mainly to avoid (A) Its evaporation loss (B) Excessive corrosion (C) Uneconomic LMTD (D) Decrease in heat exchanger efficiency

Description : The outlet temperature of cooling water in a heat exchanger is generally not allowed to exceed above 50°C in industrial practice mainly to avoid (A) Its evaporation loss (B) Excessive corrosion (C) Uneconomic LMTD (D) Decrease in heat exchanger efficiency

Last Answer : (B) Excessive corrosion

The purpose of floating head in a heat exchanger is to (A) Avoid buckling of tubes (B) Provide support for tubes (C) Decrease the pressure drop (D) Facilitate its lengthening, if needed

Description : The purpose of floating head in a heat exchanger is to (A) Avoid buckling of tubes (B) Provide support for tubes (C) Decrease the pressure drop (D) Facilitate its lengthening, if needed

Last Answer : (A) Avoid buckling of tubes

In a shell and tube heat exchanger, the height of 25 percent cut baffles is equal to (where, D = inside diameter of shell). (A) 0.25 D (B) 0.50 D (C) 0.75 D

Description : In a shell and tube heat exchanger, the height of 25 percent cut baffles is equal to (where, D = inside diameter of shell). (A) 0.25 D (B) 0.50 D (C) 0.75 D

Last Answer : (C) 0.75 D

In a multipass shell and tube heat exchanger, tube side return pressure loss is equal to __________ the velocity head. (A) Twice (B) Four times (C) Square root of (D) Square of

Description : In a multipass shell and tube heat exchanger, tube side return pressure loss is equal to __________ the velocity head. (A) Twice (B) Four times (C) Square root of (D) Square of

Last Answer : (B) Four times

A 2-4 heat exchanger involves (A) Only counter-flow of fluids (B) Only parallel-flow of fluids (C) Both counter and parallel-flow of the fluids (D) Smaller pressure drop compared to 1-2 exchanger

Description : A 2-4 heat exchanger involves (A) Only counter-flow of fluids (B) Only parallel-flow of fluids (C) Both counter and parallel-flow of the fluids (D) Smaller pressure drop compared to 1-2 exchanger

Last Answer : (C) Both counter and parallel-flow of the fluids

In a heat exchanger, one transfer unit means (A) A section of the exchanger in which change in temperature of one stream equals the average driving force in the section (B) The size of the exchanger in which heat transfer rate is 1 kcal/hr (C) Both (A) and (B) (D) None of these

Description : In a heat exchanger, one transfer unit means (A) A section of the exchanger in which change in temperature of one stream equals the average driving force in the section (B) The size of the exchanger in which heat transfer rate is 1 kcal/hr (C) Both (A) and (B) (D) None of these

Last Answer : (A) A section of the exchanger in which change in temperature of one stream equals the average driving force in the section

Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient for the cooling water, whether on shell side or tube side is the same. The best arrangement is (A) Vertical heat exchanger with steam on tube side (B) Vertical heat exchanger with steam on shell side (C) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Description : Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient ... ) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Last Answer : (B) Vertical heat exchanger with steam on shell side

LMTD correction factor which is to be applied for a cross-flow heat exchanger increases with increase in the number of shell passes. Its value for a single pass cross flow heat exchanger is (A) 0 (B) 1 (C) > 1 (D) < 1

Description : LMTD correction factor which is to be applied for a cross-flow heat exchanger increases with increase in the number of shell passes. Its value for a single pass cross flow heat exchanger is (A) 0 (B) 1 (C) > 1 (D) < 1

Last Answer : (D) < 1

In a parallel flow heat exchanger, if the outlet temperature of hot and cold fluids are the same, then the log mean temperature difference (LMTD) is (A) Minimum (B) Maximum (C) Zero (D) Infinity

Description : In a parallel flow heat exchanger, if the outlet temperature of hot and cold fluids are the same, then the log mean temperature difference (LMTD) is (A) Minimum (B) Maximum (C) Zero (D) Infinity

Last Answer : (C) Zero

Log mean temperature difference (LMTD) cannot be used, if (A) Heat transfer co-efficient over the entire heat exchanger is not constant (B) There exists an unsteady state (C) The heat capacity is not constant and there is a phase change (D) None of these

Description : Log mean temperature difference (LMTD) cannot be used, if (A) Heat transfer co-efficient over the entire heat exchanger is not constant (B) There exists an unsteady state (C) The heat capacity is not constant and there is a phase change (D) None of these

Last Answer : (D) None of these

For shell and tube heat exchanger, with increasing heat transfer area, the purchased cost per unit heat transfer area (A) Increases (B) Decreases (C) Remain constant (D) Passes through a maxima

Description : For shell and tube heat exchanger, with increasing heat transfer area, the purchased cost per unit heat transfer area (A) Increases (B) Decreases (C) Remain constant (D) Passes through a maxima

Last Answer : (D) Passes through a maxima

Air is best heated with steam in a heat exchanger of (A) Plate type (B) Double pipe type with fin on steam side (C) Double pipe type with fin on air side (D) Shell and tube type

Description : Air is best heated with steam in a heat exchanger of (A) Plate type (B) Double pipe type with fin on steam side (C) Double pipe type with fin on air side (D) Shell and tube type

Last Answer : (C) Double pipe type with fin on air side

Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a shell and tube heat exchanger (C) Steam jet ejector is used for vapor compression in a thermal recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Description : Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a ... recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Last Answer : (D) Heat sensitive materials should be concentrated in high pressure evaporators

The main function of baffles provided in a shell and tube heat exchanger is to (A) Facilitate the cleaning of outer tube surface (B) Enhance turbulence (C) Hold the tubes in position (D) All 'a', 'b' & 'c'

Description : The main function of baffles provided in a shell and tube heat exchanger is to (A) Facilitate the cleaning of outer tube surface (B) Enhance turbulence (C) Hold the tubes in position (D) All 'a', 'b' & 'c'

Last Answer : (B) Enhance turbulence

Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Description : Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Last Answer : (C) Increase the shell side heat transfer co-efficient