Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel, because its (A) Emissivity factor is higher (B) Sulphur content is lower (C) Flue gas has lower dew point thereby facilitating more waste heat recovery (D) All (A), (B) and (C)

Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel,
because its
(A) Emissivity factor is higher
(B) Sulphur content is lower
(C) Flue gas has lower dew point thereby facilitating more waste heat
recovery
(D) All (A), (B) and (C)
by

1 Answer

Answer :

(D) All (A), (B) and (C)
by

Related questions

Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Description : Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Last Answer : (D) Both (A) and (B)

Which of the following is not a by-product recovered in a high temperature coal carbonisation plant? (A) Benzol (B) Pitch-creosote mixture (PCM) (C) Naphthalene (D) Ethylene

Description : Which of the following is not a by-product recovered in a high temperature coal carbonisation plant? (A) Benzol (B) Pitch-creosote mixture (PCM) (C) Naphthalene (D) Ethylene

Last Answer : (D) Ethylene

Calorific value of pitch creosote mixture (PCM) i.e., C.T.F.-200 is about (A) 8800 kcal/m3 (B) 8800 kcal/kg (C) Same as that of coal middling (D) 25000 kcal/kg

Description : Calorific value of pitch creosote mixture (PCM) i.e., C.T.F.-200 is about (A) 8800 kcal/m3 (B) 8800 kcal/kg (C) Same as that of coal middling (D) 25000 kcal/kg

Last Answer : (B) 8800 kcal/kg

Optimum preheating temperature for pitch creosote mixture (PCM) which is also termed as C.T.F-200, before atomisation through burners is (A) 200 °F (B) 200 °C (C) 200 °K (D) 200 °R

Description : Optimum preheating temperature for pitch creosote mixture (PCM) which is also termed as C.T.F-200, before atomisation through burners is (A) 200 °F (B) 200 °C (C) 200 °K (D) 200 °R

Last Answer : (A) 200 °F

Incomplete combustion of fuel in the furnace is judged by high __________ of the flue gases. (A) CO content (B) Dew point (C) CO2 content (D) O2 content

Description : Incomplete combustion of fuel in the furnace is judged by high __________ of the flue gases. (A) CO content (B) Dew point (C) CO2 content (D) O2 content

Last Answer : (A) CO content

Coal tar fuel - 200 (CTF 200) is a mixture of (A) Pitch and creosote oil (B) Light oil and pitch (C) Anthracene and crecosote oil (D) Solar oil and pitch

Description : Coal tar fuel - 200 (CTF 200) is a mixture of (A) Pitch and creosote oil (B) Light oil and pitch (C) Anthracene and crecosote oil (D) Solar oil and pitch

Last Answer : (A) Pitch and creosote oil

High sulphur content in a fuel __________ of the flue gases. (A) Decreases the dew point (B) Increases the dew point (C) Reduces the combustion efficiency by limiting the permissible temperature reduction (D) Both (B) and (C)

Description : High sulphur content in a fuel __________ of the flue gases. (A) Decreases the dew point (B) Increases the dew point (C) Reduces the combustion efficiency by limiting the permissible temperature reduction (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Heat transfer rate to the stock/charge in the furnace does not depend upon the(A) Emissivity of the refractory walls(B) Size of the furnace(C) Use of waste heat recovery equipments(D) Thickness of the stock

Description : Heat transfer rate to the stock/charge in the furnace does not depend upon the (A) Emissivity of the refractory walls (B) Size of the furnace (C) Use of waste heat recovery equipments (D) Thickness of the stock

Last Answer : (C) Use of waste heat recovery equipments

Thermal efficiency of furnaces can be improved by (A) Waste heat recovery from flue gas (B) Minimising heat losses from furnace walls(C) Maintaining proper draught(D) All (A), (B) and (C

Description : Thermal efficiency of furnaces can be improved by (A) Waste heat recovery from flue gas (B) Minimising heat losses from furnace walls (C) Maintaining proper draught (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250

Description : Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250

Last Answer : (B) 750

Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Description : Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Last Answer : (B) 130

Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock

Description : Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock

Last Answer : (A) Type of fuels viz. solid, liquid or gaseous

Which of the following is not a continuous waste heat recovery equipment from the flue gases going out of furnace? (A) Economiser (B) Regenerator (C) Ceramic recuperator (D) Waste heat boiler

Description : Which of the following is not a continuous waste heat recovery equipment from the flue gases going out of furnace? (A) Economiser (B) Regenerator (C) Ceramic recuperator (D) Waste heat boiler

Last Answer : (B) Regenerator

In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & structural materials of furnace (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Description : In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & ... (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

White flue gas (resembling steam) coming out of the chimney of a thermal power plant indicates that the fuel used in the boiler furnace is (A) Tar (B) Coke oven gas (C) Pitch (D) Pulverised coke

Description : White flue gas (resembling steam) coming out of the chimney of a thermal power plant indicates that the fuel used in the boiler furnace is (A) Tar (B) Coke oven gas (C) Pitch (D) Pulverised coke

Last Answer : (B) Coke oven gas

LSHS is a type of furnace oil, which (A) Is more viscous than high viscosity furnace oil (HVFO) (B) Stands for low sulphur heavy stock (C) Is an ideal fuel for metallurgical furnaces due to its lower sulphur content (< 1%(D) All (A), (B) and (C))

Description : LSHS is a type of furnace oil, which (A) Is more viscous than high viscosity furnace oil (HVFO) (B) Stands for low sulphur heavy stock (C) Is an ideal fuel for metallurgical furnaces due to its lower sulphur content (< 1%) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat of the substance): 0.20 kCal/kg oC DT (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Description : Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat ... (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Last Answer : 21600

Pitch (a product of coal tar distillation) is always mixed with creosote oil, when it is to be burnt in a burner, because (A) Its calorific value is very less (B) Tar neutralises the residual acids present in pitch (C) It reduces viscosity and imparts fluidity for its transportation through pipelines at economic pressure drop (D) All (A), (B) and (C)

Description : Pitch (a product of coal tar distillation) is always mixed with creosote oil, when it is to be burnt in a burner, because (A) Its calorific value is very less (B) Tar neutralises the residual acids ... for its transportation through pipelines at economic pressure drop (D) All (A), (B) and (C)

Last Answer : (C) It reduces viscosity and imparts fluidity for its transportation through pipelines at economic pressure drop

In which of the waste heat recovery equipment, the flow of flue gas and air is alternately reversed after a fixed interval of time? (A) Recuperator (B) Regenerator (C) Waste heat boiler (D) None of these

Description : In which of the waste heat recovery equipment, the flow of flue gas and air is alternately reversed after a fixed interval of time? (A) Recuperator (B) Regenerator (C) Waste heat boiler (D) None of these

Last Answer : (B) Regenerator

To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Description : To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Find false statement about effect of sulphur in fuel? (A) It has heating value (B) It helps in electrostatic precipitation of ash in flue gases (C) It leads to corrosion of air heaters, ducting, etc. if flue gas exit temperature is low (D) It erodes furnace walls

Description : Find false statement about effect of sulphur in fuel? (A) It has heating value (B) It helps in electrostatic precipitation of ash in flue gases (C) It leads to corrosion of air heaters, ducting, etc. if flue gas exit temperature is low (D) It erodes furnace walls

Last Answer : (D) It erodes furnace walls

Which of the following is not an additive for flue gases from furnace to reduce its dew-point? (A) Ammonia (B) Fine dolomite (C) Alkaline powders (D) None of these

Description : Which of the following is not an additive for flue gases from furnace to reduce its dew-point? (A) Ammonia (B) Fine dolomite (C) Alkaline powders (D) None of these

Last Answer : (D) None of these

Which of the following is not an important property of fuel oil/furnace oil? (A) Sulphur content (B) Viscosity (C) Aniline point (D) Flash point

Description : Which of the following is not an important property of fuel oil/furnace oil? (A) Sulphur content (B) Viscosity (C) Aniline point (D) Flash point

Last Answer : (C) Aniline point

Catalytic cracking compared to thermal cracking of residue of vacuum distillation of crude oil (A) Gives higher yield of petrol (B) Lower octane number of petrol (C) Higher sulphur content in the product (D) Higher gum forming material in petro

Description : Catalytic cracking compared to thermal cracking of residue of vacuum distillation of crude oil (A) Gives higher yield of petrol (B) Lower octane number of petrol (C) Higher sulphur content in the product (D) Higher gum forming material in petro

Last Answer : (A) Gives higher yield of petrol

Crude oil is subjected to vacuum distillation in the last stage, because (A) High boiling point products like heavy fuel oil & lubricating oils are heat sensitive and may decompose (B) Lighter/low boiling products are prone to thermal decomposition (C) High purity products can be obtained thereby (D) None of these

Description : Crude oil is subjected to vacuum distillation in the last stage, because (A) High boiling point products like heavy fuel oil & lubricating oils are heat sensitive and may decompose (B) Lighter/low ... prone to thermal decomposition (C) High purity products can be obtained thereby (D) None of these

Last Answer : (A) High boiling point products like heavy fuel oil & lubricating oils are heat sensitive and may decompose

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

A liquid/gaseous fuel containing hydrocarbons and high amount of sulphur is burnt with 40% excess air. The flue gas still contains large amount of carbon monoxide. This may be due to the (A) Presence of large quantity of hydrogen in the fuel (B) Low calorific value of the fuel (C) High sulphur content in the fuel (D) Lack of thorough mixing of fuel with air

Description : A liquid/gaseous fuel containing hydrocarbons and high amount of sulphur is burnt with 40% excess air. The flue gas still contains large amount of carbon monoxide. This may be due to the (A) Presence of large ... fuel (C) High sulphur content in the fuel (D) Lack of thorough mixing of fuel with air

Last Answer : (D) Lack of thorough mixing of fuel with air

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

With increase in C/H ratio of a fuel, the dew point of flue gases (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease; depends on the type of fuel

Description : With increase in C/H ratio of a fuel, the dew point of flue gases (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease; depends on the type of fuel

Last Answer : (B) Decreases

Which among the following has the highest flue gas loss on combustion due to Hydrogen in the fuel? a) natural gas b) furnace oil c) coal d) light diesel oil

Description : Which among the following has the highest flue gas loss on combustion due to Hydrogen in the fuel? a) natural gas b) furnace oil c) coal d) light diesel oil

Last Answer : a) natural gas

Out of the following fuels, the difference between the net and gross calorific value is maximum in case of (A) Pitch (B) Fuel oil (C) Blast furnace gas (D) Bituminous coal

Description : Out of the following fuels, the difference between the net and gross calorific value is maximum in case of (A) Pitch (B) Fuel oil (C) Blast furnace gas (D) Bituminous coal

Last Answer : (B) Fuel oil

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Description : Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Design of waste heat boiler for recovery of waste heat from furnace gases depends upon the(A) Quantity & temperature of waste gas(B) Dust concentration & nature of dust in waste gas(C) Corrosive nature of the waste gas(D) All (A), (B) and (C)

Description : Design of waste heat boiler for recovery of waste heat from furnace gases depends upon the (A) Quantity & temperature of waste gas (B) Dust concentration & nature of dust in waste gas (C) Corrosive nature of the waste gas (D) All (A), (B) and (C)

Last Answer : (B) Dust concentration & nature of dust in waste gas

In a shell and tube heat exchanger, square pitch compared to triangular pitch (A) Gives a higher shell side pressure drop (B) Gives a lower shell side pressure drop (C) Can pack more surface area into a shell of given diameter (D) None of these

Description : In a shell and tube heat exchanger, square pitch compared to triangular pitch (A) Gives a higher shell side pressure drop (B) Gives a lower shell side pressure drop (C) Can pack more surface area into a shell of given diameter (D) None of these

Last Answer : (A) Gives a higher shell side pressure drop

Limestone powder is injected during pulverised coal burning in boilers to __________ the flue gases. (A) Reduce SO2 content in (B) Catalytically convert SO2 to SO3 in (C) Increase the dew point of (D) None of these

Description : Limestone powder is injected during pulverised coal burning in boilers to __________ the flue gases. (A) Reduce SO2 content in (B) Catalytically convert SO2 to SO3 in (C) Increase the dew point of (D) None of these

Last Answer : (A) Reduce SO2 content in

Oxygen trim control strategy __ a. continuously measures the oxygen content in the flue gas b. adjusts the combustion air flow c. Continually tuning the air-fuel mixture. d. All of above

Description : Oxygen trim control strategy __ a. continuously measures the oxygen content in the flue gas b. adjusts the combustion air flow c. Continually tuning the air-fuel mixture. d. All of above

Last Answer : d. All of above

Coal tar fuels (CTF) as compared to petroleum based fuel oils have higher (A) Calorific value (B) Higher C/H ratio (C) Sulphur content (D) Difference in gross & net calorific value

Description : Coal tar fuels (CTF) as compared to petroleum based fuel oils have higher (A) Calorific value (B) Higher C/H ratio (C) Sulphur content (D) Difference in gross & net calorific value

Last Answer : (B) Higher C/H ratio

A waste heat recovery system in industrial process has been key to reduce ....... Consumption. a) Coal b) Fuel c) Biogas d) Oil

Description : A waste heat recovery system in industrial process has been key to reduce ....... Consumption. a) Coal b) Fuel c) Biogas d) Oil

Last Answer : Fuel

Which of the following fuels is generally not used in thermal power plant boiler firing? (A) Furnace oil, light diesel oil and tar/PCM (B) Pulverised coking coal (C) Coal middling from washeries (D) B.F. gas, coke oven gas and L.D. converter gas

Description : Which of the following fuels is generally not used in thermal power plant boiler firing? (A) Furnace oil, light diesel oil and tar/PCM (B) Pulverised coking coal (C) Coal middling from washeries (D) B.F. gas, coke oven gas and L.D. converter gas

Last Answer : (B) Pulverised coking coal

Regenerators are used for waste heat recovery in (A) By-product coke ovens (B) Beehive coke oven (C) Blast furnace stoves (D) Soaking pits

Description : Regenerators are used for waste heat recovery in (A) By-product coke ovens (B) Beehive coke oven (C) Blast furnace stoves (D) Soaking pits

Last Answer : (A) By-product coke ovens

Oxygen percentage in the flue gas coming out of a gaseous fuel fired furnace should be ideally about __________ percent. (A) < 2 (B) < 5 (C) < 8 (D) < 10

Description : Oxygen percentage in the flue gas coming out of a gaseous fuel fired furnace should be ideally about __________ percent. (A) < 2 (B) < 5 (C) < 8 (D) < 10

Last Answer : (A) < 2

Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Description : Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

An indication of sensible heat content in air-water vapour mixture is a) wet bulb temperature b) dew point temperature c) density of air d) dry bulb temperature

Description : An indication of sensible heat content in air-water vapour mixture is a) wet bulb temperature b) dew point temperature c) density of air d) dry bulb temperature

Last Answer : d) dry bulb temperature

Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Description : Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Last Answer : (D) Lower theoretical flame temperature

Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of(A) Furnace oil with air(B) Furnace oil with oxygen(C) Blast furnace gas with air(D) Blast furnace gas with oxygen

Description : Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of (A) Furnace oil with air (B) Furnace oil with oxygen (C) Blast furnace gas with air (D) Blast furnace gas with oxygen

Last Answer : (C) Blast furnace gas with air

Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor

Description : Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor

Last Answer : compressor

Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Description : Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Last Answer : Billet Reheating Furnace