# Draw a neat sketch of simple curve showing all elements.

Draw a neat sketch of simple curve showing all elements.

Simple curve

## Related questions

Description : Draw neat sketch of simple circular curve and show notation there on.

Last Answer : Sketch of simple circular curve and show notation there on :

Description : Draw neat sketch of contour for the following i)Hill ii) Valley iii)Gentle Slope iv) Ridge Line

Last Answer : i)Hill ii) Valley iii)Gentle Slope iv) Ridge Line

Description : sketch of simple circular curve and show notation there on

Last Answer : Let the distance between P and Q be D' which is to be measured. A wave transmitted from the transmitter at station P' with certain phase angle. There is a ... phase angle. For finding the distance, the phase difference between transmitted wave is measured and converted into distance.

Description : Describe the method of setting out simple curve by using the method of offset from long chord with sketch.

Last Answer : Given data: Direction of two straights, chainage of point of intersection, radius of curve. Procedure:  1) Set theodolite over B and measure deflection angle Ф  2) Calculate tangent length by ... equal to tangent length.  4) Divide long chord into even number of equal parts.

Description : Explain the principle of techeometry with the help of a neat sketch.

Last Answer : Principle of tacheometry is based on principle of similar triangle in which corresponding sides & altitudes are proportional The ratio of distance of base from apex and length of base is always constant. ... S3=f/i=Constant Where f=focal length of objective and i =stadia intercept

Description : Explain the working principal of EDM with a neat sketch.

Last Answer : Let the distance between P and Q be D' which is to be measured. A wave is transmitted from the transmitter at station P' with certain phase angle. . There ... finding the distance, the phase difference between transmitted wave and reflected wave is measured and converted into distance.

Description : In a contour map, if contours are crossing each other, what will be nature of topography? Draw the sketch to support your answer.

Last Answer : If contours are crossing or intersecting each other, then there is overhanging cliff as shown in figure 1 below.

Description : Draw neat sketch showing various parts of die set.

Last Answer : Answer: 1. Stop 2.Sheet metal 3.Pilot 4.Blanking punch 5.Ram 6.Piercing punch 7.Stripper 8.die Fig. Progressive Die OR

Description : Draw neat sketch of compound die, showing various parts of it.

Description : Draw a neat sketch showing RCC components of lintel with 1:20 scale.

Last Answer : Draw a neat sketch showing RCC components of lintel with 1:20 scale.

Description : Draw a neat labelled sketch of a plan of bridge showing all its components

Last Answer : a plan of bridge

Description : What are the different methods of contouring? Describe any one method along with sketch . Also write the situation where it is suitable

Last Answer : There are two methods of contouring:- 1. Direct Method 2. Indirect Method - a. By squares  b. By cross section  c. By tacheometric Direct method of contouring - In this ... joining these identical coloured pegs, we get the required contours on ground by this direct method of contouring.

Description : Define tacheometry. State the principle of tacheometry with sketch.

Last Answer : Tacheometry : It is the branch of angular surveying in which horizontal and vertical distances are determined from instrumental observations only, is known as tacheometry. Principle of tacheometry : ... to corresponding staff intercept remains constant as shown below in figure 3

Description : Define grade contour. Give the procedure to locate grade contour on contour map with suitable sketch.

Last Answer : Grade Contour - It is the contour established on a specific grade or gradient along the hill side. OR   The line joining the points of equal grade or gradient is termed as grade contour.  ... all the marked points will give us the required grade contour of 1 in 30 accurately.

Description : State the principle of EDM with sketch.

Last Answer : Principle of EDM:- The fig shows a survey line AB, the length D of which is to be measured using EDM equipment placed at ends A. Let a transmitter be placed at A to propagate electromagnetic waves towards B ... measured at A. This will require EDM timing devices with an accuracy of 1 10-9s.

Description : Give classification of curve and explain any one in detail.

Last Answer : Types of curve : The curve is classified broadly in two categories 1. Horizontal curve - When the points of curve are joined in horizontal plane then it is known as horizontal curve. 2. Vertical ... roadway or railway tracks. Vertical curves are of four types. a) Summit curve b) Valley curve

Description : Give the classification of curve and Define 1.Transition curve 2. Reverse curve

Last Answer : Classification of curve is as follows1) Horizontal curve  a) Simple curve  b) Compound curve  c) Reverse curve  d) Transition curve  e) Lemniscate curve 2) Vertical curve  a) Summit curve ... their centers lie on opposites sides of the curve . They have one common tangent.

Description : State the meaning of degree of curve and long chord.

Last Answer : Degree of curve : The angle subtended at the centre by a standard chord of 30 m length, is known as degree of curve. Long Chord : The straight line joining rear tangent point and forward tangent point is called as long chord of curve.

Description : Explain the setting of curve by Rankine’s deflection angle method.

Last Answer : Rankine's deflection angle Method:-  1) Set up theodolite at first tangent point, T1 and level it carefully, set the vernier A to 3600 2) bisect the ranging rod at the point of ... . The angle thus obtained will be set on the vernier of the theodolite for setting out the curve.

Description : What is the degree of curve? Derive the relationship between radius and degree of curve.

Last Answer : Degree of curve The degree of the curve is the angle subtended at the center by a standard chord of 30 m length. Relationship between radius and degree of curve. Referring Fig Let R = the radius of the curve in m. D ... OM = R, PM = ½ MN = 15 m. Then sin D/2 = PM/OM = 15/R

Description : Explain the procedure of curve setting by method of offsets from long chord

Last Answer : Procedure: 1. Divide the long chord into an even number of equal parts say 8,10,12 etc. 2. Set out the offset as calculated from the formula  and obtain the required points on the ... ED, the offset for the right half of the curve will be the same as those on the left half side.

Description : Define compound curve and reverse curve

Last Answer : Compound Curve: A compound curve consists of two arc of different radius curving in the same direction. The centers of the two arc situated on the same side of the curve. Reverse Curve: A ... opposite direction with a common tangent. The two centers are on the opposite sides of a common tangent.

Description : Derive the relationship between the radius and degree of curve.

Last Answer : Relationship between radius and degree of curve. Referring Fig Let R = the radius of the curve in m. D = the degree of cuve.— MN = the chord 30 m long. P = Mid point of chord MN In triangle OMP, OM = R, PM = ½ MN = 15 m. Then sin D/2 = PM/OM = 15/R

Description : Define degree of curve.

Last Answer : The angle subtended at the centre of the circle by a chord of standard length of 30m is known as degree of curve.

Description : Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging. [2] After preliminary roll forging, ... Then the finished part is then trimmed in blanking die to remove excess metal or flash.

Description : Draw a neat sketch of Gating system. State the functions of any four elements.

Last Answer : Gating system:  1. Sprue: The circular cross section that minimizes heat loss and turbulence is sprue, and the area of it is quantified from the choke area as well as the gating ratio.  2. ... the molten metal flow from the ingate has to be proportional to the casting area's volume.

Description : Write the procedure of construction of WBM road with neat sketch showing various components

Last Answer : Construction Procedure:  a) Preparation of Foundation: The foundation for receiving the layer of WBM may be either the sub-grade or sub-base or base course. The depressions and pot holes on the existing road ... water and rolled. No traffic is allowed till WBM layer sets and dries out.

Description : Write four requirements of good formwork and draw a sketch showing cross section of formwork for a L-shaped column.

Last Answer : i. It should be strong enough to resist the weight of concrete, workers and machinery. ii. It should be economical compared to total cost of construction. iii. It should be possible to use the ... available. vii. It should be rigid enough to retain its shape without deflection or bulging.

Description : Draw a neat labelled diagram showing steam distillation at laboratory scale

Last Answer : labelled diagram showing steam distillation at laboratory scale

Description : Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Last Answer : Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Description : Draw neat sketches of: (i) Conventional bricks and (ii) Standard bricks showing all the dimensions

Last Answer : i) Conventional brick.   ii) Standard brick.

Description : Draw neat labeled diagram of single phase AC locomotive showing its various equipments of power circuit and give function of each equipment used in power circuit.

Last Answer : Functions of equipment: 1) circuit breaker: disconnects the locomotive equipment from the supply in the event of fault in the equipment / loco. 2) On load tap changer, used to control the ... 6) Traction motor: operates as per the required operating characteristics to take on the traction load.

Description : Explain the types of hill road curve with neat sketch.

Last Answer : Types of curves provided on hill road are as follow:  (1) Hair pin bend curve: The curve in a hill road which changes its direction through an angle of 180o or so, down the hill on the ... moving traffic. At such curves, the parapet wall is provided only for safety of fast moving traffic.

Description : Explain with neat sketch particle size distribution curve.

Last Answer : Particle size distribution curve (PSDC) is the semi log graph drawn as sieve size versus % finer of given soil sample. The PSDC is useful for grading of soil i.e. classification of ... : When graph is of wavy nature indicating particles of only specific size and deficiency of other sizes.

Description : Demonstrate the utility of Remote Sensing and GIS applications in Civil Engineering with appropriate examples.

Last Answer : Applications of Remote Sensing in Civil Engineering 1) Silting of storage reservoirs harbors etc. - Remote sensing technique that makes use of satellite imagery gives idea about the silting of ... Impact studies 6) Natural Hazard mapping or assessment 7) Water Resources availability.

Description : Apply knowledge of total station to prepare a contour map by describing its procedure.

Last Answer : Procedure of preparing contour map using total station1) Preliminary set up - Fix the total station over a station and level it. Press the power button to switch on the instrument. ... computer in the appropriate format. 8) Using appropriate application software, contour map will be prepared.

Description : Describe stepwise procedure to prepare the layout of a small building using total station.

Last Answer : Layout of small building by using total station: 1. On the plan supplied by an architect, number the column serially from left to right and top to bottom starting from top left ... of setting out by comparing the diagonal distance between the extreme column centres to their calculated values.

Description : Compare radiation and intersection methods of plane table surveying on any two parameters.

Last Answer : Radiation method Intersection method 1. It requires the plane table to occupy a single station.  1. This method requires setting the table up at minimum of two stations.  ... for locating inaccessible points by the intersection of the rays drawn from two instruments stations.

Description : Describe the procedure to determine co-ordinates of a station using GPS.

Last Answer : The following are some general GPS field survey procedures that should be performed at each station, observation, and/or session on a GPS survey. A. Receiver setup : GPS receiver shall be set up ... is to identify any problem that may exist which can be corrected before returning from the field.

Description : Explain the temporary adjustment of theodolite.

Last Answer : Temporary Adjustments: The temporary adjustments have to be carried out at every setup of the instrument before taking observations with the theodolite A)Setting up: 1) Place the instrument ... . The parallax can be removed by the sharp focusing until the image appears sharp and clear.

Description : Describe any one method of orientation of plane table surveying

Last Answer : Orientation by back sighting method: This method is accurate and is always preferred. Procedure: 1.Suppose A and B are two stations.The plane table is set up over A. The table is leveled by spirit level ... are perfect and needle is exactly at 0-0 , the orientation is said to be perfect.

Description : Name two software for GPS.

Last Answer : Softwares for GPS 1).GPSWOX 2) iGO 3) HERE 4)Navigon 5)Navman 6)EasyGPS 7) Caliper

Description : List two uses of EDM.

Last Answer : 1.It is useful for measuring the distances that are difficult to access. 2. It is useful in topographical survey. 3.Measurement of base line in triangulation survey can be carried out speedily and ... construction of gravity dams. 5.It is useful in fixing alignment of road, railways, canals etc.

Description : State the function of Anallatic lens..

Last Answer : The function of anallatic lens is to make additive constant zero i.e.(f+d)=0 It simplifies the calculation.

Description : Define Latitude and Departure.

Last Answer : Latitude : The projection of survey line parallel to meridian is called latitude. OR Projection of survey line parallel to N-S direction is called latitude. Departure: The projection of survey ... is called departure. OR Projection of survey line parallel to E-W direction is called departure.

Description : Define Swinging & Transiting

Last Answer : Swinging: It is the process of turning the telescope in horizontal plane about its vertical axis. Transiting: It is the process of turning the telescope through 180° in a vertical plane about its horizontal axis

Description : State two advantages of plane table surveying

Last Answer : 1.it is most rapid method of surveying. 2. it is suitable for magnetic areas. 3.The map can be prepared easily ,and does not require greater skill. 4.Irregular objects can be represented ... is less costly. 7 The check lines detects the errors of measurement and plotting on field itself.

Description : State any four characteristics of contours with sketches.

Last Answer : Characteristics of contours - The characteristics of contours are described in following statements with the help of necessary sketches. 1. All the points on contour line represent same reduced level or equal ... 8. The summit of four ridge lines represents saddle as shown in sketch 8.

Description : Explain direct method of contouring.

Last Answer : Direct method of contouring - In this method of contouring, the contours of required reduced level are plotted on ground itself. The procedure of direct method of contouring is as follows. ... identical coloured pegs, we get the required contours on ground by this direct method of contouring.

Description : Define transiting and swinging of theodolite.

Last Answer : Transiting of theodolite - The vertical movement of telescope about its horizontal axis through 360 degree is known as Transiting of telescope of theodolite. Swinging of theodolite - The lateral or ... of theodolite about its vertical axis through 360 degree is known as Swinging of theodolite.