What wire size needed for 120 volt 3000 watt load?

What wire size needed for 120 volt 3000 watt load?
by

1 Answer

Answer :

AWG # 10 wire on 30 amp circuit.
by

Related questions

What current is required to light two 75 watt lamps and one 40 watt lamp when connected in series to a 120 volt power source? A. 0.161 amperes B. 0.631 amperes C. 1.583 amperes D. 6.199 amperes

Description : What current is required to light two 75 watt lamps and one 40 watt lamp when connected in series to a 120 volt power source? A. 0.161 amperes B. 0.631 amperes C. 1.583 amperes D. 6.199 amperes

Last Answer : Answer: C

How much current does a 1500 Watt heater draw if supplied with a 120 Volt source?

Description : How much current does a 1500 Watt heater draw if supplied with a 120 Volt source?

Last Answer : ANSWER: 12.5 AMPS

Used normally, a 150-watt, 120 volt light bulb requires how many amps of current?

Description : Used normally, a 150-watt, 120 volt light bulb requires how many amps of current?

Last Answer : ANSWER: 1.25 AMPS 

An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Last Answer : ANSWER: Z -- 200 OHMS

Which of the following is not a unit of energy? a.Joule b.kW c.N-m d.Electron volt e.Watt-hour

Description : Which of the following is not a unit of energy? a.Joule b.kW c.N-m d.Electron volt e.Watt-hour

Last Answer : b. kW

If voltage across a bulb rated 220 volt-100 watt drops by `2.5 %` of its value, the percentage of the rated value by which the power would decrease is

Description : If voltage across a bulb rated 220 volt-100 watt drops by `2.5 %` of its value, the percentage of the rated value by which the power would decrease is

Last Answer : If voltage across a bulb rated 220 volt-100 watt drops by `2.5 %` of its value, the percentage of the rated value ... 20%` B. `2.5%` C. `5%` D. `10%`

What is the amp draw for a 3800 watt 240 volt water heater?

Description : What is the amp draw for a 3800 watt 240 volt water heater?

Last Answer : What is the answer ?

Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch

Description : Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is _______________. A. 200 watts B. 100 watts C. 50 watts D. equal to the product of the amperes times the voltage in each branch

Last Answer : Answer: A

Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply? A. The 75 watt lamp will draw as much current as the 100 watt lamp. B. The 100 watt lamp will have a greater resistance. C. Current flow will be the same across each lamp. D. The 75 watt lamp will have a higher resistance.

Description : Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply? A. The 75 watt lamp will draw as much current as the 100 ... Current flow will be the same across each lamp. D. The 75 watt lamp will have a higher resistance.

Last Answer : Answer: D

The unit of electrical resistance is the _____________. A. ampere B. volt C. watt D. ohm

Description : The unit of electrical resistance is the _____________. A. ampere B. volt C. watt D. ohm

Last Answer : Answer: D

Electric current is the flow of electrons through a conductor. The rate of this flow is measured as ___________. A. volts/watt B. amperes/centimetre C. coulombs/second D. ohms/volt

Description : Electric current is the flow of electrons through a conductor. The rate of this flow is measured as ___________. A. volts/watt B. amperes/centimetre C. coulombs/second D. ohms/volt

Last Answer : Answer: C

Name the quantities which are measured by the following units. (i) Newton (ii) Joule (iii) Watt (iv) Volt (v) Light year (vi) Angstrom (vii) Acre-foot (viii) Becquerel (ix) Hertz (x) Cusec

Description : Name the quantities which are measured by the following units. (i) Newton (ii) Joule (iii) Watt (iv) Volt (v) Light year (vi) Angstrom (vii) Acre-foot (viii) Becquerel (ix) Hertz (x) Cusec

Last Answer : Answers: (i) Force (ii) Work Energy (iii) Power of electricity (iv) Potential difference (v) Distance of stars and planets (vi) Length (vii) Volume (viii) Radioactivity (ix) Frequency (x) Rate of flow of water

What is the unit of responsitivity? ∙ a. Ampere/volt ∙ b. Ampere/watt ∙ c. Watt/ampere ∙ d. Volts/ampere

Description : What is the unit of responsitivity? ∙ a. Ampere/volt ∙ b. Ampere/watt ∙ c. Watt/ampere ∙ d. Volts/ampere

Last Answer : ∙ a. Ampere/volt

Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply.

Description : Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply. The potential difference across 60 watt lamp will be: A) 195 volt B) 220 volt C) 245 volt D) 440 volt

Last Answer : Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply. The potential difference across 60 watt lamp will be: 245 volt

What is the difference between watt volt and ampere?

Last Answer : Difference between watt and volt and ampere is as follows: Watt Volt Ampere Watt is the unit of power. Volt is the unit of voltage. Ampere is the unit of current. Watts= Volts x Amperes Volts= Watts/ ...

Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per m2 of steel strip. (A) 5-10 (B) 1000-1500 (C) 120-500 (D) 1500-3000

Description : Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per m2 of steel strip. (A) 5-10 (B) 1000-1500 (C) 120-500 (D) 1500-3000

Last Answer : Option C

Ajay sold a motorbike at a profit of 20% to Balu. Balu sold it to Dinesh at a loss of 20%. If the profit made by Ajay was Rs.120 less than the loss made by Balu, find the cost price of Ajay(in Rs.) a)3000 b)3600 c)3900 d)4500

Description : Ajay sold a motorbike at a profit of 20% to Balu. Balu sold it to Dinesh at a loss of 20%. If the profit made by Ajay was Rs.120 less than the loss made by Balu, find the cost price of Ajay(in Rs.) a)3000 b)3600 c)3900 d)4500

Last Answer : a)3000

The average monthly salary of directors & office boys of an organization Rs. 3750. Then the average salary of all directors is Rs. 6000 while that of all office boys is Rs. 3000 per month. If there are 120 employees in the organization then find the ratio of manager and office boy. A) 2:5 B) 3:1 C) 1:3 D) 5:2

Description : The average monthly salary of directors & office boys of an organization Rs. 3750. Then the average salary of all directors is Rs. 6000 while that of all office boys is Rs. 3000 per month. If there are 120 employees in the ... find the ratio of manager and office boy. A) 2:5 B) 3:1 C) 1:3 D) 5:2 

Last Answer :  C)  let the number of director be X and office boy be 120-x total salary of director and office boy = 120*3750 = Rs.450000 total salary of director = 6000x total salary of office boy = 3000* (120 - ... director number of office boy = 120-30 = 90 ratio of director to office boy = 30:90 = 1:3

Will a 110 watt receiver power 120 watt speakers?

Description : Will a 110 watt receiver power 120 watt speakers?

Last Answer : Yes. Here’s how to think of it—it’s not that 120 watt speakers draw 120 watts, it’s that they can handle up to 120 watts.

Where can I find a 78mm Type J 120 Volt Halogen bulb locally?

Description : Where can I find a 78mm Type J 120 Volt Halogen bulb locally?

Last Answer : answer:Batteries Plus has a ton of lightbulbs and seems to have a few stores in Massachusetts. I don’t see a “Boston” store, but if I remember right there’s not much “Boston” really, it’s all about the smaller neighborhoods and suburbs. Maybe one is close?

The electrical schematic shown in the illustration indicates the lighting feeder circuit is _____________. EL-0014 A. three phase, 450 volt, and 60 cycle B. three phase, 120 volt, and 60 cycle C. single phase, 120 volt, and 60 cycle D. not specified

Description : The electrical schematic shown in the illustration indicates the lighting feeder circuit is _____________. EL-0014 A. three phase, 450 volt, and 60 cycle B. three phase, 120 volt, and 60 cycle C. single phase, 120 volt, and 60 cycle D. not specified

Last Answer : Answer: A

An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Description : An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Last Answer : Answer: B

If there is a reduction in the normally supplied frequency to a 120/240 volt, threephase AC current motor from 60 hertz to 55 hertz, the motor would _____________. A. run at a slower speed B. operate at a lower current C. overheat D. trip off the line

Description : If there is a reduction in the normally supplied frequency to a 120/240 volt, threephase AC current motor from 60 hertz to 55 hertz, the motor would _____________. A. run at a slower speed B. operate at a lower current C. overheat D. trip off the line

Last Answer : Answer: A

Which of the listed sections of an emergency switchboard is used to supply power for alarm signals under emergency conditions? A. The generator and bus transfer section B. The 450 volt, 60 cycle, 3 phase bus C. The 120 volt, 3 phase, 60 cycle bus D. The 24 volt DC bus

Description : Which of the listed sections of an emergency switchboard is used to supply power for alarm signals under emergency conditions? A. The generator and bus transfer section B. The 450 volt, 60 cycle, 3 phase bus C. The 120 volt, 3 phase, 60 cycle bus D. The 24 volt DC bus

Last Answer : Answer: D

A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and

Description : A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and armature resistance are 100 volt and 0.5Ω respectively. With the magnitude control ratio 0.6, the quadrant of operation DC motor is  (a) First (b) Second (c) Third (d) Fourth

Last Answer : A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and armature resistance are 100 volt and 0.5Ω respectively. With the magnitude control ratio 0.6, the quadrant of operation DC motor is First

Three lamps are connected in parallel across a 120 Volt source. If one lamp burns out, the remaining two will ...

Description : Three lamps are connected in parallel across a 120 Volt source. If one lamp burns out, the remaining two will be: A. Glow dimmer B. Glow brighter C. Not light D. Glow with the same brightness as before

Last Answer : Glow with the same brightness as before 

What wire gauge and amperage for a 1600 watt wall heater?

Description : What wire gauge and amperage for a 1600 watt wall heater?

Last Answer : 1600 watts is unusually low for electric baseboard heaters! These usually are rated at about 6000 watts.Typical electric baseboard heaters operate on 220 volts thus you heater would pull about 7.3 ... handle this.A standard 6000 watt baseboard heater pulls about 27 amperes and needs 10 gauge wire.

When a current of `(2.5 +- 0.5)` ampere flows through a wire, it develops a potential difference of `(20 +- 1)` volt, the resistance of the wire is

Description : When a current of `(2.5 +- 0.5)` ampere flows through a wire, it develops a potential difference of `(20 +- 1)` volt, the resistance of the wire is

Last Answer : When a current of `(2.5 +- 0.5)` ampere flows through a wire, it develops a potential difference of `(20 +- ... `(8 pm 1.5)Omega` D. `(8 pm 3)Omega`

A potentiometer wire of length 10 m and resistance `10 Omega` per meter is connected in serice with a resistance box and a 2 volt battery. If a potent

Description : A potentiometer wire of length 10 m and resistance `10 Omega` per meter is connected in serice with a resistance box and a 2 volt battery. If a potent

Last Answer : A potentiometer wire of length 10 m and resistance `10 Omega` per meter is connected in serice with a ... Omega` C. `190 Omega` D. `90 Omega`

A potentiometer circuit is setup as shown. The potential gradient across the potentiometer wire is `k "volt"//cm` and the ammeter present in the circu

Description : A potentiometer circuit is setup as shown. The potential gradient across the potentiometer wire is `k "volt"//cm` and the ammeter present in the circu

Last Answer : A potentiometer circuit is setup as shown. The potential gradient across the potentiometer wire is `k "volt"//cm` and ... (2)` D. `kl_(1)"and"kl_(2)`

The length of a wire of a potentiometer is 100 cm, and the e.m.f. of its standard cell is E volt. It is employed to measure the e.m.f. of a battery wh

Description : The length of a wire of a potentiometer is 100 cm, and the e.m.f. of its standard cell is E volt. It is employed to measure the e.m.f. of a battery wh

Last Answer : The length of a wire of a potentiometer is 100 cm, and the e.m.f. of its standard cell is E ... current in the potentiometer wire D. `(30E)/(100)`

A coil is wound with 400 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 4.8 amps B. 7.06 amps C. 10.65 amps D. 11.27 amps

Description : A coil is wound with 400 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 4.8 amps B. 7.06 amps C. 10.65 amps D. 11.27 amps

Last Answer : Answer: B

A coil is wound with 200 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 1.14 amps B. 7.04 amps C. 10.22 amps D. 14.08 amps

Description : A coil is wound with 200 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 1.14 amps B. 7.04 amps C. 10.22 amps D. 14.08 amps

Last Answer : Answer: D

In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Description : In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Last Answer : Answer: B

How much resistance is needed to draw 17.6 mA from a 12 volt source?

Description : How much resistance is needed to draw 17.6 mA from a 12 volt source? A.212 ohms B.6.8 kohms C.68 ohms D.680 ohms

Last Answer : How much resistance is needed to draw 17.6 mA from a 12 volt source? A.212 ohms B.6.8 kohms C.68 ohms D.680 ohms

A 3.2 m diameter balloon is filled with Helium. The total weight of balloon, gas and pay load is 10 kg kg. In an isothermal atmosphere having conditions identical to N.T.P. the balloon will rise to a height of about a.6000 m b.1500 m c.3000 m d.2000 m e.1000 m

Description : A 3.2 m diameter balloon is filled with Helium. The total weight of balloon, gas and pay load is 10 kg kg. In an isothermal atmosphere having conditions identical to N.T.P. the balloon will rise to a height of about a.6000 m b.1500 m c.3000 m d.2000 m e.1000 m

Last Answer : a. 6000 m

A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2 , the stresses developed are: (A) b = 10 N/mm2s = 20 N/mm2(B) b = 8 N/mm2s = 16 N/mm2(C) b = 6 N/mm2s = 12 N/mm2(D) b = 5 N/mm2s = 10 N/mm

Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that  of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2  MN/mm2  and Eb = 0.1 ... 6 N/mm2 s  = 12 N/mm2 (D) b = 5 N/mm2 s  = 10 N/mm

Last Answer : (A) b = 10 N/mm2 s  = 20 N/mm

At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total

Description : At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is :  (A) 7000 W (B) 6000 W (C) 8000 W (D) 4000 W

Last Answer : At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is : 6000 W

The standard method of controlling the output voltage of a 440 volt, 60 Hz, AC generator is accomplished by adjusting the ____________. A. prime mover speed droop B. number of poles C. alternator field excitation D. load on the alternator

Description : The standard method of controlling the output voltage of a 440 volt, 60 Hz, AC generator is accomplished by adjusting the ____________. A. prime mover speed droop B. number of poles C. alternator field excitation D. load on the alternator

Last Answer : Answer: C

The output voltage of a 440 volt, 60 Hz AC generator is controlled by the ______________. A. load on the alternator B. load on the prime mover C. speed of the prime mover D. exciter output voltage

Description : The output voltage of a 440 volt, 60 Hz AC generator is controlled by the ______________. A. load on the alternator B. load on the prime mover C. speed of the prime mover D. exciter output voltage

Last Answer : Answer: D

The output voltage of a 440 volt, 60 hertz, AC generator is controlled by the _____________. A. prime mover speed B. exciter output voltage C. load on the alternator D. number of poles

Description : The output voltage of a 440 volt, 60 hertz, AC generator is controlled by the _____________. A. prime mover speed B. exciter output voltage C. load on the alternator D. number of poles

Last Answer : Answer: B

[23] Transformers are rated in KVA instead of KW because A. load power factor is often not known B. KVA is fixed whereas KW depends on load power factor C. Total transformer loss depends on volt ampere D. It has become customary

Description : [23] Transformers are rated in KVA instead of KW because A. load power factor is often not known B. KVA is fixed whereas KW depends on load power factor C. Total transformer loss depends on volt ampere D. It has become customary

Last Answer : C. Total transformer loss depends on volt ampere

The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to :

Description : The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to :

Last Answer : The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to : Z (p.u)

A steel wire having cross sectional area 1.2 mm is stretched by a force of 120 N.

Description : A steel wire having cross sectional area 1.2 mm is stretched by a force of 120 N.

Last Answer : A steel wire having cross sectional area 1.2 mm is stretched by a force of 120 N. If a ... is produced in the wire, calculate the Poisson's ratio.

A long conducting wire carrying a current I is bent at `120^(@) `( see figure). The magnetic field B at a point P on the right bisector of bending ang

Description : A long conducting wire carrying a current I is bent at `120^(@) `( see figure). The magnetic field B at a point P on the right bisector of bending ang

Last Answer : A long conducting wire carrying a current I is bent at `120^(@) `( see figure). The magnetic field B at a ... (3pid))` D. `(sqrt(3mu_(0)I))/(2pid)`

How much stone is needed in a 30' x 120' area with 4 thick?

Description : How much stone is needed in a 30' x 120' area with 4 thick?

Last Answer : 40 tons of stone

To hydrate 500kg of cement full water needed, is (A) 100 kg (B) 110 kg (C) 120 kg (D) 130 kg

Description : To hydrate 500kg of cement full water needed, is (A) 100 kg (B) 110 kg (C) 120 kg (D) 130 kg

Last Answer : Answer: Option D

Large cable sizes are formed as individual conductors that may be comprised of several smaller strands to __________. A. obtain the flexibility required for easy handling B. reduce the overall weight of the wire run C. reduce the number of supports needed for a horizontal overhead run D. all of the above

Description : Large cable sizes are formed as individual conductors that may be comprised of several smaller strands to __________. A. obtain the flexibility required for easy handling B. reduce the overall weight of the ... . reduce the number of supports needed for a horizontal overhead run D. all of the above

Last Answer : Answer: A