With the help of neat sketch, describe block diagram of Electronic Diesel Control Unit (EDC).

With the help of neat sketch, describe block diagram of Electronic Diesel Control Unit (EDC).
by

1 Answer

Answer :

EDC: The ECU determines the correct quantity of the fuel to be injected based on the inputs and the data in the look up table. The fuel input depends on the rack position and thus ECU controls the rack position using a solenoid. The position of the rack is measured and used for feedback. The accelerator pedal position is the input from the driver and a potentiometer is used to sense it. The system can maintain the vehicle speed at any set value. The ECU can also regulate the fuel quantity depending on other conditions like braking. The ECU can also protect the engine against overheating by regulating the maximum quantity of fuel delivered.

image

by

Related questions

Draw block diagram for EDC type fuel pump in diesel engine.

Description : Draw block diagram for EDC type fuel pump in diesel engine.

Last Answer : Block diagram for EDC type fuel pump in diesel engine OR

Explain the working of diesel engine glow plugs with neat sketch

Description : Explain the working of diesel engine glow plugs with neat sketch

Last Answer : Glow plug is an aid for cold starting of a C.I. engine. The self-ignition temperature of diesel is 250°C. For compression ignition, the charge (air + diesel) should reach a temperature of ... plugs is automatically interrupted. But starting may be attempted again as soon as the driver wishes.   

Describe with neat sketch operation of PCV valve under different engine operating condition to control/ emission

Description : Describe with neat sketch operation of PCV valve under different engine operating condition to control/ emission

Last Answer : PCV Valve: It consists of a spring loaded tapered valve for flow control. The crankcase pressure and manifold vacuum act together to close the valve whereas the spring pressure tends to keep it open.( ... at idle and low speed (c)High speed/Load operation (d)Preventing backfire during cranking  

Describe the construction and working of D-MPFI and L-MPFI with help of neat sketch.

Description : Describe the construction and working of D-MPFI and L-MPFI with help of neat sketch.

Last Answer : D-LMFI System: It is Manifold fuel injection system.In this type, the vacuum in the intake manifold and volume of air by its density are sensed in this type of MPFI system .As air enters into ... intake manifold , the air flow sensor measures the amount of air and sends information to ECU.

Write neat sketch, describe MPFI system.

Description : Write neat sketch, describe MPFI system.

Last Answer : MPFI system In the port injection arrangement, the injectoe is placed on the side of the intake manifold near the intake port. The injector sprays gasoline into the air, inside the intake manifold. The ... manifold. If there are six cylinders, there will be six injectors as shown in figure.

Describe the working of EGR valve with neat sketch.

Description : Describe the working of EGR valve with neat sketch.

Last Answer : Answer: Exhaust Gas Recirculation Valve (Operation-2 marks, Sketch-2 marks) When the engine is idling, the EGR valve is closed and there is no EGR flow into the manifold. The EGR valve remains closed ... exhaust gas (less than 10% of total) to be supplied into the incoming air: fuel mixture

Describe the working of fuel injector with neat sketch

Description : Describe the working of fuel injector with neat sketch

Last Answer : Fuel Injector: The injector assembly consists of - i) a needle valve ii) a compression spring iii) a nozzle iv) an injector body When the fuel is supplied to lift the injection ... spring tension and hence the valve opening pressure is controlled by adjusting the screw provided at the top.

Illustrate with neat sketch the process to control production of NOx in combustion chamber.

Description : Illustrate with neat sketch the process to control production of NOx in combustion chamber.

Last Answer : Method to control NOx: The EGR system is used to reduce the amount of NOx in the exhaust. NOx production increases as the temperature inside the combustion chamber rises due to acceleration or heavy engine loads, ... (less than 10% of total) to be supplied into the incoming air: fuel mixture.  

Draw a labeled block diagram of CNG conversion Kit. Describe it’s working

Description : Draw a labeled block diagram of CNG conversion Kit. Describe it’s working

Last Answer : Working of CNG Kit: The Sequential Injection system still has a high pressure tank, filler, filter and regulator, the regulator is different in that it puts out a steady pressure as opposed ... , natural gas temperature sensor and coolant temperature sensor to operate and control the system.  

Draw a block diagram of CRDI system and describe its working.

Description : Draw a block diagram of CRDI system and describe its working.

Last Answer : Working of CRDI system: High pressure pump provides high pressure fuel to the common rail. The common rail stores the fuel and maintains a constant pressure in the common rail line (approximately 1500 bars.). ... rate can be modified by controlling the nozzle needle movement. OR

List four types of combustion chambers used in S.I. engine. Explain any one in detail with neat sketch.

Description : List four types of combustion chambers used in S.I. engine. Explain any one in detail with neat sketch.

Last Answer : Combustion chambers used in S.I. engine:- 1) T - Head 2) I - Head. 3) F - Head. 4) L - Head 5) Divided combustion chamber. 1. T Head Type Combustion chambers.  This ... and therefore more heat loss. 4. Valve size restricted. 6. Thermal failure in cylinder block also. 

Draw neat sketch of pre-combustion chamber and name its parts.

Description : Draw neat sketch of pre-combustion chamber and name its parts.

Last Answer : Fig. Pre-combustion chamber

Draw neat sketch to show TBI system of SI engine and name its parts.

Description : Draw neat sketch to show TBI system of SI engine and name its parts.

Last Answer : Draw neat sketch to show TBI system of SI engine and name its parts.

Explain PFI system with neat sketch.

Description : Explain PFI system with neat sketch.

Last Answer : PFI system In the port injection arrangement, the injector is placed on the side of the intake manifold near the intake port. The injector sprays gasoline into the air, inside the intake manifold. The ... of gasoline and air then passes through the intake valve and enters into the cylinder.

State the different types of SI engine combustion chambers. Draw a neat sketch of any one.

Description : State the different types of SI engine combustion chambers. Draw a neat sketch of any one.

Last Answer : 1) T Head Type Combustion chambers 2) L Head Type Combustion chambers 3) F- Head combustion chamber 4) Over head valve or I head combustion chamber 5) Hemispherical combustion chamber 6) Bathtub ... - Head combustion chamber 4) Over head valve or I head combustion chamber

Draw neat sketch of swirl type combustion chamber of IDI engine.

Description : Draw neat sketch of swirl type combustion chamber of IDI engine.

Last Answer : Fig. swirl type combustion chamber of IDI engine.

Explain the phenomenon of diesel knocking with the help of P-Ø diagram.

Description : Explain the phenomenon of diesel knocking with the help of P-Ø diagram.

Last Answer : Explanation- The knock phenomenon of C.I. engine depends upon delay period. If delay period is small then less amount of fuel is admitted into cylinder. When small amount of ... I. engines, higher compression ratio causes lesser ignition delay and hence lesser possibility of diesel knocks.

State input and output control functions of ECM. Describe the idle speed control with sketch.

Description : State input and output control functions of ECM. Describe the idle speed control with sketch. 

Last Answer : Inputs and outputs of Electronic Control Module The inputs of ECM 1. The Ignition (Engine Speed Sensor). 2. Temperature Sensor (Coolant Temperature). 3. Throttle Potentiometer (Intake ... through. The Idle speed control valve stepper motor allows 125 possible valve opening positions. 

What is EGR? Explain with the help of block diagram.

Description : What is EGR? Explain with the help of block diagram.

Last Answer : Exhaust Gas Recirculation Valve (Operation-2 marks, Sketch-2 marks) When the engine is idling, the EGR valve is closed and there is no EGR flow into the manifold. The EGR valve remains closed until the ... exhaust gas (less than 10% of total) to be supplied into the incoming air: fuel mixture

With the help of suitable sketch describe the working of pressure regulator.

Description : With the help of suitable sketch describe the working of pressure regulator.

Last Answer : Working of pressure regulator : The fuel pump provides more fuel than the maximum required by the engine. Fuel not used by the engine is returned to the fuel tank. The fuel rail supplies all injectors. The pressure ... between 2.0 and 3.5 bar and allows excess fuel to return to the fuel tank.

Explain working of LPG kit with labeled block diagram.

Description : Explain working of LPG kit with labeled block diagram.

Last Answer : Working of LPG Kit: LPG Tank: It is used to store the LPG at 10 bar Filler Valve: It allows the LPG into the tank while feeling. Pressure Relief Valve: It is used to limit ... regulator Mixer / gas injection which flows the LPG into the combustion chamber  Block diagram:  

Draw a labelled block diagram of CRDI system

Description : Draw a labelled block diagram of CRDI system

Last Answer : block diagram of CRDI system

Describe air fuel- ratio requirements for diesel engines at no load to full load.

Description : Describe air fuel- ratio requirements for diesel engines at no load to full load.

Last Answer : Irrespective of load at any given speed, an approximately constant supply of air enters the cylinder. With change in load, the quantity of fuel injected is changed varying the air fuel ratio. The ... engine always designed to operate with an excess air of 15 to 40% depending upon the application

Describe the working of electronically controlled diesel injection pump.

Description : Describe the working of electronically controlled diesel injection pump. 

Last Answer : Answer: Electronically controlled diesel injection pump: This is similar to conventional pumps, but its injection is controlled by Electronic Control Unit (ECU) which control solenoid valve in the injection pump ... modifies the current to the solenoid valve, to supply fuel as per requirement.  

List three methods of fuel injection. Describe sequential method with suitable sketch.

Description : List three methods of fuel injection. Describe sequential method with suitable sketch.

Last Answer : Methods of petrol injection 1. Sequential fuel injection. (SFI) 2. Grouped fuel injection. 3. Simultaneous fuel injection 4. Continuous injection.  Sequential Injection: Each injector ... to crank/ camshaft position and pulse width, can be optimized for each individual cylinder.

Describe construction and working of TBI system with suitable sketch.

Description : Describe construction and working of TBI system with suitable sketch.

Last Answer : Construction and working of TBI system: Throttle Body Injection is an electronically controlled injection system in which an electronic fuel injector injects the fuel intermittently in to the intake manifold ... to calculate the triggering signals for the injectors and other system actuators.

What is diesel smoke? State two methods to control diesel smoke.

Description : What is diesel smoke? State two methods to control diesel smoke.

Last Answer : Diesel smoke: Smoke is defined as visible products of combustion, is due to poor combustion. It originates early in the combustion. Rich fuel-air mixture & at pressures developed in diesel ... manifold. This shortens the delay period- curbs thermal cracking which is responsible for soot format

Draw a labeled block of LPG conversion kit. Describe its working.

Description : Draw a labeled block of LPG conversion kit. Describe its working.

Last Answer : Working of CNG Kit: The Sequential Injection system still has a high pressure tank, filler, filter and regulator, the regulator is different in that it puts out a steady pressure as opposed ... , natural gas temperature sensor and coolant temperature sensor to operate and control the system.

Explain working of Variable Valve Timing and Electronic lift control (VTEC) system. Enlist its advantage and Drawbacks

Description : Explain working of Variable Valve Timing and Electronic lift control (VTEC) system. Enlist its advantage and Drawbacks

Last Answer : Answer: Working of Variable Valve Timing and Electronic lift control (VTEC) system:- VTEC (which stands for Variable Valve Timing and Lift Electronic Control) is an electronic and mechanical system ... 2) Maintenance cost is high 3) Very complex structure required complicated control system.

Differentiate air fuel ratio between carburetted engine and electronic fuel injection engines control system.

Description : Differentiate air fuel ratio between carburetted engine and electronic fuel injection engines control system.

Last Answer : Sr. No. Carburetted engine Electronic Fuel Injection (EFI) engine 1 Fuel atomization depends upon velocity of air in the venturi. Atomization of fuel is independent of cranking ... occurs in carbureted engine. Equal quantity of fuel is supplied to port for each cylinder

List and Explain two type of diesel smoke. Explain four cause of diesel smoke.

Description : List and Explain two type of diesel smoke. Explain four cause of diesel smoke.

Last Answer : Answer: Two type of diesel smoke 1) Blue-white smoke 2) Black smoke Four cause of diesel smoke:- 1) Blue smoke is due to burning the droplets of lubricating oil in combustion ... because of worn piston rings & cylinder liners & water come in combustion chamber because cracked water jacket.

Compare detonation and diesel knock on the basis of (i) Fuel Ignition Temperature (ii) Compression Ratio (iii) Speed (iv) inlet temperature (v) inlet pressure (vi) cylinder wall temperature (vii) cylinder size

Description : Compare detonation and diesel knock on the basis of (i) Fuel Ignition Temperature (ii) Compression Ratio (iii) Speed (iv) inlet temperature (v) inlet pressure (vi) cylinder wall temperature (vii) cylinder size 

Last Answer : Comparison between detonation and diesel knock: Parameter To avoid Detonation in SI Engine  To avoid Diesel knock i) Fuel Ignition Temperature High Low ii) Compression Ratio ... Cylinder wall temperature Low High viii) Cylinder size Small Large

List down the pollutants from gasoline engine and diesel engine.

Description : List down the pollutants from gasoline engine and diesel engine.

Last Answer : Pollutants from gasoline engine:- 1. Hydrocarbons. 2. Carbon Monoxide. 3. Carbon dioxide. 4. Oxides of Nitrogen. Pollutants from diesel engine:- 1. Hydrocarbons 2. Carbon Monoxide. 3. Carbon dioxide. 4. Oxides of Nitrogen. 5. Particulate matters.

State the difference between turbocharger & VGT used in diesel engine.

Description : State the difference between turbocharger & VGT used in diesel engine.

Last Answer : Difference between turbocharger and VGT Sr. No. Parameter Turbocharger VGT 1 Fuel efficiency Lower fuel efficiency as compared to VGT Improved fuel efficiency by20% 2 ... required. 6 Engine response Sluggish response at low speeds Quick responsive engine

Write the values of boiling temperature for cetane(diesel).iso-octane(petrol), Butane, Propane an methane fuel and write effect of it on its system.

Description : Write the values of boiling temperature for cetane(diesel).iso-octane(petrol), Butane, Propane an methane fuel and write effect of it on its system.

Last Answer : Write the values of boiling temperature for cetane(diesel).iso-octane(petrol), Butane, Propane an methane fuel and write effect of it on its system.

Compare the following fuels on the basis of calorific value and knocking. LPG, CNG and bio-diesel

Description : Compare the following fuels on the basis of calorific value and knocking. LPG, CNG and bio-diesel 

Last Answer : Parameter LPG CNG Bio-diesel Calorific value 46.4MJ/Kg LPG has consistent & higher calorific value.  52.34 MJ/Kg Which is higher than LPG. 37.27 MJ/Kg this ... 65 which is higher than petro-diesel. So intensity of knocking is less in biodiesel compared to petro diesel.

Draw a layout of fuel injection system in CRDI diesel engine. State its fundamental requirement.

Description : Draw a layout of fuel injection system in CRDI diesel engine. State its fundamental requirement.

Last Answer : Fundamental requirement:-The line diagram of CRDI shows that the system is controlled by ECU. The sensors in the system are used to feed the input in the ECU.ECU will provide the signal ... fuel injector, common rail, High pressure fuel pump, ECM/ECU, Pressure sensor, Rail pressure limiter. 

Write the properties of diesel as a fuel in CI engine.

Description : Write the properties of diesel as a fuel in CI engine.

Last Answer : 1) Volatility: - The fuel should be sufficiently volatile in the operating range of temperature to produce good mixing and combustion. 2) Viscosity: Viscosity of a fuel is a measure of its resistance to flow. ... the temperature of unit mass of a diesel through 1°c. It is about 1.9 KJ/Kg°c.

What is diesel knock? How it is controlled?

Description : What is diesel knock? How it is controlled?

Last Answer : Diesel knock The knock phenomenon of C.I. engine depends upon delay period. If delay period is small then less amount of fuel is admitted into cylinder during ignition delay period. As it burns ... by multiple injections so that only small amount of fuel is injected at first (pilot injection). 

What are the causes of diesel smoke?

Description : What are the causes of diesel smoke?

Last Answer : Cause of diesel smoke:- 1) Blue smoke is due to burning the droplets of lubricating oil in combustion chamber because of worn piston rings & cylinder liners. 2) White smoke is due to ... of worn piston rings & cylinder liners & water come in combustion chamber because cracked water jacket. 

Sketch and Explain F-head combustion chamber.

Description : Sketch and Explain F-head combustion chamber.

Last Answer : In F-head combustion chamber one valve is in head and other in the block. This design is a compromise between L-head and I head combustion chambers. Advantages are : High volumetric ... This design is the complex mechanism for operation of valves and expensive special shaped piston. 

List eight ways of reducing pollution. Explain PCV and evaporative emission system with suitable sketch.

Description : List eight ways of reducing pollution. Explain PCV and evaporative emission system with suitable sketch.

Last Answer : Eight ways of reducing pollution:-  1) Optimize Ignition Advance 2) Use unleaded gasoline & Low sulphur diesel 3) Use leaner air fuel ratio 4) Use exhaust gas treatment devices ex Catalytic ... check valve. The EVAP system is designed to limit maximum vacuum and pressure in the fuel tank.

With neat labeled figure, explain the working of any two position of PCV (positive crank case ventilation) valve.

Description : With neat labeled figure, explain the working of any two position of PCV (positive crank case ventilation) valve.

Last Answer : PCV Valve: It consists of a spring loaded tapered valve for flow control. The crankcase pressure and manifold vacuum act together to close the valve where as the spring pressure tends to keep it open.(Fig a ... back seat sealing the inlet and crankcase is protected from the back fire.(Fig d).

Describe the idle speed control function of an electronic control module with neat sketch.

Description : Describe the idle speed control function of an electronic control module with neat sketch.

Last Answer : Idle Speed Control System as Output Function of ECM: While the engine is being started, or operated, the logic module of Electronic Control Module (ECM) will signal the Stepper motor of Idle Speed ... speed control valve stepper motor allows 125 possible valve opening positions. OR

Explain with neat sketch block diagram of optical fiber communication system and list out sources and detectors suitable for it.

Description : Explain with neat sketch block diagram of optical fiber communication system and list out sources and detectors suitable for it.

Last Answer : OR 1. The light source is normally an infrared LED or LASER device which is driven by the current value from the V to I convertor. It emits light which is proportional ... optical energy electrical signal. The light detectors which are used as PIN photodiode and avalanche photo diode.

Draw P-Q diagram for stages of combustion in SI engine and write stages of combustion with its explanation.

Description : Draw P-Q diagram for stages of combustion in SI engine and write stages of combustion with its explanation.

Last Answer : The stages of combustion in S.I. engine: Stage I: Ignition Lag or Preparation Phase: It is a chemical process which depends on-nature of fuel, temperature & pressure, ... The rate of combustion reduces due to surface of the flame front becoming smaller and reduction in turbulence.

Draw the circuit diagram of glow plug and explain its operation.

Description : Draw the circuit diagram of glow plug and explain its operation.

Last Answer : Answer: Operation of glow plug: Glow plug is an aid for cold starting of a C.I. engine. The selfignition temperature of diesel is 250°C. For compression ignition, the charge (air + diesel) ... is automatically interrupted. But starting may be attempted again as soon as the driver wishes. 

Draw P-ⱷ diagram showing stages of combustion in SI engine.

Description : Draw P-ⱷ diagram showing stages of combustion in SI engine.

Last Answer : Stages of combustion in SI engines  Stage I: Ignition Lag or Preparation Phase: The time elapsed between the fuel injection into the combustion chamber and starting of combustion. It is the growth ... reduces due to surface of the flame front becoming smaller and reduction in turbulence.   

Draw a neat labeled block diagram of 3-phase Electronic Energy meter.

Description :  Draw a neat labeled block diagram of 3-phase Electronic Energy meter.

Last Answer : Labeled diagram of 3-phase electronic energy meter:

Describe the working of high pressure fuel pump.

Description : Describe the working of high pressure fuel pump. 

Last Answer : Working: Downward motion of plunger: The safety valve at the inlet opens if the pre-supply pressure of fuel exceeds 1.5 bars and fuel comes and fills the chamber till the plunger moves up to BDC. ... . A constant pressure of about 1400 to 1600 bar is maintained in the common rail.