Write-four uses of surveying.

Write-four uses of surveying.
by

2 Answers

Answer :

Uses of surveying.

1. To record relative positions of various points on the surface of earth.

2. Prepare plans and maps required for various works.

3. Layout of various engineering works.

4. Compute areas and volumes using survey data required for various purposes.

5. To prepare a topographic map

6. To prepare military map

7. To prepare a archeological map
by

Answer :

Uses of surveying are:

1) Surveying is useful to plot ground details in various maps like topographic and cadastral maps.

2) It is useful in navigational movement planning through military survey.

3) Surveying is also useful in almost all civil projects i.e. road, railway, dam, bridge and airport construction for longitudinal and transverse details.

4) It is highly needed in land cover and land use analysis through remote sensing techniques.

5) Surveying is a helping hand in tunnel excavation, underground piping and mining works.

6) It is truly beneficial in collecting details of water bodies on earth like lake, pond, river, sea etc.

by

Related questions

State the two uses of survey based on geodetic surveying

Description : State the two uses of survey based on geodetic surveying

Last Answer : Two uses of survey based on geodetic surveying:- i) To determine the precise position s on the surface of the earth. ii) Preparation of maps of large area like map of a country, state ... ) Establishment of GTS bench Marks across the country. iv) Preparation of military maps for defense purposes.

State any two uses of Plane Surveying.

Description : State any two uses of Plane Surveying. 

Last Answer : 1) Plane surveying is used for measuring small distance. 2) When area is less than 260 km2, plane survey is normally done. 3) When desired accuracy is less, plane survey is done.

State any four classification of surveying based on instrument uesd.

Description : State any four classification of surveying based on instrument uesd. 

Last Answer : i) Chain survey ii) Plane table survey iii) Theodolite survey, iv) Tachometric survey v) compass survey vi) photographic survey, vii) Aerial survey 

State any four precautions to be taken while selecting stations for chain surveying.

Description : State any four precautions to be taken while selecting stations for chain surveying.

Last Answer : Following are the precautions to be taken while selecting station for chain surveying. 1) As far as possible the survey work should be based upon the basic principle of surveying i.e. working from whole to ... level ground. 9) The survey lines should run as far as possible nearer to object.

The process of surveying is therefore in three stages namely:

Description : The process of surveying is therefore in three stages namely:

Last Answer : (i) Taking a general view This part of the definition is important as it indicates the need to obtain an overall picture of what is required before any type of survey work is undertaken. In ... of quantities, datasheets, drawings and in land surveying maps and plan showing the features on the land.

Tacheometric Surveying

Description : Tacheometric Surveying

Last Answer : Tacheometric is a branch of surveying in which horizontal and vertical distances are determined by taking angular observation with an instrument known as a tachometer. Tacheometric surveying is adopted in rough ... be prepared for investigation works within a short time on the basis of such survey.

Draw sketch and explain method of traversing of plane table surveying.

Description : Draw sketch and explain method of traversing of plane table surveying. 

Last Answer : Procedure: 1.Set plane table over station A use plumbing fork for transferring station point from ground on sheet. Draw the direction of magnetic meridian with the help of compass. 2. With the ... scale Similarly, the table can be set at other successive station and traverse is completed.

Describe back sighting method of orientation of plane table surveying.

Description : Describe back sighting method of orientation of plane table surveying.

Last Answer : Backsight method of orientation 1. Assume we have to orient the table at next station B' represented on paper by point b'. 2.the line ba' is drawn on previous station A'. 3.the alidade is kept ... A'. 4. When the plotted line ab' coincides with line AB' and table will be oriented.

Define surveying.

Description : Define surveying.

Last Answer : Surveying- It is branch of civil engineering in which relative positions of ground points are determined by taking linear and angular measurement.

Define surveying & state its objectives

Description : Define surveying & state its objectives

Last Answer : Surveying- It is branch of civil engineering in which relative positions of ground points are determined by taking linear and angular measurement. Objectives: 1. To determine the relative positions of ... quantities 4. To prepare a topographical map showing details of hills, valleys and rivers.

Explain ‘Intersection Method’ of plane table surveying with neat sketch. Also give situation when intersection method is used.

Description : Explain ‘Intersection Method’ of plane table surveying with neat sketch. Also give situation when intersection method is used.

Last Answer : 1. Lay out a base line AB and measure it and Plot a distance ab' on sheet using any scale. 2.Set up instrument at A' with a' over A' 3.Orient the table by placing alidade ... the case of the survey of mountainous country. 5. The only linear measurement required is that of a base line.

Explain principle of chain surveying

Description : Explain principle of chain surveying 

Last Answer : 1) Principle of chain surveying is triangulation 2) Triangulation consists of frame work of triangles. The whole area is divided into network of triangles. 3) A triangle is the only simple plane ... to be adopted depends upon the shape & configuration of the ground & the natural obstacles. 

State the use of alidade in plane table surveying

Description : State the use of alidade in plane table surveying

Last Answer : 1) It is used for sighting the objects to be located.  2) It is used for drawing the rays. 

Enlist different errors in compass surveying.

Description : Enlist different errors in compass surveying.

Last Answer : Various errors in compass surveying are classified asi) Instrumental errors. ii) Personal errors or observational errors iii) Errors caused due to external errors (natural errors) i) ... magnetic declination. c) Local attraction due to proximity of magnetic substances or magnetic field.

State the limitations of plane table surveying.

Description : State the limitations of plane table surveying.

Last Answer : 1) It is not suitable for work in wet climate 2) Several accessories are required to be carried hence possibility lost. 3) Replotting of survey work to different scale is difficult in absence of ... ) It is not intended for accurate work. 6) The plane table is essentially a tropical instrument.

Describe in brief resection method of plane table surveying.

Description : Describe in brief resection method of plane table surveying.

Last Answer : This method is used for establishing the instrument stations only. After fixing the stations, details are located either by radiation or intersection. The characteristic feature of resection is that the point ... of resection are (1)The Two Point Problem, and (2)Three Point Problem.

Describe in brief primary classification of surveying

Description : Describe in brief primary classification of surveying

Last Answer : Primary Classification Geodetic Survey The geodetic surveying is that type of surveying which takes into account the curvature of earth's surface. It is generally adopted for large area (more than ... large scale such as Bridges, Dams, Location and Construction of canals, highways, railways etc.

State the principles of surveying.

Description : State the principles of surveying. 

Last Answer : Main principles of surveying are: 1) To work from whole to part. 2) To locate a point at least by two independent processes

Write the uses of following survey instruments i) Ranging Rod ii) Pegs iii) Cross-staff iv) Plumb bob

Description : Write the uses of following survey instruments i) Ranging Rod ii) Pegs iii) Cross-staff iv) Plumb bob

Last Answer : i) Ranging Rod : Ranging rod are used for ranging. ii) Pegs : Pegs are used for marking the positions of stations or terminals points of survey lines. iii) Cross-staff : It is used ... It is also used for accurate centering of the surveying instruments like theodolite, compass, plane table etc. 

Write any four advantages of intersection method of plane tabling over radiation method of plane tabling.

Description : Write any four advantages of intersection method of plane tabling over radiation method of plane tabling.

Last Answer : Advantages of intersection method: 1. Interection method requires less ground distance measurement than radiation method. 2. By this method we can locate inaccessible points which cannot be ... to radiation method, intersection method eliminates undulation error, bisection error and plotting errors.

State any two uses of survey.

Description : State any two uses of survey.

Last Answer : Survey is useful for following: 1. To prepare a map or plan of the surveyed area for attaching it to legal documents. 2. To plot control points of boundries of locality 3. To determine ... . 5. To decide suitable gradient and camber of road depending on equal volume of cutting and filling.

State the uses of following instruments in survey: i)Cross staff ii) Chain iii) Pegs iv) Arrows

Description : State the uses of following instruments in survey: i)Cross staff ii) Chain iii) Pegs iv) Arrows

Last Answer : i) Cross-Staff: To set up perpendicular or right angle to given chain line OR to find foot of perpendicular from given object to a chain line. ii) Chain: Chains are used for measuring distances. iii) ... on survey lines. iv) Arrows : They are used to mark the end of each chain during chaining. 

Enlist uses of survey.

Description : Enlist uses of survey.

Last Answer : Uses of surveys. 1. To record relative positions of various points on the surface of earth. 2. Prepare plans and maps required for various works. 3. Layout of various engineering works. 4. Compute ... . 5. To prepare a topographic map 6. To prepare military map 7. To prepare archeological map

State four instruments used for setting offsets.

Description : State four instruments used for setting offsets.

Last Answer : i) Instruments used for setting offsets: 1)Chain 2)Tape 3) Open & French Cross Staff 4) Circular & Indian Optical Square  ii) Principle of optical square: The angle between the first incident ray and the last reflected ray is twice to that of angle between two mirrors in optical square.

State any four sources of errors in compass survey

Description : State any four sources of errors in compass survey 

Last Answer : Following are the sources of errors in compass survey1. Instrumental survey-  a. Needle may not be perfectly straight and might not be balanced properly over the station.  b. Graduations of the rings ... substances near the station.  b. Magnetic field may vary on account of some natural causes. 

Explain four types of meridians.

Description : Explain four types of meridians. 

Last Answer : 1. True meridian: -The line which is passing through geographical north or south pole and given point on the surface of earth is called as true meridian. 2. Magnetic meridian:-The direction indicated ... particular zone. These lines are termed as grid lines and the centre line as the grid meridian.

State any four types of offsets and define them.

Description : State any four types of offsets and define them. 

Last Answer : i) Long offset: If length of offset more than 15 m. ii) Short offset: If length of offset less than 15 m. iii) Perpendicular offset: Offset taken perpendicular to chain line. iv) Oblique offset: Offset not taken perpendicular to chain line.

State any four codes of signals in ranging with their meaning.

Description : State any four codes of signals in ranging with their meaning. 

Last Answer : In guiding the assistant into line, the surveyor should use following code of signals. Sr. No. Signal by the Surveyor  Action by the Assistant  1 Rapid sweeps i.e. up and down ... . 10 Both arms extended forward horizontally and then depressed. Fix the ranging rod.

Differentiate between plane and geodetic survey on any four points.

Description : Differentiate between plane and geodetic survey on any four points. 

Last Answer : Difference between Plane Surveying and Geodetic Surveying Points Plane Surveying Geodetic Surveying Definition Plane surveying is that type of surveying in which mean surface of ... Traditional survey equipment is used Precise and modern survey equipment are required

State four advantages of auto level.

Description : State four advantages of auto level.

Last Answer : Advantages of auto level: 1. More precise/accurate leveling can be done using these levels. 2. The telescope of this instrument needs only be approximately leveled over the tripod and then the ... it reduces operational fatigue. 5. Clear and erect image. 6. Light weight and compact.

State four advantages and four disadvantages of plane table survey

Description : State four advantages and four disadvantages of plane table survey

Last Answer : Advantages: 1. A field book is not required. 2. Errors of booking in field book avoided. 3. Errors of plotting can be readily checked. 4. Suitable in magnetic area. 5. Survey work with ... cannot be done in rainy season. 5. Difficult to re-plot as field notes are not available.

List any four accessories required for plane table survey.

Description : List any four accessories required for plane table survey.

Last Answer : 1. Plane table. 2. Plumbing U-fork. 3. Alidade. 4. Spirit level. 5. Trough compass. 6. Plumb bob.

Give any four code of signals used to direct assistant in ranging.

Description : Give any four code of signals used to direct assistant in ranging.

Last Answer : Sr. No. Signal Action 1 Rapid sweep with right hand Move right fast 2 Slow sweep with right hand Move right slowly 3 Right hand extended  Continue moving to ... head and moved down Correct position 8 Both hands forward and brought down Fix the point

Write errors in leveling and corresponding precaution

Description : Write errors in leveling and corresponding precaution

Last Answer : i) Instrument error with respect to bubble tube, leveling staff. 1.If bubble tube is sluggish it may apparently be in the center though the bubble line is not horizontal. Precaution - ... reading. Precaution- Leveling should be properly done by bringing the bubble of bubble tube at Centre.

Write the functions of the following components of prismatic compass i) Prism, ii) Lifting pin, iii) Prism cap, iv) Agate cap

Description : Write the functions of the following components of prismatic compass i) Prism, ii) Lifting pin, iii) Prism cap, iv) Agate cap

Last Answer : i) Prism: Reading printed on horizontal face of compass ring can be read from vertical position  ii) Lifting pin: When the instrument not in use the sight vane passes against the lifting pin which lift ... piece of hard glass provided on top of pivoted point, to reduce wear and tear of the point

Write three types of obstacles in chaining with examples.

Description : Write three types of obstacles in chaining with examples. 

Last Answer : 1. Obstacle which can be chained across but cannot be ranged across. , Examples: Hill Intervening , rising ground. 2. Obstacle which can be ranged but cannot be chained across., Example: ... . 3. Obstacle which can be neither be ranged across not be chained across, Example: Building obstruction

Draw sketch and write the procedure for setting offset to the left or right side of suvey line with open cross-staff.

Description : Draw sketch and write the procedure for setting offset to the left or right side of suvey line with open cross-staff.

Last Answer : Procedure for setting offset with open cross staff : 1. Keep the ranging rods at point P(fixed on survey line) and at point A1 approximately. 2. The cross staff with stadia rod is fixed ... can be fixed and perpendicular offset AB is said to be set to given survey line PQ in left side.

Write the code of signals used in ranging with respect to : i) Correct position ii) Fix the ranging rod iii) Vertical position of ranging rod iv) Move slowly to left of observer

Description : Write the code of signals used in ranging with respect to : i) Correct position ii) Fix the ranging rod iii) Vertical position of ranging rod iv) Move slowly to left of observer 

Last Answer : i) Correct position : Both hands above Head and then Brought Down ii) Fix the ranging rod : Both Arms extended forward horizontally and the hands depressed briskly iii) Vertical position of ranging rod : 1 ... and moved to the Left iv) Move slowly to left of observer : Slow sweeps with Left Hand

With neat sketch, write the procedure of measurement of fore bearing with compass.

Description : With neat sketch, write the procedure of measurement of fore bearing with compass.

Last Answer : For measuring fore bearing of line AB, i) Place the compass over station A, center and level it.  ii) Looking through eye slit towards object vane, bisect the ranging rod at station ... which coincides with horse hair at observer end. The observed reading is the fore bearing of line AB

What is changing face

Description : As used in survey

Last Answer : It's the operation of changing the face of telescope from left to right and vice versa.

Explain the temporary adjustments of prismatic compass.

Description : Explain the temporary adjustments of prismatic compass.

Last Answer : Temporary Adjustments of Prismatic Compass 1. Fixing the compass to the tripod The compass is fixed on a tripod by rotating screw head of tripod stand. 2. Centering the compass The prismatic compass ... prism is moved using focusing stud so that readings on graduated ring will be seen clearly. 

State the fundamental axes and mention their relationship for a dumpy level.

Description : State the fundamental axes and mention their relationship for a dumpy level.

Last Answer : Fundamental axis of dumpy level are as follows; i) The vertical axis ii) The axis of bubble tube iii) The line of collimation iv) The axis of the telescope Relationship between ... iii) Axis of telescope and line of collimation should coincide when dumpy level is correctly leveled.

Describe with neat sketch, the optical square and explain its principle.

Description : Describe with neat sketch, the optical square and explain its principle.

Last Answer : Principal of optical square :- the angle between the first incident ray and the last reflected ray is twice the angle between the two mirrors OR If there are two plane mirrors whose reflecting surfaces ... is 450 while that between the first incident ray and last reflected ray is 900 .  

What consideration would you have while selecting survey stations and survey lines in a chain survey?

Description : What consideration would you have while selecting survey stations and survey lines in a chain survey?

Last Answer : Following points to be considered while selecting survey stations and survey lines 1) Main survey station should be mutually visible. 2) All triangles should be well conditioned. 3) The survey line should lie ... of the area so as to form the frame work of triangles on it to cover maximum area. 

What are offsets? How are they taken and recorded? Explain with sketch.

Description : What are offsets? How are they taken and recorded? Explain with sketch.

Last Answer : Offsets are lateral measurement to the base line. They are Located by judgment if short And by instruments (optical square or cross staff) if long and measured by metallic tape and shown with their chainages on base line

Define fly leveling and profile leveling

Description : Define fly leveling and profile leveling

Last Answer : Fly Leveling adopted to transfer bench marks from one place to other .In this leveling only FS & BS are taken.  Profile leveling:- The operation in which the object is to determine the ... known distanced apart along a given line to obtained the accurate outline of the surface of the ground 

Define : 1) Bench mark 2) Datum surface 3) Line of collimation 4) Change Point

Description : Define : 1) Bench mark 2) Datum surface 3) Line of collimation 4) Change Point 

Last Answer : 1) Bench mark: - It is a fixed reference point of known elevation.. 2)Datum surface :-It is any arbitrarily assumed level surface from which vertical distance are measured 3) Line of collimation:- ... which the fore and back sights are taken.  It is the point denoting the shifting of the level.

State the situation where plane table is suitable.

Description : State the situation where plane table is suitable. 

Last Answer : 1) It is most suitable for preparing small scale maps 2) It is suitable in magnetic are where compass survey is not reliable 3) It is most suitable for filling in details between stations fixed by triangulation 4) It is suitable where accuracy is not required.

How would you detect presence of local attraction at a place ?

Description : How would you detect presence of local attraction at a place ?

Last Answer : The presence of local attraction may be detected by finding difference of FB & BB of the line. If the fore bearing and back bearing difference is 1800 then there is no local attraction at both ... difference is not equal to 1800 then there is local attraction at both or any one station. 

Define: WCB and Quadrantal Bearing system

Description : Define: WCB and Quadrantal Bearing system

Last Answer : Ans.: 1)WCB:-In this system the bearing of a line is always measured clockwise for the north point of the reference meridian towards the line round the circle the angle thus measured is called ... the bearing of a line is measured clockwise from the north point or south point whichever is nearest .