Define ‘ Fore bearing ’ & ‘ back bearing ’ of line with a neat sketch

1 Answer

Answer :

Fore bearing : The bearing of line observed in the direction of progress of survey is called fore bearing of the line. Bearing of line AB is observed at ‘A’ towards ‘B’ is called as fore bearing of the line ‘AB ‘

Back bearing : The bearing of line observed in opposite direction of the progress of survey is called back bearing of the line. The bearing observed at ‘B’ towards ‘A’ is called as back bearing of the line ‘AB’

image  

Related questions

Description : With neat sketch, write the procedure of measurement of fore bearing with compass.

Last Answer : For measuring fore bearing of line AB, i) Place the compass over station A, center and level it.  ii) Looking through eye slit towards object vane, bisect the ranging rod at station ... which coincides with horse hair at observer end. The observed reading is the fore bearing of line AB

Description : Define- 1. Whole circle bearing 2. Reduced bearing 3. Fore bearing 4. Back bearing

Last Answer : 1.Whole circle bearing-  The bearing measures only in the clockwise direction from meridian or north direction is known as whole circle bearing. 2.Reduced bearing  The bearing measures with ... bearing  The bearing observed in the direction of opposite of survey is called fore bearing. 

Description : Define the terms - dip of needle, magnetic bearing, fore bearing and back bearing.

Last Answer : Dip of needle: It is downward inclination or small angle made by freely suspended magnetic needle with the horizontal. Magnetic bearing: Magnetic bearing of a survey line is the horizontal angle ... of line measured in backward direction or opposite direction of survey, is known as back bearing.

Description : Define the terms i) Fore Bearing, ii) Open traverse, iii) Closing error, iv) Reduced bearing

Last Answer : i) Fore bearing : The bearing observed in the direction of progress of survey in clockwise manner is called fore bearing  ii) Open traverse : When the first and last survey lines does ... north or south direction in clockwise or anticlockwise manner is known as reduced or quadrantal bearing. 

Description : Find the back bearing of the following lines having fore bearing as given below: (i) PQ = N 55° 0' E (ii) EF == 280° 0' (iii) CD = S 58° 30' W (iv) OM= 180° 0'

Last Answer : i) F.B OF PQ = N 55°0 ’ E  B.B Of PQ = S 55°0 ’W  ii) F.B. Of EF = 280°0 ’   B.B OF EF = F.B -180°= 280°0 ’ -180° = 100°0 ’  iii) F.B OF CD = S 58°30’W  B.B OF CD = N 58°30’ E  iv) F.B OF GH = 180°  B.B OF GH = F.B -180°=180°-180°= 0°

Description : Define base line and check line with neat sketch. 

Last Answer : 1)Base Line : The longest line running roughly through the middle of the area to be surveyed is known as base line 2) Check line: The line joining the apex of a triangle to some fixed point on the ... A line joining some fixed point on any two sides of a triangle is known as check line. 

Description : Define the following: (i) Height of instrument (i) Back sight (iii) Fore sight (iv) Axis of bubble tube

Last Answer : i. Height of instrument: It is the reduced level of line of collimation when the leveling instrument is properly leveled. It is obtained by adding the BS reading to RL of bench mark or change point on which the ... when the bubble is at the center of its run i.e. at middle point of the tube.

Description : Describe in brief with neat sketch: i) Base line ii) Check line

Last Answer : i) Base line:  Base line is generally the longest line running roughly through the middle of the area. It is laid on a level ground as far as possible. The whole frame work is built upon this line. ... on the opposite side or a line joining some fixed point on any two sides of the triangle. 

Description : Describe with neat sketch, the optical square and explain its principle.

Last Answer : Principal of optical square :- the angle between the first incident ray and the last reflected ray is twice the angle between the two mirrors OR If there are two plane mirrors whose reflecting surfaces ... is 450 while that between the first incident ray and last reflected ray is 900 .  

Description : Draw a neat lebelled sketch of optical square. Explain its working.

Last Answer : Working of optical square1. Optical square works on principle of optical square to set perpendicular offset 2. Keep ranging rods at point B and C as shown in fig. 3. Observe the ... matched each other point D can be marked on ground and distance CD is measured as perpendicular offset.

Description : Draw a neat sketch of an arrow with dimensions.

Last Answer :  neat sketch of an arrow with dimensions

Description : Draw a neat labeled sketch of 30m chain.

Last Answer : neat labeled sketch of 30m chain

Description : Explain the radiation method of plane table survey with neat sketch. 

Last Answer : This method is used when all the points to be plotted are visible from single instrument station. Steps are: 1. Select a suitable point P on the ground such that all the details are visible from it. 2. Center and ... , pc, pd, pe respectively. Join a, b, c, d, and e to give the outline.

Description : Explain dip of magnetic needle with neat sketch. 

Last Answer : i) The inclination of the magnetic needle with the horizontal is called as magnetic dip of the needle. ii) Ordinary needle if perfectly balanced on pivot, remains in horizontal position. But when the needle ... sliding weight is attached on the side of the needle which is at higher position.  

Description : Explain reciprocal ranging with neat sketch. 

Last Answer : Reciprocal ranging is done when ends of survey line are not intervisible due to hill intervening or ends of survey line are at far distance apart. Step wise procedure reciprocal ranging: 1. Let A and B be ... chained. 8. This method can also be used in ranging a line across a valley.  

Description : Explain the procedure for profile leveling with neat sketch. 

Last Answer : 1) Let PQR be the given line of section.   2) Mark point at 10 m intervals on this line. 3) Level is set up on a firm ground at a suitable point I1. 4) Temporary adjustment of level is done and B. ... and set up on firm ground at I2 as before. 10) B.S is taken on CP1 and new HI is calculated  

Description : Explain ‘Intersection Method’ of plane table surveying with neat sketch. Also give situation when intersection method is used.

Last Answer : 1. Lay out a base line AB and measure it and Plot a distance ab' on sheet using any scale. 2.Set up instrument at A' with a' over A' 3.Orient the table by placing alidade ... the case of the survey of mountainous country. 5. The only linear measurement required is that of a base line.

Description : Explain Fly Levelling with neat sketch. State situation under which fly levelling is needed.

Last Answer : Ans: When DifferentialLevelling is done in order to connect a bench mark to the starting point of the alignment of any project, it is called as fly levelling. Fly levelling is also done to connect ...  ii)if distance is more between two points.  iii)if there obstacles between the two points.  

Description : Explain indirect ranging with neat sketch

Last Answer : Step wise procedure indirect ranging i.e. reciprocal ranging- Let A and B be the two station with rising ground or a hill intervening between them even i)Select any two intermediate station say M1 and N1 ... there position will be changed until finally they are both on the line A B exactly.  

Description : Explain with neat sketch the procedure of radiation method of plane tabling.

Last Answer : 1. The table is set at suitable station e.g. P from where all stations can be sighted and measured. 2. After centering and leveling, mark station P as P' on sheet. 3. Suppose stations A, B, C, and D are ... marked as pa. 5. Similarly station B, C and D are bisected and marked as b, c and d.

Description : Explain with neat sketch graphical adjustment of closing error.

Last Answer : Procedure: 1. Plot the traverse e.g. A'BCDEA to suitable scale and obtain magnitude and direction of closing error. 2. Draw a straight line A'BCDEA to some suitable scale representing the ... plotted points and locate new position of station points to give correct traverse A'B'C'D'E'A'.

Description : With neat sketch, explain the included angle method of plotting compass traverse. 

Last Answer : 1. Calculate all included angles of the traverse from observed bearings of the lines. e.g. <A, <B, <C, <D, <E  2. Check sum of included angles as equal to ( ... coincide with starting station (in case of closed traverse). If there is closing error, it needs to be corrected. 

Description : Draw a neat sketch of optical square. Explain its working.

Last Answer : Optical Square: Working: The optical square consists of circular box 50 mm in diameter, 12.5 mm in depth. The box has three slits as A,B, and C. bb' is horizon glass, half silvered i.e ... the point on the chain line where the offset can be dropped to meet point J as shown in fig.  

Description : Explain with neat sketch the procedure of reciprocal ranging.

Last Answer : Reciprocal ranging / Indirect ranging Procedure: Let A and B be two survey stations. They are not mutually visible due to high ground between them. Let two assistant stands at M1 and N1 as ... and N1 which are nearer to line AB. Repeat same process until points M and N are established. 

Description : Explain with neat sketch method of stepping of chaining on sloping ground.

Last Answer : Procedure : To measure the horizontal distance between points A & B on sloping ground following steps should be followed ( Refer above figure.) 1. Starting from point A, the chain is unfolded and ... . Finally calculate total chained distance as d(AB) = d(AP1) + d(P2P3) + d(P4P5)

Description : Draw a neat sketch of prismatic compass and label its component parts

Last Answer : Sketch of prismatic compass and label its component parts

Description : Explain principle of optical square with neat sketch.

Last Answer : Principle of optical square :- The angle between the first incident ray and the last reflected ray is twice the angle between the two mirrors In the case of optical square the angle between the mirrors is 45° while that between the first incident ray and last reflected ray is 90°.  

Description : Explain the process of chaining on sloping ground by stepping method with neat sketch.

Last Answer : The procedure to measure horizontal distance between the points A and B on sloping ground is as follows. 1. Two persons-leader and follower are required for chaining. 2. The follower holds the end of chain at A. The leader goes ... between A and b L = AM, + MN' + NO' + OP' + PQ' + QB'

Description : Explain reciprocal levelling with neat sketch. 

Last Answer : Reciprocal levelling is adopted i) To find the difference in level accurately Between the two points considerably apart. ii) When it is not possible to set up the level in between the two points ... true difference is equal to the mean of the two apparent differences of level between A and B 

Description : Differentiate between simple levelling and differential levelling with neat sketch. 

Last Answer : S.N Simple Levelling Differential levelling 1 Instrument is not shifted till the end of survey work.  Instrument is shifted as per requirements. 2 In this difference in elevation between ... elevation between two points is more or any obstacle between them. 4

Description : Define: WCB and Quadrantal Bearing system

Last Answer : Ans.: 1)WCB:-In this system the bearing of a line is always measured clockwise for the north point of the reference meridian towards the line round the circle the angle thus measured is called ... the bearing of a line is measured clockwise from the north point or south point whichever is nearest .

Description : Define true bearing and magnetic bearing.

Last Answer : 1. True bearing – (i) The angle between true meridian or geographical north and any line known as true bearing. 2.Magnetic bearing-(i)The angle between magnetic meridian and any line is known as magnetic bearing.

Description : Define: i) W.C.B. ii) Reduced Bearing

Last Answer : i)Whole circle bearing: The bearing measures only in the clockwise direction from meridian or north direction is known as whole circle bearing.   ii) Reduced bearing: The bearing measured ... north or south direction in clockwise or anticlockwise manner is known as reduced or quadrant bearing 

Description : Draw sketch and write the procedure for setting offset to the left or right side of suvey line with open cross-staff.

Last Answer : Procedure for setting offset with open cross staff : 1. Keep the ranging rods at point P(fixed on survey line) and at point A1 approximately. 2. The cross staff with stadia rod is fixed ... can be fixed and perpendicular offset AB is said to be set to given survey line PQ in left side.

Description : Back bearing of a line is equal to (A) Fore bearing ± 90° (B) Fore bearing ± 180° (C) Fore bearing ± 360° (D) Fore bearing ± 270°

Last Answer : (B) Fore bearing ± 180°

Description : Describe quadrantal bearing system. State the purpose it is used. 

Last Answer : Quadrantal Bearing - 1. The magnetic bearing of line measured clockwise or anticlockwise from north or south pole whichever is nearer. 2. These bearings are also called as reduced bearings. 3. ... lines in a closed traverse. 2. It is used to calculate back bearing for respective quadrants.

Description : Differentiate between reduced bearing and whole circle bearing

Last Answer : Quadrantal Bearing/Reduced Bearing Whole Circle Bearing The horizontal angle made by a line with the magnetic north or south (whichever is closer from the line) in the eastward or westward direction ... from 0° to 90°  The value of the whole circle bearing varies from 0° to 360° 

Description : What are offsets? How are they taken and recorded? Explain with sketch.

Last Answer : Offsets are lateral measurement to the base line. They are Located by judgment if short And by instruments (optical square or cross staff) if long and measured by metallic tape and shown with their chainages on base line

Description : Draw a sketch and explain how to find height of chajja or slab using dumpy level.

Last Answer : Explanation : 1. First the back sight reading is taken on floor level whose RL is known to us; from which RL of instrument axis can be find out by adding RL of BM and BS reading. 2. Now ... staff reading. 4. Finally height of chajja is calculated as RL of slab bottom -  RL of floor top.

Description : Draw sketch and explain method of traversing of plane table surveying. 

Last Answer : Procedure: 1.Set plane table over station A use plumbing fork for transferring station point from ground on sheet. Draw the direction of magnetic meridian with the help of compass. 2. With the ... scale Similarly, the table can be set at other successive station and traverse is completed.

Description : Draw the sketch of chain triangulation and label different lines.

Last Answer : AB – Base line AC, CD, DE, AE, EB - main survey lines DD’ – Check line. ab – Tie line.

Description : Draw labeled sketch of prismatic compass.

Last Answer : Sketch of prismatic compass :

Description : Draw sketch of optical square and state its principle.

Last Answer : The optical square is an instrument used to set perpendicular offset on the chain line. The optical square works on the principle of optics. Principle of optical square: The angle between the incident ray and reflected ray is twice the angle between mirrors.

Description : Explain Direct method of chaining on sloping ground with neat skeetch. 

Last Answer : While chaining on sloping ground, the horizontal distances can be computed by direct method i.e. By stepping. By stepping: It consist in measuring the distance in small horizontal lengths (e.g.L1). Let ... is continued in the correct line with point B. Then length of line AB=L1 +L2 +L3+L4

Description : Define the terms - Foresight, back sight, intermediate sight and change point.

Last Answer : 1. Fore sight: It is the last staff reading from any set up of the leveling instrument and indicates the shifting of the instrument or end of leveling work. 2. Back sight: It is the first staff reading ... point fore sight is taken from one set up and a back sight is taken from the nest set up. 

Description : Define : 1) Bench mark 2) Datum surface 3) Line of collimation 4) Change Point 

Last Answer : 1) Bench mark: - It is a fixed reference point of known elevation.. 2)Datum surface :-It is any arbitrarily assumed level surface from which vertical distance are measured 3) Line of collimation:- ... which the fore and back sights are taken.  It is the point denoting the shifting of the level.

Description : Define horizontal line and vertical line.

Last Answer : Horizontal line : A straight line tangential to the level line and perpendicular to the plumb line is called horizontal line.  Vertical line : A line perpendicular to horizontal line and coinciding plumb line is known as vertical line

Description : Define: i) Level Line, ii) Horizontal Line, iii) Vertical Line iv) Bench Mark. 

Last Answer : j) Level Line: It is line lying in a level surface; it is therefore, normal to the plumb line at all points. ii) Horizontal Line: It is a straight line tangential to the level line at a ... RL determined with reference to the datum line. They serve as reference points for finding RL of new points. 

Description : Define the term – base line and check line.

Last Answer : Base line: Base line is generally the longest line running roughly through the middle of the area. It is laid on a level ground as far as possible. The whole frame work is built upon this line. ... point on the opposite side or a line joining some fixed point on any two sides of the triangle.

Description : Define the term: (1) Level surface (2) Line of collimation

Last Answer : Level surface: It is a surface parallel to the mean spheroidal surface of the earth. It is normal to the direction of plumb line at all points. The surface of still water is an example of level ... to the optical center of object glass and its continuation. It is also called as line of sight.