If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be?

If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be?
by

1 Answer

Answer :

If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be a voltage source.

by

Related questions

As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100.

Description : As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is A) 25 A B) 50 A C) 100 A D) 200A

Last Answer : As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is 50 A

A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms

Description : A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms

Last Answer : ANSWER: W -- 25 OHMS

If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

Description : If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

Last Answer : If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

Consider the star network shown in figure. The resistance between terminals A and B with C open is 6 ohms,

Description : Consider the star network shown in figure. The resistance between terminals A and B with C open is 6 ohms, between terminals B and C withAopen is 11 ohms and between terminals C andAwith B open is 9 ohms. Then RA, RB, RC respectively is 

Last Answer : Consider the star network shown in figure. The resistance between terminals A and B with C open is 6 ohms, between terminals B and C withAopen is 11 ohms and between terminals C andAwith B open is 9 ohms. Then RA, RB, RC respectively is  2, 4,7

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is ...

Description : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

Last Answer : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is 150 W

24 cells of emf `1.5 V` each having internal resistance of 1 ohm are connected to an external resistance of `1.5` ohms. To get maximum current,

Description : 24 cells of emf `1.5 V` each having internal resistance of 1 ohm are connected to an external resistance of `1.5` ohms. To get maximum current,

Last Answer : 24 cells of emf `1.5 V` each having internal resistance of 1 ohm are connected to an external ... in series and 4 such rows are connected in parallel

Two resistance wires on joining in parallel the resultant resistance is ohms `(6)/(5)` ohms. One of the wire breaks, the effective resistance is 2 ohm

Description : Two resistance wires on joining in parallel the resultant resistance is ohms `(6)/(5)` ohms. One of the wire breaks, the effective resistance is 2 ohm

Last Answer : Two resistance wires on joining in parallel the resultant resistance is ohms `(6)/(5)` ohms. One of the wire ... ` C. `(6)/(5)Omega` D. `3Omega`

Prior to taking a resistance reading with a volt-ohm-milliammeter, the 'zero' setting must be adjusted. After clipping the two leads together, you find the adjustment knob will not return the pointer to 'zero'. This is most likely an indication of ______ A. an improper resistance range setting B. weak batteries C. a faulty zero ohms knob D. a faulty meter movement

Description : Prior to taking a resistance reading with a volt-ohm-milliammeter, the 'zero' setting must be adjusted. After clipping the two leads together, you find the adjustment knob will not return the pointer ... range setting B. weak batteries C. a faulty zero ohms knob D. a faulty meter movement

Last Answer : Answer: B

If PN junction is forward biased its resistance is (a) Zero (b) Infinity (c) A few ohm (d) A few kilo ohms

Description : If PN junction is forward biased its resistance is (a) Zero (b) Infinity (c) A few ohm (d) A few kilo ohms

Last Answer : c) A few ohm

A circuit has a resistance of 200 ohms. The resistance of the circuit can be reduced to 120 ohms by adding which of the following to the circuit. w) 80 ohm resistor in series x) 150 ohm resistor in parallel y) 240 ohm resistor in series z) 300 ohm resistor in parallel

Description : A circuit has a resistance of 200 ohms. The resistance of the circuit can be reduced to 120 ohms by adding which of the following to the circuit. w) 80 ohm resistor in series x) 150 ohm resistor in parallel y) 240 ohm resistor in series z) 300 ohm resistor in parallel

Last Answer : ANSWER: Z -- 300 OHM RESISTOR IN PARALLEL

A metal resistor has resistance of 10 ohm at 0°C and 11 ohms at 160°C, the temperature coefficient is

Last Answer : A metal resistor has resistance of 10 ohm at 0°C and 11 ohms at 160°C, the temperature coefficient is 0.000625 /°C.

The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Last Answer : Answer: D

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

"Any number of current sources in parallel may be replaced by a single current source whose current is ...

Description : "Any number of current sources in parallel may be replaced by a single current source whose current is the algebraic sum of individual source currents and source resistance is the parallel combination of individual source resistances". The above statement is associated with?

Last Answer : "Any number of current sources in parallel may be replaced by a single current source whose current is the algebraic sum of individual source currents and source ... parallel combination of individual source resistances". The above statement is associated with Millman's theorem.

"Maximum power output is obtained from a network when the load resistance...

Description : "Maximum power output is obtained from a network when the load resistance is equal to the output resistance of the network as seen from the terminals of the load". The above statement is associated with?

Last Answer : "Maximum power output is obtained from a network when the load resistance is equal to the output resistance of the network as seen from the terminals of the load". The above statement is associated with Maximum power transfer theorem.

For maximum transfer of power, internal resistance of the source should be?

Description : For maximum transfer of power, internal resistance of the source should be?

Last Answer : For maximum transfer of power, internal resistance of the source should be equal to load resistance.

For high efficiency of transfer of power, internal resistance of the source should be?

Description : For high efficiency of transfer of power, internal resistance of the source should be?

Last Answer : For high efficiency of transfer of power, internal resistance of the source should be less than the load resistance.

A wire whose resistance is 90 ohm is cut into 3 pieces of equal lengths which are then arranged in parallel. Calculate the resistance of the combinati

Description : A wire whose resistance is 90 ohm is cut into 3 pieces of equal lengths which are then arranged in parallel. Calculate the resistance of the combinati

Last Answer : A wire whose resistance is 90 ohm is cut into 3 pieces of equal lengths which are then ... in parallel. Calculate the resistance of the combination.

Two resistances are joined in parallel whose resultant is `6//8 ohm`. One of the resistance wire is broken and the effective resistance becomes `2 Ome

Description : Two resistances are joined in parallel whose resultant is `6//8 ohm`. One of the resistance wire is broken and the effective resistance becomes `2 Ome

Last Answer : Two resistances are joined in parallel whose resultant is `6//8 ohm`. One of the resistance wire is broken and the ... /5` B. 2 C. `6//5` D. 3

I have a 4 ohm bass guitar amplier. So I can only run one 4ohm speaker cabinet and not 2 correct? If I tried to use a 4ohm cabinet with a 8ohm cabinet with the 4 ohm amp would that still work or would the ohms become less than 4?

Description : I have a 4 ohm bass guitar amplier. So I can only run one 4ohm speaker cabinet and not 2 correct? If I tried to use a 4ohm cabinet with a 8ohm cabinet with the 4 ohm amp would that still work or would the ohms become less than 4?

Last Answer : From what I remember you can drive 8 ohms with a 4 ohm amp, but not the reverse.

In which year did G.S. Ohm formulate Ohm’s law?

Description : In which year did G.S. Ohm formulate Ohm’s law?

Last Answer : Answer: 1827.

How many ohms is equal to 1 international ohm ?

Description : How many ohms is equal to 1 international ohm ?

Last Answer : 1 international ohm = 1.000495 ohm.

When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage is being measured B. input impedance much less than the impedance across which the voltage is being measured C. sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Description : When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage ... sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Last Answer : Answer: A

A galvanometer with 20 ohms coil resistence has a full-scale deflection of 10 mA. A 0.02 ohm is placed across the meter to increase its rating capacity. What is the new full scale current for the meter?

Description : A galvanometer with 20 ohms coil resistence has a full-scale deflection of 10 mA. A 0.02 ohm is placed across the meter to increase its rating capacity. What is the new full scale current for the meter?

Last Answer : False.

The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from

Description : The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 ... .5 A from the same source will be  (A) 48.0% (B) 57.1% (C) 59.2% (D) 88.8%

Last Answer : The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be 48.0%

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is

Description : The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

Last Answer : The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is 11%

A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference...

Description : A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is

Last Answer : A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is 40 V.

The power supplied to a motor is six kilowatts at 120 volts. What is the impedance of the motor? A. 0.05 Ohms B. 0.50 Ohms C. 2.40 Ohms D. 24.00 Ohms

Description : The power supplied to a motor is six kilowatts at 120 volts. What is the impedance of the motor? A. 0.05 Ohms B. 0.50 Ohms C. 2.40 Ohms D. 24.00 Ohms

Last Answer : Answer: C

A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Last Answer : 50 volts.

A series combination of resistance 100 ohm and capacitance 50µf is connected in series to a 230 V, 50HZ supply. Calculate (i) Capacitive reactance (ii) Current (iii) Power factor (iv) Power consumed

Description : A series combination of resistance 100 ohm and capacitance 50µf is connected in series to a 230 V, 50HZ supply. Calculate (i) Capacitive reactance (ii) Current (iii) Power factor (iv) Power consumed 

Last Answer : For RC series circuit

ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Description : ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Last Answer : C. 174 K

The turns ratio required to match an 80 ohms source to a 320 ohms load is?

Description : The turns ratio required to match an 80 ohms source to a 320 ohms load is? A.80 B.20 C.4 D.2

Last Answer : c

What is the source of Ohm's resistance ?

Description : What is the source of Ohm's resistance ?

Last Answer : : Current flowing through a conductor at a constant temperature is proportional to the voltage across the two ends of the conductor. Or the current flowing through a conductor at a constant ... to the voltage difference between the two ends of that conductor and disproportionate to the resistance.

A lamp has a source voltage of 110 volts and a current of 0.9 amps. What is the resistance of the lamp? A. 0.008 ohms B. 0.08 ohms C. 12.22 ohms D. 122.22 ohms

Description : A lamp has a source voltage of 110 volts and a current of 0.9 amps. What is the resistance of the lamp? A. 0.008 ohms B. 0.08 ohms C. 12.22 ohms D. 122.22 ohms

Last Answer : Answer: D

What would be the power consumed in the combined parallel section of the circuit shown in the illustration if the source were 30 volts and the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Description : What would be the power consumed in the combined parallel section of the circuit shown in the illustration if the source were 30 volts and the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Last Answer : Answer: C

What power would be consumed by the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Description : What power would be consumed by the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Last Answer : Answer: D

What power would be consumed in EACH of the branch resistors of the circuit shown in the illustration if the source is 30 volts, the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Description : What power would be consumed in EACH of the branch resistors of the circuit shown in the illustration if the source is 30 volts, the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Last Answer : Answer: B

What would be the total power consumed in the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 10 watts B. 40 watts C. 45 watts D. 60 watts

Description : What would be the total power consumed in the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 10 watts B. 40 watts C. 45 watts D. 60 watts

Last Answer : Answer: D

What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: C

What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: B

What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps

Description : What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps

Last Answer : Answer: B

A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?

Description : A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?

Last Answer : (a) 160 ohms. (b) 480 ohms

A resistance of 3.3 M ohms is connected across a 500 V source. The resulting current is approximately?

Description : A resistance of 3.3 M ohms is connected across a 500 V source. The resulting current is approximately? A.15.1 μA B.151 μA C.66 mA D.660 mA

Last Answer : A

The scale of a galvanometer of resistance `100 ohms` contains 25 divisions. It gives a defelction of one division on passing a current of `4xx 10 ^(-4

Description : The scale of a galvanometer of resistance `100 ohms` contains 25 divisions. It gives a defelction of one division on passing a current of `4xx 10 ^(-4

Last Answer : The scale of a galvanometer of resistance `100 ohms` contains 25 divisions. It gives a defelction of one division ... is A. 150 B. 170 C. 110 D. 220

What is the resistance value indicated on the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'R'? EL-0047 A. 6.0 ohms B. 162.5 ohms C. 600 ohms D. 16,250 ohms

Description : What is the resistance value indicated on the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'R'? EL-0047 A. 6.0 ohms B. 162.5 ohms C. 600 ohms D. 16,250 ohms

Last Answer : Answer: C

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'Y'? EL-0047 A. 220 ohms B. 240 ohms C. 2,400 ohms D. 24,000 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'Y'? EL-0047 A. 220 ohms B. 240 ohms C. 2,400 ohms D. 24,000 ohms

Last Answer : Answer: C

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'A'? EL-0047 A. 10 ohms B. 100 ohms C. 200 ohms D. 1,000 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 1, and the needle is at the position indicated by the letter 'A'? EL-0047 A. 10 ohms B. 100 ohms C. 200 ohms D. 1,000 ohms

Last Answer : Answer: C

You are calibrating a multimeter using internal batteries to supply power for resistance measurements. However, you are unable to adjust the pointer to 'zero' using the adjustment knob. Therefore, you should _____________. A. replace the batteries in the instrument B. measure resistance by dividing the voltmeter indication by the ammeter indication C. set the pointer using a bridge D. change scales to the R X 100 scale and adjust using the 'zero ohms' adjusting knob

Description : You are calibrating a multimeter using internal batteries to supply power for resistance measurements. However, you are unable to adjust the pointer to 'zero' using the adjustment knob. Therefore, you should ... change scales to the R X 100 scale and adjust using the 'zero ohms' adjusting knob

Last Answer : Answer: A

What is the diameter of a copper wire to be used in a 16 km loop with a dc loop resistance of 100 ohms/km? A. 0.108 cm B. 1.082 cm C. 0.017 cm D. 0.0465 cm

Description : What is the diameter of a copper wire to be used in a 16 km loop with a dc loop resistance of 100 ohms/km? A. 0.108 cm B. 1.082 cm C. 0.017 cm D. 0.0465 cm

Last Answer : D. 0.0465 cm