The turns ratio required to match an 80 ohms source to a 320 ohms load is?

The turns ratio required to match an 80 ohms source to a 320 ohms load is?

A.80

B.20

C.4

D.2
by

2 Answers

Answer :

The turns ratio required to match an 80 ohms source to a 320 ohms load is?

A.80

B.20

C.4

D.2

by

Answer :

c
by

Related questions

If an incandescent lamp of 80 ohms resistance takes a current of 0.75 ampere, what voltage is

Description : If an incandescent lamp of 80 ohms resistance takes a current of 0.75 ampere, what voltage is required to light it? A.45 volts B.60 volts c.23 volts D.None of these

Last Answer : V=IR    = 80*0.75     = 60 volts

A resistance of 3.3 M ohms is connected across a 500 V source. The resulting current is approximately?

Description : A resistance of 3.3 M ohms is connected across a 500 V source. The resulting current is approximately? A.15.1 μA B.151 μA C.66 mA D.660 mA

Last Answer : A

When the turns ratio of a transformer is 20 and the primary ac voltage is 12 V, the secondary voltage is?

Description : When the turns ratio of a transformer is 20 and the primary ac voltage is 12 V, the secondary voltage is? A.12 V B.120 V C.240 V D.2,400 V

Last Answer : When the turns ratio of a transformer is 20 and the primary ac voltage is 12 V, the secondary voltage is? A.12 V B.120 V C.240 V D.2,400 V

The turns ratio of a transformer having 200 primary turns and 1,200 secondary turns is?

Description : The turns ratio of a transformer having 200 primary turns and 1,200 secondary turns is? A.6 B.24 C.1.66 D.66

Last Answer : The turns ratio of a transformer having 200 primary turns and 1,200 secondary turns is? A.6 B.24 C.1.66 D.66

A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms

Description : A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms

Last Answer : ANSWER: W -- 25 OHMS

In order to get maximum power transfer from a capacitive source, the load must?

Description : In order to get maximum power transfer from a capacitive source, the load must? A.have a capacitive reactance equal to circuit resistance B.have an impedance that is the complex conjugate of the source impedance C.be as capacitive as it is inductive D.none of the above

Last Answer : In order to get maximum power transfer from a capacitive source, the load must? A.have a capacitive reactance equal to circuit resistance B.have an impedance that is the complex conjugate of the source impedance C.be as capacitive as it is inductive D.none of the above

A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?

Description : A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?

Last Answer : (a) 160 ohms. (b) 480 ohms

How much voltage is needed to produce 2.5 A of current through a 200 ohms resistor?

Description : How much voltage is needed to produce 2.5 A of current through a 200 ohms resistor? A.50 V B.500 V C.80 V D.8 V

Last Answer : 500 V

When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is?

Description : When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is? A.14.4 V B.1.4 V C.100 V D.10 V

Last Answer : When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is? A.14.4 V B.1.4 V C.100 V D.10 V

Four amperes of current are measured through a 24 ohms resistor connected across a voltage

Description : Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce? A.960 V B.9.6 V C.96 V D.8 V

Last Answer : Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce? A.960 V B.9.6 V C.96 V D.8 V

If three wires of 3 ohms, 9 ohms and 5 ohms respectively are connected in series, what their

Description : If three wires of 3 ohms, 9 ohms and 5 ohms respectively are connected in series, what their resultant resistance? A.10 ohms B.12 ohms C.17 ohms D.5 ohms

Last Answer : If three wires of 3 ohms, 9 ohms and 5 ohms respectively are connected in series, what their resultant resistance? A.10 ohms B.12 ohms C.17 ohms D.5 ohms

What amount of current will flow through resistance of 10 ohms when it is connected across a

Description : What amount of current will flow through resistance of 10 ohms when it is connected across a potential difference of 20 volts? A.30 amperes B.5 amperes C.10 amperes D.2 amperes

Last Answer : 2 amperes

If the diameter of a conductor of 10 ohms is doubled, its new resistance would be?

Description : If the diameter of a conductor of 10 ohms is doubled, its new resistance would be? A.20 ohms B.5 ohms C.40 ohms D.2.5 ohms

Last Answer : 4

A certain transformer has 400 turns in the primary winding and 2,000 turns in the secondary

Description : A certain transformer has 400 turns in the primary winding and 2,000 turns in the secondary winding. The turns ratio is? A.0.2 B.0.4 C.5 D.25

Last Answer : A certain transformer has 400 turns in the primary winding and 2,000 turns in the secondary winding. The turns ratio is? A.0.2 B.0.4 C.5 D.25

If a transformer has 50 turns in the primary winding and 10 turns in the secondary winding,

Description : If a transformer has 50 turns in the primary winding and 10 turns in the secondary winding, what is the reflective resistance if the secondary load resistance is 250 ohms? A.250 ohms B.25 ohms C.6,250 ohms D.62,500 ohms

Last Answer : 6,250 ohms

The size of small stable RNA ranges from (A) 0–40 nucleotides (B) 40–80 nucleotides (C) 90–300 nucleotides (D) More than 320 nucleotides

Description : The size of small stable RNA ranges from (A) 0–40 nucleotides (B) 40–80 nucleotides (C) 90–300 nucleotides (D) More than 320 nucleotides

Last Answer : Answer : C

ECE Board Exam March 1996 What is the transmission rate of a system for transmitting the output of a microcomputer to a line printer operating at a speed of 30 lines/minute? Assume that the line printer has 8 bits of data per character and prints out 80 characters/line. A. 800 bps B. 400 bps C. 320 bps D. 640 bps

Description : ECE Board Exam March 1996 What is the transmission rate of a system for transmitting the output of a microcomputer to a line printer operating at a speed of 30 lines/minute? Assume that the line printer has 8 bits ... and prints out 80 characters/line. A. 800 bps B. 400 bps C. 320 bps D. 640 bps

Last Answer : C. 320 bps

How much area could be covered for giving one irrigation of 3" depth by a pumpset of one cusec output in the operation of 600 hours, if the water conveyance efficiency is 80 per cent ? (A) 180 acres (B) 320 acres (C) 240 acres (D) 160 acres (E) None of these

Description : How much area could be covered for giving one irrigation of 3" depth by a pumpset of one cusec output in the operation of 600 hours, if the water conveyance efficiency is 80 per cent ? (A) 180 acres (B) 320 acres (C) 240 acres (D) 160 acres (E) None of these

Last Answer : (C) 240 acres

Station A uses 32 byte packets to transmit messages to Station B using a sliding window protocol. The round trip delay between A and B is 80 milliseconds and the bottleneck bandwidth on the path between A and B is 128 kbps. What is the optimal window size that A should use? a. 20 b. 40 c. 160 d. 320

Description : Station A uses 32 byte packets to transmit messages to Station B using a sliding window protocol. The round trip delay between A and B is 80 milliseconds and the bottleneck bandwidth on the path between A and B ... What is the optimal window size that A should use? a. 20 b. 40 c. 160 d. 320

Last Answer : b. 40

A man on tour travels first 160 km at 64 km/hr and the next 160 km at 80 km/hr. The average speed for the first 320 km of the tour is: a) 35.55 km/hr b) 36 km/hr c) 71.11 km/hr d) 71 km/hr e) 69.69km/hr

Description : A man on tour travels first 160 km at 64 km/hr and the next 160 km at 80 km/hr. The average speed for the first 320 km of the tour is: a) 35.55 km/hr b) 36 km/hr c) 71.11 km/hr d) 71 km/hr e) 69.69km/hr

Last Answer : Total time taken = (160/64) + (160/80) = 9/2 hrs. Avg Speed – 320 × (2/9) km/hr = 71.11km/hr Answer: c)

What is the moment of inertia acting on a rectangle of width 15 mm and depth 40 mm about base by using theorem of parallel axes? a. 320 x 103 mm4 b. 300 x 103 mm4 c. 240 x 103 mm4 d. 80 x 103 mm

Description : What is the moment of inertia acting on a rectangle of width 15 mm and depth 40 mm about base by using theorem of parallel axes? a. 320 x 103 mm4 b. 300 x 103 mm4 c. 240 x 103 mm4 d. 80 x 103 mm

Last Answer : a. 320 x 103 mm4

What is the average level of cholesterol in an egg? a. 80 mg c. 240 mg b. 120 mg d. 320 mg

Description : What is the average level of cholesterol in an egg? a. 80 mg c. 240 mg b. 120 mg d. 320 mg

Last Answer : c. 240 mg

The world population growth rate at a certain reference year was 3.5%. Assuming exponential growth of population, after how many years, the population of the world would have increased by a factor 16 ? (A) ~ 80 years (B) ~ 40 years (C) ~ 160 years (D) ~ 320 years

Description : The world population growth rate at a certain reference year was 3.5%. Assuming exponential growth of population, after how many years, the population of the world would have increased by a factor 16 ? (A) ~ 80 years (B) ~ 40 years (C) ~ 160 years (D) ~ 320 years

Last Answer : Answer: A

If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be?

Description : If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be?

Last Answer : If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be a voltage source.

A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Description : A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Description : A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

A 60 Hz, 320 km lossless line has Bending end voltage 1.0 p.u, The receiving end voltage on no load is

Description : A 60 Hz, 320 km lossless line has Bending end voltage 1.0 p.u, The receiving end voltage on no load is?

Last Answer : A 60 Hz, 320 km lossless line has Bending end voltage 1.0 p.u, The receiving end voltage on no load is 1.088 p.u.

The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Last Answer : (a)1/2

A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the

Description : A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the figure. The magnetizing current drawn is 1A, and the secondary current is 1A. Ifcore losses and ... reactances are neglected, the primary current is  A)1.41A B)2A C) 2.24A D)3A

Last Answer : A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the figure. The magnetizing current drawn is 1A, and the secondary current is 1A. Ifcore losses and leakage reactances are neglected, the primary current is 2.24A

Assuming that the disk head is located initially at 32, find the number of disk moves required with FCFS if the disk queue of I/O block requests are 98, 37, 14, 124, 65, 67: (A) 310 (B) 324 (C) 320 (D) 321

Description : Assuming that the disk head is located initially at 32, find the number of disk moves required with FCFS if the disk queue of I/O block requests are 98, 37, 14, 124, 65, 67: (A) 310 (B) 324 (C) 320 (D) 321

Last Answer : (D) 321

If the Disk head is located initially at track 32, find the number of disk moves required with FCFS scheduling criteria if the disk queue of I/O blocks requests are: 98, 37, 14, 124, 65, 67 (A) 320 (B) 322 (C) 321 (D) 319

Description : If the Disk head is located initially at track 32, find the number of disk moves required with FCFS scheduling criteria if the disk queue of I/O blocks requests are: 98, 37, 14, 124, 65, 67 (A) 320 (B) 322 (C) 321 (D) 319

Last Answer : (C) 321

On a certain day, the ratio of the passenger in the 1st class and the second class travelling by train is 1:3. the ratio of the fares collected from each first class and second class passengers is 30:1. If the total amount collected from all the passengers is Rs 1,320. Find the amount in Rs, collected from the second class passengers. A) 240 B) 360 C) 480 D) 120 E) None

Description : On a certain day, the ratio of the passenger in the 1st class and the second class travelling by train is 1:3. the ratio of the fares collected from each first class and second class passengers is 30:1. If ... in Rs, collected from the second class passengers. A) 240 B) 360 C) 480 D) 120 E) None

Last Answer : Answer: D Let the number of passengers travelling by first class and second class be x and 3x respectively. Lets the fares collected from each of the first class and second class passengers be 30y and y ... 3xy=33xy=1320 xy=40. Total amount collected from the second class =3xy=3 40= Rs 120.

The monthly incomes of A and B are in the ratio 4:5, their expenses are in the ratio 5 : 6. If 'A' saves Rs.25 per month and 'B' saves Rs.50 per month, what are their respective incomes? A) Rs.400 and Rs.500 B) Rs.240 and Rs.300 C) Rs.320 and Rs.400 D) Rs.440 and Rs.550 E) NONE

Description : The monthly incomes of A and B are in the ratio 4:5, their expenses are in the ratio 5 : 6. If 'A' saves Rs.25 per month and 'B' saves Rs.50 per month, what are their respective incomes? A) Rs.400 and Rs.500 B) Rs.240 and Rs.300 C) Rs.320 and Rs.400 D) Rs.440 and Rs.550 E) NONE

Last Answer : Answer: A Let AA's income be = 4x AA's expenses, therefore = 4x–25 Let BB's income be = 5x BB's expenses, therefore = 5x–50 We know that the ratio of their expenses = 5:6 ⇒24x−150=25x−250 ⇒ Therefore, x=100 A's income =4x=400 and B's income =5x=500 

A constant load power means a uniform conversion of?

Description : A constant load power means a uniform conversion of? A.mechanical to electrical energy B.electrical to mechanical energy C.current to voltage D.voltage to current

Last Answer : A constant load power means a uniform conversion of? A.mechanical to electrical energy B.electrical to mechanical energy C.current to voltage D.voltage to current

Sparking occurs when a load is switched off because the circuit has high?

Description : Sparking occurs when a load is switched off because the circuit has high?

Last Answer : Sparking occurs when a load is switched off because the circuit has high inductance.

In a lamp load when more than one lamp are switched on the total resistance of the load?

Description : In a lamp load when more than one lamp are switched on the total resistance of the load?

Last Answer : In a lamp load when more than one lamp are switched on the total resistance of the load decreases.

In a solenoid valve system if the voltage on the coil is 118 VAC and a continuity test of the solenoid and coil measures 80 ohms yet the solenoid will not allow water flow the most likely cause of?

Description : In a solenoid valve system if the voltage on the coil is 118 VAC and a continuity test of the solenoid and coil measures 80 ohms yet the solenoid will not allow water flow the most likely cause of?

Last Answer : There could be more than one reasons. Applied voltage may not be118 volts. Solenoid valve may have been stuck mechanically.Solenoid coil could be faulty, partially short.

The reading at 'X' while on the R X 100 meter scale illustrated would be ______. EL-0047 A. 8 ohms B. 150 ohms C. 800 ohms D. 80,000 ohms

Description : The reading at 'X' while on the R X 100 meter scale illustrated would be ______. EL-0047 A. 8 ohms B. 150 ohms C. 800 ohms D. 80,000 ohms

Last Answer : Answer: C

When a bridge is used to measure resistance, what is the value of Rx if R1 equals 80 ohms, R2 equals 120 ohms, and R3 equals 280 ohms?

Description : When a bridge is used to measure resistance, what is the value of Rx if R1 equals 80 ohms, R2 equals 120 ohms, and R3 equals 280 ohms?

Last Answer : 420 ohms.

For an overhead line, the surge impedance is taken as (a) 20-30 ohms (b) 70—80 ohms (c) 100—200 ohms (d) 500—1000 ohms (e) none of the above

Description : For an overhead line, the surge impedance is taken as (a) 20-30 ohms (b) 70—80 ohms (c) 100—200 ohms (d) 500—1000 ohms (e) none of the above

Last Answer : (c) 100—200 ohms

A circuit has a resistance of 200 ohms. The resistance of the circuit can be reduced to 120 ohms by adding which of the following to the circuit. w) 80 ohm resistor in series x) 150 ohm resistor in parallel y) 240 ohm resistor in series z) 300 ohm resistor in parallel

Description : A circuit has a resistance of 200 ohms. The resistance of the circuit can be reduced to 120 ohms by adding which of the following to the circuit. w) 80 ohm resistor in series x) 150 ohm resistor in parallel y) 240 ohm resistor in series z) 300 ohm resistor in parallel

Last Answer : ANSWER: Z -- 300 OHM RESISTOR IN PARALLEL

How much resistance is needed to draw 17.6 mA from a 12 volt source?

Description : How much resistance is needed to draw 17.6 mA from a 12 volt source? A.212 ohms B.6.8 kohms C.68 ohms D.680 ohms

Last Answer : How much resistance is needed to draw 17.6 mA from a 12 volt source? A.212 ohms B.6.8 kohms C.68 ohms D.680 ohms

The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330

Description : The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330 ohms load. The turns ratio is 3:1. What is the secondary voltage? A.2 V B.20 V C.180 V D.18 V

Last Answer : The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330 ohms load. The turns ratio is 3:1. What is the secondary voltage? A.2 V B.20 V C.180 V D.18 V

Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor

Description : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

Last Answer : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

Approximately how many milliamperes of current flow through a circuit with a 40 V source and

Description : Approximately how many milliamperes of current flow through a circuit with a 40 V source and 6.8 k ohms of resistance? A.27.2 mA B.59 mA C.5.9 mA D.590 mA

Last Answer : Approximately how many milliamperes of current flow through a circuit with a 40 V source and 6.8 k ohms of resistance? A.27.2 mA B.59 mA C.5.9 mA D.590 mA

An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is

Description : An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately? A.385 ohms B.38.5ohms C.3.1 ohms D.31 ohms

Last Answer : 31ohns

Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Last Answer : Answer: Option C

How much resistance is required to limit the current from a 12 V battery to 3.6 mA?

Description : How much resistance is required to limit the current from a 12 V battery to 3.6 mA? A.3.3 k ohms B.33 k ohms C.2.2 k ohms D.22 k ohms

Last Answer : How much resistance is required to limit the current from a 12 V battery to 3.6 mA? A.3.3 k ohms B.33 k ohms C.2.2 k ohms D.22 k ohms

In a single threaded worm and worm wheel the number of teeth on the worm wheel is 80. The diameter of the effort wheel is 12 cm and that of load drum is 8 cm. The velocity ratio will be a.60 b.45 c.120 d.107 dynes e.90

Description : In a single threaded worm and worm wheel the number of teeth on the worm wheel is 80. The diameter of the effort wheel is 12 cm and that of load drum is 8 cm. The velocity ratio will be a.60 b.45 c.120 d.107 dynes e.90

Last Answer : c. 120

A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Description : A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Last Answer : Solution :