Describe the points to be considered for road safety.

1 Answer

Answer :

Points to be considered for road safety are: 1) The road should be designed to proper standards, built to the correct specifications & maintained adequately. 2) The safe speed at which the Vehicle can negotiate a curve depends on the Radius of curvature of the curve. Sharp curves permit low speeds & large Radii curves cater high design speeds. 3) For a Vehicle to negotiate any curve at the desired speed, the road should have adequate super elevation. Deficiency of super elevation can cause serious Accidents. 4) The Minimum carriageway width for two-way road should be 7m to cater for 2 lanes of Traffic. 5) Properly designed & Maintained Road signs inform the driver of need for caution & can avoid accident. 6) Guard Rails and safety barriers prevent vehicles form going off the Roadway in the event of loss of control. 7) Improved visibility & good street lighting also reduces the number of Accidents to about 30%. 8) Channelization Islands Reduces the number of Collision points & hence promotes safety.

Related questions

Description : Write the points to be considered while erecting road signs.

Last Answer : The points to be considered while erecting road signs are: i) The signs should be placed on the left hand side of the road. ii) Road sign should normally be placed at right angles to the pavement and ... of the sign adjacent to highway, should not be less than 60cm away from the edge of the kerb. 

Description : Write the essential road characteristics to be considered in traffic engineering.

Last Answer : The essential road characteristics to be considered in traffic engineering are as follows: i) Gradient ii) Curve of road iii) Design speed iv) Friction between road and tyre surface

Description : Describe the procedure of traffic volume count on any road intersection. Also write the method of representation of traffic volume count data.

Last Answer : The procedure of traffic volume count can be done by any of the methods below: a) Manual counting b) Automatic recorders c) Moving car method a) Manual counting: In this method, the ... Volume flow diagrams at intersection iii) Variation charts iv) Traffic flow map v) Traffic trend charts

Description : Describe the factors affecting visibility of road at night time.

Last Answer : Factors affecting visibility of road at night time are: i)Amount and distribution of light: The distribution should be downwards so that high percentage of light is utilized for illuminating the pavement ... : To perceive an object, the physical and mental condition of driver plays a vital role.

Description : Discuss the legislation and law enforcement education in road accident studies.

Last Answer : Various Legislative Measures have been adopted like 1. Age limit of drivers 2. Penalties of fine on License for careless driving. 3. Enable Police to check the drivers for the drunkenness. ... for children. 4. Posters exhibiting serious results due to carelessness of road users can be useful.

Description : Discuss the method of spot speed studies on a road section

Last Answer : i) The simplest method of finding spot speed is by using endoscope. ii) The observer is stationed on one side of the road and starts a stopwatch when a vehicle crosses that section iii) An endoscope is ... of vehicles in that group on Y axis. This graph is called Speed distribution curve.

Description : Suggest the preventive measures to prevent road accidents.

Last Answer : Following measure/remedies are suggested to prevent road accidents: - Engineering Aids/Measures 1. By checking and Redesigning the Road geometrics, if necessary (sight distance, width of ... safety should be displayed - This knowledge should also be given to children, schools, parents

Description : Write the objectives of road arboriculture.

Last Answer : The objectives of road arboriculture are: i) To provide attractive landscape on the roadside. ii) To provide shades to the road user. iii) To interrupt the annoying sound waves and fumes from road ... We get fruit bearing trees and timber. viii) To decrease the impact of air pollution and dust.

Description : Write the types of signals to be provided on road.

Last Answer : The types of traffic signals to be provided are: i) Traffic Control Signals: a) Fixed time signal b) Manually operated signal c) Traffic actuated signal ii) Pedestrian signal iii) Special traffic signal

Description : Describe the necessity of origin and destination study.

Last Answer : Necessities of origin and destination study are: i) To judge the adequacy of existing routes and to use in planning new network of roads. ii) To plan transportation system and mass transit ... transport. viii) To establish design standards for the roads, bridges and culverts along the route.

Description : Explain with sketch: i) Rotary island ii) Channelizing island

Last Answer : a) Rotary Island: A traffic island constructed in the center of an intersection to force the movement of traffic in the clockwise direction is called Rotary Island. They are constructed ... shape of channelizing island will very much depend upon the layout and dimensions of the intersection.

Description : Explain the method of recording and reporting of an accident.

Last Answer : There are three steps involved: I) Collection of Accident data II) Accident Report III) Accident Records I) Collection of Accident data: a) General: Date, Time, Persons involved in ... are most useful to compare the Accident pattern before & after the Remedial Measures have been taken.

Description : Discuss the factors affecting selection of type of roadside trees.

Last Answer : Factors affecting selection of type of roadside trees are: i) Trees selected should be such that it provides a large and dense crown with beautiful and uniform shape. ii) Trees must be able to ... pattern etc. viii) Trees like Gulmohar, Ashoka can be planted for landscaping on highways.

Description : Enumerate the advantages and disadvantages of grade separated intersections

Last Answer : Advantages: i) Grade separated intersections provide maximum facility to the crossing traffic and avoid accident while crossing. ii) They provide increased safety for turning traffic. By introducing ... They may cause undesirable crests and sags in vertical alignment in flat or plain areas. 

Description : Compare the fixed time signals with manually operated signals.

Last Answer : Fixed time signals Manually operated signals 1. These are pre-time signals which are set to repeat regularly a cycle of red, yellow and green lights. 1. These signals are those in which timings ... routes changes during the day.  4. Initial cost is high.  4. Less expensive.

Description : Explain the uses of various carriage way markings.

Last Answer : The uses of various carriage way markings are: i) Center line marking: They are provided on two way roads to separate the streams of traffic moving in opposite direction. ii) Traffic ... the form of monument within the carriageway so as to prevent vehicles from colliding with the obstruction.

Description : Classify the traffic markings.

Last Answer : Traffic markings are follows: 1. Carriageway marking or pavement marking 2. Kerb marking 3. Object marking 4. Reflector marking or unit marking

Description : List out the factors affecting reaction time of driver. 

Last Answer : The factors affecting reaction time of driver are: a) Physical and Psychological characteristics of driver b) Type of the problem involved c) Environmental condition d) Temporary factors ( Eg: Motive of trip, Travel speed, Fatigue)

Description : List out the traffic controlling devices.

Last Answer : The types of traffic controlling devices are as follows: i) Traffic signs or Road signs ii) Traffic markings or Road markings iii) Traffic signals iv) Traffic Islands

Description : Give the purposes of traffic studies.

Last Answer : i) To collect the data about type and volume of traffic at present and to estimate the same that the road is expected to carry in near future. ii) To determine the existing facilities such as ... traffic survey relating to accidents. vii) To estimate the amount of road taxes that can be levied.

Description : Define Traffic engineering

Last Answer : The phase of highway engineering which deals with planning and geometrical design of Roads, streets, adjoining lands with traffic operations for safe convenient and economic transportation of persons and goods is called as Traffic Engineering.

Description : Road safety measures: Is this a good or a bad idea? (see details)

Last Answer : I agree with you. I can see it causing drivers to slam on their breaks and I could also see it desensitizing drivers to children actually being in the streets. I would imagine after driving over it ... it would effect their reaction time (causing them to hit the child instead of being able to stop).

Description : Why don't bicyclists follow the rules of the road for other people's safety?

Last Answer : I’ll get my cyclist boyfriend to answer this later.

Description : Stopping distance of vehicles : When brakes are applied to a moving vehicle, the distance it travels before stopping is called stopping distance. It is an important factor for road safety and depends on ... the brake with the deceleration of 5m/s2. Find the stopping distance of the car -Science

Last Answer : Here u=72 km/hr = 72×10003600m/s=2072×10003600m/s=20 m/s , v=0 a= -5 m/s2 Now using the relation v2=u2+2asv2=u2+2as 0=(20)2+2×(−5)×s0=(20)2+2×(−5)×s s=40ms=40m

Description : Which decade is celebrated as decade of Action for road safety? -General Knowledge

Last Answer : The answer is '2011-2020'

Description : Which decade is celebrated as decade of Action for road safety? -General Knowledge

Last Answer : answer:

Description : (a) Mobilisation of city dwellers (b) Darkness around Sunrise Apartments (c) Road safety in the colony (d) Concern about night accidents

Last Answer : (b) Darkness around Sunrise Apartments

Description : Which decade is celebrated as decade of Action for road safety?

Last Answer : 2011-2020

Description : A radio communications service use in radio regulation between specified fixed points provided primarily for the safety of air navigation and for the regular efficient and economical air transport ... operation service B. Space service C. Aeronautical mobile service D. Aeronautical fixed service

Last Answer : D. Aeronautical fixed service

Description : At a road junction, 16 cross conflict points are severe, if (A) Both are one-way roads (B) Both are two-way roads (C) One is two-way road and other is one-way road (D) None of these

Last Answer : Answer: Option B

Description : At a road junction, 7 cross conflict points are severe if (A) Both are one-way roads (B) Both are two-way roads (C) One is two-way road and other is one-way road (D) None of these

Last Answer : Answer: Option C

Description : Three points A, B and C 500 m apart on a straight road have 500 m, 505 m and 510 m as their reduced levels. The road is said to have (A) No gradient between A and C (B) A positive gradient between A and C (C) A negative gradient between A and C (D) A negative gradient between A and B

Last Answer : Answer: Option D

Description : The reduced levels of points, 30 metres apart along the longitudinal section of a road portion between chainages 5 and 9 are shown in the given figure. If there is a uniform up-gradient of the road 120 in 1, the chainage ... 15) chains (B) (6 + 12) chains (C) (6 + 18) chains (D) None of these

Last Answer : (B) (6 + 12) chains

Description : The distance between the towns is only 30 kms as the crow flies. (1) when measured in a straight line (2) when measured in a random manner (3) when measured between the two highest points (4) when the curves of the road are included in the measurement

Last Answer : 1) when measured in a straight line

Description : Which one is a major environmental and safety hazard for the people in hilly areas in Tripura which can be considered as “cancer of hill slopes” a) Flood (b) Landslide (c) Earthquake (d) Desertification

Last Answer : (b) Landslide

Description : Why is road transport in India considered more useful than rail transport ? State two reasons in support of your answer. -Geography

Last Answer : Road transport is more useful than tail transport as : (i) Door to door service is most attractive feature of road transport. (ii) They can be constructed in hilly areas as they can negotiate sharp bends and slopes.

Description : Why is road transport in India considered more useful than rail transport? -SST 10th

Last Answer : (i) Road transport is more flexible than rail as buses, trucks and cars may be stopped anywhere and at any time for passengers and goods whereas trains stop at stations only. (ii) Road transports ... all most all areas whereas trains cannot do the same. Roads can be constructed at hilly areas also.

Description : Preliminary project report for a road project must contain (A) The detailed estimated cost based on detailed design (B) The several alternatives of the project that have been considered (C ... , traffic survey, concept design and approximate cost (D) The contract documents for inviting tenders

Last Answer : (C) The soil survey, traffic survey, concept design and approximate cost

Description : When checking for scene safety for the use of an add which of these describe the danger that would stop us from using an aed?

Last Answer : Answer: When checking the scene safety for the use of an AED, the best scenario that describes the dangers and would stop a person from using the AED is; Flammable gases, patient lying in standing water, combustible liquids near the victim.

Description : Describe role of crash bar and saree guard in two wheeler safety.

Last Answer : The role of i) Crash bar: Crash bars aim to protect motorcycle engines and body panels as well as it is used to protect the rider. It is also used as a mount point for accessories like highway ... guards will not only protect the rider, but also the cargo from being pulled into the rear wheel. 

Description : Describe anyone safety mounting used in boilers with sketch.

Last Answer : Boiler Mounting : Fusible Plug Function:  It is very important safety device of a steam boiler, which protects the fire tube boiler against overheating. Location:  It is located just above ... hollow gun became open, the steam rushes into the furnace and puts out the fire (stop). 

Description : Describe the process of safety planning. 

Last Answer : Process of safety planning: The steps of planning are: 1. Identify problems 2. Establish objectives or goals 3. Develop planning premises(eg. Land, labour, capital, market, money, time, production, ... . Select a course of action 7. Formulate derivative (final) plan and sub pland as per need.

Description : Describe in detail safety organization.

Last Answer : Safety Organization: One of the biggest issues facing employers today is the safety of their employees. Workplace accidents are increasingly common. Organizations have a moral responsibility to ensure the safety and well- ... element of safety. ... 3. Safety Equipment. ... 4. Communication.

Description : Describe the main characteristics of road transport in India. -Geography

Last Answer : Main Characteristics of Road transport in India: (i) India has one of the largest road networks in the world with a total length of 42.5 lakh km (2008-09). (ii) About 85% of ... the people as well as states. Roads make the security of nation more strong as they are strategically important.

Description : What is Road Density ? Describe any four major problems faced by road transport in India. -SST 10th

Last Answer : Road density is the length of road per 100 sq. km of area. Problems faced by road transport in India: 1. The road network in India is not enough for the volume of passengers and traffic it ... inadequate. 4. In the cities, the roadways are highly congested. Most of the bridges are old and narrow.

Description : Describe any four major problems faced by the road transportation in India. -SST 10th

Last Answer : Road transport in India faced four major problems. They are as follows : (i) The volume of traffic and passengers, the road network is inadequate. (ii) About half of the roads are unmetalled ... The roadways are highly congested in cities and most of the bridges and culverts are old and narrow.

Description : What is the meaning of road density? Describe any three major problems faced by road transportation in India. -SST 10th

Last Answer : The length of road per sq km of area is known as road density. Road transportation in India faces a number of problems. Three of them are given below: (i) Keeping in view the volume of ... and most of the bridges and culverts are old and narrow. (iv) The National Highways are inadequate too.

Description : Describe any five major problems faced by road transport in India. -SST 10th

Last Answer : Five major problems faced by the road transport in India are (i) Road network is inadequate in India. (ii) About half of the roads are unmetalled and this limits their usage during ... major problem. Citizen have casual attitude towards traffic rules, which leads to accidents causing traffic jams.

Description : Describe three major problems faced by the road transport in India. -SST 10th

Last Answer : Five major problems faced by the road transport in India are: (i) Road network is inadequate in India. (ii) About half of the roads are unmetalled and this limits their usage during the rainy season. (iii) The roadways are highly congested in cities.

Description : Describe any five major problems faced by road transport in India. -SST 10th

Last Answer : Five problems faced by road transport in India are given below: (i) Volume of traffic and passengers is very large. (ii) Road network is inadequate. (iii) Half the roads are unmetalled, ... inadequate. (v) Roadways are highly congested in cities and most bridges and culverts are old and narrow.