250V 100W written on the lamp , what does it mean ?

250V 100W written on the lamp , what does it mean ?
by

1 Answer

Answer :

100W power loss if an electric lamp is supplied within 250V and runs for 1 hour .
by

Related questions

Can I put a 26 Watt energy saver (Equivalent to 100W) in a 60 Watt max lamp?

Description : Can I put a 26 Watt energy saver (Equivalent to 100W) in a 60 Watt max lamp?

Last Answer : yes. It’s equivalent in how much light it gives off compared to a 100W incandescent bulb. Those get much hotter.

A lamp of 100W at 200V is supplied current at 100 volts. It will be equivalent to the lamp of:

Description : A lamp of 100W at 200V is supplied current at 100 volts. It will be equivalent to the lamp of:   a. 50W b. 40W c. 25W d. 10W 

Last Answer : A lamp of 100W at 200V is supplied current at 100 volts. It will be equivalent to the lamp of: 25W

Why ungrounded 250V DC system adopted in our system?

Description : Why ungrounded 250V DC system adopted in our system?

Last Answer : The 250V DC system is feeding to some of the vital loads such as breaker control etc. Even if one ground has occurred then also these controls should be available. Continuous monitoring of ground current is employed to eliminate the by passing of logic due to double ground. 

52 A transformer has 1000 primary turns, connected to 250V ac supply. To get 400V secondary voltage the no of secondary turns should be A. 1600 B. 250 C. 400 D. 1250

Description : 52 A transformer has 1000 primary turns, connected to 250V ac supply. To get 400V secondary voltage the no of secondary turns should be A. 1600 B. 250 C. 400 D. 1250

Last Answer : A. 1600

Cost of using a 100W light bulb for one hour?

Description : Cost of using a 100W light bulb for one hour?

Last Answer : First you have to know the price for 1 kWh. Suppose it was 12 cents. That is usually written .1200 per kWh. Or, 12 cents to use a 100 watt bulb for 10 hours. Because 10 x 100= 1,000 So, it would be ... And also 10% of the cost per kWh which is 12 cents. So, 1 hours use is 1.2 cents in this example.

Two bulbs of 100w and 40w respectively are connected in series across a 230v supply which bulb will glow bright and why?

Description : Two bulbs of 100w and 40w respectively are connected in series across a 230v supply which bulb will glow bright and why?

Last Answer : A:Since two bulbs are in series they will get equal amount of electrical current but as the supply voltage is constant across the bulb(P=V^2/R).So the resistance of 40W bulb is greater and voltage across 40W is more (V=IR) so 40W bulb will glow brighter.

An AM transmitter is rated 100W at 100% modulation. How much power required for the carrier? A. 33.33 W B. 66.66 W C. 83.33 W D. 100 W

Description : An AM transmitter is rated 100W at 100% modulation. How much power required for the carrier? A. 33.33 W B. 66.66 W C. 83.33 W D. 100 W

Last Answer : B. 66.66 W

Two bulbs of 100w and 40w respectively connected in series across a 230v supply which bulb will glow bright and why?

Description : Two bulbs of 100w and 40w respectively connected in series across a 230v supply which bulb will glow bright and why?

Last Answer : Since two bulbs are in series they will get equal amount of electrical current but as the supply voltage is constant across the Bulb (P=V^2/R).So the resistance of 40W bulb is greater and voltage across 40W is more (V=IR) so 40W bulb will glow brighter.

When maximum power transfer to load is a) 20 W b) 50 W c) 100W d) 0W

Description : When maximum power transfer to load is a) 20 W b) 50 W c) 100W d) 0W

Last Answer : Ans: 0W

Three bulbs are rating 40W 60W and 100W designed to work on 220V mains. Which bulb will burn most brightly if they are connected in series across 220 V mains? a. 40 W bulb b. 60 W blub c. 100 W blub d. all will burn equally brightly

Description : Three bulbs are rating 40W 60W and 100W designed to work on 220V mains. Which bulb will burn most brightly if they are connected in series across 220 V mains? a. 40 W bulb b. 60 W blub c. 100 W blub d. all will burn equally brightly

Last Answer : a. 40 W bulb

There are three bulbs of 60W 100W and 200W which bulb has thickest filament. a. 100W b. 200W c. 60W d. All

Description : There are three bulbs of 60W 100W and 200W which bulb has thickest filament. a. 100W b. 200W c. 60W d. All

Last Answer : b. 200W

Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Description : Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Last Answer : b. 90W

Two 100W, 200V lamps are connected in series across a 200V supply. The total power

Description : Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts

Last Answer : 4800

What do you mean by switchgear ?

Description : What do you mean by switchgear ?

Last Answer : Answer : Switch gear does not mean a single corner object. It refers to the position of the electromagnetic system, including the connective , isolating , and maintenance equipment of normal activity .

What does earth continuity mean ?

Description : What does earth continuity mean ?

Last Answer : The conduction wire that connects the earthing lead to the metal cover of electrical furniture, appliances, or wiring is called the earth continuity wire.

What does GMD & GMR mean ?

Description : What does GMD & GMR mean ?

Last Answer : GMD = Geometrical Mean Distance GMR = Geometrical Mean Radiue.

What do you mean by wave wave ?

Description : What do you mean by wave wave ?

Last Answer : A wave wave is a wave wave that is obtained by plotting instantaneous value coordinates of voltage and current.

What do you mean by DC circuit ?

Description : What do you mean by DC circuit ?

Last Answer : DC means direct current. All the circuits that work through the DC source are called DC circuits .

What is frequency ? What does 60c / s bicycle mean ?

Description : What is frequency ? What does 60c / s bicycle mean ?

Last Answer : The number of cycles an AC wave completes in one second is called frequency. Its unit is Hz . It is expressed by f . Frequency 60c / s cycle means complete 60 cycles in 1 second .

D.C. And AC , what do you mean ?

Description : D.C. And AC , what do you mean ?

Last Answer : DC , a short expression of a current flowing in an electric current which is obtained from zero at the moment of onset and flows in the same direction unchanged. A.C. A brief expression of ... in one direction. Again in the opposite direction also from zero to maximum and from maximum to zero.

What does digital signal mean ?

Description : What does digital signal mean ?

Last Answer : A digital signal means that the signal or symbol has two defined levels.

What does digit mean ?

Description : What does digit mean ?

Last Answer : : The origin of digital word from digital word. Digit means number and digital number usually means 0 and 1 .

What does Fan-in mean ?

Description : What does Fan-in mean ?

Last Answer : : The maximum number of input terminals in a gate is called the fan in.

What does backbone mean ?

Description : What does backbone mean ?

Last Answer : The main cable carrying the data of the network is called the backbone , with which the other part of the network keeps the network active from connecting the information segments.

What does relay mean ? What is a relay ?

Description : What does relay mean ? What is a relay ?

Last Answer : A protective device is a relay that detects electrical circuit faults and assists in circuit breaker operation and separates the defective part from the good part.

What does AVO mean ?

Description : What does AVO mean ?

Last Answer : AVO refers to three things. A is the unit of current measurement with amperes. Volt with V is the unit of measurement of voltage. Ohm with O is the unit of measurement of resistance.

What is the conductivity of molar ?

Description : What is the conductivity of molar ?

Last Answer : The density of a solution as cm. When one mole of electrolytic substance is dissolved in it, the conductivity obtained by multiplying it by the relative conductivity of the solution is called molecular conductivity of the solution .

How do I purchase a product ?

Description : How do I purchase a product ?

Last Answer : From Alibaba you can purchase products by paying MASTER CARD or through bank.

What is an analog signal ?

Description : What is an analog signal ?

Last Answer : Signals whose values ​​change continuously are called analog signals. For example- voltage of electricity supplied to the house.

What is Zener Diod ?

Description : What is Zener Diod ?

Last Answer : Zener diode is a special type of diode which, like ordinary diode, not only conducts current in the forward direction , but also in the opposite direction if the voltage exceeds the level of breakdown ... diode is to use the shunt regulator and the voltage reference as the voltage of the circuit.

What is the multiplying factor of shunt ?

Description : What is the multiplying factor of shunt ?

Last Answer : Answer : The ratio of load or matte current to ammeter current is called shunt multiplying power.

What is ammeter shunt ?

Description : What is ammeter shunt ?

Last Answer : A small amount of radial coupling in parallel with the coil to increase the range of ammeter is called ammeter shunt.

What is short circuit current ?

Description : What is short circuit current ?

Last Answer : Answer : A fault in an electrical system whose current, before or after the current flows through the load, is combined with one or more phases of neutral current which causes more current to flow than normal. The current is called short circuit current.

What is a current limiting reactor ? How many types and what are they ?

Description : What is a current limiting reactor ? How many types and what are they ?

Last Answer : Answer : A current limiting reactor is basically an inductive coil which limits the short circuit current by providing inductive reactance when required. Types: 1. Based on the structure- a) Dry type ... reactor. Basbar reactors are again of 2 types- a) Ring system reactor b) Tiber system reactor

What is the method of diagnosing short circuit current ?

Description : What is the method of diagnosing short circuit current ?

Last Answer : There are three methods for determining short circuit current , namely- 1) Ohmic method 2) Per unit method 3.) Percentage reactance method.

What are symmetrical and asymmetrical faults ?

Description : What are symmetrical and asymmetrical faults ?

Last Answer : Symmetrical Fault: The same amount in each phase due to the float in the electrical system. The fault that causes hot current to flow is called semantic fault. Circuit breaker ratings are determined by ... through each fan is called an asymmetrical fault. The relay is set via asymmetrical font.

What is Basbar and Bas Kaplar ?

Description : What is Basbar and Bas Kaplar ?

Last Answer : Basbar : Basbar is basically a sheet or color of copper or aluminum. It is the job of the bus driver to deliver power to one or more lads with power from one or more cables. Bus ... is basically a combination of circuit breaker and isolator. There are fire proof walls around the bus coupler.

Why is the busbar sectionalized ?

Description : Why is the busbar sectionalized ?

Last Answer : Answer : If an error occurs in any part of the busbar, the operation of the entire busbar system will not stop. The maximum success of this system is due to the interconnection of different sections of the circuit and the smooth distribution in the outgoing circuit.

title : _

Description : title : _

Last Answer : Basbar is a type of copper and aluminum conductive sheet or mata rod , which collects electrical energy from one or more circuits and distributes that energy through one or more circuits.

Write different font names or different short circuit font names ?

Description : Write different font names or different short circuit font names ?

Last Answer : There are two main types of short circuit faults. Namely- 1. Semantic faults and 2. Asymmetrical font Symmetrical fault - a) Short circuit three phases together b) Short circuit asymmetrical fault with three ... result c) Double line to ground font d) Two phase one Circuit and third phase earth.

What is Electrical Fault ? What is the cause of the fault ?

Description : What is Electrical Fault ? What is the cause of the fault ?

Last Answer : Answer : Fault: When two or more conductors come in contact with each other while operating at normal voltage difference, the result is said to be organized. Causes of Fault: Faults are organized due to ... loss of line c) Lightning charge d) Voltage drop e) Loss of unbalance and stability etc.

What features should a switchgear have ?

Description : What features should a switchgear have ?

Last Answer : Switchgear should have the following characteristics- a) Sensitivity b) Detection ability c) Reliability d) High speed e) Durability. F) Expansion advantage g) Simplicity.

What are the components of switch gear ?

Description : What are the components of switch gear ?

Last Answer : The components of switch gear are: circuit breaker , relay , instrument transformer , housing , conductor etc.

What is an Earth Electrode ?

Description : What is an Earth Electrode ?

Last Answer : Puta metal part in the soil which connects to the soil is called earth electrode. Thank you all for today's electrical questions and answers.

What is Earthing Lead ?

Description : What is Earthing Lead ?

Last Answer : The wire that connects the earth continuity wire and the earth electrode is called the earthing lead.

What earthing is done in hilly areas ?

Description : What earthing is done in hilly areas ?

Last Answer : Sheet earthing is done in hilly areas. Shit electrodes are placed by digging trenches on the slopes of the hill.

What should be the size of rod earthing ?

Description : What should be the size of rod earthing ?

Last Answer : In case of iron or steel rod the diameter is 16 mm but in case of copper rod it is 12.5 mm. In both cases the length is at least 2.5 m. Is to be.

Which earthing is less expensive ?

Description : Which earthing is less expensive ?

Last Answer : Rod earthing is the least expensive. Because the soil does not have to be eroded, the cost is less than other earthing.

What should be the size of the pipe electrode ?

Description : What should be the size of the pipe electrode ?

Last Answer : The size of the pipe electrode should be 36 mm diameter 2 to 2.75 m long galvanized iron or steel pipe.

How many types of earthing and what are they ?

Description : How many types of earthing and what are they ?

Last Answer : There are two types of earthing , namely _ a) system earthing b) equipment earthing.