When maximum power transfer to load is a) 20 W b) 50 W c) 100W d) 0W

When maximum power transfer to load is
a) 20 W
b) 50 W
c) 100W
d) 0W
by

1 Answer

Answer :

Ans: 0W
by

Related questions

For a temperature difference `DeltaT=20.0^(@)C`, one slab of material conducts `10.0W//m^(2)` , another of the same shape conduct `20.0W//m^(2)`. What

Description : For a temperature difference `DeltaT=20.0^(@)C`, one slab of material conducts `10.0W//m^(2)` , another of the same shape conduct `20.0W//m^(2)`. What

Last Answer : For a temperature difference `DeltaT=20.0^(@)C`, one slab of material conducts `10.0W//m^(2)` , another of the ... C. `20/3 W//m^(2)` D. none of these

What is SAE 0W-20 and what does 0W-20 mean?

Description : What is SAE 0W-20 and what does 0W-20 mean?

Last Answer : What is the answer ?

An AM transmitter is rated 100W at 100% modulation. How much power required for the carrier? A. 33.33 W B. 66.66 W C. 83.33 W D. 100 W

Description : An AM transmitter is rated 100W at 100% modulation. How much power required for the carrier? A. 33.33 W B. 66.66 W C. 83.33 W D. 100 W

Last Answer : B. 66.66 W

Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Description : Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Last Answer : b. 90W

Two bulbs of 100w and 40w respectively are connected in series across a 230v supply which bulb will glow bright and why?

Description : Two bulbs of 100w and 40w respectively are connected in series across a 230v supply which bulb will glow bright and why?

Last Answer : A:Since two bulbs are in series they will get equal amount of electrical current but as the supply voltage is constant across the bulb(P=V^2/R).So the resistance of 40W bulb is greater and voltage across 40W is more (V=IR) so 40W bulb will glow brighter.

Two bulbs of 100w and 40w respectively connected in series across a 230v supply which bulb will glow bright and why?

Description : Two bulbs of 100w and 40w respectively connected in series across a 230v supply which bulb will glow bright and why?

Last Answer : Since two bulbs are in series they will get equal amount of electrical current but as the supply voltage is constant across the Bulb (P=V^2/R).So the resistance of 40W bulb is greater and voltage across 40W is more (V=IR) so 40W bulb will glow brighter.

Three bulbs are rating 40W 60W and 100W designed to work on 220V mains. Which bulb will burn most brightly if they are connected in series across 220 V mains? a. 40 W bulb b. 60 W blub c. 100 W blub d. all will burn equally brightly

Description : Three bulbs are rating 40W 60W and 100W designed to work on 220V mains. Which bulb will burn most brightly if they are connected in series across 220 V mains? a. 40 W bulb b. 60 W blub c. 100 W blub d. all will burn equally brightly

Last Answer : a. 40 W bulb

Two 100W, 200V lamps are connected in series across a 200V supply. The total power

Description : Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts

Last Answer : 4800

Can I put a 26 Watt energy saver (Equivalent to 100W) in a 60 Watt max lamp?

Description : Can I put a 26 Watt energy saver (Equivalent to 100W) in a 60 Watt max lamp?

Last Answer : yes. It’s equivalent in how much light it gives off compared to a 100W incandescent bulb. Those get much hotter.

250V 100W written on the lamp , what does it mean ?

Description : 250V 100W written on the lamp , what does it mean ?

Last Answer : 100W power loss if an electric lamp is supplied within 250V and runs for 1 hour .

Cost of using a 100W light bulb for one hour?

Description : Cost of using a 100W light bulb for one hour?

Last Answer : First you have to know the price for 1 kWh. Suppose it was 12 cents. That is usually written .1200 per kWh. Or, 12 cents to use a 100 watt bulb for 10 hours. Because 10 x 100= 1,000 So, it would be ... And also 10% of the cost per kWh which is 12 cents. So, 1 hours use is 1.2 cents in this example.

There are three bulbs of 60W 100W and 200W which bulb has thickest filament. a. 100W b. 200W c. 60W d. All

Description : There are three bulbs of 60W 100W and 200W which bulb has thickest filament. a. 100W b. 200W c. 60W d. All

Last Answer : b. 200W

A lamp of 100W at 200V is supplied current at 100 volts. It will be equivalent to the lamp of:

Description : A lamp of 100W at 200V is supplied current at 100 volts. It will be equivalent to the lamp of:   a. 50W b. 40W c. 25W d. 10W 

Last Answer : A lamp of 100W at 200V is supplied current at 100 volts. It will be equivalent to the lamp of: 25W

A generating station has a maximum demand of 50 Mw, a load factor of 60%, a plant capacity factor...

Description : A generating station has a maximum demand of 50 Mw, a load factor of 60%, a plant capacity factor of 45% and if the plant while running as per schedule, were fully loaded. The daily energy produced will be

Last Answer : A generating station has a maximum demand of 50 Mw, a load factor of 60%, a plant capacity factor of 45% and if the plant while running as per schedule, were fully loaded. The daily energy produced will be 720 MW.

The frequency of the rotor current in a 3 phase 50 Hz, 4 pole induction motor at full load speed is about (A) 50 Hz. (B) 20 Hz. (C) 2 Hz. (D) Zero.

Description : The frequency of the rotor current in a 3 phase 50 Hz, 4 pole induction motor at full load speed is about (A) 50 Hz. (B) 20 Hz. (C) 2 Hz. (D) Zero.

Last Answer : (C) 2 Hz.

What is the maximum power that can be obtained from a microwave tube at 10 GHz? A. 500 W B. 10 W C. 50 W D. 20 W

Description : What is the maximum power that can be obtained from a microwave tube at 10 GHz? A. 500 W B. 10 W C. 50 W D. 20 W

Last Answer : B. 10 W

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Last Answer : Answer: C

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Last Answer : Answer: C

A matched termination in which the electromagnetic energy is absorbed by water. A. Maximum power transfer B. Load C. Load water D. Basin

Description : A matched termination in which the electromagnetic energy is absorbed by water. A. Maximum power transfer B. Load C. Load water D. Basin

Last Answer : C. Load water

Transmission line must be matched to the load to A. transfer maximum voltage to the load B. transfer maximum current to the load C. reduce the load current D. transfer maximum power to the load

Description : Transmission line must be matched to the load to A. transfer maximum voltage to the load B. transfer maximum current to the load C. reduce the load current D. transfer maximum power to the load

Last Answer : D. transfer maximum power to the load

What condition gives maximum power transfer from the source to the load?

Description : What condition gives maximum power transfer from the source to the load?

Last Answer : When the load resistance equals the source resistance.

In order to get maximum power transfer from a capacitive source, the load must?

Description : In order to get maximum power transfer from a capacitive source, the load must? A.have a capacitive reactance equal to circuit resistance B.have an impedance that is the complex conjugate of the source impedance C.be as capacitive as it is inductive D.none of the above

Last Answer : In order to get maximum power transfer from a capacitive source, the load must? A.have a capacitive reactance equal to circuit resistance B.have an impedance that is the complex conjugate of the source impedance C.be as capacitive as it is inductive D.none of the above

When replacing a power transistor fitted with a heat sink in a circuit, a coating of silicone grease is applied between the transistor case and the heat sink. This is done to ____________. A. lubricate the transistor B. lubricate the heat sink C. aid in the removal of the heat sink D. provide maximum heat transfer

Description : When replacing a power transistor fitted with a heat sink in a circuit, a coating of silicone grease is applied between the transistor case and the heat sink. This is done to ____________. A. lubricate ... the heat sink C. aid in the removal of the heat sink D. provide maximum heat transfer

Last Answer : Answer: D

State Maximum power transfer theorem

Description : State Maximum power transfer theorem

Last Answer : The Maximum power transfer theorem explains about the load that a resistance will extract from the network. This includes the maximum power from the network and in this case the load resistance ... the output terminals and the energy sources can be removed by leaving the internal resistance behind.

A 3-phase 50HZ SCIM takes a power input of 30 KW at its full load speed of 1440 rpm. Total stator losses are 1 KW. The slip and rotor ohmic losses at full load are a) 0.02, 600 W b) 0.04, 580 W c) 0.04, 1160 W d) 0.04, 1200 W

Description : A 3-phase 50HZ SCIM takes a power input of 30 KW at its full load speed of 1440 rpm. Total stator losses are 1 KW. The slip and rotor ohmic losses at full load are a) 0.02, 600 W b) 0.04, 580 W c) 0.04, 1160 W d) 0.04, 1200 W

Last Answer : Ans: 0.04, 1160 W

Two paralleled alternators are operating near rated load. If one trips out mechanically, which of the listed actions should be taken FIRST? A. Restart the tripped machine immediately. B. Strip the board of all non-vital circuits. C. Start the emergency generator. D. Transfer all vital loads to the emergency bus.

Description : Two paralleled alternators are operating near rated load. If one trips out mechanically, which of the listed actions should be taken FIRST? A. Restart the tripped machine immediately. B. Strip the board ... circuits. C. Start the emergency generator. D. Transfer all vital loads to the emergency bus.

Last Answer : Answer: B

A 3 phase 50 Hz induction motor has full load speed of 970 rpm. Calculate no of poles and slip frequency.

Description : A 3 phase 50 Hz induction motor has full load speed of 970 rpm. Calculate no of poles and slip frequency.

Last Answer : The number of poles in an induction motor can be calculated using the following formula: No. of poles = (120 * frequency) / speed In this case, the number of poles would be calculated as follows: No. of poles = ( ... ) - 50 Hz = 8.08 Hz So the motor has 6 poles and a slip frequency of 8.08 Hz.

If the illustrated lighting branch distribution box is not for cargo or deck lighting, the Coast Guard Regulations (46 CFR) requires the designed load attached to Branch NO.2 to be no more than _________. EL-0013 A. 5 amps B. 16 amps C. 30 amps D. 50 amps

Description : If the illustrated lighting branch distribution box is not for cargo or deck lighting, the Coast Guard Regulations (46 CFR) requires the designed load attached to Branch NO.2 to be no more than _________. EL-0013 A. 5 amps B. 16 amps C. 30 amps D. 50 amps

Last Answer : Answer: B

Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Description : Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Last Answer : (C) 50 -100 BTU/hr. ft. 2°F

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

What is the direction of current through the load resistor in the circuit shown in the illustration? EL-0085 A. Always from point 'Z' to the grounded end. B. Always from the grounded end to point 'Z'. C. It depends on the instantaneous polarity at point 'W'. D. It cannot be determined without a directional ammeter.

Description : What is the direction of current through the load resistor in the circuit shown in the illustration? EL-0085 A. Always from point 'Z' to the grounded end. B. Always from the grounded end to ... on the instantaneous polarity at point 'W'. D. It cannot be determined without a directional ammeter.

Last Answer : Answer: B

Maximum data transfer rate of the optical fiber is……….? a. 50 kbps b. 1000 kbps c. 1000 Mbps d. None of the these

Description : Maximum data transfer rate of the optical fiber is……….? a. 50 kbps b. 1000 kbps c. 1000 Mbps d. None of the these

Last Answer : c. 1000 Mbps

An autotransformer is equipped with a 50% tap, a 65% tap, and an 80% tap. Which of the following statements is true concerning a load connected to the 50% tap? A. The load is receiving minimum voltage and minimum current. B. The load is receiving minimum voltage and maximum current. C. The load is receiving maximum voltage and minimum current. D. The load is receiving maximum voltage and maximum current.

Description : An autotransformer is equipped with a 50% tap, a 65% tap, and an 80% tap. Which of the following statements is true concerning a load connected to the 50% tap? A. The load is ... is receiving maximum voltage and minimum current. D. The load is receiving maximum voltage and maximum current.

Last Answer : Answer: B

One item listed on the name plate of a cargo pump motor is 'degrees centigrade rise.' This number is based on _____________. A. normal temperature change from cold to hot B. an ambient temperature of 40°C C. minimum heat rise from no load to full load D. maximum degrees centigrade rise from absolute zero

Description : One item listed on the name plate of a cargo pump motor is 'degrees centigrade rise.' This number is based on _____________. A. normal temperature change from cold to hot B. an ambient temperature ... . minimum heat rise from no load to full load D. maximum degrees centigrade rise from absolute zero

Last Answer : Answer: B

Motor name plate data includes '°°C rise'. This indicates the _____________. A. actual running temperature of the winding from no load to full load B. permissible temperature rise of the windings above the designed ambient temperature C. maximum allowable temperature rise above normal full load operating temperature D. maximum allowable temperature rise for continuous no load service

Description : Motor name plate data includes '°°C rise'. This indicates the _____________. A. actual running temperature of the winding from no load to full load B. permissible temperature rise ... above normal full load operating temperature D. maximum allowable temperature rise for continuous no load service

Last Answer : Answer: B

The full load torque of an electric motor is the __________. A. minimum torque developed by the motor accelerating from stop to full speed B. turning moment exerted by the motor at rated load and speed C. maximum torque developed by the motor with rated voltage and frequency D. turning moment exerted by the motor from any rotor angular position at any load

Description : The full load torque of an electric motor is the __________. A. minimum torque developed by the motor accelerating from stop to full speed B. turning moment exerted by the motor at rated load ... and frequency D. turning moment exerted by the motor from any rotor angular position at any load

Last Answer : Answer: B

There Are A transformer And An Induction Machine. Those Two Have The Same Supply. For Which Device The Load Current Will Be Maximum? And Why?

Description : There Are A transformer And An Induction Machine. Those Two Have The Same Supply. For Which Device The Load Current Will Be Maximum? And Why?

Last Answer : The motor has max load current compare to that of trformer because the motor consumes real power.. and the trformer is only producing the working flux and its not consuming.. hence the load current in the trformer is because of core loss so it is minimum.

What is the maximum load on MCC?

Description : What is the maximum load on MCC?

Last Answer : 3 Phase load upto 90 kW are fed by MCC. 

Define the following: Average demand, Maximum demand, Demand factor, Load factor.

Description : Define the following: Average demand, Maximum demand, Demand factor, Load factor.

Last Answer : Average Demand: the average power requirement during some specified period of time of considerable duration is called the average demand of installation. Maximum Demand: The maximum demand of an installation ... Load Factor: It is defined as the ratio of the average power to the maximum demand.

A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the terminal voltage of 220V. If the same machine is run as a motor it takes a line current of 20A from 220V supply. The speed of the machine as a motor will be (A) 800 rpm. (B) more than 800 rpm. (C) less than 800 rpm. (D) both higher or lower than 800 rpm.

Description : A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the terminal voltage of 220V. If the same machine is run as a motor it takes a line current of 20A from 220V supply. The speed of ... . (B) more than 800 rpm. (C) less than 800 rpm. (D) both higher or lower than 800 rpm.

Last Answer : (C) less than 800 rpm.

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

A rectangular log of wood is floating in water with a load of 100 N at its centre. The maximum shear force in the wooden log is (A) 50 N at each end (B) 50 N at the centre (C) 100 N at the centre (D) None of these

Description : A rectangular log of wood is floating in water with a load of 100 N at its centre. The maximum shear force in the wooden log is (A) 50 N at each end (B) 50 N at the centre (C) 100 N at the centre (D) None of these

Last Answer : (C) 100 N at the centre

A generating station has a maximum demand of 500 MW. The annual load factor is 50 percent. The energy

Description : A generating station has a maximum demand of 500 MW. The annual load factor is 50 percent. The energy generated per annum will be: A) 2.19 x 106 MWhr B) 600 MWhr C) 250 MWhr D) 7.50 x 106 MWhr

Last Answer : A generating station has a maximum demand of 500 MW. The annual load factor is 50 percent. The energy generated per annum will be: 2.19 x 106 MWhr 

A pile is being driven with a drop hammer weighing 1800 kg and having a free fall of 1.00 m. If the penetration with last blow is 5 mm, the load carrying capacity of the pile, -according to the Engineering News formula, is (A) 100 tonnes (B) 50 tonnes (C) 20 tonnes (D) 10 tonnes

Description : A pile is being driven with a drop hammer weighing 1800 kg and having a free fall of 1.00 m. If the penetration with last blow is 5 mm, the load carrying capacity of the pile, -according to the Engineering News formula, is (A) 100 tonnes (B) 50 tonnes (C) 20 tonnes (D) 10 tonnes

Last Answer : (D) 10 tonnes

The dielectric strength of a vacuum or dry air is approximately ________________. A. 450 volts/inch B. 1000 volts/inch C. 20-kv/inch D. 50-kv/inch

Description : The dielectric strength of a vacuum or dry air is approximately ________________. A. 450 volts/inch B. 1000 volts/inch C. 20-kv/inch D. 50-kv/inch

Last Answer : Answer: C

What is the approximate voltage produced by a nickel-cadmium battery cell? A. 1.25 volts B. 1.50 volts C. 2.20 volts D. 6.05 volts

Description : What is the approximate voltage produced by a nickel-cadmium battery cell? A. 1.25 volts B. 1.50 volts C. 2.20 volts D. 6.05 volts

Last Answer : Answer: A

The ratio of the maximum deflections of a simply supported beam with a central load W and of a cantilever of same length and with a load W at its free end, is (A) 1/8 (B) 1/10 (C) 1/12 (D) 1/16

Description : The ratio of the maximum deflections of a simply supported beam with a central load W and of a  cantilever of same length and with a load W at its free end, is  (A) 1/8  (B) 1/10  (C) 1/12  (D) 1/16 

Last Answer : (D) 1/16 

The maximum deflection due to a load W at the free end of a cantilever of length L and having flexural rigidity EI, is (A) WL²/2EI (B) WL²/3EI (C) WL3 /2EI (D) WL3 /3EI

Description : The maximum deflection due to a load W at the free end of a cantilever of length L and having  flexural rigidity EI, is  (A) WL²/2EI (B) WL²/3EI (C) WL3 /2EI (D) WL3 /3EI

Last Answer : (D) WL3 /3EI

The maximum bending moment for a simply supported beam with a uniformly distributed load w/unit length, is (A) WI/2 (B) WI²/4 (C) WI²/8 (D) WI²/12

Description : The maximum bending moment for a simply supported beam with a uniformly distributed  load w/unit length, is  (A) WI/2  (B) WI²/4  (C) WI²/8  (D) WI²/12

Last Answer : (C) WI²/8 

A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated  load W at its mid-span. The same bar experiences an extension e under same tensile load. The  ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Last Answer : (C) (L/2d)