If the bit rate for an FSK signal is1200 bps, thebaud rate is ________. A) 300 B) 400 C) 600 D) 1200

If the bit rate for an FSK signal is1200 bps, thebaud rate is ________.
A)
300
B)
400
C)
600
D)
1200
by

1 Answer

Answer :

1200
by

Related questions

f the bit rate for an ASK signal is1200 bps, thebaud rate is ________. A) 300 B) 400 C) 600 D) 1200

Description : f the bit rate for an ASK signal is1200 bps, thebaud rate is ________. A) 300 B) 400 C) 600 D) 1200

Last Answer : 1200

If the bit rate for a16-QAM signal is 4000 bps, what is the baudrate? A) 300 B) 400 C) 1000 D) 1200

Description : If the bit rate for a16-QAM signal is 4000 bps, what is the baudrate? A) 300 B) 400 C) 1000 D) 1200

Last Answer : 1000

If the baudrate is400 for a QPSK signal, thebit rate is ________ bps. A) 100 B) 400 C) 800 D) 1600

Description : If the baudrate is400 for a QPSK signal, thebit rate is ________ bps. A) 100 B) 400 C) 800 D) 1600

Last Answer : 800

What arethe most commonly used transmission speeds in BPS usedin datacommunication? A. 300 B. 1200 C. 2400 D. 9600 E. None of the above

Description : What arethe most commonly used transmission speeds in BPS usedin datacommunication? A. 300 B. 1200 C. 2400 D. 9600 E. None of the above

Last Answer : 9600

Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is __________. a. 400 bps b. 800 bps c. 1600 bps d. 3200 bps

Description : Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is __________. a. 400 bps b. 800 bps c. 1600 bps d. 3200 bps

Last Answer : d. 3200 bps

If the baudrate fora 64-QAM signal is 2000, what is the bit rate? A) 300 B) 400 C) 1000 D) 12000

Description : If the baudrate fora 64-QAM signal is 2000, what is the bit rate? A) 300 B) 400 C) 1000 D) 12000

Last Answer : 12000

If digitaldata rateof 9600 bps is encoded using 8-level phaseshift keying (PSK) method, the modulation rate is A. 1200 bands B. 3200 bands C. 4800 bands D. 9600 bands E. None of the above

Description : If digitaldata rateof 9600 bps is encoded using 8-level phaseshift keying (PSK) method, the modulation rate is A. 1200 bands B. 3200 bands C. 4800 bands D. 9600 bands E. None of the above

Last Answer : 3200 bands

How many 8-bit characters can be transmitted per second over a 9600 baud serial communication link using asynchronous mode of transmission with one start bit, eight data bits, two stop bits, and one parity bit ? a. 600 b. 800 c. 876 d. 1200

Description : How many 8-bit characters can be transmitted per second over a 9600 baud serial communication link using asynchronous mode of transmission with one start bit, eight data bits, two stop bits, and one parity bit ? a. 600 b. 800 c. 876 d. 1200

Last Answer : b. 800

If the frequency spectrum of a signal has a bandwidth of500 Hz with thehighest frequency at 600 Hz, what shouldbe the samplingrate, according to the Nyquist theorem? A) 200 samples/s B) 500 samples/s C) 1000 samples/s D) 1200 samples/s

Description : If the frequency spectrum of a signal has a bandwidth of500 Hz with thehighest frequency at 600 Hz, what shouldbe the samplingrate, according to the Nyquist theorem? A) 200 samples/s B) 500 samples/s C) 1000 samples/s D) 1200 samples/s

Last Answer : 1200 samples/s

Usually, it takes10-bits to represent one character. How many characters can betransmittedat a speed of 1200 BPS? A. 10 B. 12 C. 120 D. 1200 E. None of the above

Description : Usually, it takes10-bits to represent one character. How many characters can betransmittedat a speed of 1200 BPS? A. 10 B. 12 C. 120 D. 1200 E. None of the above

Last Answer : 120

A device is sending out data at the rate of 2000 bps. How long does it take to send a file of 1,00,000 characters ? a. 50 b. 200 c. 400 d. 800

Description : A device is sending out data at the rate of 2000 bps. How long does it take to send a file of 1,00,000 characters ? a. 50 b. 200 c. 400 d. 800

Last Answer : c. 400

A terminal multiplexer has six 1200 bps terminals and ‘n’ 300 bps terminals connected to it. If the outgoing line is 9600 bps, what is the value of n ? (A) 4 (B) 8 (C) 16 (D) 28

Description : A terminal multiplexer has six 1200 bps terminals and ‘n’ 300 bps terminals connected to it. If the outgoing line is 9600 bps, what is the value of n ? (A) 4 (B) 8 (C) 16 (D) 28

Last Answer : (B) 8

Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is ............... (A) 400 bps (B) 800 bps (C) 1600 bps (D) 3200 bps

Description : Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is ............... (A) 400 bps (B) 800 bps (C) 1600 bps (D) 3200 bps

Last Answer : (D) 3200 bps Answer: D Explanation: The multiplexer is shown in the Figure. Each frame carries 1 byte from each channel; the size of each frame, therefore, is 4 bytes, or 32 bits. Because each ... channel, the frame rate must be 100 frames per second. The bit rate is 100 32 = 3200 bps. 

In_______, the peakamplitude of one signal level is 0; the other is thesame as the amplitude of the carrier frequency. A) PSK B) OOK C) FSK D) none of the above

Description : In_______, the peakamplitude of one signal level is 0; the other is thesame as the amplitude of the carrier frequency. A) PSK B) OOK C) FSK D) none of the above

Last Answer : OOK

In_________, the frequencyof the carrier signal is varied to representdata. Both peak amplitudeand phase remain constant. A) ASK B) PSK C) FSK D) QAM

Description : In_________, the frequencyof the carrier signal is varied to representdata. Both peak amplitudeand phase remain constant. A) ASK B) PSK C) FSK D) QAM

Last Answer : FSK

In________, the amplitude of the carrier signal is varied to create signal elements. Both frequency and phase remainconstant. A) ASK B) PSK C) FSK D) QAM

Description : In________, the amplitude of the carrier signal is varied to create signal elements. Both frequency and phase remainconstant. A) ASK B) PSK C) FSK D) QAM

Last Answer : ASK

An analog signal carries 4 bits in each signal unit. If 1000 signal units are sent per second, then baud rate and bit rate of the signal are ............... and .............. (A) 4000 bauds \ sec & 1000 bps (B) 2000 bauds \ sec & 1000 bps (C) 1000 bauds \ sec & 500 bps (D) 1000 bauds \ sec & 4000 bps

Description : An analog signal carries 4 bits in each signal unit. If 1000 signal units are sent per second, then baud rate and bit rate of the signal are ............... and .............. (A) 4000 bauds \ sec & ... (B) 2000 bauds \ sec & 1000 bps (C) 1000 bauds \ sec & 500 bps (D) 1000 bauds \ sec & 4000 bps

Last Answer : (D) 1000 bauds \ sec & 4000 bps Explanation: Bit rate is the number of bits per second. Baud rate is the number of signal units per second. Baud rate is less than or equal to the bit rate. Baud rate = 1000 bauds per second (baud/s) Bit rate = 1000 x 4 = 4000 bps

An analog signal has a bit rate of 6000 bps and a baud rate of 2000 baud. How many data elements are carried by each signal element ? (A) 0.336 bits/baud (B) 3 bits/baud (C) 120,00,000 bits/baud (D) None of the above

Description : An analog signal has a bit rate of 6000 bps and a baud rate of 2000 baud. How many data elements are carried by each signal element ? (A) 0.336 bits/baud (B) 3 bits/baud (C) 120,00,000 bits/baud (D) None of the above

Last Answer : (B) 3 bits/baud

The ________ rate defines thenumber of dataelements sent in1s; the______ rate is the numberof signalelements sent in 1s. A) data; signal B) signal; data C) baud; bit D) none of the above

Description : The ________ rate defines thenumber of dataelements sent in1s; the______ rate is the numberof signalelements sent in 1s. A) data; signal B) signal; data C) baud; bit D) none of the above

Last Answer : data; signal

In an IPv4 datagram, the M bit is 0, the value of HLEN is 10, the value of total length is 400 and the fragment offset value is 300. The position of the datagram, the sequence numbers of the first and the last bytes of the payload, respectively are a. Last fragment, 2400 and 2789 b. First fragment, 2400 and 2759 c. Last fragment, 2400 and 2759 d. Middle fragment, 300 and 689

Description : In an IPv4 datagram, the M bit is 0, the value of HLEN is 10, the value of total length is 400 and the fragment offset value is 300. The position of the datagram, the sequence numbers of the ... 2789 b. First fragment, 2400 and 2759 c. Last fragment, 2400 and 2759 d. Middle fragment, 300 and 689

Last Answer : c. Last fragment, 2400 and 2759

In an IPv4 datagram, the M bit is 0, the value of HLEN is 10, the value of total length is 400 and the fragment offset value is 300. The position of the datagram, the sequence numbers of the first and the last bytes of the payload, respectively are a. Last fragment, 2400 and 2789 b. First fragment, 2400 and 2759 c. Last fragment, 2400 and 2759 d. Middle fragment, 300 and 689

Description : In an IPv4 datagram, the M bit is 0, the value of HLEN is 10, the value of total length is 400 and the fragment offset value is 300. The position of the datagram, the sequence numbers of the ... 2789 b. First fragment, 2400 and 2759 c. Last fragment, 2400 and 2759 d. Middle fragment, 300 and 689

Last Answer : c. Last fragment, 2400 and 2759

If delaysare recorded as 10 bit numbers in a 50 router network, and delay vectorsare exchanged twicea second,how muchbandwidth per fill duplex line is occupied by the distributedrouting algorithm? A. 500 bps B. 1500 bps C. 5 bps D. 1000 bps

Description : If delaysare recorded as 10 bit numbers in a 50 router network, and delay vectorsare exchanged twicea second,how muchbandwidth per fill duplex line is occupied by the distributedrouting algorithm? A. 500 bps B. 1500 bps C. 5 bps D. 1000 bps

Last Answer : 1000 bps

The probability thata singlebit will be inerror on a typical public telephone lineusing 4800 bps modem is 10 to the power -3. If no error detection mechanism is used, the residual error ratefor a communicationline using 9-bit frames is approximately equal to A. 0.003 B. 0.009 C. 0.991 D. 0.999 E. None of the above

Description : The probability thata singlebit will be inerror on a typical public telephone lineusing 4800 bps modem is 10 to the power -3. If no error detection mechanism is used, the residual error ratefor a communicationline using 9-bit frames is ... to A. 0.003 B. 0.009 C. 0.991 D. 0.999 E. None of the above

Last Answer : 0.009

In a token ring network the transmission speed is 10^7 bps and the propagation speed is 200 metres/micro second. The 1- bit delay in this network is equivalent to: a. 500 metres of cable. b. 200 metres of cable. c. 20 metres of cable. d. 50 metres of cable

Description : In a token ring network the transmission speed is 10^7 bps and the propagation speed is 200 metres/micro second. The 1- bit delay in this network is equivalent to: a. 500 metres of cable. b. 200 metres of cable. c. 20 metres of cable. d. 50 metres of cable

Last Answer : c. 20 metres of cable.

Saturated steam at 1 atm is discharged from a turbine at 1200 kg/h. Superheated steam at 300 0C and 1 atm is needed as a feed to a heat exchanger. To produce it, the turbine discharge stream is mixed with superheated steam at 400 0C, 1 atm and specific volume of 3.11 m 3 /kg. Calculate the amount of superheated steam at 300 0C produced and the volumetric flow rate of the 400 0C steam.

Description : Saturated steam at 1 atm is discharged from a turbine at 1200 kg/h. Superheated steam at 300 0C  and 1 atm is needed as a feed to a heat exchanger. To produce it, the turbine discharge ... amount of superheated steam at 300 0C produced and the volumetric flow rate of the  400 0C steam.

Last Answer : Solution 1. Mass balance of water 1200 + m1 = m2 ………………………………………… (1) …………………….1 mark 2. Energy balance (1200 kg/h)(2676 kJ/kg) + m1(3278 kJ/kg)

Iridium satellites can provide data communications of up ____ bps data rate. A. 1200 B. 4800 C. 2400 D. 3840

Description : Iridium satellites can provide data communications of up ____ bps data rate. A. 1200 B. 4800 C. 2400 D. 3840

Last Answer : C. 2400

For protection of level crossing gate in an emergency on BG double line the Gateman should place one detonator at one place and 3 detonators at a subsequent place at a distance of ------- a) and------- meters respectively b) 400 meters in 800 meters c) 500 meters and 1000 meters d) 600 meters and 1200 meters* e) 800 meters in 1500 meters

Description : For protection of level crossing gate in an emergency on BG double line the Gateman should place one detonator at one place and 3 detonators at a subsequent place at a distance of ------- a) and------ ... c) 500 meters and 1000 meters d) 600 meters and 1200 meters* e) 800 meters in 1500 meters

Last Answer : d) 600 meters and 1200 meters*

Indication post for detonator should be provided at a distance of ---------meter and --------- meter for BG level crossing a) 400 meters in 800 meters b) 500 meters and 1200 meters c) 600 meters and 1200 meter * d)600 meters and 1000 meters

Description : Indication post for detonator should be provided at a distance of ---------meter and --------- meter for BG level crossing a) 400 meters in 800 meters b) 500 meters and 1200 meters c) 600 meters and 1200 meter * d)600 meters and 1000 meters

Last Answer : c) 600 meters and 1200 meter *

P and Q undertake to do a piece of job for Rs.1200. P alone can do it in 12 days while Q alone can do it in 16 days. With the help of R , they finish it in 6 days. Find the share of P,Q & R. a) 400,600,200 b) 200,400,600 c) 450,400,250 d) 600,450,150

Description :  P and Q undertake to do a piece of job for Rs.1200. P alone can do it in 12 days while Q alone can do it in 16 days. With the help of R , they finish it in 6 days. Find the share of P,Q & R. a) 400,600,200 b) 200,400,600 c) 450,400,250 d) 600,450,150

Last Answer : D R;s 1 day work = 1/6 – (1/12 + 1/16) =1/6 – 1/12 – 1/16 = (8-4-3)/48 = 1/48 P:Q:R = ratio of 1 day work = 1/12:1/16 : 1/48 =4:3:1 P’s share = Rs(1200*4/8) =Rs.600 Q’s share = Rs(1200 * 3/8) =Rs.450 R’s share = Rs(1200 * 1/8) =Rs.150

The amount of energy required by the children of age between one to three years is: A. 300 K Calories B. 600 K Calories C. 1200 K Calories D. 1500 K Calories

Description : The amount of energy required by the children of age between one to three years is: A. 300 K Calories B. 600 K Calories C. 1200 K Calories D. 1500 K Calories

Last Answer : ANSWER: C

The amount of energy required by the children of age between one to three years is: A. 300 K Calories B. 600 K Calories C. 1200 K Calories D. 1500 K Calories

Description : The amount of energy required by the children of age between one to three years is: A. 300 K Calories B. 600 K Calories C. 1200 K Calories D. 1500 K Calories

Last Answer : ANSWER: C

The amount of energy required by the children of age between one to three years is: A. 300 K Calories B. 600 K Calories C. 1200 K Calories D. 1500 K Calories

Description : The amount of energy required by the children of age between one to three years is: A. 300 K Calories B. 600 K Calories C. 1200 K Calories D. 1500 K Calories

Last Answer : ANSWER: C

The amount of energy required by the children of age between one to three years is: A. 300 K Calories B. 600 K Calories C. 1200 K Calories D. 1500 K Calories

Description : The amount of energy required by the children of age between one to three years is: A. 300 K Calories B. 600 K Calories C. 1200 K Calories D. 1500 K Calories

Last Answer : ANSWER: C

When propagationspeed is multiplied by propagation time, we get the ________. A) throughput B) wavelength of thesignal C) distortionfactor D) distancea signal or bit has traveled

Description : When propagationspeed is multiplied by propagation time, we get the ________. A) throughput B) wavelength of thesignal C) distortionfactor D) distancea signal or bit has traveled

Last Answer : distancea signal or bit has traveled

Infrared range for fiber optics ∙ a. 400 – 700 nm ∙ b. 700 – 1200 nm ∙ c. 300 – 2000 nm ∙ d. 400 – 7000 nm

Description : Infrared range for fiber optics ∙ a. 400 – 700 nm ∙ b. 700 – 1200 nm ∙ c. 300 – 2000 nm ∙ d. 400 – 7000 nm

Last Answer : b. 700 – 1200 nm

ECE Board Exam March 1996 What is the transmission rate of a system for transmitting the output of a microcomputer to a line printer operating at a speed of 30 lines/minute? Assume that the line printer has 8 bits of data per character and prints out 80 characters/line. A. 800 bps B. 400 bps C. 320 bps D. 640 bps

Description : ECE Board Exam March 1996 What is the transmission rate of a system for transmitting the output of a microcomputer to a line printer operating at a speed of 30 lines/minute? Assume that the line printer has 8 bits ... and prints out 80 characters/line. A. 800 bps B. 400 bps C. 320 bps D. 640 bps

Last Answer : C. 320 bps

A device is sending out data at the rate of 2000 bps. How long does it take to send a file of 1,00,000 characters ? (A) 50 (B) 200 (C) 400 (D) 800

Description : A device is sending out data at the rate of 2000 bps. How long does it take to send a file of 1,00,000 characters ? (A) 50 (B) 200 (C) 400 (D) 800

Last Answer : (C) 400 Explanation: 1,00,000 characters = 1,00,000 x 8 bits = 8,00,000 bits 8,00,000 bits/2000 bps = 400 seconds

The maximum frame length for 10-Mbps Ethernet is ________ bytes. A) 1518 B) 1500 C) 1200 D) none of the abov

Description : The maximum frame length for 10-Mbps Ethernet is ________ bytes. A) 1518 B) 1500 C) 1200 D) none of the abov

Last Answer : 1518

The baud rate of a signal is 600 baud/second. If each signal unit carries 6 bits, then the bit rate of a signal is ................. (A) 3600 (B) 100 (C) 6/600 (D) None of the above

Description : The baud rate of a signal is 600 baud/second. If each signal unit carries 6 bits, then the bit rate of a signal is ................. (A) 3600 (B) 100 (C) 6/600 (D) None of the above

Last Answer : (A) 3600 

DMT is a modulation technique that combineselements of _______ and _______. A) FDM; TDM B) QDM; QAM C) FDM; QAM D) PSK; FSK

Description : DMT is a modulation technique that combineselements of _______ and _______. A) FDM; TDM B) QDM; QAM C) FDM; QAM D) PSK; FSK

Last Answer : FDM; QAM

_______ uses twocarriers, onein-phase andthe otherquadrature. A) ASK B) PSK C) FSK D) QAM

Description : _______ uses twocarriers, onein-phase andthe otherquadrature. A) ASK B) PSK C) FSK D) QAM

Last Answer : QAM

Quadrature amplitude modulation(QAM) isa combination of ___________. A) ASK and FSK B) ASK and PSK C) PSK and FSK D) none of the above

Description : Quadrature amplitude modulation(QAM) isa combination of ___________. A) ASK and FSK B) ASK and PSK C) PSK and FSK D) none of the above

Last Answer : ASK and PSK

Which of the following is not a digital-to-analogconversion? A) ASK B) PSK C) FSK D) AM

Description : Which of the following is not a digital-to-analogconversion? A) ASK B) PSK C) FSK D) AM

Last Answer : AM

ASK, PSK, FSK,and QAM are examples of________conversion. A) digital-to-digital B) digital-to-analog C) analog-to-analog D) analog-to-digital

Description : ASK, PSK, FSK,and QAM are examples of________conversion. A) digital-to-digital B) digital-to-analog C) analog-to-analog D) analog-to-digital

Last Answer : digital-to-analog

The data rate is sometimes calledthe ___ rate. A) baud B) bit C) signal D) none of the above

Description : The data rate is sometimes calledthe ___ rate. A) baud B) bit C) signal D) none of the above

Last Answer : bit

The signal rate is sometimes called the ____ rate. A) baud B) bit C) signal D) none of the above

Description : The signal rate is sometimes called the ____ rate. A) baud B) bit C) signal D) none of the above

Last Answer : baud

Minimum excretory urinary volume for waste products elimination during 24 hrs is (A) 200–300 ml (B) 200–400 ml (C) 500–600 ml (D) 800 ml

Description : Minimum excretory urinary volume for waste products elimination during 24 hrs is (A) 200–300 ml (B) 200–400 ml (C) 500–600 ml (D) 800 ml

Last Answer : Answer : C

In glycoproteins the carbohydrate is in the form of disaccharide units, the number of units are (A) 50–100 (B) 200–300 (C) 400–500 (D) 600–700

Description : In glycoproteins the carbohydrate is in the form of disaccharide units, the number of units are (A) 50–100 (B) 200–300 (C) 400–500 (D) 600–700

Last Answer : Answer : D

Amylose contains glucose units (A) 100–200 (B) 200–300 (C) 300–400 (D) 500–600

Description : Amylose contains glucose units (A) 100–200 (B) 200–300 (C) 300–400 (D) 500–600

Last Answer : C

The round-trip propagation delay between two earth stations through a geosynchronous satellite is A. 500 to 600 ms B. 300 to 400 ms C. 600 to 700 ms D. 400 to 500 ms

Description : The round-trip propagation delay between two earth stations through a geosynchronous satellite is A. 500 to 600 ms B. 300 to 400 ms C. 600 to 700 ms D. 400 to 500 ms

Last Answer : A. 500 to 600 ms