A weighted resistor digital to analog converter using N bits requires a total of (A) N precision resistors. (B) 2N precision resistors. (C) N + 1 precision resistors. (D) N – 1 precision resistors.

Question

A weighted resistor digital to analog converter using N bits requires a total of (A) N precision resistors. (B) 2N precision resistors. (C) N + 1 precision resistors. (D) N – 1 precision resistors.

A weighted resistor digital to analog converter using N bits requires a total of
(A) N precision resistors. (B) 2N precision resistors.
(C) N + 1 precision resistors. (D) N – 1 precision resistors.

asked Jul 19, 2021 by anonymous

1 Answer

Related questions

In a weighted-resistor digital-to-analog converter with 8-bit input, if the resistance corresponding to the MSB

Description : In a weighted-resistor digital-to-analog converter with 8-bit input, if the resistance corresponding to the MSB is 2K, what will be the resistance corresponding to the LSB? (a) 250 Ω (d) 512 KΩ (c) 256 KΩ (d) 25.5 Ω

Last Answer : In a weighted-resistor digital-to-analog converter with 8-bit input, if the resistance corresponding to the MSB is 2K, what will be the resistance corresponding to the LSB? (a) 250 Ω (d) 512 KΩ (c) 256 KΩ (d) 25.5 Ω

The conversation speed of an analog to digital converter is maximum with the following technique. (A) Dual slope AD converter. (B) Serial comparator AD converter. (C) Successive approximation AD converter. (D) Parallel comparator AD converter.

Description : The conversation speed of an analog to digital converter is maximum with the following technique. (A) Dual slope AD converter. (B) Serial comparator AD converter. (C) Successive approximation AD converter. (D) Parallel comparator AD converter.

Last Answer : (D) Parallel comparator AD converter.

In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter’s output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum quantization error. (C) Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted

Description : In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter's output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum ... Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted

Last Answer : (B) Reduce the maximum quantization error.

The A/D converter whose conversion time is independent of the number of bits is (A) Dual slope (B) Counter type (C) Parallel conversion (D) Successive approximation.

Description : The A/D converter whose conversion time is independent of the number of bits is (A) Dual slope (B) Counter type (C) Parallel conversion (D) Successive approximation.

Last Answer : Ans: C The A/D converter whose conversion time is independent of the Number of bits is Parallel conversion. (This type uses an array of comparators connected in parallel and comparators compare the input voltage at a particular ratio of the reference voltage).

The speed of conversion is maximum in (A) Successive-approximation A/D converter. (B) Parallel-comparative A/D converter. (C) Counter ramp A/D converter. (D) Dual-slope A/D converter.

Description : The speed of conversion is maximum in (A) Successive-approximation A/D converter. (B) Parallel-comparative A/D converter. (C) Counter ramp A/D converter. (D) Dual-slope A/D converter.

Last Answer : Ans: B The speed of conversion is maximum in Parallel-comparator A/D converter (Speed of conversion is maximum because the comparisons of the input voltage are carried out simultaneously.)

How many address bits are required to represent 4K memory (A) 5 bits. (B) 12 bits. (C) 8 bits. (D) 10 bits.

Description : How many address bits are required to represent 4K memory (A) 5 bits. (B) 12 bits. (C) 8 bits. (D) 10 bits.

Last Answer : (B) 12 bits.

How many address bits are required to represent a 32 K memory (A) 10 bits. (B) 12 bits. (C) 14 bits. (D) 16 bits.

Description : How many address bits are required to represent a 32 K memory (A) 10 bits. (B) 12 bits. (C) 14 bits. (D) 16 bits.

Last Answer : (D) 16 bits.

Which of the following memories stores the most number of bits (A) a 5M×8 memory. (B) a 1M × 16 memory. (C) a 5M × 4 memory. (D) a 1M ×12 memory.

Description : Which of the following memories stores the most number of bits (A) a 5M×8 memory. (B) a 1M × 16 memory. (C) a 5M × 4 memory. (D) a 1M ×12 memory.

Last Answer : Ans: A 5Mx8 = 5 x 220 x 8 = 40M (max)

Words having 8-bits are to be stored into computer memory. The number of lines required for writing into memory are (A) 1. (B) 2. (C) 4. (D) 8.

Description : Words having 8-bits are to be stored into computer memory. The number of lines required for writing into memory are (A) 1. (B) 2. (C) 4. (D) 8.

Last Answer : Ans: D Because 8-bit words required 8 bit data lines.

Which of following requires refreshing? (A) SRAM. (B) DRAM. (C) ROM. (D) EPROM.

Description : Which of following requires refreshing? (A) SRAM. (B) DRAM. (C) ROM. (D) EPROM.

Last Answer : (B) DRAM

Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it is assumed that each sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Description : Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it ... sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Last Answer : (C) 128 kbps

A `5 Omega` resistor is connected in series with a parallel combination of n resistors of `6 Omega` each. The equivalent resistance is `7 Omega`. Find

Description : A `5 Omega` resistor is connected in series with a parallel combination of n resistors of `6 Omega` each. The equivalent resistance is `7 Omega`. Find

Last Answer : A `5 Omega` resistor is connected in series with a parallel combination of n resistors of `6 Omega ... The equivalent resistance is `7 Omega`. Find n.

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

Two identical resistors are connected in parallel and consume 200 watts together. A third identical resistor is added in parallel. The total power consumed is: w) 100 watts x) 200 watts y) 300 watts z) 400 watts

Description : Two identical resistors are connected in parallel and consume 200 watts together. A third identical resistor is added in parallel. The total power consumed is: w) 100 watts x) 200 watts y) 300 watts z) 400 watts

Last Answer : ANSWER: Y -- 300 WATTS

Which numbering format is the basis for digital electronic circuitry? 76) A) decimal B) BCD C) octal D) binary

Description : Which numbering format is the basis for digital electronic circuitry? 76) A) decimal B) BCD C) octal D) binary

Last Answer : D) binary

The chief reason why digital computers use complemented subtraction is that it (A) Simplifies the circuitry. (B) Is a very simple process. (C) Can handle negative numbers easily. (D) Avoids direct subtraction.

Description : The chief reason why digital computers use complemented subtraction is that it (A) Simplifies the circuitry. (B) Is a very simple process. (C) Can handle negative numbers easily. (D) Avoids direct subtraction.

Last Answer : Ans: C Using complement method negative numbers can also be subtracted.

In digital ICs, Schottky transistors are preferred over normal transistors because of their (A) Lower Propagation delay. (B) Higher Propagation delay. (C) Lower Power dissipation. (D) Higher Power dissipation.

Description : In digital ICs, Schottky transistors are preferred over normal transistors because of their (A) Lower Propagation delay. (B) Higher Propagation delay. (C) Lower Power dissipation. (D) Higher Power dissipation.

Last Answer : Ans: A Lower propagation delay as shottky transistors reduce the storage time delay by preventing the transistor from going deep into saturation.

The digital logic family which has the lowest propagation delay time is (A) ECL (B) TTL (C) CMOS (D) PMOS

Description : The digital logic family which has the lowest propagation delay time is (A) ECL (B) TTL (C) CMOS (D) PMOS

Last Answer : Ans: A The digital logic family which has the lowest propagation delay time is ECL (Lowest propagation delay time is possible in ECL because the transistors are used in difference amplifier configuration, in which they are never driven into saturation and thereby the storage time is eliminated).

The digital logic family which has minimum power dissipation is (A) TTL (B) RTL (C) DTL (D) CMOS

Description : The digital logic family which has minimum power dissipation is (A) TTL (B) RTL (C) DTL (D) CMOS

Last Answer : (D) CMOS The digital logic family which has minimum power dissipation is CMOS. (CMOS being an unipolar logic family, occupy a very small fraction of silicon Chip area)

What is a Digital-to-Analog Converter (DAC) in Arduino?

Description : What is a Digital-to-Analog Converter (DAC) in Arduino?

Last Answer : A Digital-to-Analog Converter (DAC) in Arduino is a component that converts digital signals into analog signals, such as to control the output voltage to a motor or a speaker.

What is an Analog-to-Digital Converter (ADC) in Arduino?

Description : What is an Analog-to-Digital Converter (ADC) in Arduino?

Last Answer : An Analog-to-Digital Converter (ADC) in Arduino is a component that converts analog signals, such as temperature or light, into digital signals that can be processed by the microcontroller.

In a synchronous modem, the digital-to-analog converter transmits signal to the a. equilizer b. modulator c. demodulator d. terminal e. none of aobve

Description : In a synchronous modem, the digital-to-analog converter transmits signal to the a. equilizer b. modulator c. demodulator d. terminal e. none of aobve

Last Answer : equilizer

It is the ratio of the largest possible magnitude to the smallest possible magnitude that can be decoded by the digital-to-analog converter in the receiver.

Description : It is the ratio of the largest possible magnitude to the smallest possible magnitude that can be decoded by the digital-to-analog converter in the receiver.

Last Answer : Dynamic range

The number of comparators required in a 3-bit comparator type analog to digital converter is

Description : The number of comparators required in a 3-bit comparator type analog to digital converter is A) 2 B) 3 C) 7 D) 8

Last Answer : Number of comparators =2^n -1= 2^3 -1=7

A digital voltmeter uses an A/D converter which needs a start pulse, uses an analog comparator and has a...

Description : A digital voltmeter uses an A/D converter which needs a start pulse, uses an analog comparator and has a relatively fixed conversion time independent of the applied voltage. The A/D ... Successive Approximation Converter .b) Digital Ramp Converter c) Digital Slope Converter d) All the above

Last Answer : A digital voltmeter uses an A/D converter which needs a start pulse, uses an analog comparator and has a relatively fixed conversion time independent of the applied voltage. The A/D converter is : - Successive Approximation Converter

A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the...

Description : A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the input code 1010: (1) 0.3125 V (2) 3.125 V (3) 0.78125 V (4) –3.125 V

Last Answer : 3.125V

What is Analog to Digital Converter (ADC) ?

Description : What is Analog to Digital Converter (ADC) ?

Last Answer : Analog to Digital Converter (ADC) Analog quantity may be voltage, temperature, sound, speed, audio etc. it is information or signal. ... digital form), digital speedometer (converts analog speed into digital form) etc.

Digital to Analog Converter (DAC)

Description : Digital to Analog Converter (DAC)

Last Answer : Digital to Analog Converter (DAC) Digital means binary (1 0) and 1 and 0 may be true and false or on and off or high and low. Analog means continuous signal or information ... wave. Phase Shift Keying (PSK) is transmit digital data by changing the phase of carrier wave.

In troubleshooting a circuit in a console, you find that a resistor may be faulty. Which of the precautions listed must be observed when using an ohmmeter to carry out this test? A. Correct polarity must be observed, connecting the red lead to the banded end of the resistor. B. Meter leads must be twisted to cancel the leads' magnetic fields. C. The meter must be placed in series with the resistor and the circuit. D. The resistor's circuit must be de-energized and at least one end of the component isolated.

Description : In troubleshooting a circuit in a console, you find that a resistor may be faulty. Which of the precautions listed must be observed when using an ohmmeter to carry out this test? A. Correct polarity ... D. The resistor's circuit must be de-energized and at least one end of the component isolated.

Last Answer : Answer: D

Bits can be sent over guided and unguided media as analog signal by ___________ a. digital modulation b. amplitude modulation c. frequency modulation d. phase modulation

Description : Bits can be sent over guided and unguided media as analog signal by ___________ a. digital modulation b. amplitude modulation c. frequency modulation d. phase modulation

Last Answer : a. digital modulation

Write down the drawback of weighted D/A converter.

Description : Write down the drawback of weighted D/A converter.

Last Answer : The main disadvantage of binary weighted D/A converter is the requirement of wide range of resister values.As the length of the binary word is increased .the range of resister values needed also increases.

In a 5 bit weighted resistor D/A converters, the resistor value corresponding to LSB is 40 kΩ, and the resistor

Description : In a 5 bit weighted resistor D/A converters, the resistor value corresponding to LSB is 40 kΩ, and the resistor value corresponding to MSB will be (A) 0.4 kΩ (B) 3 kΩ (C) 2.8 kΩ (D) 2.5 kΩ

Last Answer : In a 5 bit weighted resistor D/A converters, the resistor value corresponding to LSB is 40 kΩ, and the resistor value corresponding to MSB will be 2.5 kΩ

The information in ROM is stored (A) By the user any number of times. (B) By the manufacturer during fabrication of the device. (C) By the user using ultraviolet light. (D) By the user once and only once.

Description : The information in ROM is stored (A) By the user any number of times. (B) By the manufacturer during fabrication of the device. (C) By the user using ultraviolet light. (D) By the user once and only once.

Last Answer : (B) By the manufacturer during fabrication of the device.

The output of a JK flipflop with asynchronous preset and clear inputs is ‘1’. The output can be changed to ‘0’ with one of the following conditions. (A) By applying J = 0, K = 0 and using a clock. (B) By applying J = 1, K = 0 and using the clock. (C) By applying J = 1, K = 1 and using the clock. (D) By applying a synchronous preset input.

Description : The output of a JK flipflop with asynchronous preset and clear inputs is 1'. The output can be changed to 0' with one of the following conditions. (A) By applying J = 0, K = 0 and using a clock. (B) ... (C) By applying J = 1, K = 1 and using the clock. (D) By applying a synchronous preset input.

Last Answer : Ans: C Preset state of JK Flip-Flop =1 With J=1 K=1 and the clock next state will be complement of the present state.

1’s complement representation of decimal number of -17 by using 8 bit representation is (A) 1110 1110 (B) 1101 1101 (C) 1100 1100 (D) 0001 0001

Description : 1’s complement representation of decimal number of -17 by using 8 bit representation is (A) 1110 1110 (B) 1101 1101 (C) 1100 1100 (D) 0001 0001

Last Answer : (A) 1110 1110

The access time of ROM using bipolar transistors is about (A) 1 sec (B) 1 msec (C) 1 µsec (D) 1 nsec.

Description : The access time of ROM using bipolar transistors is about (A) 1 sec (B) 1 msec (C) 1 µsec (D) 1 nsec.

Last Answer : Ans: C The access time of ROM using bipolar transistors is about 1 µ sec.

Data can be changed from special code to temporal code by using (A) Shift registers (B) counters (C) Combinational circuits (D) A/D converters.

Description : Data can be changed from special code to temporal code by using (A) Shift registers (B) counters (C) Combinational circuits (D) A/D converters.

Last Answer : Ans: A Data can be changed from special code to temporal code by using Shift Registers. (A Register in which data gets shifted towards left or right when clock pulses are applied is known as a Shift Register.)

The IEEE-754 double-precision format to represent floating point numbers, has a length of ........... bits. (A) 16 (B) 32 (C) 48 (D) 64

Description : The IEEE-754 double-precision format to represent floating point numbers, has a length of ........... bits. (A) 16 (B) 32 (C) 48 (D) 64

Last Answer : (D) 64

`6Omega` and `12Omega` resistors are connected in parallel. This combination is connected in series with 10 V battery and `6 Omega` resistor. What is

Description : `6Omega` and `12Omega` resistors are connected in parallel. This combination is connected in series with 10 V battery and `6 Omega` resistor. What is

Last Answer : `6Omega` and `12Omega` resistors are connected in parallel. This combination is connected in series with 10 V battery and ... 4 V B. 16 V C. 2 D. 8 V

Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by the `6 Omega` resistor is

Description : Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by the `6 Omega` resistor is

Last Answer : Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by ... 384 W B. 616 W C. 1500 W D. 1800 W

While troubleshooting a circuit in an engine room central control console, a resistor is suspected of being faulty. Which of the following precautions must be observed if an ohmmeter is to be used to check its value? A. Correct polarity must be observed because reverse bias will damage the component. B. Meter leads must not be twisted so as to cancel out the individual magnetic fields. C. Resistor's circuit must be de-energized and at least one end of the component isolated. D. The meter case must be grounded prior to attaching the leads.

Description : While troubleshooting a circuit in an engine room central control console, a resistor is suspected of being faulty. Which of the following precautions must be observed if an ohmmeter is to be used to ... of the component isolated. D. The meter case must be grounded prior to attaching the leads.

Last Answer : Answer: C

One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. Heating of capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Description : One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. ... capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Last Answer : B. Heating of capacitor in the oscillator

A resistor is handed to you for identification with the following color code: the first band is blue, followed by gray, green, gold, and brown. What is the resistor’s value?

Description : A resistor is handed to you for identification with the following color code: the first band is blue, followed by gray, green, gold, and brown. What is the resistor’s value?

Last Answer : 6,800,000 ohms (6.8 mega ohms), with 5% tolerance, and a 1% reliability level.

Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Description : Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Last Answer : 25 ohms

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1 = 2.1 ohms RT= 2.1 + 7.8 = 9.9 ohms IT = V/R = 24/9.9 = 2.4 A Veq= R I = 2.1 2 ... 7.8 = 12.096 w = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

if we want to find current across a specific resistor in parallel circuits we take the value of other resistor but which resistance to take if there are four resistors

Description :

Last Answer : By using current rule

Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor

Description : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

Last Answer : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

Three resistors of 4 Ω, 6 Ω and 9 Ω are connected in parallel. Which resistor consumes the maximum power?

Description : Three resistors of 4 Ω, 6 Ω and 9 Ω are connected in parallel. Which resistor consumes the maximum power? (A) 4 Ω (B) 6 Ω (C) 9 Ω (D) 17 Ω

Last Answer : (c) 9 ohm

In precision theodolite traverse if included angles are read twice and the mean reading accepted using both verniers having a least count of 30". Assuming the instrument to be in perfect adjustment, linear measurements correct to 6 mm per 30 metre tape duly corrected for temperature, slope and sag, the angular error of closure not to exceed (where n is the number of traverse legs) (A) 50" n(B) 30" n(C) 60" n (D) None of these

Description : In precision theodolite traverse if included angles are read twice and the mean reading accepted using both verniers having a least count of 30". Assuming the instrument to be in perfect adjustment, linear measurements correct to 6 mm per ... legs) (A) 50" n (B) 30" n (C) 60" n (D) None of these

Last Answer : (A) 50" n

Define Asynchronous sequential circuit?

Description : Define Asynchronous sequential circuit?

Last Answer : In asynchronous sequential circuits change in input signals can affect memory element at any instant of time.

anonymous · Answer 1 · 2021-07-19T10:03:20+0000

Answer :

(A) N precision resistors.

answered Jul 19, 2021 by anonymous

A weighted resistor digital to analog converter using N bits requires a total of (A) N precision resistors. (B) 2N precision resistors. (C) N + 1 precision resistors. (D) N – 1 precision resistors.

Please log in or register to add a comment.

Please log in or register to answer this question.

1 Answer

Answer :

Please log in or register to add a comment.

Related questions