The digital logic family which has minimum power dissipation is (A) TTL (B) RTL (C) DTL (D) CMOS

The digital logic family which has minimum power dissipation is (A) TTL (B) RTL  (C) DTL (D) CMOS
by

1 Answer

Answer :

(D) CMOS
The digital logic family which has minimum power dissipation is CMOS.
 (CMOS being an unipolar logic family, occupy a very small fraction of silicon Chip
area)
by

Related questions

Which of following consume minimum power (A) TTL. (B) CMOS. (C) DTL. (D) RTL.

Description : Which of following consume minimum power (A) TTL. (B) CMOS. (C) DTL. (D) RTL.

Last Answer : Ans: B CMOS consumes minimum power as in CMOS one p-MOS & one n-MOS transistors are connected in complimentary mode, such that one device is ON & one is OFF.

The digital logic family which has the lowest propagation delay time is (A) ECL (B) TTL (C) CMOS (D) PMOS

Description : The digital logic family which has the lowest propagation delay time is (A) ECL (B) TTL (C) CMOS (D) PMOS

Last Answer : Ans: A The digital logic family which has the lowest propagation delay time is ECL (Lowest propagation delay time is possible in ECL because the transistors are used in difference amplifier configuration, in which they are never driven into saturation and thereby the storage time is eliminated).

Which of the following is the fastest logic? (A) ECL (B) TTL (C) CMOS (D) LSI

Description : Which of the following is the fastest logic? (A) ECL (B) TTL (C) CMOS (D) LSI

Last Answer : (A) ECL

Which of the following is the fastest logic (A) TTL (B) ECL (C) CMOS (D) LSI

Description : Which of the following is the fastest logic (A) TTL (B) ECL (C) CMOS (D) LSI

Last Answer : Ans: B ECL is the fastest logic family of all logic families. (High speeds are possible in ECL because the transistors are used in difference amplifier configuration, in which they are never driven into saturation and thereby the storage time is eliminated.

What are RTL, DTL, and TTL examples of?

Description : What are RTL, DTL, and TTL examples of?

Last Answer : Logic families.

CMOS circuits consume power (A) Equal to TTL (B) Less than TTL (C) Twice of TTL (D) Thrice of TTL

Description : CMOS circuits consume power (A) Equal to TTL (B) Less than TTL (C) Twice of TTL (D) Thrice of TTL

Last Answer : Ans: B As in CMOS one device is ON & one is Always OFF so power consumption is low.

CMOS circuits are extensively used for ON-chip computers mainly because of their extremely (A) low power dissipation. (B) high noise immunity. (C) large packing density. (D) low cost.

Description : CMOS circuits are extensively used for ON-chip computers mainly because of their extremely (A) low power dissipation. (B) high noise immunity. (C) large packing density. (D) low cost.

Last Answer : Ans: C Because CMOS circuits have large packing density.

The MSI chip 7474 is (A) Dual edge triggered JK flip-flop (TTL). (B) Dual edge triggered D flip-flop (CMOS). (C) Dual edge triggered D flip-flop (TTL). (D) Dual edge triggered JK flip-flop (CMOS).

Description : The MSI chip 7474 is (A) Dual edge triggered JK flip-flop (TTL). (B) Dual edge triggered D flip-flop (CMOS). (C) Dual edge triggered D flip-flop (TTL). (D) Dual edge triggered JK flip-flop (CMOS).

Last Answer : Ans: C MSI chip 7474 dual edge triggered D Flip-Flop.

Which TTL logic gate is used for wired ANDing (A) Open collector output (B) Totem Pole (C) Tri state output (D) ECL gates

Description : Which TTL logic gate is used for wired ANDing (A) Open collector output (B) Totem Pole (C) Tri state output (D) ECL gates

Last Answer : Ans: A Open collector output.

The logic 0 level of a CMOS logic device is approximately (A) 1.2 volts (B) 0.4 volts (C) 5 volts (D) 0 volts

Description : The logic 0 level of a CMOS logic device is approximately (A) 1.2 volts (B) 0.4 volts (C) 5 volts (D) 0 volts

Last Answer : Ans: D CMOS logic low level is 0 volts approx.

In digital ICs, Schottky transistors are preferred over normal transistors because of their (A) Lower Propagation delay. (B) Higher Propagation delay. (C) Lower Power dissipation. (D) Higher Power dissipation.

Description : In digital ICs, Schottky transistors are preferred over normal transistors because of their (A) Lower Propagation delay. (B) Higher Propagation delay. (C) Lower Power dissipation. (D) Higher Power dissipation.

Last Answer : Ans: A Lower propagation delay as shottky transistors reduce the storage time delay by preventing the transistor from going deep into saturation.

The commercially available 8-input multiplexer integrated circuit in the TTL family is (A) 7495. (B) 74153. (C) 74154. (D) 74151.

Description : The commercially available 8-input multiplexer integrated circuit in the TTL family is (A) 7495. (B) 74153. (C) 74154. (D) 74151.

Last Answer : Ans: B MUX integrated circuit in TTL is 74153.

In a CMOS inverter, the dynamic power dissipation

Description : In a CMOS inverter, the dynamic power dissipation  (A) decreases with power supply voltage  (B) increases with power supply voltage  (C) is independent of power supply voltage  (D) is zero

Last Answer : In a CMOS inverter, the dynamic power dissipation  increases with power supply voltage 

TTL logic family is most popularly used industries because it

Description : TTL logic family is most popularly used industries because it  1.provides greater operating speed 2.has a good fan in & fan out 3.has easy interface with other digital circuitry 4.all the above 

Last Answer : It is a basically a bipolar circuit which has TTL band hate fan fan out

Define combinational logic

Description : Define combinational logic

Last Answer : When logic gates are connected together to produce a specified output for certain specified combinations of input variables, with no storage involved, the resulting circuit is called combinational logic.

A full adder logic circuit will have (A) Two inputs and one output. (B) Three inputs and three outputs. (C) Two inputs and two outputs. (D) Three inputs and two outputs.

Description : A full adder logic circuit will have (A) Two inputs and one output. (B) Three inputs and three outputs. (C) Two inputs and two outputs. (D) Three inputs and two outputs.

Last Answer : Ans: D A full adder circuit will add two bits and it will also accounts the carry input generated in the previous stage. Thus three inputs and two outputs (Sum and Carry) are there.

Karnaugh map is used for the purpose of (A) Reducing the electronic circuits used. (B) To map the given Boolean logic function. (C) To minimize the terms in a Boolean expression. (D) To maximize the terms of a given a Boolean expression.

Description : Karnaugh map is used for the purpose of (A) Reducing the electronic circuits used. (B) To map the given Boolean logic function. (C) To minimize the terms in a Boolean expression. (D) To maximize the terms of a given a Boolean expression.

Last Answer : (C) To minimize the terms in a Boolean expression.

A universal logic gate is one, which can be used to generate any logic function. Which of the following is a universal logic gate? (A) OR (B) AND (C) XOR (D) NAND

Description : A universal logic gate is one, which can be used to generate any logic function. Which of the following is a universal logic gate? (A) OR (B) AND (C) XOR (D) NAND

Last Answer : Ans: D NAND can generate any logic function.

In a positive logic system, logic state 1 corresponds to (A) positive voltage (B) higher voltage level (C) zero voltage level (D) lower voltage level

Description : In a positive logic system, logic state 1 corresponds to (A) positive voltage (B) higher voltage level (C) zero voltage level (D) lower voltage level

Last Answer : (B) higher voltage level We decide two voltages levels for positive digital logic. Higher voltage represents logic 1 & a lower voltage represents logic 0.

The output of a logic gate is 1 when all its inputs are at logic 0. the gate is either (A) a NAND or an EX-OR (B) an OR or an EX-NOR (C) an AND or an EX-OR (D) a NOR or an EX-NOR

Description : The output of a logic gate is 1 when all its inputs are at logic 0. the gate is either (A) a NAND or an EX-OR (B) an OR or an EX-NOR (C) an AND or an EX-OR (D) a NOR or an EX-NOR

Last Answer : (D) a NOR or an EX-NOR

Define following terms related to logic families : (i) Noise Margin (ii) FAN-OUT (iii) Propagation delay (iv) Power dissipation

Description : Define following terms related to logic families : (i) Noise Margin (ii) FAN-OUT (iii) Propagation delay (iv) Power dissipation

Last Answer : i) Noise immunity is measured in terms of noise margin. High state Noise margin = VNH = VOH(min) - VIH(min) Low state Noise margin = VNL = VIL(max) - VOL(max) i) The fan-out is defined as the ... logical 0 state (HIGH to LOW) iii) Average power dissipation is defined as PD(avg) = ICC(avg) * VCC

Which numbering format is the basis for digital electronic circuitry? 76) A) decimal B) BCD C) octal D) binary

Description : Which numbering format is the basis for digital electronic circuitry? 76) A) decimal B) BCD C) octal D) binary

Last Answer : D) binary

A weighted resistor digital to analog converter using N bits requires a total of (A) N precision resistors. (B) 2N precision resistors. (C) N + 1 precision resistors. (D) N – 1 precision resistors.

Description : A weighted resistor digital to analog converter using N bits requires a total of (A) N precision resistors. (B) 2N precision resistors. (C) N + 1 precision resistors. (D) N – 1 precision resistors.

Last Answer : (A) N precision resistors.

The conversation speed of an analog to digital converter is maximum with the following technique. (A) Dual slope AD converter. (B) Serial comparator AD converter. (C) Successive approximation AD converter. (D) Parallel comparator AD converter.

Description : The conversation speed of an analog to digital converter is maximum with the following technique. (A) Dual slope AD converter. (B) Serial comparator AD converter. (C) Successive approximation AD converter. (D) Parallel comparator AD converter.

Last Answer : (D) Parallel comparator AD converter.

The chief reason why digital computers use complemented subtraction is that it (A) Simplifies the circuitry. (B) Is a very simple process. (C) Can handle negative numbers easily. (D) Avoids direct subtraction.

Description : The chief reason why digital computers use complemented subtraction is that it (A) Simplifies the circuitry. (B) Is a very simple process. (C) Can handle negative numbers easily. (D) Avoids direct subtraction.

Last Answer : Ans: C Using complement method negative numbers can also be subtracted.

What are the advantages of TTL (transistor transistor logic)?

Description : What are the advantages of TTL (transistor transistor logic)?

Last Answer : To know about the advantages of TTL logic family, one should have a basic idea about RTL, DTL etc. Diode logic (DL) uses diodes to implement logical functions like AND and OR. But the disadvantage is that it can ... delay offered by them, the logic levels may sometimes change i. e. 0 t0 1 or 1 to 0.

What are the types of TTL logic?

Description : What are the types of TTL logic?

Last Answer : 1. Open collector output 2. Totem-Pole Output 3. Tri-state output.

Design Y=AB.CD using CMOS logic.

Description : Design Y=AB.CD using CMOS logic.

Last Answer : Y=AB.CD using CMOS logic

How much does an advertisement at TV2 and RTL Klub cost?

Description : Does anyone know how much a say a 10-second ad can cost?

Last Answer : It depends on how many times it will be broadcast on TV, etc. An advertisement is about 40,000-50,000 HUF, and that's what it costs to pay for it, not only once a week, but about 4 times a day.

what does a cmos digital camera do?

Description : what does a cmos digital camera do?

Last Answer : Cmos digital cameras can do quite a few things. This URL address tells you everything that there is about Cmos digital cameras and how everything works.

What are the benefits of a cmos digital camera?

Description : What are the benefits of a cmos digital camera?

Last Answer : As a cmos camera can refer to many different types of cameras, it's hard to answer this. Mainly, cmos cameras are less expensive to manufactiure, resulting in cheaper cameras in general. That's about all I can tell you, sorry!

Build using minimum number of CMOS gates.

Description : Build using minimum number of CMOS gates. Three input NAND gate. Two input NOR gate Three input NOR gate Two input AND gate Two input OR gate

Last Answer : Three input NAND gate. Two input NOR gate Three input NOR gate Two input AND gate Two input OR gate

When the conduction current density and displacement current density are same, the dissipation factor will be a) Zero b) Minimum c) Maximum d) Unity

Description : When the conduction current density and displacement current density are same, the dissipation factor will be a) Zero b) Minimum c) Maximum d) Unity

Last Answer : d) Unity

What is Est Outpt L4 Dtl F?

Description : What is Est Outpt L4 Dtl F?

Last Answer : Need answer

What does est outpt L4 Dtl H&E Mod Complx Code #99214?

Description : What does est outpt L4 Dtl H&E Mod Complx Code #99214?

Last Answer : I am not sure what is being asked here

Define Asynchronous sequential circuit?

Description : Define Asynchronous sequential circuit?

Last Answer : In asynchronous sequential circuits change in input signals can affect memory element at any instant of time.

Define synchronous sequential circuit

Description : Define synchronous sequential circuit

Last Answer : In synchronous sequential circuits, signals can affect the memory elements only at discrete instant of time.

What are the different types of shift type?

Description : What are the different types of shift type?

Last Answer : There are five types. They are, Serial In Serial Out Shift Register Serial In Parallel Out Shift Register Parallel In Serial Out Shift Register Parallel In Parallel Out Shift Register Bidirectional Shift Register

Define shift registers.

Description : Define shift registers.

Last Answer : The binary information in a register can be moved from stage to stage within the register or into or out of the register upon application of clock ... arithmetic and logic operations used in microprocessors. This gives rise to group of registers called shift registers.

Define registers.

Description : Define registers.

Last Answer : A register is a group of flip-flops flip-flop can store one bit information. So an n-bit register has a group of n flip-flops and is capable of storing any binary information/number containing n-bits.

What is a master-slave flip-flop?

Description : What is a master-slave flip-flop?

Last Answer : A master-slave flip-flop consists of two flip-flops where one circuit serves as a master and the other as a slave.

What is edge-triggered flip-flop?

Description : What is edge-triggered flip-flop?

Last Answer : The problem of race around condition can solved by edge triggering flip flop. The term edge triggering means that the flip-flop changes state either at the positive ... negative edge of the clock pulse and it is sensitive to its inputs only at this transition of the clock.

Define race around condition.

Description : Define race around condition.

Last Answer : In JK flip-flop output is fed back to the input. Therefore change in the output results change in the input. Due to this in the positive half of the clock pulse if both J and K are high then output toggles continuously. This condition iscalled ‘race around condition’.

What is the operation of T flip-flop?

Description : What is the operation of T flip-flop?

Last Answer : T flip-flop is also known as Toggle flip-flop. • When T=0 there is no change in the output. • When T=1 the output switch to the complement state (ie) the output toggles.

What is the operation of JK flip-flop?

Description : What is the operation of JK flip-flop?

Last Answer : When K input is low and J input is high the Q output of flip-flop is set. When K input is high and J input is low the Q output of flip-flop is reset. When both the inputs ... are high it is possible to set or reset the flip-flop (ie) the output toggle on the next positive clock edge.

What is the operation of D flip-flop?

Description : What is the operation of D flip-flop?

Last Answer : In D flip-flop during the occurrence of clock pulse if D=1, the output Q is set and if D=0, the output is reset.

What are the different types of flip-flop?

Description : What are the different types of flip-flop?

Last Answer : There are various types of flip flops. Some of them are mentioned below they are, RS flip-flop SR flip-flop D flip-flop JK flip-flop T flip-flop

Define Flip flop.

Description : Define Flip flop.

Last Answer : The basic unit for storage is flip flop. A flip-flop maintains its output state either at 1 or 0 until directed by an input signal to change its state.

What are the classification of sequential circuits?

Description : What are the classification of sequential circuits?

Last Answer : The sequential circuits are classified on the basis of timing of their signals into two types. They are, 1)Synchronous sequential circuit. 2)Asynchronous sequential circuit.

What do you mean by comparator

Description : What do you mean by comparator

Last Answer : A comparator is a special combinational circuit designed primarily to compare the relative magnitude of two binary numbers.