In a strain measuring device, using a strain gauge, the output quantity is ....

In a strain measuring device, using a strain gauge, the output quantity is 

A) Voltage B) resistance C) Impedance D) either A) or B)
by

1 Answer

Answer :

In a strain measuring device, using a strain gauge, the output quantity is Voltage

by

Related questions

Measuring force without a strain gauge?

Description : Measuring force without a strain gauge?

Last Answer : answer:Do you want to know the force or the pressure at the tip? Will this be changing rapidly? Let's assume you want the force first and you will calculate the pressure from the force and ... device and work out the force from the assembly's resonant freq. Lots of possibilities. Not enough detail.

The Semiconductor strain gauges typically have much higher gauge factors than those of metallic strain

Description : The Semiconductor strain gauges typically have much higher gauge factors than those of metallic strain gauges, primarily due to : (A) higher temperature sensitivity (B) higher Poisson’s ratio (C) higher piezoresitive coefficient (D) higher magnetostrictive coefficient

Last Answer : The Semiconductor strain gauges typically have much higher gauge factors than those of metallic strain gauges, primarily due to : higher piezoresitive coefficient

Which of the listed devices may be used as a digital device? A. variable resistor B. diode C. strain gauge D. thermistor

Description : Which of the listed devices may be used as a digital device? A. variable resistor B. diode C. strain gauge D. thermistor

Last Answer : Answer: B

A device for measuring relative humidity is called: a. A dew point analyzer b. An R. H. gauge c. An aspirating gauge d. A psychrometer e. A chronometer

Description : A device for measuring relative humidity is called: a. A dew point analyzer b. An R. H. gauge c. An aspirating gauge d. A psychrometer e. A chronometer

Last Answer : Answer: D

Sketch DC signal conditioning circuit for pressure measurement using strain gauge. Justify it.

Description : Sketch DC signal conditioning circuit for pressure measurement using strain gauge. Justify it.

Last Answer : Diagram: Figure: DC signal conditioning circuit for pressure measurement using strain gauge Where, Rg= strain gauge resistance. Explanation: In order to measure strain with ... millivolts output per volt input. The Wheatstone circuit is also well suited for temperature compensation.

__________ circuit is most commonly used to measure strain with the help of a strain gauge. (A) Ballast (B) Voltage balancing potentiometric (C) Simple current sensitive (D) None of these

Description : __________ circuit is most commonly used to measure strain with the help of a strain gauge. (A) Ballast (B) Voltage balancing potentiometric (C) Simple current sensitive (D) None of these

Last Answer : Option B

How to Measure a Strain Gauge

Description : How to Measure a Strain Gauge

Last Answer : How to Measure a Strain Gauge There are several ways to measure strain. The most common is to use a strain gauge. In laymen's terms, a strain gauge is a device whose electrical ... who supply all the necessary strain gauges and materials from connection tags, to binding adhesives and training.

State function of strain gauge. Give its types and explain working of any one type of it.

Description : State function of strain gauge. Give its types and explain working of any one type of it.

Last Answer : Function of strain gauge: - ➢ The strain gauge is a passive, resistive transducer which converts the mechanical elongation and compression into a resistance change. ➢ This change in ... change in resistivity. 3. Silicon and germanium are used as resistive material for semiconductor gauges

Describe strain gauge with labelled diagram.

Description : Describe strain gauge with labelled diagram.

Last Answer : A Strain gauge is a sensor whose resistance varies with applied force. It converts force, pressure, tension, weight, etc., into a change in electrical resistance which can then be measured. When external ... to the applied strain. So, the voltmeter can be calibrated in terms of strain or force. 

Define : i) Strain gauge ii) Gauge factor

Description : Define : i) Strain gauge ii) Gauge factor

Last Answer : i) Strain gauge is a resistance transducer whose resistance varies with applied force; It converts force, pressure, tension, weight, etc., into a change in electrical resistance which can then be measured ... is defined as the ratio of per unit change in resistance to per unit change in length 

Explain working of resistance strain gauge

Description : Explain working of resistance strain gauge

Last Answer : Principle working: Strain gauge is a passive, versatile transducer and it is often used for measuring weight, pressure, force and displacement .They sense the strain produced in a wire due to applied ... , allowing the strain measured to be related to the applied stress and hence the force applied.

Explain in brief the working principle of strain gauge. Define gauge factor and list out types of strain gauges.

Description : Explain in brief the working principle of strain gauge. Define gauge factor and list out types of strain gauges.

Last Answer : If a metal conductor is stretched or compressed, the resistance changes as both length and diameter change. There is a change in the value of resistivity of the conductor also when it is ... metal film strain gauges 6. Diffused metal strain gauges 7. Sputter deposited thin metal strain gauge

How strain gauge is used for pressure measurement, explain?

Description : How strain gauge is used for pressure measurement, explain?

Last Answer : strain gauge: - strain gauge is used for pressure measurement as one of the arm of a wheatstones' bridge, the pressure is applied to the strain gauge through diaphragm elastic pressure sensor.

Dummy strain gauge is used in conjunction with the main strain gauge to _____.

Description : Dummy strain gauge is used in conjunction with the main strain gauge to _____.

Last Answer : Dummy strain gauge is used in conjunction with the main strain gauge to compensate temperature effects.

Gauge factor of strain gauge is defined as the ratio of per unit change in the ______.

Description :  Gauge factor of strain gauge is defined as the ratio of per unit change in the ______.

Last Answer :  Gauge factor of strain gauge is defined as the ratio of per unit change in the resistance to the per unit change in the length of the element.

The advantage of a semiconductor strain gauge cover the wire round strain gauge is that

Description : The advantage of a semiconductor strain gauge cover the wire round strain gauge is that

Last Answer : The advantage of a semiconductor strain gauge cover the wire round strain gauge is that it is more sensitive

If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge

Description : If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge factor is :  (A) 2.8 (B) 2.6 (C) 4.6 (D) 3.6

Last Answer : If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge factor is : 4.6

A strain gauge is a passive transducer and is employed for converting

Description : A strain gauge is a passive transducer and is employed for converting   (a) Pressure into change in resistance (b) Force into displacement (c) Mechanical displacement into a change of resistance (d) None of the above 

Last Answer : A

Most appropriate instrument for measurement of internal and external diameter of a tube is A. vernier callipers B. micrometer screw gauge C. meter rule D. measuring tape

Description : Most appropriate instrument for measurement of internal and external diameter of a tube is A. vernier callipers B. micrometer screw gauge C. meter rule D. measuring tape

Last Answer : vernier callipers

__________ is used for measuring the static pressure exerted on the wall by a fluid flowing parallel to the wall in a pipeline. (A) Venturimeter (B) Pressure gauge(C) Pitot tube(D) Orificemeter

Description : __________ is used for measuring the static pressure exerted on the wall by a fluid flowing parallel to the wall in a pipeline. (A) Venturimeter (B) Pressure gauge (C) Pitot tube (D) Orificemeter

Last Answer : (C) Pitot tube

A component whose property changes when there is a change in any physical quantity of a device is A. processor B. sensoC. output deviceD. portable devicer

Description : A component whose property changes when there is a change in any physical quantity of a device is A. processor B. sensor C. output device D. portable device

Last Answer : sensor

When measuring strain, ballast circuit use a capacitor to act as a high pass filter. This is done when:

Description : When measuring strain, ballast circuit use a capacitor to act as a high pass filter. This is done when:  a) Static strain are being measured b) Dynamic strain are being measured c) Both Static and dynamic strain are being measured d) None of the above

Last Answer : When measuring strain, ballast circuit use a capacitor to act as a high pass filter. This is done when: Dynamic strain are being measured

Which one of the following is a nondimensional quantity? (1) Gas constant (2) Strain (3) Co-efficient of viscosity (4) Plank's constant

Description : Which one of the following is a nondimensional quantity? (1) Gas constant (2) Strain (3) Co-efficient of viscosity (4) Plank's constant

Last Answer : (2) Strain Explanation: A dimensionless quantity is simply a quantity that has no units and therefore no dimensions. A ratio between two numbers is a non-dimensional or dimensionless quantity. ... in dimension over original dimension has no dimensional formula. So it is a. dimensionless quantity.

Dimensions of strain are A. [L] B. [M] [L]-1 [T]-2 C. [L]-1 D. It's a dimensionless quantity

Description : Dimensions of strain are A. [L] B. [M] [L]-1 [T]-2 C. [L]-1 D. It's a dimensionless quantity

Last Answer : It's a dimensionless quantity

Which of the following is a dimensionless quantity? (a) Shear stress (b) Poison’s ratio (c) Strain (d) Both (b) and (c)

Description : Which of the following is a dimensionless quantity? (a) Shear stress (b) Poison’s ratio (c) Strain (d) Both (b) and (c)

Last Answer : (d) Both (b) and (c)

Which one of the following is a non-dimensional quantity? (1) Gas constant (2) Strain (3) Co-efficient of viscocity (4) Plank’s constant

Description : Which one of the following is a non-dimensional quantity? (1) Gas constant (2) Strain (3) Co-efficient of viscocity (4) Plank’s constant

Last Answer : Strain

I don’t want to spend any money for any grounding device when I can make one myself. All I have to do it get a ground rod, some 20 gauge wire, and then wrap the wire around my ankle or foot at night.

Description : I don’t want to spend any money for any grounding device when I can make one myself. All I have to do it get a ground rod, some 20 gauge wire, and then wrap the wire around my ankle or foot at night.

Last Answer : You can certainly do it. People have done it any times. However, it is not particularly comfortable. You could possibly cut off circulation if you wrap the wire too tight around your extremity. Secondly, a sharp end on a wire wrapped around the ankle could tear the sheet.

A boy presses a side of a blue pencil to a side of a yellow pencil, holding both pencils vertically. One inch of the pressed side of the blue pencil, measuring from its lower end, is smeared with paint. The yellow pencil is held steady while the boy slides the blue pencil down 1 inch, continueing to press it against the yellow one. He returns the blue pencil to its former position, then again it slides down 1 inch. He continues until he has lowered the blue pencil 5 times and raised it 5 times- 10 moves in all.Supposed that during this time the paint neither dries nor diminishes in quantity. How many inches of each pencil will be sneared with paint after the tenth move? -Riddles

Description : A boy presses a side of a blue pencil to a side of a yellow pencil, holding both pencils vertically. One inch of the pressed side of the blue pencil, measuring from its lower end, is smeared ... in quantity. How many inches of each pencil will be sneared with paint after the tenth move? -Riddles

Last Answer : At the start, 1inch of the yellow pencil gets smeared with wet paint. As the blue pencil is moved downward, a second inch of the blue pencils smears a second inch of the yellow pencil. Each pair ... of moves will smear 5 inches. This together with the initial inch, makes 6 inches for each pencil.

Measuring quantity of mercury?

Description : Measuring quantity of mercury?

Last Answer : Flask

For measuring an unknown electrical quantity, select the meter with

Last Answer : For measuring an unknown electrical quantity, select the meter with Highest range and work down.

The pressure and velocity at the throat of a Venturi tube, measuring the flow of a liquid, are related to the

Description : The pressure and velocity at the throat of a Venturi tube, measuring the flow of a liquid, are related to the upstream pressure and velocity, respectively, as follows: (A) Pressure is lower but ... velocity is lower (C) Both pressure and velocity are lower (D) Pressure and velocity are identical

Last Answer : The pressure and velocity at the throat of a Venturi tube, measuring the flow of a liquid, are related to the upstream pressure and velocity, respectively, as follows: (A) Pressure is lower but ... lower (C) Both pressure and velocity are lower (D) Pressure and velocity are identical

The following quantity is not required in the calculation of Q of a cavity resonator

Description : The following quantity is not required in the calculation of Q of a cavity resonator  a) Energy stored b) Power dissipated c) Loss in radiation d) Dimensions of the cavity

Last Answer : The following quantity is not required in the calculation of Q of a cavity resonator  a) Energy stored b) Power dissipated c) Loss in radiation d) Dimensions of the cavity

The difference between the indicated value and the true value of a quantity is known as

Last Answer : The difference between the indicated value and the true value of a quantity is known as Dynamic error.

Which of the following is a scalar quantity?

Description : Which of the following is a scalar quantity? a) Electric displacement density b) Potential in electric field c) Electric field strength d) None of the above

Last Answer : b) Potential in electric field

Which of the following methods is/are used for measuring national income? (a) Output method ; (b) Expenditure method ; (c) Income method ; (d) All of (a), (b) and (c) above.

Description : Which of the following methods is/are used for measuring national income? (a) Output method ; (b) Expenditure method ; (c) Income method ; (d) All of (a), (b) and (c) above.

Last Answer : (d) All of (a), (b) and (c) above.

What is the name of the device for measuring density ?

Description : What is the name of the device for measuring density ?

Last Answer : The name of the instrument for measuring density is hydrometer.

What is the name of the blood pressure measuring device in human body ?

Description : What is the name of the blood pressure measuring device in human body ?

Last Answer : : Sphygmomanometer is the name of the blood pressure measuring device in human body

What is the name of the device measuring small current flow ?

Description : What is the name of the device measuring small current flow ?

Last Answer : The name of the instrument used to measure small current flow is galvanometer

What is the name of the air pressure measuring device ?

Last Answer : : Barometer is an instrument for measuring air pressure.

What is the name of the device for measuring the density of milk ?

Last Answer : The name of the instrument for measuring the density of milk is lactometer

What is the name of the heart rate measuring device ?

Last Answer : Cardiograph is a device that measures the heart rate.

Measuring pressure at home with a digital device

Description : How should the hand be when measuring pressure? When I put it to my head or toes, it always shows differently. I don't have a guide anymore.

Last Answer : For example here - http://www.sportstatus.cz/postava---navody/jak-merit-krevni-tlak - is a general guide on how to measure your pressure. It is important to proceed in the same way each time so that the measurement conditions do not change. ;-)

What is the name of the device used for measuring ground movement?

Description : What is the name of the device used for measuring ground movement?

Last Answer : Need answer

What is a weather balloon device for measuring air pressure temperature and relative humidity is called?

Description : What is a weather balloon device for measuring air pressure temperature and relative humidity is called?

Last Answer : A+ Radiosonde

The most common water flow measuring device which measures water flow in open conduit is

Description : The most common water flow measuring device which measures water flow in open conduit is

Last Answer : Ans.Parshall/Venturi flume

A thermostat is a device for (a) switching off an electrical appliance (b) measuring temperature (c) regulating temperature (d) producing heat

Description : A thermostat is a device for (a) switching off an electrical appliance (b) measuring temperature (c) regulating temperature (d) producing heat

Last Answer : Ans:(c)

Ondometer is a - (1) Measuring instrument for distance covered by motor wheels (2) Measuring instrument for frequency of electromagnetic waves (3) Device for measuring sound intensity (4) Measuring instrument for electric power

Description : Ondometer is a - (1) Measuring instrument for distance covered by motor wheels (2) Measuring instrument for frequency of electromagnetic waves (3) Device for measuring sound intensity (4) Measuring instrument for electric power

Last Answer : (2) Measuring instrument for frequency of electromagnetic waves

The device used for measuring the wavelength of X-rays is – (1) G.M. Counter (2) Cyclotron (3) Bragg Spectrometer (4) Mass Spectrometer

Description : The device used for measuring the wavelength of X-rays is – (1) G.M. Counter (2) Cyclotron (3) Bragg Spectrometer (4) Mass Spectrometer

Last Answer : (3) Bragg Spectrometer Explanation: Bragg Spectrometer is an instrument used to analyze crystal structure by using X-rays. In it, a beam of collimated X-rays strikes the crystal, and a detector measures the angles and intensities of the reflected beam.

What device measures rf power by measuring the heat the rf power generates? A. Calorimeter B. Goniometer C. Spectrum meter D. Oscilloscope

Description : What device measures rf power by measuring the heat the rf power generates? A. Calorimeter B. Goniometer C. Spectrum meter D. Oscilloscope

Last Answer : A. Calorimeter