Chain drives are stable for a) Constant speed ratio between parallel shafts b) Distance between centre to centre is moderate c) Dirty and dusty environment d) All of the above

Chain drives are stable for  
a) Constant speed ratio between parallel shafts
b) Distance between centre to centre is moderate
c) Dirty and dusty environment  
d) All of the above
by

1 Answer

Answer :

d) All of the above
by

Related questions

Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Description : Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Last Answer : a) gears

Worm gears are used for transmitting power between two shafts a)at right angle to each other and cannot intersect each other b) at right angle to each other and can intersect each other c)at angle to each other d)shafts on different plane

Description : Worm gears are used for transmitting power between two shafts a)at right angle to each other and cannot intersect each other b) at right angle to each other and can intersect each other c)at angle to each other d)shafts on different plane

Last Answer : a)at right angle to each other and cannot intersect each other

Spiral gear Is used to transmit power between two shafts place at: a)An angle to each other b)In different planes c)Both(a)and(b) d)None of the above

Description : Spiral gear Is used to transmit power between two shafts place at: a)An angle to each other b)In different planes c)Both(a)and(b) d)None of the above

Last Answer : c)Both(a)and(b)

The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance between the speed pick up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Function of idler pully are a. to increase the angle of contact of belt on pully b. maintain belt tension as belt stretches c. canter to centre distance remain same d. all the above

Description : Function of idler pully are a. to increase the angle of contact of belt on pully b. maintain belt tension as belt stretches c. canter to centre distance remain same d. all the above

Last Answer : d. all the above

What is the value for centrifugal torque for maximum power transmission in belt drives a) ½ maximum torque b) 2/3 maximum torque c) ¾ maximum torque d) None of the above

Description : What is the value for centrifugal torque for maximum power transmission in belt drives a) ½ maximum torque b) 2/3 maximum torque c) ¾ maximum torque d) None of the above

Last Answer : d) None of the above

V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above

Description : V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Description : The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Last Answer : (c)reel speed index

Tension on the slack side in chain drive is A)more than on tight side. B)less than on tight side. C)zero. D)equal to tight

Description : Tension on the slack side in chain drive is A)more than on tight side. B)less than on tight side. C)zero. D)equal to tight

Last Answer : C)zero

Tension on slack side in case of chain drive a) Lesser than on tight side b) Greater than on tight side c) Zero d) Equal to that on tight side

Description : Tension on slack side in case of chain drive a) Lesser than on tight side b) Greater than on tight side c) Zero d) Equal to that on tight side

Last Answer : c) Zero

.The land side of a mould board plough is made of: A. Malleable iron B. Forged steel C. C45 steel D. Soft Centre steel

Description : .The land side of a mould board plough is made of: A. Malleable iron B. Forged steel C. C45 steel D. Soft Centre steel

Last Answer : D. Soft Centre steel

The landside of a mould board plough is made of: a) Malleable iron b) Forged steel c) C45 steel d) Soft centre steel

Description : The landside of a mould board plough is made of: a) Malleable iron b) Forged steel c) C45 steel d) Soft centre steel

Last Answer : d) Soft centre steel

Mould board are usually made from a. Soft centre steel b. Hardened carbon steel c. Chilled cast iron d. Mild steel

Description : Mould board are usually made from a. Soft centre steel b. Hardened carbon steel c. Chilled cast iron d. Mild steel

Last Answer : a. Soft centre steel

Scouring will occur as long as a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face b) Frictional resistance at soil tool interface is more than the resistance at parallel soil-soil inter face c) Soil-metal friction is more than angle of soil shearing resistance d) None of the above

Description : Scouring will occur as long as a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face b) Frictional resistance at soil tool interface is more than ... c) Soil-metal friction is more than angle of soil shearing resistance d) None of the above

Last Answer : a) Frictional resistance at soil tool interface is less than the resistance at parallel soil-soil inter face

Desired tension in an open belt drive system can be maintained (without changing center to center distance between two pulley)by using A)ldler pulley. B)slide rail C) Tilting angle. D)none of the above

Description : Desired tension in an open belt drive system can be maintained (without changing center to center distance between two pulley)by using A)ldler pulley. B)slide rail C) Tilting angle. D)none of the above

Last Answer : A)ldler pulley

One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle

Description : One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle

Last Answer : . Requires less pedal force to stop the vehicle

The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow

Description : The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow

Last Answer : D. The number of furrow openers x distance between two furrow

Center of resistence of a mould board plow less at distance equal to A. 1/4th the size of plow from the share wing B. 3/4th the size of plow from the share wing C. 2/3th the size of plow from the share wing D. 1/3th the size of plow from the share wing

Description : Center of resistence of a mould board plow less at distance equal to A. 1/4th the size of plow from the share wing B. 3/4th the size of plow from the share wing C. 2/3th the size of plow from the share wing D. 1/3th the size of plow from the share wing

Last Answer : B. 3/4th the size of plow from the share wing

In check rowing the seed spacing is a. constant b. continuous c. same as the rows d. none of these

Description : In check rowing the seed spacing is a. constant b. continuous c. same as the rows d. none of these

Last Answer : c. same as the rows

The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above

Description : The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above

Last Answer : E. Automatic draft control system

tractors are generally fitted with: A)sliding mesh gear box B)constant mesh gear box C)both (a) & (b) D)synchromesh gear box

Description : tractors are generally fitted with: A)sliding mesh gear box B)constant mesh gear box C)both (a) & (b) D)synchromesh gear box

Last Answer : A)sliding mesh gear box

A Tillage implement moving at a constant velocity is subjected to a) Force of gravity b) Soil force (resistance) c) Pull of mower d) All of the above

Description : A Tillage implement moving at a constant velocity is subjected to a) Force of gravity b) Soil force (resistance) c) Pull of mower d) All of the above

Last Answer : d) All of the above

Pick out the wrong statement (A) The concentric atmosphere layer just above troposphere is called stratosphere, which is rich in ozone (B) Mesosphere is characterised by very low atmospheric pressure and low temperature (C) Troposphere is a dusty zone containing water vapor and clouds (D) The radio waves used in the long distance radio communication are reflected back to earth by stratosphere

Description : Pick out the wrong statement (A) The concentric atmosphere layer just above troposphere is called stratosphere, which is rich in ozone (B) Mesosphere is characterised by very low atmospheric ... radio waves used in the long distance radio communication are reflected back to earth by stratosphere

Last Answer : (D) The radio waves used in the long distance radio communication are reflected back to earth by stratosphere

A test harness is a A. A high level document describing the principles, approach and major objectives of the organization regarding testing B. A distance set of test activities collected into a manageable phase of a project C. A test environment comprised of stubs and drives needed to conduct a test D. A set of several test cases for a component or system under test

Description : A test harness is a A. A high level document describing the principles, approach and major objectives of the organization regarding testing B. A distance set of test activities collected into a manageable phase ... conduct a test D. A set of several test cases for a component or system under test

Last Answer : C. A test environment comprised of stubs and drives needed to conduct a test

Suggested or recommended difference in mass to power ratio between ballasted and unballasted tractor is of the order a)10kg/PTO KW b)6kg/PTO kw c)20kg/PTO kw d)30kg/PTO kw

Description : Suggested or recommended difference in mass to power ratio between ballasted and unballasted tractor is of the order a)10kg/PTO KW b)6kg/PTO kw c)20kg/PTO kw d)30kg/PTO kw

Last Answer : b)6kg/PTO kw

In an epicycle gear reduction unit, the ratio of the number of teeth of the internal gears to the sun gear is: a) 3:1 b) 4:1 c) 2.5:1 d) 4.5:1

Description : In an epicycle gear reduction unit, the ratio of the number of teeth of the internal gears to the sun gear is: a) 3:1 b) 4:1 c) 2.5:1 d) 4.5:1

Last Answer : b) 4:1

pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement

Description : pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement

Last Answer : c) Both (a) and (b)

Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above

Description : Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above

Last Answer : (a) Angular velocity of straw Walker to angular velocity of threshing drum

.Increase the grain/non grain ratio on the shoe tends to the shoe losses (a) Decreases (b) Increases (c) Decrease or increase (d) Equal

Description : .Increase the grain/non grain ratio on the shoe tends to the shoe losses (a) Decreases (b) Increases (c) Decrease or increase (d) Equal

Last Answer : (d) Equal

Increase in grain/non grain ratio on the straw Walker losses (a) Decrease (b) Increases (c) Unltered (d) None of the above

Description : Increase in grain/non grain ratio on the straw Walker losses (a) Decrease (b) Increases (c) Unltered (d) None of the above

Last Answer : (b) Increases

Smaller tension ratio result in.... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Both (c) & (b) (d) Excessive belt slippage

Description : Smaller tension ratio result in.... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Both (c) & (b) (d) Excessive belt slippage

Last Answer : (c) Both (c) & (b)

310- Larger tension ratio result in... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Excessive belt slippage (d) Increase belt life

Description : 310- Larger tension ratio result in... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Excessive belt slippage (d) Increase belt life

Last Answer : (c) Excessive belt slippage

Stroke bore ratio for tractor engine is (a) 1.25 (b) 1.45 (c) 1.75 (d) 2.00

Description : Stroke bore ratio for tractor engine is (a) 1.25 (b) 1.45 (c) 1.75 (d) 2.00

Last Answer : (a) 1.25

Increasing the grain/non-grain ratio on shoe tends to _________ the shoe losses a) Decrease b) Increase c)Decrease or increase d) Equal

Description : Increasing the grain/non-grain ratio on shoe tends to _________ the shoe losses a) Decrease b) Increase c)Decrease or increase d) Equal

Last Answer : c)Decreas

Increase in grain/non-grain ratio on the straw walker, _____the straw walker losses a) Decrease b) Increase c)Unaltered d) None of the above

Description : Increase in grain/non-grain ratio on the straw walker, _____the straw walker losses a) Decrease b) Increase c)Unaltered d) None of the above

Last Answer : b) Increase

The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Description : The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Last Answer : 35

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : a) 300-400rpm

Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : d) 1100-1200rpm

Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Last Answer : c) 600-800rpm

main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops more current. C. To prevent building up of high voltage in a circuit. D. None of the above

Description : main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops ... . C. To prevent building up of high voltage in a circuit. D. None of the above

Last Answer : B. To safeguard against flow of high currents to battery when armature develops more current.

Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at high speed. C. To permit the generation to deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Description : Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at ... deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Last Answer : A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces.

Optimum operating speed of rotavator is a)20-150rpm b)150-350rpm c)350-500rpm d) >500rpm

Description : Optimum operating speed of rotavator is a)20-150rpm b)150-350rpm c)350-500rpm d) >500rpm

Last Answer : d) >500rpm

Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Description : Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Last Answer : c. Both (a) and (b)

Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Description : Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Last Answer : (B) Maximum brake horse power output

V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above

Description : V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above

Last Answer : c. both (a) and (b)

Slip of belt is responsible for A. Reduction is speed B. Reduction in power C. Reduction in belt life D. All of the above

Description : Slip of belt is responsible for A. Reduction is speed B. Reduction in power C. Reduction in belt life D. All of the above

Last Answer : D. All of the above

Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Description : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Last Answer : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)

Description : Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)

Last Answer : B. CI=[E/(N+E) ]×100

Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec

Description : Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec

Last Answer : B. 18-20m/sec