Description : .Increase the grain/non grain ratio on the shoe tends to the shoe losses (a) Decreases (b) Increases (c) Decrease or increase (d) Equal
Last Answer : (d) Equal
Description : Increase in grain/non grain ratio on the straw Walker losses (a) Decrease (b) Increases (c) Unltered (d) None of the above
Last Answer : (b) Increases
Description : Increase in grain/non-grain ratio on the straw walker, _____the straw walker losses a) Decrease b) Increase c)Unaltered d) None of the above
Last Answer : b) Increase
Description : Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above
Last Answer : (a) Cylinder losses
Description : Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above
Last Answer : a) Cylinder losses
Description : Increase amount of non-grain material on the straw walker _______ the walker losses a) Decreases b) Increases c) Unaffected d) Equal
Description : .Incresase amount of the non grain material on the straw Walker the walker (a) Decrease (b) Increase (c) Unaffected (d) Equal
Description : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above
Last Answer : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above
Description : 349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss
Last Answer : (d) Gathering loss
Description : At smaller disc angles , the draft tends to increase in disc plough because of a) Greater contact area between furrow wall and the convex side of the disc b) Increase in the side draft c) Greater throw of the soil d) All of the above
Last Answer : a) Greater contact area between furrow wall and the convex side of the disc
Description : .Fandem wheels are preferred over dual wheels because a) they tends to reduce load on an area by50% b)they tends to reduce soil contact pressure c)reduces sub soil compact ness pressure d)none of the above
Last Answer : a) they tends to reduce load on an area by50%
Description : Which end of disc harrow tends to penetrate more deeply a) Concave b) Convex c) Rear d) Front
Last Answer : a) Concave
Description : pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement
Last Answer : c) Both (a) and (b)
Description : Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above
Last Answer : (a) Increase threshing efficiency
Description : Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above
Last Answer : d) All of the above
Description : Shoe type furrow openers especially suited to A. Stoney and root infested fields B. Poorly prepared bed in trashy soils C. Hard and sricky soil with considerable amount of mulch and debris D. All of the above
Last Answer : B. Poorly prepared bed in trashy soils
Description : Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss
Last Answer : (b) Shoe loss
Description : Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss
Last Answer : (b) walker loss(rack loss)
Description : Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss
Last Answer : (a)cylinder loss
Description : Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm
Last Answer : a)400-550 rpm
Description : swirl plate in the cone nozzle is provided to. a. Impart rotational motion to the liquid passing through it. b. To increase the droplet size. c. To decrease the droplet size. d. To increase the spray angle.
Last Answer : a. Impart rotational motion to the liquid passing through it.
Description : .Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely
Last Answer : c) No affect
Description : Durability of the fertilizer increases with a) Increase in the kinetic angle of repose b) Decrease in the kinetic angle of repose c) Decrease in the speed of the forward travel d) None of the above
Last Answer : b) Decrease in the kinetic angle of repose
Description : In a disc plough with the increase in the disk angle, the transverse component of reaction will a)Increase b) Decrease c) Unaffected d) None of the above
Last Answer : a)Increase
Description : Total mechanical losses ( frictional losses , pumping loss in intake and exhaust and power accessories) will amount to a.10-20 % ihp b.2-10 % ihp c.20-30 % ihp d.30 -50 % ihp
Last Answer : a.10-20 % ihp
Description : ncreased amount of non-grain material on the shoe appreciably______ the shoe loss a) Decreases b) Increases c) Unaltered d) Equal
Last Answer : b) Increases
Description : 310- Larger tension ratio result in... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Excessive belt slippage (d) Increase belt life
Last Answer : (c) Excessive belt slippage
Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder
Last Answer : a.) Decreasing cylinder peripheral speed.
Description : Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle
Last Answer : a)Increasing disc angle
Description : Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above
Last Answer : M. Cylinder peripheral speed
Description : The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.
Last Answer : 35
Description : Improved uniformity is obtained if seed tube is inclined rear ward at _________ with vertical. a)5-15° b)15-30° c)30-40° d)40-50
Last Answer : b)15-30°
Description : Vasoactive drugs which cause the arteries and veins to dilate, thereby shunting much of the intravascular volume to the periphery and causing a reduction in preload and afterload include agents ... Furosemide (Lasix) Furosemide (Lasix) is a loop diuretic that reduces intravascular fluid volume.
Last Answer : a) Sodium nitroprusside (Nipride) Sodium nitroprusside is used in the treatment of cardiogenic shock.
Description : In hydrodynamic lubrication, film thickness remains unaffected by change in speeds. a) True b) Increase with increase in speed c) Decrease with increase in speed d) Disappear as the speed tends to infinty
Last Answer : b) Increase with increase in speed
Description : Suggested or recommended difference in mass to power ratio between ballasted and unballasted tractor is of the order a)10kg/PTO KW b)6kg/PTO kw c)20kg/PTO kw d)30kg/PTO kw
Last Answer : b)6kg/PTO kw
Description : In an epicycle gear reduction unit, the ratio of the number of teeth of the internal gears to the sun gear is: a) 3:1 b) 4:1 c) 2.5:1 d) 4.5:1
Last Answer : b) 4:1
Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above
Description : Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above
Last Answer : (a) Angular velocity of straw Walker to angular velocity of threshing drum
Description : Smaller tension ratio result in.... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Both (c) & (b) (d) Excessive belt slippage
Last Answer : (c) Both (c) & (b)
Description : Stroke bore ratio for tractor engine is (a) 1.25 (b) 1.45 (c) 1.75 (d) 2.00
Last Answer : (a) 1.25
Description : V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above
Description : Chain drives are stable for a) Constant speed ratio between parallel shafts b) Distance between centre to centre is moderate c) Dirty and dusty environment d) All of the above
Description : The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index
Last Answer : (c)reel speed index
Description : Function of idler pully are a. to increase the angle of contact of belt on pully b. maintain belt tension as belt stretches c. canter to centre distance remain same d. all the above
Last Answer : d. all the above
Description : A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced
Last Answer : a. Seed is increase
Description : When V-belt drive is used a safety device, its performance is affected by a) Variation in belt tention b) Increase in coefficient of friction as belt slippage increase c) Both (a) and (b) d) None of the above
Description : raft increases with increase in forward speed for most of the implement, mainly due to a) More rapid acceleration of any soil particles that is moved appreciably b) More working width c) Increased working depth d) Draft decreases with increase in speed of implement
Last Answer : a) More rapid acceleration of any soil particles that is moved appreciably
Description : Penetration of disc plough can be improved by a) Increase disc angle b) Decreasing tilt angle c) Both (a) and (b) d) None of the above
Last Answer : b) Decreasing tilt angle
Description : A slat mould board scours better than a solid mould board because of smaller contact area resulting in a) Reduction of adhesive force b) Increase in soil pressure c) Both (a) and (b) d) None of the above
Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height
Last Answer : a)Increase the co-efficient of friction between crop stalk machine