Number of piston rings on piston varies between A. 1-3 B. 3-7 C. 7 D. 12 E. >12

Number of piston rings on piston varies between
A. 1-3
B. 3-7
C. 7
D. 12
E. >12
by

1 Answer

Answer :

B. 3-7
by

Related questions

hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder

Description : hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder

Last Answer : (b) number of power stroke per minute for all cylinders

Piston speed for high speed engine is (a) 300-500 m/min (b) 100-300 m/min (c) 500-700 m/min (d) >700m/min

Description : Piston speed for high speed engine is (a) 300-500 m/min (b) 100-300 m/min (c) 500-700 m/min (d) >700m/min

Last Answer : (a) 300-500 m/min

power of absorbing type hydraulic dynamometer varies as a) cube of rpm b) fifth power of the diameter c) none of the above d) both (a) and (b)

Description : power of absorbing type hydraulic dynamometer varies as a) cube of rpm b) fifth power of the diameter c) none of the above d) both (a) and (b)

Last Answer : d) both (a) and (b)

In standard disc plow the tilk angel varies between: A.30-40 ° B.40-45° C.20-25° D.2-3°

Description : In standard disc plow the tilk angel varies between: A.30-40 ° B.40-45° C.20-25° D.2-3°

Last Answer : C.20-25°

Can I replace the piston rings?

Description : Is it very difficult to replace the piston rings at the roof? Mustang 50.

Last Answer : I also changed them for the first time and I did it. The worst was the loosening of the screws on his head.

New piston rings for java 50.

Description : I replaced the piston 50 Mustang piston rings and now the head is overheating terribly. I just drive for 2 minutes and it's overheated that I'm smoking and the bike can't start. After cooling, it ... and rides again for 2 minutes before overheating. He's been doing it since I put new piston rings.

Last Answer : How much have you driven since the exchange? And - you just changed the rings - or the whole set (+ cut)? Anyway - now you are running the engine, so you should lubricate more (approx. 1:20), do ... anti-knock gap, the tightness of the cylinder head ... And don't forget to clean the exhaust. ;-)

Operating pressure of power operated sprayer E. 1-7 kg/cm2 F. 10-20 kg/cm2+ G. 20-55 kg/cm2 H. >55 kg/cm2

Description : Operating pressure of power operated sprayer E. 1-7 kg/cm2 F. 10-20 kg/cm2+ G. 20-55 kg/cm2 H. >55 kg/cm2

Last Answer : G. 20-55 kg/cm2

Operating pressure of the hand operated sprayer is E. 20-55 kg/cm2 F. 1-7 kg/cm2 G. 10-20 kg/cm2 H. >55 kg/cm2

Description : Operating pressure of the hand operated sprayer is E. 20-55 kg/cm2 F. 1-7 kg/cm2 G. 10-20 kg/cm2 H. >55 kg/cm2

Last Answer : F. 1-7 kg/cm2

Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec

Description : Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec

Last Answer : B. 18-20m/sec

The estimated useful life of diesel engine is: A)8 years b)10 years C)12 years d)14years

Description : The estimated useful life of diesel engine is: A)8 years b)10 years C)12 years d)14years

Last Answer : b)10 years

Hand operated sprayer are operated at a pressure (kg/cm2) a) 1-7 b) 7-10 c)10-20 d) 20-55

Description : Hand operated sprayer are operated at a pressure (kg/cm2) a) 1-7 b) 7-10 c)10-20 d) 20-55

Last Answer : a) 1-7

Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions

Description : Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions

Last Answer : f. Dried hard soils

A traction fitted with diesel engine will have good slogging ability as lugging ability if it has a reserve of a.500 rpm d.200 rpm c.300 rpm e.1000 rpm

Description : A traction fitted with diesel engine will have good slogging ability as lugging ability if it has a reserve of a.500 rpm d.200 rpm c.300 rpm e.1000 rpm

Last Answer : a.500 rpm

Worm gear are used for transmitting power between two Shaft Inclined at e. At right angle to each other and axes can intersect f. At right angle to each other but axis cannot intersect each other g. At right angle to each other and in different planes h. None of the above

Description : Worm gear are used for transmitting power between two Shaft Inclined at e. At right angle to each other and axes can intersect f. At right angle to each other but axis cannot intersect each other g. At right angle to each other and in different planes h. None of the above

Last Answer : f. At right angle to each other but axis cannot intersect each other

Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)

Description : Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)

Last Answer : B. CI=[E/(N+E) ]×100

Formula for established plant to the seed sown based on the delivery rate (kg/ha) is A. CI=[(E×10000) /(D×W) ]×100 B. CI=[E/(N+E) ]×100 C. Both (A) and (B) D. None of (A) and (B)

Description : Formula for established plant to the seed sown based on the delivery rate (kg/ha) is A. CI=[(E×10000) /(D×W) ]×100 B. CI=[E/(N+E) ]×100 C. Both (A) and (B) D. None of (A) and (B)

Last Answer : A. CI=[(E×10000) /(D×W) ]×100

The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above

Description : The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above

Last Answer : E. Automatic draft control system

Juice extraction capacity of vertical three roller type bullock down sugercane crusher E. 50-70% F. 70-90% G. 90-100% H. 30-50%

Description : Juice extraction capacity of vertical three roller type bullock down sugercane crusher E. 50-70% F. 70-90% G. 90-100% H. 30-50%

Last Answer : E. 50-70%

Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above

Description : Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above

Last Answer : F. Capacity of chaff cutters

Length of cut for silage ranges from E. 2-4 cm F. 5-10 cm G. 15-20 cm H. 20-25 cm

Description : Length of cut for silage ranges from E. 2-4 cm F. 5-10 cm G. 15-20 cm H. 20-25 cm

Last Answer : E. 2-4 cm

Speed of power operated machine chaff cutter is E. 35 rpm F. 50 rpm G. 600-1000 rpm H. None of the above

Description : Speed of power operated machine chaff cutter is E. 35 rpm F. 50 rpm G. 600-1000 rpm H. None of the above

Last Answer : G. 600-1000 rpm

An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of operation is 2.0kmph, the area covered (ha), in 8-11day is given by: A. 1.85/1000k B. 28.8 x 10-2k C. k/6.56 D. 1.762k

Description : An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of operation is 2.0kmph, the area covered (ha), in 8-11day is given by: A. 1.85/1000k B. 28.8 x 10-2k C. k/6.56 D. 1.762k

Last Answer : B. 28.8 x 10-2k

Application rate of sprayer is affected by a. forward of speed b. number of nozzle c. rate of discharge d. all of the above

Description : Application rate of sprayer is affected by a. forward of speed b. number of nozzle c. rate of discharge d. all of the above

Last Answer : d. all of the above

.The number of knives on powered chaff cutter a) 2-6 b) 1-2 c) 5-10 d) 10-20

Description : .The number of knives on powered chaff cutter a) 2-6 b) 1-2 c) 5-10 d) 10-20

Last Answer : a) 2-6

Size of MB plow is determined by (a) depth of cut (b) width of cut (c) number of accessories (d) none of the above

Description : Size of MB plow is determined by (a) depth of cut (b) width of cut (c) number of accessories (d) none of the above

Last Answer : (b) width of cut

In an epicycle gear reduction unit, the ratio of the number of teeth of the internal gears to the sun gear is: a) 3:1 b) 4:1 c) 2.5:1 d) 4.5:1

Description : In an epicycle gear reduction unit, the ratio of the number of teeth of the internal gears to the sun gear is: a) 3:1 b) 4:1 c) 2.5:1 d) 4.5:1

Last Answer : b) 4:1

An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of the operation is 2.0kmph then the area covered (ha), in 8 hr day is given by: a) 1.85/1000k b) 28.8 * 10-2k c) k/6.456 d) 1.762k

Description : An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of the operation is 2.0kmph then the area covered (ha), in 8 hr day is given by: a) 1.85/1000k b) 28.8 * 10-2k c) k/6.456 d) 1.762k

Last Answer : b) 28.8 * 10-2k

The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow

Description : The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow

Last Answer : D. The number of furrow openers x distance between two furrow

Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Description : Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

nging the speed of feed mechanism (b) The number of knives on feed mechanism (c) Changing speed of cutter head (d) All of the above

Description : nging the speed of feed mechanism (b) The number of knives on feed mechanism (c) Changing speed of cutter head (d) All of the above

Last Answer : (d) All of the above

A dash pot consists of a cylinder 10 cm in diameter in which slides a piston 12 cm long having a radial clearance of 1 mm. The cylinder is filled with oil having a viscosity of 1 poise. What will be the resistance offered by the piston to sliding with a velocity of 3 cm/sec a.1090 kg b.100 kg c.10900 kg d.10 kg e.50 kg

Description : A dash pot consists of a cylinder 10 cm in diameter in which slides a piston 12 cm long having a radial clearance of 1 mm. The cylinder is filled with oil having a viscosity of 1 poise. What will be the resistance offered ... with a velocity of 3 cm/sec a.1090 kg b.100 kg c.10900 kg d.10 kg e.50 kg

Last Answer : c. 10900 kg

verticalsuctioninmouldboardploughis______whereashorizontalsuctionis______

Description : verticalsuctioninmouldboardploughis______whereashorizontalsuctionis______

Last Answer : .0.3to0.5cm,0.5cm

Byincreasingdiskangle,depthpenetration_____beoverwithofcut_______

Description : Byincreasingdiskangle,depthpenetration_____beoverwithofcut_______

Last Answer : .decreases,increases

A paddy transplanter uses either root wash type seedlings or __________ seedlings.

Description : A paddy transplanter uses either root wash type seedlings or __________ seedlings.

Last Answer : soil bearing

An indigenous plough cuts a _________furrow cross sect

Description : An indigenous plough cuts a _________furrow cross sect

Last Answer : Trapizoidal

The unit of filter medium resistance is________

Description : The unit of filter medium resistance is________

Last Answer : L^-1

The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Description : The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Last Answer : 35

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

In sprayers , operating pressures below ___________Kpa are undesirable for hydraulic nozzles other than flooding type

Description : In sprayers , operating pressures below ___________Kpa are undesirable for hydraulic nozzles other than flooding type

Last Answer : 140

Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : a) 300-400rpm

Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : d) 1100-1200rpm

Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Last Answer : c) 600-800rpm

Air output of a duster is given by formula a) Q= 60×A×V b)Q= 60×A×(2GH/Y) c) Q= 240×A×h d) all of the above

Description : Air output of a duster is given by formula a) Q= 60×A×V b)Q= 60×A×(2GH/Y) c) Q= 240×A×h d) all of the above

Last Answer : d) all of the above

Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Description : Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Last Answer : a) gears

Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above

Description : Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above

Last Answer : d) all of the above

Superchargers are driven by A. Electric current from the battery B. Exhaust gases from engine C. Direct connection with the engine power D. None of the above

Description : Superchargers are driven by A. Electric current from the battery B. Exhaust gases from engine C. Direct connection with the engine power D. None of the above

Last Answer : C. Direct connection with the engine power

Turbo chargers are driven by A. Direct connection with engine power B. Exhaust gases from engine C. Electric current from the battery D. None of the above

Description : Turbo chargers are driven by A. Direct connection with engine power B. Exhaust gases from engine C. Electric current from the battery D. None of the above

Last Answer : B. Exhaust gases from engine

Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%

Description : Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%

Last Answer : A. 10-20%

.When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Last Answer : B. L-head

Utility index is a indication of A. Work machine contact hours B. Wear out life of machine C. Operating cost of machine D. Reliability of machine working

Description : Utility index is a indication of A. Work machine contact hours B. Wear out life of machine C. Operating cost of machine D. Reliability of machine working

Last Answer : A. Work machine contact hours