Can I replace the piston rings?

Is it very difficult to replace the piston rings at the roof? Mustang 50.
by

1 Answer

Answer :

I also changed them for the first time and I did it. The worst was the loosening of the screws on his head.
by

Related questions

New piston rings for java 50.

Description : I replaced the piston 50 Mustang piston rings and now the head is overheating terribly. I just drive for 2 minutes and it's overheated that I'm smoking and the bike can't start. After cooling, it ... and rides again for 2 minutes before overheating. He's been doing it since I put new piston rings.

Last Answer : How much have you driven since the exchange? And - you just changed the rings - or the whole set (+ cut)? Anyway - now you are running the engine, so you should lubricate more (approx. 1:20), do ... anti-knock gap, the tightness of the cylinder head ... And don't forget to clean the exhaust. ;-)

Number of piston rings on piston varies between A. 1-3 B. 3-7 C. 7 D. 12 E. >12

Description : Number of piston rings on piston varies between A. 1-3 B. 3-7 C. 7 D. 12 E. >12

Last Answer : B. 3-7

Engineering Piston Question?

Description : Engineering Piston Question?

Last Answer : I don’t believe you have enough information to figure this out. Normally those pistons provide damping that slows the action down. A gas charge by itself would make the piston move very rapidly so damping must be added. The damping properties need to be known.

The piston of a steam engine moves in S.H.M. The crank rotates at 180 r.p.m. and the stroke length is 2 metres. The linear velocity of the piston when it is at a distance of 1 metre from the centre is a.8.88 m/sec b.16.32 m/sec c.5.88 m/sec d.8.16 m/sec e.Zero

Description : The piston of a steam engine moves in S.H.M. The crank rotates at 180 r.p.m. and the stroke length is 2 metres. The linear velocity of the piston when it is at a distance of 1 metre from the centre is a.8.88 m/sec b.16.32 m/sec c.5.88 m/sec d.8.16 m/sec e.Zero

Last Answer : e. Zero

A dash pot consists of a cylinder 10 cm in diameter in which slides a piston 12 cm long having a radial clearance of 1 mm. The cylinder is filled with oil having a viscosity of 1 poise. What will be the resistance offered by the piston to sliding with a velocity of 3 cm/sec a.1090 kg b.100 kg c.10900 kg d.10 kg e.50 kg

Description : A dash pot consists of a cylinder 10 cm in diameter in which slides a piston 12 cm long having a radial clearance of 1 mm. The cylinder is filled with oil having a viscosity of 1 poise. What will be the resistance offered ... with a velocity of 3 cm/sec a.1090 kg b.100 kg c.10900 kg d.10 kg e.50 kg

Last Answer : c. 10900 kg

What is the speed of the piston in the cylinder of a petrol engine ?

Description : What is the speed of the piston in the cylinder of a petrol engine ?

Last Answer : The speed of the piston in the cylinder of a petrol engine is also the speed of the alternator.

City 100 Of Ring , piston, Timing Chain Change To do How much? Money Need it ?

Last Answer : How much ? Money It takes That Specified By To say Possible No. Of parts Quality And Displacement Different Price To be Can However Yours Talk According to All in all Approx Max 2,000 - 3,000 _ _ _ _ Money To take Can

Where to buy an electrically operated piston?

Description : Hello, where can I buy an electric piston?

Last Answer : Wouldn't you like to get a little divorced? Few people will understand what you're doing ...

buick 2005 lacross / how to compress rear calliper piston when changing brakes

Description : buick 2005 lacross / how to compress rear calliper piston when changing brakes

Last Answer : Need Answer

A liquid which is confined inside an adiabatic piston is suddently taken from state `-1` to state `-2` by a single stage irreversible process. If the

Description : A liquid which is confined inside an adiabatic piston is suddently taken from state `-1` to state `-2` by a single stage irreversible process. If the

Last Answer : A liquid which is confined inside an adiabatic piston is suddently taken from state `-1` to state `-2` by a single ... (0)` D. `DeltaU = -3P_(0)V_(0)`

The work done by a weightless piston in causing an expansing `Delta V` (at constant temperature), when the opposing pressure P is variable, is given b

Description : The work done by a weightless piston in causing an expansing `Delta V` (at constant temperature), when the opposing pressure P is variable, is given b

Last Answer : The work done by a weightless piston in causing an expansing `Delta V` (at constant temperature), when the opposing ... 0 C. `W = -P Delta V` D. None

A piston filled with `0.04` mole of an ideal gas expands reversible from `50.0mL` at a constant temperature of `37.0^(@)C` . As it does so, it absorbs

Description : A piston filled with `0.04` mole of an ideal gas expands reversible from `50.0mL` at a constant temperature of `37.0^(@)C` . As it does so, it absorbs

Last Answer : A piston filled with `0.04` mole of an ideal gas expands reversible from `50.0mL` at a constant temperature of `37. ... J` D. `q= +208 J, w=+208 J`

Show digramatically the changes in the position of piston, if a. Pressure is increased from 1.0 bar to 2.0 bar at constant temperature. 

Description : Show digramatically the changes in the position of piston, if a. Pressure is increased from 1.0 bar to 2.0 bar at constant temperature. 

Last Answer : Consider a sample of a gas in a cylinder with a movable piston. Show digramatically the changes in ... pressure is decreased from 4 bar to 3 bar.

Where might you find a cam actuated radial piston pump on a highway truck?

Description : Where might you find a cam actuated radial piston pump on a highway truck?

Last Answer : Fuel

If the output piston is a car hoist was replaced by a piston of twice the area what would happen to the output force?

Description : If the output piston is a car hoist was replaced by a piston of twice the area what would happen to the output force?

Last Answer : What is the answer ?

If a master cylinder with a two-square-inch piston travels 1/2 inch how far would the wheel cylinder with one -square-inch piston be moved?

Description : If a master cylinder with a two-square-inch piston travels 1/2 inch how far would the wheel cylinder with one -square-inch piston be moved?

Last Answer : -1

The domestic refrigerator uses following type of compressor (a) centrifugal (b) axial (c) miniature sealed unit (d) piston type reciprocating

Description : The domestic refrigerator uses following type of compressor (a) centrifugal (b) axial (c) miniature sealed unit (d) piston type reciprocating

Last Answer : Ans: d

In a naturally aspirated diesel engine, the air is supplied by a A. supercharger B. centrifugal pump C. movement of engine piston D. reciprocating pump

Description : In a naturally aspirated diesel engine, the air is supplied by a A. supercharger B. centrifugal pump C. movement of engine piston D. reciprocating pump

Last Answer : ANSWER : C

The energy of expanding gas is transferred by piston to connecting rod through a. Crank pin b. Gudgeon pin c. Bearing d. Crankcase (Ans:b)

Description : The energy of expanding gas is transferred by piston to connecting rod through a. Crank pin b. Gudgeon pin c. Bearing d. Crankcase (Ans:b)

Last Answer : Which of the following is not used in four stroke compression-ignition (CI) engines? a. Fuel pump b. Spark plug c. Fuel injector d. Inlet and outlet Valves (Ans:b)

Piston speed is equal to a. stroke x rpm b. (stroke x rpm) / 2 c. 2 x stroke x rpm d. 4 x stroke x rpm

Description : Piston speed is equal to a. stroke x rpm b. (stroke x rpm) / 2 c. 2 x stroke x rpm d. 4 x stroke x rpm

Last Answer : ANSWER c. 2 x stroke x rpm

Linear motion of the piston in a heat engine is converted into circular motion by

Description : Linear motion of the piston in a heat engine is converted into circular motion by

Last Answer : Crankshaft.

Forward movement of a piston in a steam engine is called

Description : Forward movement of a piston in a steam engine is called

Last Answer : expansion stroke.

In the expansion stroke of a petrol engine, the piston is pushed with a great stroke. Why?

Description : In the expansion stroke of a petrol engine, the piston is pushed with a great stroke. Why?

Last Answer : When the petrol-air mixture is ignited, carbon dioxide, carbon monoxide and water vapour expands suddenly. This exerts a great force on the piston.

Give reason: Steam exerts great pressure on the walls of the piston during expansion stroke.

Description : Give reason: Steam exerts great pressure on the walls of the piston during expansion stroke.

Last Answer : As steam occupies much larger volume than the same amount of water, it exerts great pressure on the walls of the piston.

The piston pin bearings in heavy-duty diesel engines are (a) needle roller bearings (b) tapered roller bearings (c) spherical roller bearings (d) cylindrical roller bearings

Description : The piston pin bearings in heavy-duty diesel engines are (a) needle roller bearings (b) tapered roller bearings (c) spherical roller bearings (d) cylindrical roller bearings

Last Answer : (a) needle roller bearings

Within the external combination engine, a piston rod is usually connected to the cross head by means of....... A. Cotter joints B. Universal joints C. Knuckle joint D. Bearing

Description : Within the external combination engine, a piston rod is usually connected to the cross head by means of....... A. Cotter joints B. Universal joints C. Knuckle joint D. Bearing

Last Answer : A. Cotter joints

In steam engine, the piston rod is usually connected to the cross head by means of a....... A. Cotter joints B. Universal joints C. Knuckle joint D. Bearing

Description : In steam engine, the piston rod is usually connected to the cross head by means of a....... A. Cotter joints B. Universal joints C. Knuckle joint D. Bearing

Last Answer : A. Cotter joints

The pressure inside a piston cylinder is a variable of a) Radius b) Plane angle c) Z plane distance d) Constant, not a variable

Description : The pressure inside a piston cylinder is a variable of a) Radius b) Plane angle c) Z plane distance d) Constant, not a variable

Last Answer : c) Z plane distance

For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston

Description : For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston

Last Answer : (A) Diffusion

For a reciprocating pump, the indicator diagram is the graph between the (A) Discharge and overall efficiency (B) Volume swept by piston for one complete revolution and the pressure in the cylinder (C) Angle swept by the crank pin at any instant and the discharge (D) None of these

Description : For a reciprocating pump, the indicator diagram is the graph between the (A) Discharge and overall efficiency (B) Volume swept by piston for one complete revolution and the pressure in the cylinder (C) Angle swept by the crank pin at any instant and the discharge (D) None of these

Last Answer : (B) Volume swept by piston for one complete revolution and the pressure in the cylinder

Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these

Description : Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these

Last Answer : (A) Turbine

A mono pump is a __________ pump. (A) Centrifugal (B) Piston (C) Positive acting rotary (D) A group of vacuum

Description : A mono pump is a __________ pump. (A) Centrifugal (B) Piston (C) Positive acting rotary (D) A group of vacuum

Last Answer : (C) Positive acting rotary

Medium viscosity lubricating oil can be most ideally pumped by a __________ pump. (A) Vane (B) Piston (C) Centrifugal (D) Plunger

Description : Medium viscosity lubricating oil can be most ideally pumped by a __________ pump. (A) Vane (B) Piston (C) Centrifugal (D) Plunger

Last Answer : (A) Vane

Pumping of a corrosive liquid is generally preferred to be done by a __________ pump, as it can be made of a variety of materials including plastics. (A) Piston (B) Gear (C) Positive displacement (D) Sump

Description : Pumping of a corrosive liquid is generally preferred to be done by a __________ pump, as it can be made of a variety of materials including plastics. (A) Piston (B) Gear (C) Positive displacement (D) Sump

Last Answer : (B) Gear

__________ pump is the most suitable device for discharging a liquid against a pressure of ≥ 1500 kgf/cm2 . (A) Centrifugal (B) Piston (C) Plunger (D) Vane

Description : __________ pump is the most suitable device for discharging a liquid against a pressure of ≥ 1500 kgf/cm2 . (A) Centrifugal (B) Piston (C) Plunger (D) Vane

Last Answer : (C) Plunger

6. Liquefaction of gases cannot be done by (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Merely compressing it beyond critical pressure (D) Adiabatic expansion against a piston or in a turbine

Description : 6. Liquefaction of gases cannot be done by (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Merely compressing it beyond critical pressure (D) Adiabatic expansion against a piston or in a turbine

Last Answer : (C) Merely compressing it beyond critical pressure

Claude process of gas liquefaction employs (A) Merely compression of gas beyond its critical pressure (B) Joule-Thomson expansion cooling (C) Heat exchange with colder stream (D) Adiabatic expansion against a piston or in a turbine

Description : Claude process of gas liquefaction employs (A) Merely compression of gas beyond its critical pressure (B) Joule-Thomson expansion cooling (C) Heat exchange with colder stream (D) Adiabatic expansion against a piston or in a turbine

Last Answer : (D) Adiabatic expansion against a piston or in a turbine

Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Description : Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Last Answer : (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion)

One mole of nitrogen at 8 bar and 600 K is contained in a piston cylinder arrangement. It is brought to 1 bar isothermally against a resisting pressure of 1 bar. The work done (in Joules) by the gas is (A) 30554 (B) 10373 (C) 4988.4 (D) 4364.9

Description : One mole of nitrogen at 8 bar and 600 K is contained in a piston cylinder arrangement. It is brought to 1 bar isothermally against a resisting pressure of 1 bar. The work done (in Joules) by the gas is (A) 30554 (B) 10373 (C) 4988.4 (D) 4364.9

Last Answer : (B) 10373

Consideration of the creep is the most important in case of the (A) Blades of gas turbine (B) Piston of an I. C. engine (C) Flywheel of steam engine (D) Cycle chain

Description : Consideration of the creep is the most important in case of the (A) Blades of gas turbine (B) Piston of an I. C. engine (C) Flywheel of steam engine (D) Cycle chain

Last Answer : (A) Blades of gas turbine

In tractor engine which of the following is a device in which liquid fuel is converted into gaseous fuel? 1. Piston 2. Carburetor 3. Both 1 and 2 4. none of these ans 1

Description : In tractor engine which of the following is a device in which liquid fuel is converted into gaseous fuel? 1. Piston 2. Carburetor 3. Both 1 and 2 4. none of these ans 1

Last Answer : ans 1

If piston displacement is deducted from the total volume of cylinder the remaining volume is known as 1. piston displacement 2. Clearance volume 3. displacement volume 4.compression ratio

Description : If piston displacement is deducted from the total volume of cylinder the remaining volume is known as 1. piston displacement 2. Clearance volume 3. displacement volume 4.compression ratio

Last Answer : ans 2

Piston displacement is the volume displaced by the piston during one stroke and is usually expressed in 1. Cubic meter 2.cubic inches 3. Both of these 4. none of these

Description : Piston displacement is the volume displaced by the piston during one stroke and is usually expressed in 1. Cubic meter 2.cubic inches 3. Both of these 4. none of these

Last Answer :    <!-- [endif] -->ans-1

he pump is used in power-operated sprayer is: A. Plunger type B. Diaphragm type C. Gear type D. Piston type

Description : The pump is used in power-operated sprayer is: A. Plunger type B. Diaphragm type C. Gear type D. Piston type

Last Answer : Gear type

Piston-cylinder arrangement of an internal combustion engine in automobile is called _________.  1. Rotary Joints  2. Prismatic Joints  3. Revolute Joints  4. Spherical Joints

Description : Piston-cylinder arrangement of an internal combustion engine in automobile is called _________.  1. Rotary Joints  2. Prismatic Joints  3. Revolute Joints  4. Spherical Joints

Last Answer : 2

Gas is enclosed in a cylinder with a weighted piston as the stop boundary. The gas is heated and expands from a volume of 0.04 m^3 to 0.10 m^3 at a constant pressure of 200kPa.Calculate the work done by the system.  A. 8 kJ  B. 10 kJ  C.12 kJ  D.14 kJ Formula: W = p(V2-V1)

Description : Gas is enclosed in a cylinder with a weighted piston as the stop boundary. The gas is heated and expands from a volume of 0.04 m^3 to 0.10 m^3 at a constant pressure of 200kPa.Calculate the work done by the system.  A. 8 kJ  B. 10 kJ  C.12 kJ  D.14 kJ Formula: W = p(V2-V1)

Last Answer : 12 kJ

A gas is enclosed in a cylinder with a weighted piston as the top boundary. The gas is heated and expands from a volume of 0.04 m3 to 0.10 m3 at a constant pressure of 200 kPa. Find the work done on the system.  a. 5 kJ  b. 15 kJ  c. 10 kJ  d. 12 kJ

Description : A gas is enclosed in a cylinder with a weighted piston as the top boundary. The gas is heated and expands from a volume of 0.04 m3 to 0.10 m3 at a constant pressure of 200 kPa. Find the work done on the system.  a. 5 kJ  b. 15 kJ  c. 10 kJ  d. 12 kJ

Last Answer : 12 kJ

A gas is compressed in a cylinder by a movable piston to a volume onehalf its original volume. During the process 300 kJ heat left the gas and internal energy remained same. The work done on gas in Nm will be  (a) 300 Nm  (b) 300,000 Nm  (c) 30 Nm  (d) 3000 Nm  (e) 30,000 Nm.

Description : A gas is compressed in a cylinder by a movable piston to a volume onehalf its original volume. During the process 300 kJ heat left the gas and internal energy remained same. The work done on gas in Nm will be  (a) 300 Nm  (b) 300,000 Nm  (c) 30 Nm  (d) 3000 Nm  (e) 30,000 Nm.

Last Answer : Answer : b

What is a balance piston?

Description : What is a balance piston?

Last Answer : Reaction turbines have axial thrust because pressure on the entering side is greater than pressure on the leaving side of each stage. To counteract this force, steam is admitted to a dummy (balance) ... thrust. Instead of piston, seal strips are also used to duplicate a piston's counter force.

The EGT indication on a piston engine is used

Description : The EGT indication on a piston engine is used

Last Answer : C. To assist the pilot to adjust the fuel mixture