Description : Operating pressure of power operated sprayer E. 1-7 kg/cm2 F. 10-20 kg/cm2+ G. 20-55 kg/cm2 H. >55 kg/cm2
Last Answer : G. 20-55 kg/cm2
Description : Operating pressure of the hand operated sprayer is E. 20-55 kg/cm2 F. 1-7 kg/cm2 G. 10-20 kg/cm2 H. >55 kg/cm2
Last Answer : F. 1-7 kg/cm2
Description : Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions
Last Answer : f. Dried hard soils
Description : Worm gear are used for transmitting power between two Shaft Inclined at e. At right angle to each other and axes can intersect f. At right angle to each other but axis cannot intersect each other g. At right angle to each other and in different planes h. None of the above
Last Answer : f. At right angle to each other but axis cannot intersect each other
Description : The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above
Last Answer : E. Automatic draft control system
Description : Juice extraction capacity of vertical three roller type bullock down sugercane crusher E. 50-70% F. 70-90% G. 90-100% H. 30-50%
Last Answer : E. 50-70%
Description : Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above
Last Answer : F. Capacity of chaff cutters
Description : Speed of power operated machine chaff cutter is E. 35 rpm F. 50 rpm G. 600-1000 rpm H. None of the above
Last Answer : G. 600-1000 rpm
Description : Speed of band operated machines chaff cutter having two knives F. 35 rpm G. 50 rpm H. 600 rpm I. 1000 rpm
Last Answer : F. 35 rpm
Description : Which of the following ranges identifies the amount of pressure within the endotracheal tube cuff that is believed to prevent both injury and aspiration? a) 20-25 mm Hg water pressure. Usually the ... pressure A measure of 0-5 mm Hg water pressure would indicate that the cuff is underinflated.
Last Answer : a) 20-25 mm Hg water pressure. Usually the pressure is maintained at less than 25 cm water pressure to prevent injury and at more than 20 cm water pressure to prevent aspiration.
Description : Opening WDV off the block of assets was Rs 15 lakh. During the year, asset was acquired under this block on 15 June 2017 amounting to rupees 10 lakh. One of the assets falling within the block was sold for rupees 5.5 ... . rupees 1.95 lakh f. rupees 2.5 lakh g. rupees 2.25 lakh h. Rs 1.45 lakh
Last Answer : e. rupees 1.95 lakh
Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.
Last Answer : 1200 to 1500
Description : Weight per unit of drawbar power is generally ranges between a)50-120kg/kw b)120-150kg/kw c)150-250kg/kw d)250-300kg/kw
Last Answer : a)50-120kg/kw
Description : The spacing between the discs in the gang bolt ranges cm for lighy duty and cm heavy -duty harrows i. 15-25 and 25-30 c) 40-45 and 45-50 ii. 20-30 and 30-40. d) 15-25 and 32-36
Last Answer : 15-25 and 25-30
Description : The purpose of registration in a mower is (A) to get uniform length of cut of grass (B)to run the mower at minimum power (C)to run the mower at uniform torque (D)to reduce the occurrence of overload
Last Answer : (B)to run the mower at minimum power
Description : 345- Excessive stalk deflection particularly when cutting close to ground results in ...... (a) Stubbles of uneven length (b) Increased tedency of stalk to cut by cutting unit..... (c) Less unevenness in cutting (d) Less missing or uncut stalk
Last Answer : (a) Stubbles of uneven length
Description : Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec
Last Answer : B. 18-20m/sec
Description : The required spacing between the disc on the gang bolt ranges from 15 to 25 cm for light duty and 25 to 30cm for heavy duty harrows is b. 25 to 35cm c. 25 to 40cm d. None of the above.
Last Answer : <!-- [endif] -->Ans - a. 25 to 30cm
Description : Air output of a duster is given by formula a) Q= 60×A×V b)Q= 60×A×(2GH/Y) c) Q= 240×A×h d) all of the above
Last Answer : d) all of the above
Description : 2m combine is operating at 4 kmph with an overall efficiency of 75%. The area covered by in(ha\h) will be: a. 0.4 b. 0.6 c. 0.8 d. 1.0
Last Answer : b. 0.6
Description : power spray are operated at a pressure. a. 5-10 kg/m2 b.10-20 kg/m2 c.20-55 kg/m2 d.>55 kg/m2
Last Answer : c.20-55 kg/m2
Description : .The number of knives on powered chaff cutter a) 2-6 b) 1-2 c) 5-10 d) 10-20
Last Answer : a) 2-6
Description : Two columns 50 cm 50 cm and 60 cm 60 cm carry 80 tonnes and 120 tonnes of loads respectively. The centre to centre distance between columns is 5.00 metres. The permissible bearing capacity of the soil is 20 t ... the foundation slab = 7.00 m (C) Area of footing slab = 11.00 m2 (D) All the above
Last Answer : Option D
Description : Size of MB plow is determined by (a) depth of cut (b) width of cut (c) number of accessories (d) none of the above
Last Answer : (b) width of cut
Description : Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle
Last Answer : a)Increasing disc angle
Description : the mowers are designed to cut: a) Wheat b) Paddy c) Mustard d) Grasses
Last Answer : d) Grasses
Description : Disc angle adjustment influences: a. Depth of cut b. width of cut c. Soil break up d. Direction of travel
Last Answer : b. width of cut
Description : Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut
Last Answer : b. Depth of cut
Description : Cut-off device is not required with (a) Inclined plate metering (b) Horizontally plate metering (c) Vertically plate metering (d) All of the above
Last Answer : (a) Inclined plate metering
Description : Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism
Last Answer : (d) Inclined plate metering mechanism
Description : Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%
Last Answer : A. 10-20%
Description : Total mechanical losses ( frictional losses , pumping loss in intake and exhaust and power accessories) will amount to a.10-20 % ihp b.2-10 % ihp c.20-30 % ihp d.30 -50 % ihp
Last Answer : a.10-20 % ihp
Description : Hand operated sprayer are operated at a pressure (kg/cm2) a) 1-7 b) 7-10 c)10-20 d) 20-55
Last Answer : a) 1-7
Description : Application rates for dusters are a.40 kg/ha
Last Answer : a.
Description : Agitator(propeller or paddle)type for agitating liquid in power sprays have a velocity of a.100-120 rpm b.60-100 rpm c.10-20 rpm d. none of the above
Last Answer : a.100-120 rpm
Description : Compression pressure in petrol engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) 35-40 kg/cm2
Last Answer : a) 6-10 kg/cm2
Description : Compression pressure in diesel engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) None of the above
Last Answer : c) 20-35 kg/cm2
Description : Cutting speed of the impact type cutter is a)10-20 m/s. b)20-40m/s c)40-50m/s. d)46-56m/s
Last Answer : b)20-40m/s
Description : Which of the following pair is incorrect: a) Cut - CTRL + X b) Copy - CTRL + C c) Paste - CTRL + V d) Select All - CTRL + A e) Find - CTRL + F f) Undo -CTRL + Z g) None of These h) All of Above
Last Answer : g) None of These
Description : operation is used to cut and mix the soil e) rotary f) mlutch g) strip h) none of these
Last Answer : rotary
Description : High carbon steel having carbon content about (A) 0.25 % (B) 0.25 – 0.50 % (C) 0.50 – 1.5 % (D) 2.5 - 4.5 %
Last Answer : (C) 0.50 – 1.5 %
Description : Medium Carbon steel was carbon content about (A) 0.25 % (B) 0.25 – 0.50 % (C) 0.50 – 1.5 % (D) 2.5 – 4.5 %
Last Answer : (B) 0.25 – 0.50 %
Description : Carbon content in the cast iron is (A) 2.5 – 4.5 % (B) 0 – 0.25 % (C) 0.25 – 0.50 % (D) 0.50 – 1.5 %
Last Answer : (B) 0 – 0.25 %
Description : Stroke bore ratio for tractor engine is (a) 1.25 (b) 1.45 (c) 1.75 (d) 2.00
Last Answer : (a) 1.25
Description : Improved uniformity is obtained if seed tube is inclined rear ward at _________ with vertical. a)5-15° b)15-30° c)30-40° d)40-50
Last Answer : b)15-30°
Description : Length of open belt is given by formula a. L=[2C+( 2) (DI+D2)] + [ /4C] b. L=[2C+( 2) (DI+D2)] + [ /4C] c. L=[2C+( 2) (DI+D2)] + [ ] d. L=[2C+( 2) (DI D2)] + [ ]
Last Answer : a. L=[2C+( 2) (DI+D2)] + [ /4C]
Description : .Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely
Last Answer : c) No affect
Description : The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow
Last Answer : D. The number of furrow openers x distance between two furrow
Description : pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement
Last Answer : c) Both (a) and (b)
Description : Dynamic similarity between the model and prototype signifies similarities of a) Motion b) Force c) Length d) None of the above
Last Answer : b) Force