The top diameter, bottom diameter and height of the mould used for slump test are (a) 100mm, 200mm, 300mm (b) 200mm,100mm,300mm (c) 200mm,300mm,100mm (d) 100mm,300mm,200mm

The top diameter, bottom diameter and height of the mould used for slump test are
(a) 100mm, 200mm, 300mm
(b) 200mm,100mm,300mm
(c) 200mm,300mm,100mm
(d) 100mm,300mm,200mm
by

1 Answer

Answer :

(a) 100mm, 200mm, 300mm
by

Related questions

The top diameter, bottom diameter and the height of a slump mould are: (A) 10 cm, 20 cm, 30 cm (B) 10 cm, 30 cm, 20 cm (C) 20 cm, 10 cm, 30 cm (D) 20 cm, 30 cm, 10 cm

Description : The top diameter, bottom diameter and the height of a slump mould are: (A) 10 cm, 20 cm, 30 cm (B) 10 cm, 30 cm, 20 cm (C) 20 cm, 10 cm, 30 cm (D) 20 cm, 30 cm, 10 cm

Last Answer : (A) 10 cm, 20 cm, 30 cm

Pick up the incorrect statement from the following: (A) The bottom and top ends of slump mould are parallel to each other (B) The axis of the mould is perpendicular to the end faces (C) The internal surface of the mould is kept clean and free from set cement (D) The mould is in the form of a frustum of hexagonal pyramid

Description : Pick up the incorrect statement from the following: (A) The bottom and top ends of slump mould are parallel to each other (B) The axis of the mould is perpendicular to the end faces (C) The ... clean and free from set cement (D) The mould is in the form of a frustum of hexagonal pyramid

Last Answer : Answer: Option D

The height of a toe board must be at least? a. 100mm (4 inches) b. 200mm (8 inches) c. 150mm (6 inches) d. 230mm (9 inches)

Description : The height of a toe board must be at least? a. 100mm (4 inches) b. 200mm (8 inches) c. 150mm (6 inches) d. 230mm (9 inches)

Last Answer : c. 150mm (6 inches)

What is the height of the base lift (kicker lift) on a typical tube and coupler scaffold? a. 225mm (9 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 100mm (4 inches)

Description : What is the height of the base lift (kicker lift) on a typical tube and coupler scaffold? a. 225mm (9 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 100mm (4 inches)

Last Answer : c. 150mm (6 inches

Nikon 55-200mm vs Nikon 70-300mm. Would you pick the former, or the latter?

Description : Nikon 55-200mm vs Nikon 70-300mm. Would you pick the former, or the latter?

Last Answer : i’d go for the 55–200 but i was never a big fan of telephoto. still, i think the versatility and price clinch it.

A guardrail system must be fitted if the distance between a working platform a wall is more than? a. 100mm (4 inches) b. 360mm (14 inches) c. 200mm (8 inches) d. 460mm (18 inches)

Description : A guardrail system must be fitted if the distance between a working platform a wall is more than? a. 100mm (4 inches) b. 360mm (14 inches) c. 200mm (8 inches) d. 460mm (18 inches)

Last Answer : b. 360mm (14 inches)

What is the maximum distance that bracing can be installed from a node point on a scaffold? a. 200mm (8 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 250mm (10 inches)

Description : What is the maximum distance that bracing can be installed from a node point on a scaffold? a. 200mm (8 inches) b. 300mm (12 inches) c. 150mm (6 inches) d. 250mm (10 inches)

Last Answer : b. 300mm (12 inches)

For high degree of workability, the slump value should vary between (a) 0 to 25mm (b) 25 to 50mm (c) 50 to 80mm (d) 80 to 100mm

Description : For high degree of workability, the slump value should vary between (a) 0 to 25mm (b) 25 to 50mm (c) 50 to 80mm (d) 80 to 100mm

Last Answer : (d) 80 to 100mm

The steel mould used for slump test is in the form of a (a) Cube (b) Cylinder (c) Frustrum of a cone (d) None of these

Description : The steel mould used for slump test is in the form of a (a) Cube (b) Cylinder (c) Frustrum of a cone (d) None of these

Last Answer : (c) Frustrum of a cone

In slump test, each layer of concrete is compacted by a steel rod 60 cm long and of 16 mm diameter for (A) 20 times (B) 25 times (C) 30 times (D) 50 time

Description : In slump test, each layer of concrete is compacted by a steel rod 60 cm long and of 16 mm diameter for (A) 20 times (B) 25 times (C) 30 times (D) 50 time

Last Answer : Answer: Option B

The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio is 18, then the stress developed in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Last Answer : (b) 135N/mm2

A relative short and broad mould board is curved rather abruptly near the top resulting in a greater degree of pulverization is called a. Sod bottom b. Stubble bottom b. General bottom d. Slat bottom

Description : A relative short and broad mould board is curved rather abruptly near the top resulting in a greater degree of pulverization is called a. Sod bottom b. Stubble bottom b. General bottom d. Slat bottom

Last Answer : b. General bottom

he frame has a base diameter of 20 cm and height of 30 cm. A margin of 2.5 cm is to be given for folding it over the top and bottom of the frame. -Maths 9th

Description : he frame has a base diameter of 20 cm and height of 30 cm. A margin of 2.5 cm is to be given for folding it over the top and bottom of the frame. -Maths 9th

Last Answer : Say h = height of the frame of lampshade, looks like cylindrical shape r = radius Total height is h = (2.5+30+2.5) cm = 35cm and r = (20/2) cm = 10cm Use curved surface area formula to find the ... 2πrh = (2 (22/7) 10 35) cm2 = 2200 cm2 Hence, 2200 cm2 cloth is required for covering the lampshade.

Height of crucible is kept from top surface of mould? (i) 30 mm (ii) 40 mm (iii) 50 mm* (iv) 60 mm

Description : Height of crucible is kept from top surface of mould? (i) 30 mm (ii) 40 mm (iii) 50 mm* (iv) 60 mm

Last Answer : (iii) 50 mm*

If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Last Answer : b) 140mm

If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Last Answer : a) 100mm

If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm

Last Answer : b) 140mm

If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm

Last Answer : a) 100mm

A cantilever shaft having 50 mm diameter and a length of 300mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Determine the static deflection of shaft in mm. A 0.144 B 0.244 C 0.344 D 0.444

Description : A cantilever shaft having 50 mm diameter and a length of 300mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Determine the static deflection of shaft in mm. A 0.144 B 0.244 C 0.344 D 0.444

Last Answer : A 0.144

A 300mm diameter pipe, 5mm wall thickness is to be radiographed using the double wall single image technique. The source to be used is Iridium. Which of the following statements is true? a) It should not be done because the thickness is below that recommended b) It should be better to use a cobalt 60 source in this instance c) There is no problem with the technique d) Only the double wall, double image technique should be used with Iridium

Description : A 300mm diameter pipe, 5mm wall thickness is to be radiographed using the double wall single image technique. The source to be used is Iridium. Which of the following statements is true? a) ... problem with the technique d) Only the double wall, double image technique should be used with Iridium

Last Answer : c) There is no problem with the technique

What is maximum height above rail level for low-level passenger platform for BG? (a) 300mm (b) 455mm* (c) 525mm (d) 550mm

Description : What is maximum height above rail level for low-level passenger platform for BG? (a) 300mm (b) 455mm* (c) 525mm (d) 550mm

Last Answer : (b) 455mm

In case of Raymond pile (A) Lengths vary from 6 m to 12 m (B) Diameter of top of piles varies from 40 cm to 60 cm (C) Diameter of pile at bottom varies from 20 cm to 28 cm (D) All the above

Description : In case of Raymond pile (A) Lengths vary from 6 m to 12 m (B) Diameter of top of piles varies from 40 cm to 60 cm (C) Diameter of pile at bottom varies from 20 cm to 28 cm (D) All the above

Last Answer : Answer: Option D

If on­site slump test fails, should engineers allow the contractor to continue the concreting works?

Description : If on­site slump test fails, should engineers allow the contractor to continue the concreting works?

Last Answer : This is a very classical question raised by many graduate engineers. In fact, there are two schools of thought regarding this issue. The first school of thought is rather straightforward: the contractor ... t the Engineer exercise his power to stop the contractor and save these extra time and cost?

Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Last Answer : (A) Consistency

Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Last Answer : (A) Consistency

Slump test is done for (A) Clay (B) Sand (C) Lime (D) Concrete

Description : Slump test is done for (A) Clay (B) Sand (C) Lime (D) Concrete

Last Answer : Answer: Option D

Workability of concrete is measured by (A) Vicat apparatus test (B) Slump test (C) Minimum void method (D) Talbot Richa

Description : Workability of concrete is measured by (A) Vicat apparatus test (B) Slump test (C) Minimum void method (D) Talbot Richa

Last Answer : Answer: Option B

Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Last Answer : Answer: Option C

Slump test for concrete is carried out, to determine (A) Strength (B) Durability (C) Workability (D) Water content

Description : Slump test for concrete is carried out, to determine (A) Strength (B) Durability (C) Workability (D) Water content

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C) Curing of concrete is done for proper compaction of cement (D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Description : Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C ... D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Last Answer : Option D

The slump test of concrete is used to measure its (a) Consistency (b) Mobility (c) Homogeneity (d) All the above

Description : The slump test of concrete is used to measure its (a) Consistency (b) Mobility (c) Homogeneity (d) All the above

Last Answer : (a) Consistency

Workability of a concrete – mix is determined by (i)Slump cone test (ii)Compaction factor test (iii)Vee bee test [ A ] i [ B ] ii [ C ] i and ii [ D ] i, ii and iii

Description : Workability of a concrete – mix is determined by (i)Slump cone test (ii)Compaction factor test (iii)Vee bee test [ A ] i [ B ] ii [ C ] i and ii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value

Description : Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value

Last Answer : [ A ] Consistency

Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test

Last Answer : [ C ] Compaction factor test

While determining the workability of concrete mix, the compaction factor test is ------than the slump cone test [ A ] Less accurate [ B ] More accurate [ C ] Approximate method [ D ] None of the above

Description : While determining the workability of concrete mix, the compaction factor test is ------than the slump cone test [ A ] Less accurate [ B ] More accurate [ C ] Approximate method [ D ] None of the above

Last Answer : [ B ] More accurate

Slump cone test is used to determine [ A ] Shrinkage of concrete mix [ B ] Creep of concrete [ C ] Workability of concrete mix [ D ] Soundness of concrete

Description : Slump cone test is used to determine [ A ] Shrinkage of concrete mix [ B ] Creep of concrete [ C ] Workability of concrete mix [ D ] Soundness of concrete

Last Answer : [ C ] Workability of concrete mix

The discharge through a large rectangular orifice is given by (where H1 = Height of the liquid above the top of the orifice, H2 = Height of the liquid above the bottom of the orifice, b = Breadth of the orifice, and Cd = Coefficient of discharge) (A) Q = (2/3) Cd × b × (2g) × (H2 - H1) (B) Q = (2/3) Cd × b × (2g) × (H2 1/2 - H1 1/2) (C) Q = (2/3) Cd × b × (2g) × (H2 3/2 - H1 3/2) (D) Q = (2/3) Cd × b × (2g) × (H2 2 - H1 2 )

Description : The discharge through a large rectangular orifice is given by (where H1 = Height of the liquid above the top of the orifice, H2 = Height of the liquid above the bottom of the orifice, b = Breadth of the orifice, and Cd = Coefficient of ... H1 3/2) (D) Q = (2/3) Cd b (2g) (H2 2 - H1 2 )

Last Answer : Answer: Option C

In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv

Description : In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv

Last Answer : [ A ] i and iii

The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)

Description : The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)

Last Answer : [ C ] Smaller of (a) and (b)

.Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely

Description : .Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely

Last Answer : c) No affect

A low mold board with gradual twist that completely invert the furrow slice with a minimum of breakup, thus covering vegetative matter thoroughly is called a. Stubble bottom b. sod bottom c. salted mould board d. general purpose bottom

Description : A low mold board with gradual twist that completely invert the furrow slice with a minimum of breakup, thus covering vegetative matter thoroughly is called a. Stubble bottom b. sod bottom c. salted mould board d. general purpose bottom

Last Answer : b. sod bottom

A long jow mould board with a gradual twist (spiral) that completely inverts the furrow slice with a minimum of break up thus covering vegetative matter thoroughly is called a. Sod bottom b. Stubble bottom c. General bottom d. Slat bottom

Description : A long jow mould board with a gradual twist (spiral) that completely inverts the furrow slice with a minimum of break up thus covering vegetative matter thoroughly is called a. Sod bottom b. Stubble bottom c. General bottom d. Slat bottom

Last Answer : a. Sod bottom

…………………………... moves the trash and roots from ahead of shin towords the main furrow so as 10 ensure complete coverage by the plough bottom a. Coulter b. Jointer c. Mould board d. Shin

Description : …………………………... moves the trash and roots from ahead of shin towords the main furrow so as 10 ensure complete coverage by the plough bottom a. Coulter b. Jointer c. Mould board d. Shin

Last Answer : b. Jointer

A mould board plough bottom acts as a a. Single sided wedge b. Double sided wedge c. Three sided wedge d. All of the above

Description : A mould board plough bottom acts as a a. Single sided wedge b. Double sided wedge c. Three sided wedge d. All of the above

Last Answer : c. Three sided wedg

Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the rate of (P/4) + 3.0 percentage of water where P is the percentage of water for standard consistency (C) A cube mould of 10 cm × 10 cm × 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Description : Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the ... cm 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Last Answer : Answer: Option A

For performing the compressive strength test of cement, the size of cube mould should be (a) 7.06cm (b)75mm (c)80mm (d)All the above

Description : For performing the compressive strength test of cement, the size of cube mould should be (a) 7.06cm (b)75mm (c)80mm (d)All the above

Last Answer : (a) 7.06cm

Pick out the correct statement.(A) Angle of repose is always greater than the angle of slide (B) A hopper is a small bin with a sloping bottom (C) A silo is a short height vessel of very large diameter used for the storage of high volatile matter coal (D) Pine oil is used as a 'modifying agent' (for activating or depressing the adsorption of filming agents) in froth floatation process

Description : Pick out the correct statement. (A) Angle of repose is always greater than the angle of slide (B) A hopper is a small bin with a sloping bottom (C) A silo is a short height ... used as a 'modifying agent' (for activating or depressing the adsorption of filming agents) in froth floatation process

Last Answer : (B) A hopper is a small bin with a sloping bottom

Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The clearance between the tank bottom and the bottom most impeller should be about (where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Description : Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The ... where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Last Answer : (B) D

Tamron 18-270mm vs Canon 18-200mm vs Canon 18-135mm vs Canon 18-55mm+Canon 55-250mm --Which should I get?

Description : Tamron 18-270mm vs Canon 18-200mm vs Canon 18-135mm vs Canon 18-55mm+Canon 55-250mm --Which should I get?

Last Answer : answer:270 needs more light. As does the 250. IE Slower shutter speed and/or larger aperture.

has amplitude of vibration is 200mm and frequency of operation is 400 cycle/ sec. b. Acme tooth harrow c. Blade harrow d. None of the above

Description : has amplitude of vibration is 200mm and frequency of operation is 400 cycle/ sec. b. Acme tooth harrow c. Blade harrow d. None of the above

Last Answer : Ans- a. Reciprocating power harrow