Description : he temperature at which solid content of fuel freeze out is called.... (a) Fire point (b) Flash point (c) Pour point (d) Cloud point
Last Answer : (a) Fire point
Description : The temperature at which flame persists for approximately five seconds is called..... (a) Fire point (b) Flash point (c) Pour point (d) cloud point
Description : Which temperature for a lubricating oil will be lowest ? (A) Flash point (B) Fire point (C) Pour point (D) Boiling
Last Answer : Ans: C
Description : Which of the following is the most important property for a jet fuel? (A) Cloud point (B) Pour point (C) Colour (D) Freezing point
Last Answer : (D) Freezing point
Description : Pick out the wrong statement. (A) LPG is also used as fuel for automobiles & small furnaces and for cutting & welding of metals (B) The minimum temperature, at which a petroleum oil vapor catches ... about 30-50 Nm3 of gas (D) Maximum yield of naphthalene is obtained on distillation of crude oil
Last Answer : (B) The minimum temperature, at which a petroleum oil vapor catches fire and continues to burn, is called its flash point
Description : In case of liquid petrofuels, momentary combustion is observed at its (A) Flash point (B) Preheating temperature corresponding to viscosity of 25 centistokes (C) Flame temperature (D) Fire point
Last Answer : (A) Flash point
Description : Presence of predominantly large quantity of aromatics (polynuclear) is not desirable in aviation fuel, because it has (A) High pour point and low smoke point (B) Low viscosity index (C) High self-ignition temperature (D) All (A), (B) and (C)
Last Answer : (B) Low viscosity index
Description : ears commonly used on fuel injection pumps are a. Spur gears b. helical gears c. rack and pinion d. spiral gears
Last Answer : c. rack and pinion
Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above
Last Answer : ∙ Torque is a function of thermal efficiency
Description : Injection pressure of fuel nozzle in diesel engine is a) 30-45 kg/cm2 b) 50-100 kg/cm2 c) 120-200 kg/cm2 d) 200 kg/cm2
Last Answer : c) 120-200 kg/cm2
Description : gnition delay is defined as the A)time between start of fuel injection and ignition of fuel B)time between end of fuel injection and ignition of fuel C)time between start of ignition and tdc D)time between completion of ignition and bdc
Last Answer : A)time between start of fuel injection and ignition of fuel
Description : Tension on slack side in case of chain drive a) Lesser than on tight side b) Greater than on tight side c) Zero d) Equal to that on tight side
Last Answer : c) Zero
Description : Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm
Last Answer : a)400-550 rpm
Description : Reid vapour pressure of gasoline is the measure of its (A) Pour point (B) Cloud point (C) Vapour locking tendency (D) Carbon residue
Last Answer : (C) Vapour locking tendency
Description : Define following: i) Oiliness ii) Volatility iii) Cloud point iv)Pour point
Last Answer : i) Oiliness: -It is defined as the power of an oil to maintain a continuous film under pressure while used a lubricant. ii) Volatility: - Volatility of oil is its tendency to vaporize with the ... iv) Pour point: It is defined as the temperature at which oil ceases to flow or pour on cooling
Description : Explain the following properties i) Pour point ii) Viscosity iii) Ignition quality iv) Fire point
Last Answer : i. Pour point: Pour point is the temperature below which the entire mass of fuel, solid or liquid together, freeze and thus cause flow of fuel impossible. Pour point is usually 5 to 10 °C below ... is the temperature at which the flash will sustain itself as a steady flame for at least five seconds.
Description : Fuel oil is subjected to visbreaking to reduce its (A) Pour point (B) Viscosity (C) Pressure drop on pumping (D) All (A), (B) and (C
Last Answer : (D) All (A), (B) and (C
Description : The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above
Last Answer : E. Automatic draft control system
Description : Volumetric efficiency is affected by (A) Turbulence velocity and temperature of intake manifold (B) Efficiency of exhaust stroke (C) Valve timing overlap (D) All the above
Last Answer : (D) All the above
Description : 40 optimum working temperature for diesel engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c
Last Answer : ∙ 88-90°c
Description : ptimum working temperature for petrol engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c
Last Answer : ∙ 71-82°c
Description : The ideal moisture content for the soil primary tillage operation a) Upper plastic limit of the soil b) Lower plastic limit c) Wilting Point d) All of the above
Last Answer : a) Upper plastic limit of the soil
Description : The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links
Last Answer : d) Between two lower links
Last Answer : Kerosene Of water Than Light Says.
Description : The lowest temperature, at which a solid fuel produces enough vapors to support continuous combustion, is called (A) Fire point (B) Smoke point (C) Burning temperature (D) Kindling temperature
Last Answer : (C) Burning temperature
Description : Pour point of a petrofuel is (A) Multiple of 3°F (B) Multiple of 5°F (C) 5°C below the temperature at which oil ceases to flow (D) None of these
Last Answer : (C) 5°C below the temperature at which oil ceases to flow
Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above
Last Answer : B. L-head
Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above
Last Answer : d) None of the above
Description : Dead furrow open furrow is called when plowing is done by (a) Center to side (b) side to center method (c) one way plowing (d) none of the above
Last Answer : (b) side to center method
Description : Total force exerted upon the implement by a power unit called a)pull. B) draft C)side draft. D)unit draft
Last Answer : a)pull
Description : Horizontal component of pull perpendicular to the line of motion is called: A.Draft B.Side draft C.Transerve component D. Pull
Last Answer : B.Side draft
Description : A low mold board with gradual twist that completely invert the furrow slice with a minimum of breakup, thus covering vegetative matter thoroughly is called a. Stubble bottom b. sod bottom c. salted mould board d. general purpose bottom
Last Answer : b. sod bottom
Description : Equipment for placing seeding in the soil called: a) Seed drill b) Seed cum fertilizer drill c) Planter d) Transplanter
Last Answer : d) Transplanter
Description : Rotavator working in reverse direction for compacting soil and giving good touch to inter culturing is called a) Rotary tiller b) Power tiller c) Power harrow d) Treader
Last Answer : d) Treader
Description : A relative short and broad mould board is curved rather abruptly near the top resulting in a greater degree of pulverization is called a. Sod bottom b. Stubble bottom b. General bottom d. Slat bottom
Last Answer : b. General bottom
Description : A long jow mould board with a gradual twist (spiral) that completely inverts the furrow slice with a minimum of break up thus covering vegetative matter thoroughly is called a. Sod bottom b. Stubble bottom c. General bottom d. Slat bottom
Last Answer : a. Sod bottom
Description : The force that holds two particles of the different kind together is called as a) Adhesion c) Shear force b) Cohesion d) Compressive
Last Answer : a) Adhesion
Description : The force that holds two particles of the same kind together is called as a) Adhesion c) shear force b) cohesion d) compressive
Last Answer : b) cohesion
Description : Force ( including rolling resistance friction ) that acts upon the stabilising surfaces such landslide and sole of bottom are called a) Useful soil resistance b) Parasitic force d) Draft of implement. d) Pull of implement
Last Answer : b) Parasitic force
Description : Forces which a tool must overcome in cutting, breaking and moving the soil is called a) Useful soil resistance b) Parasitic force c) Draft of implement d) Pull of implement
Last Answer : a) Useful soil resistance
Description : 349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss
Last Answer : (d) Gathering loss
Description : The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index
Last Answer : (c)reel speed index
Description : Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss
Last Answer : (b) Shoe loss
Description : Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss
Last Answer : (b) walker loss(rack loss)
Description : Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss
Last Answer : (a)cylinder loss
Description : Higher viscosity of lubricating oil usually signifies (A) Lower Reid vapour pressure (B) Higher acid number (C) Higher flash point and fire point (D) Lower flash point and fire point
Last Answer : (C) Higher flash point and fire point
Description : verticalsuctioninmouldboardploughis______whereashorizontalsuctionis______
Last Answer : .0.3to0.5cm,0.5cm
Description : Byincreasingdiskangle,depthpenetration_____beoverwithofcut_______
Last Answer : .decreases,increases
Description : A paddy transplanter uses either root wash type seedlings or __________ seedlings.
Last Answer : soil bearing
Description : An indigenous plough cuts a _________furrow cross sect
Last Answer : Trapizoidal