Description : The temperature at which fuel flows to case is called.... (a) Fire point (b) Flash point (c) Pour point (d) Cloud point
Last Answer : c) Pour point
Description : The temperature at which flame persists for approximately five seconds is called..... (a) Fire point (b) Flash point (c) Pour point (d) cloud point
Last Answer : (a) Fire point
Description : Which temperature for a lubricating oil will be lowest ? (A) Flash point (B) Fire point (C) Pour point (D) Boiling
Last Answer : Ans: C
Description : Which of the following is the most important property for a jet fuel? (A) Cloud point (B) Pour point (C) Colour (D) Freezing point
Last Answer : (D) Freezing point
Description : Pick out the wrong statement. (A) LPG is also used as fuel for automobiles & small furnaces and for cutting & welding of metals (B) The minimum temperature, at which a petroleum oil vapor catches ... about 30-50 Nm3 of gas (D) Maximum yield of naphthalene is obtained on distillation of crude oil
Last Answer : (B) The minimum temperature, at which a petroleum oil vapor catches fire and continues to burn, is called its flash point
Description : The ideal moisture content for the soil primary tillage operation a) Upper plastic limit of the soil b) Lower plastic limit c) Wilting Point d) All of the above
Last Answer : a) Upper plastic limit of the soil
Description : The lowest temperature, at which a solid fuel produces enough vapors to support continuous combustion, is called (A) Fire point (B) Smoke point (C) Burning temperature (D) Kindling temperature
Last Answer : (C) Burning temperature
Description : Presence of predominantly large quantity of aromatics (polynuclear) is not desirable in aviation fuel, because it has (A) High pour point and low smoke point (B) Low viscosity index (C) High self-ignition temperature (D) All (A), (B) and (C)
Last Answer : (B) Low viscosity index
Description : The nozzle used for chemical spraying of weedicides (a) hollow cone nozzle (b) solid cone nozzle (c) flat fan nozzle (d) flooding nozzle
Last Answer : (c) flat fan nozzle
Description : A slat mould board scours better than a solid mould board because of smaller contact area resulting in a) Reduction of adhesive force b) Increase in soil pressure c) Both (a) and (b) d) None of the above
Last Answer : c) Both (a) and (b)
Description : ears commonly used on fuel injection pumps are a. Spur gears b. helical gears c. rack and pinion d. spiral gears
Last Answer : c. rack and pinion
Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above
Last Answer : ∙ Torque is a function of thermal efficiency
Description : Injection pressure of fuel nozzle in diesel engine is a) 30-45 kg/cm2 b) 50-100 kg/cm2 c) 120-200 kg/cm2 d) 200 kg/cm2
Last Answer : c) 120-200 kg/cm2
Description : gnition delay is defined as the A)time between start of fuel injection and ignition of fuel B)time between end of fuel injection and ignition of fuel C)time between start of ignition and tdc D)time between completion of ignition and bdc
Last Answer : A)time between start of fuel injection and ignition of fuel
Description : High carbon steel having carbon content about (A) 0.25 % (B) 0.25 – 0.50 % (C) 0.50 – 1.5 % (D) 2.5 - 4.5 %
Last Answer : (C) 0.50 – 1.5 %
Description : Medium Carbon steel was carbon content about (A) 0.25 % (B) 0.25 – 0.50 % (C) 0.50 – 1.5 % (D) 2.5 – 4.5 %
Last Answer : (B) 0.25 – 0.50 %
Description : Carbon content in the cast iron is (A) 2.5 – 4.5 % (B) 0 – 0.25 % (C) 0.25 – 0.50 % (D) 0.50 – 1.5 %
Last Answer : (B) 0 – 0.25 %
Description : Mild steel is an alloy with carbon content a)0.25%. b)5% c)10%. d)25%
Last Answer : a)0.25%.
Description : Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more
Last Answer : a) Higher cylinder speed.
Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate
Last Answer : a)peripheral speed of the drum
Description : Flat planting predominates where a) Nature moisture content is favourable b) Rainfall is high to provide surface drainage c) Semi arid areas to conserve moisture d) None of the above
Last Answer : a) Nature moisture content is favourable
Description : Which of the following is not an important property of fuel oil/furnace oil? (A) Sulphur content (B) Viscosity (C) Aniline point (D) Flash point
Last Answer : (C) Aniline point
Description : Reid vapour pressure of gasoline is the measure of its (A) Pour point (B) Cloud point (C) Vapour locking tendency (D) Carbon residue
Last Answer : (C) Vapour locking tendency
Description : Define following: i) Oiliness ii) Volatility iii) Cloud point iv)Pour point
Last Answer : i) Oiliness: -It is defined as the power of an oil to maintain a continuous film under pressure while used a lubricant. ii) Volatility: - Volatility of oil is its tendency to vaporize with the ... iv) Pour point: It is defined as the temperature at which oil ceases to flow or pour on cooling
Description : Explain the following properties i) Pour point ii) Viscosity iii) Ignition quality iv) Fire point
Last Answer : i. Pour point: Pour point is the temperature below which the entire mass of fuel, solid or liquid together, freeze and thus cause flow of fuel impossible. Pour point is usually 5 to 10 °C below ... is the temperature at which the flash will sustain itself as a steady flame for at least five seconds.
Description : What is the unique state at which solid, liquid and gaseous phase can go co-exist in equilibrium? a. Triple point b. Critical point c. Boiling point d. Pour point
Last Answer : Triple point
Description : Fuel oil is subjected to visbreaking to reduce its (A) Pour point (B) Viscosity (C) Pressure drop on pumping (D) All (A), (B) and (C
Last Answer : (D) All (A), (B) and (C
Description : The type of restrained three point linkage system in which the depth of implement is automatically adjusted to maintain a pre selected constant draft is called : E. Automatic draft control system F. Precision control system G. Depth control system H. None of the above
Last Answer : E. Automatic draft control system
Description : he amount of liquid required for ground spraying of agricultural crops is : a.) 400-600L/ha b.) 200-400L/ha c.) 1000-2000L/ha d.) 600-800L/ha
Last Answer : a.) 400-600L/ha
Description : he shape of the gross surface of the tillage tool is designated as a) Micro shape c) Edge shape b) Macro shape d) Gross shape
Last Answer : b) Macro shape
Description : In case of liquid petrofuels, momentary combustion is observed at its (A) Flash point (B) Preheating temperature corresponding to viscosity of 25 centistokes (C) Flame temperature (D) Fire point
Last Answer : (A) Flash point
Description : Volumetric efficiency is affected by (A) Turbulence velocity and temperature of intake manifold (B) Efficiency of exhaust stroke (C) Valve timing overlap (D) All the above
Last Answer : (D) All the above
Description : 40 optimum working temperature for diesel engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c
Last Answer : ∙ 88-90°c
Description : ptimum working temperature for petrol engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c
Last Answer : ∙ 71-82°c
Description : The virtual hitch point of a directional implement is located at: a) Near the front axle b) 40 mm towards the rear axle c) At the power take off shaft d) Between two lower links
Last Answer : d) Between two lower links
Description : The optimum percentage of excess air for combustion depends upon the__________ of the fuel. (A) Type (solid, liquid or gaseous) (B) Calorific value (C) Sulphur content (D) Ignition temperature
Last Answer : (A) Type (solid, liquid or gaseous)
Last Answer : Kerosene Of water Than Light Says.
Description : Pour point of a petrofuel is (A) Multiple of 3°F (B) Multiple of 5°F (C) 5°C below the temperature at which oil ceases to flow (D) None of these
Last Answer : (C) 5°C below the temperature at which oil ceases to flow
Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above
Last Answer : B. L-head
Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above
Last Answer : d) None of the above
Description : Dead furrow open furrow is called when plowing is done by (a) Center to side (b) side to center method (c) one way plowing (d) none of the above
Last Answer : (b) side to center method
Description : Total force exerted upon the implement by a power unit called a)pull. B) draft C)side draft. D)unit draft
Last Answer : a)pull
Description : Horizontal component of pull perpendicular to the line of motion is called: A.Draft B.Side draft C.Transerve component D. Pull
Last Answer : B.Side draft
Description : A low mold board with gradual twist that completely invert the furrow slice with a minimum of breakup, thus covering vegetative matter thoroughly is called a. Stubble bottom b. sod bottom c. salted mould board d. general purpose bottom
Last Answer : b. sod bottom
Description : Equipment for placing seeding in the soil called: a) Seed drill b) Seed cum fertilizer drill c) Planter d) Transplanter
Last Answer : d) Transplanter
Description : Rotavator working in reverse direction for compacting soil and giving good touch to inter culturing is called a) Rotary tiller b) Power tiller c) Power harrow d) Treader
Last Answer : d) Treader
Description : A relative short and broad mould board is curved rather abruptly near the top resulting in a greater degree of pulverization is called a. Sod bottom b. Stubble bottom b. General bottom d. Slat bottom
Last Answer : b. General bottom
Description : A long jow mould board with a gradual twist (spiral) that completely inverts the furrow slice with a minimum of break up thus covering vegetative matter thoroughly is called a. Sod bottom b. Stubble bottom c. General bottom d. Slat bottom
Last Answer : a. Sod bottom
Description : The force that holds two particles of the different kind together is called as a) Adhesion c) Shear force b) Cohesion d) Compressive
Last Answer : a) Adhesion
Description : The force that holds two particles of the same kind together is called as a) Adhesion c) shear force b) cohesion d) compressive
Last Answer : b) cohesion