A heater takes 4 Amp at 250 volts. How much power does it consume?

A heater takes 4 Amp at 250 volts. How much power does it consume? A. 1 KWatt B. 2 KWatt C. 3 KWatt D. 4 KWatt 
by

2 Answers

Answer :

A heater takes 4 Amp at 250 volts. How much power does it consume?

1 KWatt

by

Answer :

Power= voltage* current

            = 4 * 250

            = 1000 watts

            = 1KW
by

Related questions

An immersion heater of 400 watts kept on for 5 hours will consume electrical power of a. 2KWh b. 20KWh c. 6KWh d. 12KWh

Description : An immersion heater of 400 watts kept on for 5 hours will consume electrical power of a. 2KWh b. 20KWh c. 6KWh d. 12KWh

Last Answer : a. 2KWh

When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the battery amp-hour rating C. the source of power for charging should be 2.5 volts per cell D. gassing within the battery decreases when nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Description : When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the ... nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Last Answer : Answer: C

Two bulbs marked 200 watt-250 volts and 100 watt-250 volts are joined...

Description : Two bulbs marked 200 watt-250 volts and 100 watt-250 volts are joined in series to 250 volts supply. Power consumed in circuit is 

Last Answer : Two bulbs marked 200 watt-250 volts and 100 watt-250 volts are joined in series to 250 volts supply. Power consumed in circuit is 67 watt.

A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw

Description : A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw

Last Answer : Answer: A

A three-phase alternator operates at 450 volts with a power factor of 0.8. If the ammeter indicates 250 amperes, what should be the KW meter reading? A. 90.00 KW B. 127.27 KW C. 155.70 KW D. 194.85 KW

Description : A three-phase alternator operates at 450 volts with a power factor of 0.8. If the ammeter indicates 250 amperes, what should be the KW meter reading? A. 90.00 KW B. 127.27 KW C. 155.70 KW D. 194.85 KW

Last Answer : Answer: C

In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days

Description : In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days

Last Answer : Answer: C

What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps

Description : What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps

Last Answer : Answer: B

What is the amp draw for a 3800 watt 240 volt water heater?

Description : What is the amp draw for a 3800 watt 240 volt water heater?

Last Answer : What is the answer ?

In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts

Description : In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts

Last Answer : Answer: D

A compound generator has a no-load voltage of 250 volts and a full-load voltage of 230 volts, and therefore, is considered to be _____________. A. flat compounded B. over compounded C. under compounded D. terminal compounded

Description : A compound generator has a no-load voltage of 250 volts and a full-load voltage of 230 volts, and therefore, is considered to be _____________. A. flat compounded B. over compounded C. under compounded D. terminal compounded

Last Answer : Answer: C

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

Express the following in more simple terms. (a) 250,000 volts, (b) 25,000,000 microvolts, (c) 0.001 millivolt.

Description : Express the following in more simple terms. (a) 250,000 volts, (b) 25,000,000 microvolts, (c) 0.001 millivolt.

Last Answer : (a) 250 kV, (b) 25 V, (c) 1µV

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

Which breakdown theory explains the action that takes place in a heavily doped PN-junction with a reverse bias of less than 5 volts?

Description : Which breakdown theory explains the action that takes place in a heavily doped PN-junction with a reverse bias of less than 5 volts?

Last Answer : Zener effect.

Transfer of heat energy from a heater coil to the cooking vessel takes place through the process of- (1) Convection only (2) Conduction and convection only (3) Radiation and convection only (4) Convection, conduction and radiation

Description : Transfer of heat energy from a heater coil to the cooking vessel takes place through the process of- (1) Convection only (2) Conduction and convection only (3) Radiation and convection only (4) Convection, conduction and radiation

Last Answer : (3) Radiation and convection only Explanation: Conduction is the transfer of heat energy by direct contact, convection is the movement of heat by actual motion of matter; radiation is the transfer of energy with the help of electromagnetic waves.

An artificial satellite is moving in a circular orbit of radius 42.250 km (approx). Calculate its linear velocity if takes 24 hour to revolve around earth.? -Science

Description : An artificial satellite is moving in a circular orbit of radius 42.250 km (approx). Calculate its linear velocity if takes 24 hour to revolve around earth.? -Science

Last Answer : Given r =42.250 km , T= 24 hour Linear velocity in circular motion is given by v=2πrT=2×3.14×42.25024=11.05km/hrv=2πrT=2×3.14×42.25024=11.05km/hr

A 250 m goods train takes 50 s to cross a person who is going in the same direction with the speed of 8 km/h. After crossing that person, the train can reach next station in 2 hr. How long that person takes to reach that station after being crossed by them? A) 2 ½ hr B) 5hr C) 3 1/2hr D) 1hr

Description : A 250 m goods train takes 50 s to cross a person who is going in the same direction with the speed of 8 km/h. After crossing that person, the train can reach next station in 2 hr. How long that person takes to reach that station after being crossed by them? A) 2 ½ hr B) 5hr C) 3 1/2hr D) 1hr

Last Answer : ANSWER:A Explanation:  Speed of the person = 8 kmph  = (8*5/18)m/s  = 20/9 m/s  Then relative speed of train = (x-20/9)m/s  As train takes 50 sec to cross the person  Therefore 50 =250/(x-20/ ... 20,000 m  = 20 km Thus time taken by the person to cover the distance of 20km= 20/8 hr=2 ½ hr

Three identical resistors connected in star consume 5000 W. If the resistors are connected in

Description : Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be

Last Answer : Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be 15000 W

State the function of super heater of a thermal power plant.

Description : State the function of super heater of a thermal power plant. 

Last Answer : Function of Super heater: -  Its function is to increase the temperature of steam by absorbing heat from exhausted hot flue gases.

The Brake Horse power of the motor (efficiency 60%) required for a pump of capacity 0.075 cumec for a total lift of 12 m, is A. 10 B. 15 C. 20 D. 25 Q No: 44 Aerobic bacterias A. Flourish in the presence of free oxygen B. Consume organic matter as their food C. Oxidise organic matter in sewage D. All the above

Description : The Brake Horse power of the motor (efficiency 60%) required for a pump of capacity 0.075 cumec for a total lift of 12 m, is A. 10 B. 15 C. 20 D. 25 Q No: 44 Aerobic bacterias A. ... presence of free oxygen B. Consume organic matter as their food C. Oxidise organic matter in sewage D. All the above

Last Answer : ANS: D

Which of following consume minimum power (A) TTL. (B) CMOS. (C) DTL. (D) RTL.

Description : Which of following consume minimum power (A) TTL. (B) CMOS. (C) DTL. (D) RTL.

Last Answer : Ans: B CMOS consumes minimum power as in CMOS one p-MOS & one n-MOS transistors are connected in complimentary mode, such that one device is ON & one is OFF.

CMOS circuits consume power (A) Equal to TTL (B) Less than TTL (C) Twice of TTL (D) Thrice of TTL

Description : CMOS circuits consume power (A) Equal to TTL (B) Less than TTL (C) Twice of TTL (D) Thrice of TTL

Last Answer : Ans: B As in CMOS one device is ON & one is Always OFF so power consumption is low.

Two identical resistors are connected in parallel and consume 200 watts together. A third identical resistor is added in parallel. The total power consumed is: w) 100 watts x) 200 watts y) 300 watts z) 400 watts

Description : Two identical resistors are connected in parallel and consume 200 watts together. A third identical resistor is added in parallel. The total power consumed is: w) 100 watts x) 200 watts y) 300 watts z) 400 watts

Last Answer : ANSWER: Y -- 300 WATTS

What would be the total power drawn from the supply, when two heaters, rated at 1000 W, 250 V each ...

Description : What would be the total power drawn from the supply, when two heaters, rated at 1000 W, 250 V each are connected in series across a 250 V, 50 Hz supply?  (A) 1000 W (B) 500 W (C) 250 W (D) 2000 W

Last Answer : Answer:B. One heater 1000W, 250V resistance is 62.5ohm. Two Series connected heaters so, 62.5+62.5=125ohm. Current in the series circuit is 250V/125ohm = 2A. Total power drawn = current2 X R = 22 x 125 = 500W.

What is amp?

Last Answer : Amp is ampere which is a unit of current.

Define the following terms related to Op-Amp: i) CMRR ii) SVRR

Description : Define the following terms related to Op-Amp: i) CMRR ii) SVRR

Last Answer : Definition:- i) SVRR: It is defined as the ratio of change of input offset voltage to the change in one supply voltage while keeping other supply voltage constant. Ideally,SVRR=0  ii)CMMR:-The ... gain should exceed common-mode gain, this will be a positive number, and the higher the better.

State any two characteristics of an ideal Op-amp.

Description : State any two characteristics of an ideal Op-amp.

Last Answer : Characteristics of Op-amp: i) Input offset voltage ii) Input offset current iii) Input bias current iv) Differential input resistance v) Input capacitance vi) CMRR-common mode rejection ration vii) ... voltage rejection ratio(SVRR) viii) Output resistance ix) Voltage gain x) Bandwidth xi) Slew rate

Draw and explain the Op-amp based subtractor

Description : Draw and explain the Op-amp based subtractor

Last Answer : Working The subtractor circuit is a basic op-amp circuit whose output voltage is the difference between two input voltages.  In the above circuit, the two input voltages are V1 and V2.  The op amp is used ... When differential gain is 1, ie Rf = R,  the output voltage is Vo = (V2 - V1).

Draw the diagram of zero crossing detector using op-amp and explain its working.

Description : Draw the diagram of zero crossing detector using op-amp and explain its working.

Last Answer : The zero crossing detector circuit is an important application of the op-amp comparator circuit. It can also be called as the sine to square wave converter. Anyone of the inverting or non-inverting ... the possibility of any false zero crossing due to noise voltages at the op-amp input.

An OP amp has an open loop gain of 1,00,000. If the feedback fraction is 0.02, the approximate closed loop...

Description : An OP amp has an open loop gain of 1,00,000. If the feedback fraction is 0.02, the approximate closed loop gain is (a) 1 (b) 1,00,000 (c) 50 (d) 0.02

Last Answer : The closed loop gain Ag = G/(1+G*f) Where G is the open loop gain and f is the feedback fraction  So Ag = 49.975

An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave ...

Description : An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave amplitude is (a) 8V (b) 4.82 V (c) 2.02 V (d) 1.592 V

Last Answer : Slew rate = 2πfv where v is the amplitude V=(1/2π*0.1) = 1.592V

What is the Output voltage of Op-amp for input voltage of Vi1=150 μV,Vi2=140 μV if the amplifier ...

Description : What is the Output voltage of Op-amp for input voltage of Vi1=150 μV,Vi2=140 μV if the amplifier has differential gain of Ad=4000 and value of CMRR is 100. 

Last Answer : i don know

Amp hour is the unit for measuring

Last Answer : Amp hour is the unit for measuring Capacity of a cell.

An electric heating element supplied with 120 volts draws 15 amps. How much power will be consumed? A. 15 watts B. 45.57 watts C. 180 watts D. 1800 watts

Description : An electric heating element supplied with 120 volts draws 15 amps. How much power will be consumed? A. 15 watts B. 45.57 watts C. 180 watts D. 1800 watts

Last Answer : Answer: D

A lamp of 100W at 200V is supplied current at 100 volts. It will be equivalent to the lamp of:

Description : A lamp of 100W at 200V is supplied current at 100 volts. It will be equivalent to the lamp of:   a. 50W b. 40W c. 25W d. 10W 

Last Answer : A lamp of 100W at 200V is supplied current at 100 volts. It will be equivalent to the lamp of: 25W

A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts

Description : A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts applied to the primary. What is the voltage across the secondary?  (A) 30 Volts (B) 480 Volts (C) 120 Volts (D) 60 Volts

Last Answer : A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts applied to the primary. What is the voltage across the secondary?  (A) 30 Volts (B) 480 Volts (C) 120 Volts (D) 60 Volts

A 400/200 volts transformer has pu impedance of 0.05. The HV side voltage required to circulate full load...

Description : A 400/200 volts transformer has pu impedance of 0.05. The HV side voltage required to circulate full load current during short circuit test is

Last Answer : A 400/200 volts transformer has pu impedance of 0.05. The HV side voltage required to circulate full load current during short circuit test is 20 V

The Lamp resistance of a mini-torch light, operating on 1.5 volts is classified as _____________resistance.

Description : The Lamp resistance of a mini-torch light, operating on 1.5 volts is classified as _____________resistance. A. Low B. Medium C. High D. None of these 

Last Answer : The Lamp resistance of a mini-torch light, operating on 1.5 volts is classified as Medium resistance.

A series R-L circuit is suddenly connected to d.c. voltage source of V volts. The current in this series ...

Description : A series R-L circuit is suddenly connected to d.c. voltage source of V volts. The current in this series circuit, just after the switch is closed, is equal to (1) Zero (2) V/L (3) V/C (4) V.L/C 

Last Answer : When is a series RLC circuit is over damped

if voltage is 230 Volts , frequency is 50 Hz and current is 1 ampere then what will be the resistance?

Description : if voltage is 230 Volts , frequency is 50 Hz and current is 1 ampere then what will be the resistance?

Last Answer : As V = 230v and I = 1A Therfore by ohm's law V =IR R = V/I =230/1 =230 ohm

how can we express 0.40 kV in volts?

Description : how can we express 0.40 kV in volts?

Last Answer : Kvx1000=400v

How much spit do we consume a day lol?

Description : How much spit do we consume a day lol?

Last Answer : Your salivary glands make as much as a quart of saliva each day. Saliva is important to lubricate your mouth, help with swallowing, protect your teeth against bacteria, and aid in the digestion of food.

How much electricity does a 195-liter fridge consume?

Description : How much electricity does a 195-liter fridge consume?

Last Answer : That is like asking how fast a car can go. A new refrigerator is so much more efficient than one made fifteen years ago that you can save money by throwing out your old one and buying a new one. The reduced power consumption will pay for the change in the first year.

How much lead can a person consume?

Description : How much lead can a person consume?

Last Answer : Not much. Could kill you though

How much protein per pound of body weight should I consume when starting bodybuilding?

Description : How much protein per pound of body weight should I consume when starting bodybuilding?

Last Answer : For body building purposes the recommended amount of protein to be consumed daily should be 1.7/1.8 grams of protein per kilogram which equals 2.2 pounds of bodyweight. This is almost double the Rda recommended by the Fda which recommends .8 grams per kilogram of lean body mass.

How much energy does a 70 inch LED TV consume?

Description : How much energy does a 70 inch LED TV consume?

Last Answer : A 70 inch LED television is going to consume about double the energy of a 30 inch LED television. It also depends on what brand of television it is, and if it's energy star approved.

I want to know the benefits of a low sodium diet and why sodium is so bad for you if you consume too much.?

Description : I want to know the benefits of a low sodium diet and why sodium is so bad for you if you consume too much.?

Last Answer : A low sodium diet plan is beneficial in that it helps stave off heart problems. Sodium is one of the many factors that raise your cholesterol levels and can lead to heart attacks.

How much Potassium can a human consume daily?

Description : How much Potassium can a human consume daily?

Last Answer : It is important to get enough potassium i your daily diet. The recommended amount of potassium is 4.7g a day. However, if you exercise a lot, you need even more potassium.

What organisms groups was originally considered an animal by zoologists, since it can move rapidly like an animal and consumes other organisms for food, and was also claimed to be a plant by botanists since it can consume energy much like a plant?

Description : What organisms groups was originally considered an animal by zoologists, since it can move rapidly like an animal and consumes other organisms for food, and was also claimed to be a plant by botanists since it can consume energy much like a plant?

Last Answer : euglena

All of the following are the limitations of televised instruction except (a) Televised lesson moves at a fixed speed and thus can not take the individual differences of students into account (b) It does not permit the exchange of ideas between the teachers and taught (c) It does not properly help the students in making the materials clearly understood (d) Experts consume much time in planning and preparation of the programme.

Description : All of the following are the limitations of televised instruction except (a) Televised lesson moves at a fixed speed and thus can not take the individual differences of students into account ... materials clearly understood (d) Experts consume much time in planning and preparation of the programme.

Last Answer : (c) It does not properly help the students in making the materials clearly understood